Now that user space can specify additional attributes of port group
entries such as filter mode and source list, it makes sense to allow
user space to atomically modify these attributes by replacing entries
instead of forcing user space to delete the entries and add them back.
Replace MDB port group entries when the 'NLM_F_REPLACE' flag is
specified in the netlink message header.
When a (*, G) entry is replaced, update the following attributes: Source
list, state, filter mode, protocol and flags. If the entry is temporary
and in EXCLUDE mode, reset the group timer to the group membership
interval. If the entry is temporary and in INCLUDE mode, reset the
source timers of associated sources to the group membership interval.
Examples:
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.2 filter_mode include
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.2 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode include source_list 192.0.2.2/0.00,192.0.2.1/0.00 proto static 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.3 filter_mode exclude proto zebra
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude source_list 192.0.2.3/0.00,192.0.2.1/0.00 proto zebra 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 temp source_list 192.0.2.4,192.0.2.3 filter_mode include proto bgp
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.4 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 temp filter_mode include source_list 192.0.2.4/259.44,192.0.2.3/259.44 proto bgp 0.00
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the 'MDBE_ATTR_RTPORT' attribute to allow user space to specify the
routing protocol of the MDB port group entry. Enforce a minimum value of
'RTPROT_STATIC' to prevent user space from using protocol values that
should only be set by the kernel (e.g., 'RTPROT_KERNEL'). Maintain
backward compatibility by defaulting to 'RTPROT_STATIC'.
The protocol is already visible to user space in RTM_NEWMDB responses
and notifications via the 'MDBA_MDB_EATTR_RTPROT' attribute.
The routing protocol allows a routing daemon to distinguish between
entries configured by it and those configured by the administrator. Once
MDB flush is supported, the protocol can be used as a criterion
according to which the flush is performed.
Examples:
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto kernel
Error: integer out of range.
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto static
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent proto zebra
# bridge mdb add dev br0 port dummy10 grp 239.1.1.2 permanent source_list 198.51.100.1,198.51.100.2 filter_mode include proto 250
# bridge -d mdb show
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.2 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.1 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 permanent filter_mode include source_list 198.51.100.2/0.00,198.51.100.1/0.00 proto 250
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude proto static
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for allowing user space to add (*, G) entries with a
source list and associated filter mode, add the necessary plumbing to
handle such requests.
Extend the MDB configuration structure with a currently empty source
array and filter mode that is currently hard coded to EXCLUDE.
Add the source entries and the corresponding (S, G) entries before
making the new (*, G) port group entry visible to the data path.
Handle the creation of each source entry in a similar fashion to how it
is created from the data path in response to received Membership
Reports: Create the source entry, arm the source timer (if needed), add
a corresponding (S, G) forwarding entry and finally mark the source
entry as installed (by user space).
Add the (S, G) entry by populating an MDB configuration structure and
calling br_mdb_add_group_sg() as if a new entry is created by user
space, with the sole difference that the 'src_entry' field is set to
make sure that the group timer of such entries is never armed.
Note that it is not currently possible to add more than 32 source
entries to a port group entry. If this proves to be a problem we can
either increase 'PG_SRC_ENT_LIMIT' or avoid forcing a limit on entries
created by user space.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
User space will soon be able to install a (*, G) with a source list,
prompting the creation of a (S, G) entry for each source.
In this case, the group timer of the (S, G) entry should never be set.
Solve this by adding a new field to the MDB configuration structure that
denotes whether the (S, G) corresponds to a source or not.
The field will be set in a subsequent patch where br_mdb_add_group_sg()
is called in order to create a (S, G) entry for each user provided
source.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few places where the bridge driver differentiates between
(S, G) entries installed by the kernel (in response to Membership
Reports) and those installed by user space. One of them is when deleting
an (S, G) entry corresponding to a source entry that is being deleted.
While user space cannot currently add a source entry to a (*, G), it can
add an (S, G) entry that later corresponds to a source entry created by
the reception of a Membership Report. If this source entry is later
deleted because its source timer expired or because the (*, G) entry is
being deleted, the bridge driver will not delete the corresponding (S,
G) entry if it was added by user space as permanent.
This is going to be a problem when the ability to install a (*, G) with
a source list is exposed to user space. In this case, when user space
installs the (*, G) as permanent, then all the (S, G) entries
corresponding to its source list will also be installed as permanent.
When user space deletes the (*, G), all the source entries will be
deleted and the expectation is that the corresponding (S, G) entries
will be deleted as well.
Solve this by introducing a new source entry flag denoting that the
entry was installed by user space. When the entry is deleted, delete the
corresponding (S, G) entry even if it was installed by user space as
permanent, as the flag tells us that it was installed in response to the
source entry being created.
The flag will be set in a subsequent patch where source entries are
created in response to user requests.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose __br_multicast_del_group_src() which is symmetric to
br_multicast_new_group_src() and does not remove the installed {S, G}
forwarding entry, unlike br_multicast_del_group_src().
The function will be used in the error path when user space was able to
add a new source entry, but failed to install a corresponding forwarding
entry.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, new group source entries are only created in response to
received Membership Reports. Subsequent patches are going to allow user
space to install (*, G) entries with a source list.
As a preparatory step, expose br_multicast_new_group_src() so that it
could later be invoked from the MDB code (i.e., br_mdb.c) that handles
RTM_NEWMDB messages.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'group' argument is not modified, so mark it as 'const'. It will
allow us to constify arguments of the callers of this function in future
patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netlink attributes are currently passed deep in the MDB creation call
chain, making it difficult to add new attributes. In addition, some
validity checks are performed under the multicast lock although they can
be performed before it is ever acquired.
As a first step towards solving these issues, parse the RTM_{NEW,DEL}MDB
messages into a configuration structure, relieving other functions from
the need to handle raw netlink attributes.
Subsequent patches will convert the MDB code to use this configuration
structure.
This is consistent with how other rtnetlink objects are handled, such as
routes and nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the bridge is offloaded to hardware, FDB entries are learned and
aged-out by the hardware. Some device drivers synchronize the hardware
and software FDBs by generating switchdev events towards the bridge.
When a port is locked, the hardware must not learn autonomously, as
otherwise any host will blindly gain authorization. Instead, the
hardware should generate events regarding hosts that are trying to gain
authorization and their MAC addresses should be notified by the device
driver as locked FDB entries towards the bridge driver.
Allow device drivers to notify the bridge driver about such entries by
extending the 'switchdev_notifier_fdb_info' structure with the 'locked'
bit. The bit can only be set by device drivers and not by the bridge
driver.
Prevent a locked entry from being installed if MAB is not enabled on the
bridge port.
If an entry already exists in the bridge driver, reject the locked entry
if the current entry does not have the "locked" flag set or if it points
to a different port. The same semantics are implemented in the software
data path.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hosts that support 802.1X authentication are able to authenticate
themselves by exchanging EAPOL frames with an authenticator (Ethernet
bridge, in this case) and an authentication server. Access to the
network is only granted by the authenticator to successfully
authenticated hosts.
The above is implemented in the bridge using the "locked" bridge port
option. When enabled, link-local frames (e.g., EAPOL) can be locally
received by the bridge, but all other frames are dropped unless the host
is authenticated. That is, unless the user space control plane installed
an FDB entry according to which the source address of the frame is
located behind the locked ingress port. The entry can be dynamic, in
which case learning needs to be enabled so that the entry will be
refreshed by incoming traffic.
There are deployments in which not all the devices connected to the
authenticator (the bridge) support 802.1X. Such devices can include
printers and cameras. One option to support such deployments is to
unlock the bridge ports connecting these devices, but a slightly more
secure option is to use MAB. When MAB is enabled, the MAC address of the
connected device is used as the user name and password for the
authentication.
For MAB to work, the user space control plane needs to be notified about
MAC addresses that are trying to gain access so that they will be
compared against an allow list. This can be implemented via the regular
learning process with the sole difference that learned FDB entries are
installed with a new "locked" flag indicating that the entry cannot be
used to authenticate the device. The flag cannot be set by user space,
but user space can clear the flag by replacing the entry, thereby
authenticating the device.
Locked FDB entries implement the following semantics with regards to
roaming, aging and forwarding:
1. Roaming: Locked FDB entries can roam to unlocked (authorized) ports,
in which case the "locked" flag is cleared. FDB entries cannot roam
to locked ports regardless of MAB being enabled or not. Therefore,
locked FDB entries are only created if an FDB entry with the given {MAC,
VID} does not already exist. This behavior prevents unauthenticated
devices from disrupting traffic destined to already authenticated
devices.
2. Aging: Locked FDB entries age and refresh by incoming traffic like
regular entries.
3. Forwarding: Locked FDB entries forward traffic like regular entries.
If user space detects an unauthorized MAC behind a locked port and
wishes to prevent traffic with this MAC DA from reaching the host, it
can do so using tc or a different mechanism.
Enable the above behavior using a new bridge port option called "mab".
It can only be enabled on a bridge port that is both locked and has
learning enabled. Locked FDB entries are flushed from the port once MAB
is disabled. A new option is added because there are pure 802.1X
deployments that are not interested in notifications about locked FDB
entries.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add extack support to .ndo_fdb_del in netdevice.h and
all related methods.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for fdb flush filtering based on ndm flags and state. NDM
state and flags are mapped to bridge-specific flags and matched
according to the specified masks. NTF_USE is used to represent
added_by_user flag since it sets it on fdb add and we don't have a 1:1
mapping for it. Only allowed bits can be set, NTF_SELF and NTF_MASTER are
ignored.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to specify exactly which fdbs to be flushed. They are
described by a new structure - net_bridge_fdb_flush_desc. Currently it
can match on port/bridge ifindex, vlan id and fdb flags. It is used to
describe the existing dynamic fdb flush operation. Note that this flush
operation doesn't treat permanent entries in a special way (fdb_delete vs
fdb_delete_local), it will delete them regardless if any port is using
them, so currently it can't directly replace deletes which need to handle
that case, although we can extend it later for that too.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a minimal ndo_fdb_del_bulk implementation which flushes all entries.
Support for more fine-grained filtering will be added in the following
patches.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to change the port state in a given MSTI by extending
the bridge port netlink interface (RTM_SETLINK on PF_BRIDGE).The
proposed iproute2 interface would be:
bridge mst set dev <PORT> msti <MSTI> state <STATE>
Current states in all applicable MSTIs can also be dumped via a
corresponding RTM_GETLINK. The proposed iproute interface looks like
this:
$ bridge mst
port msti
vb1 0
state forwarding
100
state disabled
vb2 0
state forwarding
100
state forwarding
The preexisting per-VLAN states are still valid in the MST
mode (although they are read-only), and can be queried as usual if one
is interested in knowing a particular VLAN's state without having to
care about the VID to MSTI mapping (in this example VLAN 20 and 30 are
bound to MSTI 100):
$ bridge -d vlan
port vlan-id
vb1 10
state forwarding mcast_router 1
20
state disabled mcast_router 1
30
state disabled mcast_router 1
40
state forwarding mcast_router 1
vb2 10
state forwarding mcast_router 1
20
state forwarding mcast_router 1
30
state forwarding mcast_router 1
40
state forwarding mcast_router 1
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow a VLAN to move out of the CST (MSTI 0), to an independent tree.
The user manages the VID to MSTI mappings via a global VLAN
setting. The proposed iproute2 interface would be:
bridge vlan global set dev br0 vid <VID> msti <MSTI>
Changing the state in non-zero MSTIs is still not supported, but will
be addressed in upcoming changes.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to switch from the current per-VLAN STP mode to an MST
mode.
Up to this point, per-VLAN STP states where always isolated from each
other. This is in contrast to the MSTP standard (802.1Q-2018, Clause
13.5), where VLANs are grouped into MST instances (MSTIs), and the
state is managed on a per-MSTI level, rather that at the per-VLAN
level.
Perhaps due to the prevalence of the standard, many switching ASICs
are built after the same model. Therefore, add a corresponding MST
mode to the bridge, which we can later add offloading support for in a
straight-forward way.
For now, all VLANs are fixed to MSTI 0, also called the Common
Spanning Tree (CST). That is, all VLANs will follow the port-global
state.
Upcoming changes will make this actually useful by allowing VLANs to
be mapped to arbitrary MSTIs and allow individual MSTI states to be
changed.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD
event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases:
- a struct net_bridge_vlan got created
- an existing struct net_bridge_vlan was modified
This makes it impossible for switchdev drivers to properly balance
PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to
happen, we must provide a way for drivers to distinguish between a
VLAN with changed flags and a new one.
Annotate struct switchdev_obj_port_vlan with a "bool changed" that
distinguishes the 2 cases above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to first check if the context is a vlan one, then we need to
check the global bridge multicast vlan snooping flag, and finally the
vlan's multicast flag, otherwise we will unnecessarily enable vlan mcast
processing (e.g. querier timers).
Fixes: 7b54aaaf53 ("net: bridge: multicast: add vlan state initialization and control")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20211228153142.536969-1-nikolay@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if startup query interval is set too low in combination with
large number of startup queries and we have multiple bridges or even a
single bridge with multiple querier vlans configured we can crash the
machine. Add a 1 second minimum which must be enforced by overwriting the
value if set lower (i.e. without returning an error) to avoid breaking
user-space. If that happens a log message is emitted to let the admin know
that the startup interval has been set to the minimum. It doesn't make
sense to make the startup interval lower than the normal query interval
so use the same value of 1 second. The issue has been present since these
intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if query interval is set too low and we have multiple
bridges or even a single bridge with multiple querier vlans configured
we can crash the machine. Add a 1 second minimum which must be enforced
by overwriting the value if set lower (i.e. without returning an error) to
avoid breaking user-space. If that happens a log message is emitted to let
the administrator know that the interval has been set to the minimum.
The issue has been present since these intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_switchdev_mdb_notify() is conditionally compiled only when
CONFIG_NET_SWITCHDEV=y and CONFIG_BRIDGE_IGMP_SNOOPING=y. It is called
from br_mdb.c, which is conditionally compiled only when
CONFIG_BRIDGE_IGMP_SNOOPING=y.
The shim definition of br_switchdev_mdb_notify() is therefore needed for
the case where CONFIG_NET_SWITCHDEV=n, however we mistakenly put it
there for the case where CONFIG_BRIDGE_IGMP_SNOOPING=n. This results in
build failures when CONFIG_BRIDGE_IGMP_SNOOPING=y and
CONFIG_NET_SWITCHDEV=n.
To fix this, put the shim definition right next to
br_switchdev_fdb_notify(), which is properly guarded by NET_SWITCHDEV=n.
Since this is called only from br_mdb.c, we need not take any extra
safety precautions, when NET_SWITCHDEV=n and BRIDGE_IGMP_SNOOPING=n,
this shim definition will be absent but nobody will be needing it.
Fixes: 9776457c78 ("net: bridge: mdb: move all switchdev logic to br_switchdev.c")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211029223606.3450523-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Function br_get_link_af_size_filtered() calls br_cfm_{,peer}_mep_count()
that return a count. When BRIDGE_CFM is not enabled these functions
simply return -EOPNOTSUPP but do not modify count parameter and
calling function then works with uninitialized variables.
Modify these inline functions to return zero in count parameter.
Fixes: b6d0425b81 ("bridge: cfm: Netlink Notifications.")
Cc: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions:
br_mdb_complete
br_switchdev_mdb_populate
br_mdb_replay_one
br_mdb_queue_one
br_mdb_replay
br_mdb_switchdev_host_port
br_mdb_switchdev_host
br_switchdev_mdb_notify
are only accessible from code paths where CONFIG_NET_SWITCHDEV is
enabled. So move them to br_switchdev.c, in order for that code to be
compiled out if that config option is disabled.
Note that br_switchdev.c gets build regardless of whether
CONFIG_BRIDGE_IGMP_SNOOPING is enabled or not, whereas br_mdb.c only got
built when CONFIG_BRIDGE_IGMP_SNOOPING was enabled. So to preserve
correct compilation with CONFIG_BRIDGE_IGMP_SNOOPING being disabled, we
must now place an #ifdef around these functions in br_switchdev.c.
The offending bridge data structures that need this are
br->multicast_lock and br->mdb_list, these are also compiled out of
struct net_bridge when CONFIG_BRIDGE_IGMP_SNOOPING is turned off.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_vlan_replay() is relevant only if CONFIG_NET_SWITCHDEV is enabled, so
move it to br_switchdev.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_vlan_replay() needs this, and we're preparing to move it to
br_switchdev.c, which will be compiled regardless of whether or not
CONFIG_BRIDGE_VLAN_FILTERING is enabled.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_fdb_replay is only called from switchdev code paths, so it makes
sense to be disabled if switchdev is not enabled in the first place.
As opposed to br_mdb_replay and br_vlan_replay which might be turned off
depending on bridge support for multicast and VLANs, FDB support is
always on. So moving br_mdb_replay and br_vlan_replay inside
br_switchdev.c would mean adding some #ifdef's in br_switchdev.c, so we
keep those where they are.
The reason for the movement is that in future changes there will be some
code reuse between br_switchdev_fdb_notify and br_fdb_replay.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fdb_insert() is a wrapper over fdb_insert() that also takes the
bridge hash_lock.
With fdb_insert() being renamed to fdb_add_local(), rename
br_fdb_insert() to br_fdb_add_local().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added IGMPv3 support I decided to follow the RFC for computing
the GMI dynamically:
" 8.4. Group Membership Interval
The Group Membership Interval is the amount of time that must pass
before a multicast router decides there are no more members of a
group or a particular source on a network.
This value MUST be ((the Robustness Variable) times (the Query
Interval)) plus (one Query Response Interval)."
But that actually is inconsistent with how the bridge used to compute it
for IGMPv2, where it was user-configurable that has a correct default value
but it is up to user-space to maintain it. This would make it consistent
with the other timer values which are also maintained correct by the user
instead of being dynamically computed. It also changes back to the previous
user-expected GMI behaviour for IGMPv3 queries which were supported before
IGMPv3 was added. Note that to properly compute it dynamically we would
need to add support for "Robustness Variable" which is currently missing.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: 0436862e41 ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence count bridge_mcast_querier::seq is protected by
net_bridge::multicast_lock but seqcount_init() does not associate the
seqcount with the lock. This leads to a warning on PREEMPT_RT because
preemption is still enabled.
Let seqcount_init() associate the seqcount with lock that protects the
write section. Remove lockdep_assert_held_once() because lockdep already checks
whether the associated lock is held.
Fixes: 67b746f94f ("net: bridge: mcast: make sure querier port/address updates are consistent")
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210928141049.593833-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The per-vlan router option controls the port/vlan and host vlan entries'
mcast router config. The global option controlled only the host vlan
config, but that is unnecessary and incosistent as it's not really a
global vlan option, but rather bridge option to control host router
config, so convert BRIDGE_VLANDB_GOPTS_MCAST_ROUTER to
BRIDGE_VLANDB_ENTRY_MCAST_ROUTER which can be used to control both host
vlan and port vlan mcast router config.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change br_multicast_set_port_router to take port multicast context as
its first argument so we can later use it to control port/vlan mcast
router option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing vlan mcast state by br_multicast_toggle_vlan it iterates
over all ports and enables/disables the port mcast ctx based on the new
state, but I forgot to update the host vlan (bridge master vlan entry)
with the new state so it will be left out. Also that function is not
used outside of br_multicast.c, so make it static.
Fixes: f4b7002a70 ("net: bridge: add vlan mcast snooping knob")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a global vlan notification we should account for the number
of router ports when allocating the skb, otherwise we might end up
losing notifications.
Fixes: dc002875c2 ("net: bridge: vlan: use br_rports_fill_info() to export mcast router ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping global IPv4 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IP_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IP_PORT] - bridge port ifindex where the querier was
seen (set only if external querier)
`[BRIDGE_QUERIER_IP_OTHER_TIMER] - other querier timeout
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a sequence counter to make sure port/address updates can be read
consistently without requiring the bridge multicast_lock. We need to
zero out the port and address when the other querier has expired and
we're about to select ourselves as querier. br_multicast_read_querier
will be used later when dumping querier state. Updates are done only
with the multicast spinlock and softirqs disabled, while reads are done
from process context and from softirqs (due to notifications).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a querier port is detected its net_bridge_port pointer is
recorded, but it's used only for comparisons so it's fine to have stale
pointer, in order to dereference and use the port pointer a proper
accounting of its usage must be implemented adding unnecessary
complexity. To solve the problem we can just store the netdevice ifindex
instead of the port pointer and retrieve the bridge port. It is a best
effort and the device needs to be validated that is still part of that
bridge before use, but that is small price to pay for avoiding querier
reference counting for each port/vlan.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embed the standard multicast router port export by br_rports_fill_info()
into a new global vlan attribute BRIDGE_VLANDB_GOPTS_MCAST_ROUTER_PORTS.
In order to have the same format for the global bridge mcast context and
the per-vlan mcast context we need a double-nesting:
- BRIDGE_VLANDB_GOPTS_MCAST_ROUTER_PORTS
- MDBA_ROUTER
Currently we don't compare router lists, if any router port exists in
the bridge mcast contexts we consider their option sets as different and
export them separately.
In addition we export the router port vlan id when dumping similar to
the router port notification format.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast router state
which is used for the bridge itself. We just need to pass multicast context
to br_multicast_set_router instead of bridge device and the rest of the
logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast querier state.
We just need to pass multicast context to br_multicast_set_querier
instead of bridge device and the rest of the logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a minor optimization and better behaviour to make sure querier and
query sending routines affect only the matching multicast context
depending if vlan snooping is enabled (vlan ctx vs bridge ctx).
It also avoids sending unnecessary extra query packets.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to have the querier state per multicast context in order to have
per-vlan control, so remove the internal option bit and move it to the
multicast context. Also annotate the lockless reads of the new variable.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast startup query
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast query response
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast query interval
option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
