* arm64/for-next/perf:
docs: perf: Fix warning from 'make htmldocs' in hisi-pmu.rst
docs: perf: Add new description for HiSilicon UC PMU
drivers/perf: hisi: Add support for HiSilicon UC PMU driver
drivers/perf: hisi: Add support for HiSilicon H60PA and PAv3 PMU driver
perf: arm_cspmu: Add missing MODULE_DEVICE_TABLE
perf/arm-cmn: Add sysfs identifier
perf/arm-cmn: Revamp model detection
perf/arm_dmc620: Add cpumask
dt-bindings: perf: fsl-imx-ddr: Add i.MX93 compatible
drivers/perf: imx_ddr: Add support for NXP i.MX9 SoC DDRC PMU driver
perf/arm_cspmu: Decouple APMT dependency
perf/arm_cspmu: Clean up ACPI dependency
ACPI/APMT: Don't register invalid resource
perf/arm_cspmu: Fix event attribute type
perf: arm_cspmu: Set irq affinitiy only if overflow interrupt is used
drivers/perf: hisi: Don't migrate perf to the CPU going to teardown
drivers/perf: apple_m1: Force 63bit counters for M2 CPUs
perf/arm-cmn: Fix DTC reset
perf: qcom_l2_pmu: Make l2_cache_pmu_probe_cluster() more robust
perf/arm-cci: Slightly optimize cci_pmu_sync_counters()
* for-next/kpti:
: Simplify KPTI trampoline exit code
arm64: entry: Simplify tramp_alias macro and tramp_exit routine
arm64: entry: Preserve/restore X29 even for compat tasks
* for-next/missing-proto-warn:
: Address -Wmissing-prototype warnings
arm64: add alt_cb_patch_nops prototype
arm64: move early_brk64 prototype to header
arm64: signal: include asm/exception.h
arm64: kaslr: add kaslr_early_init() declaration
arm64: flush: include linux/libnvdimm.h
arm64: module-plts: inline linux/moduleloader.h
arm64: hide unused is_valid_bugaddr()
arm64: efi: add efi_handle_corrupted_x18 prototype
arm64: cpuidle: fix #ifdef for acpi functions
arm64: kvm: add prototypes for functions called in asm
arm64: spectre: provide prototypes for internal functions
arm64: move cpu_suspend_set_dbg_restorer() prototype to header
arm64: avoid prototype warnings for syscalls
arm64: add scs_patch_vmlinux prototype
arm64: xor-neon: mark xor_arm64_neon_*() static
* for-next/iss2-decode:
: Add decode of ISS2 to data abort reports
arm64/esr: Add decode of ISS2 to data abort reporting
arm64/esr: Use GENMASK() for the ISS mask
* for-next/kselftest:
: Various arm64 kselftest improvements
kselftest/arm64: Log signal code and address for unexpected signals
kselftest/arm64: Add a smoke test for ptracing hardware break/watch points
* for-next/misc:
: Miscellaneous patches
arm64: alternatives: make clean_dcache_range_nopatch() noinstr-safe
arm64: hibernate: remove WARN_ON in save_processor_state
arm64/fpsimd: Exit streaming mode when flushing tasks
arm64: mm: fix VA-range sanity check
arm64/mm: remove now-superfluous ISBs from TTBR writes
arm64: consolidate rox page protection logic
arm64: set __exception_irq_entry with __irq_entry as a default
arm64: syscall: unmask DAIF for tracing status
arm64: lockdep: enable checks for held locks when returning to userspace
arm64/cpucaps: increase string width to properly format cpucaps.h
arm64/cpufeature: Use helper for ECV CNTPOFF cpufeature
* for-next/feat_mops:
: Support for ARMv8.8 memcpy instructions in userspace
kselftest/arm64: add MOPS to hwcap test
arm64: mops: allow disabling MOPS from the kernel command line
arm64: mops: detect and enable FEAT_MOPS
arm64: mops: handle single stepping after MOPS exception
arm64: mops: handle MOPS exceptions
KVM: arm64: hide MOPS from guests
arm64: mops: don't disable host MOPS instructions from EL2
arm64: mops: document boot requirements for MOPS
KVM: arm64: switch HCRX_EL2 between host and guest
arm64: cpufeature: detect FEAT_HCX
KVM: arm64: initialize HCRX_EL2
* for-next/module-alloc:
: Make the arm64 module allocation code more robust (clean-up, VA range expansion)
arm64: module: rework module VA range selection
arm64: module: mandate MODULE_PLTS
arm64: module: move module randomization to module.c
arm64: kaslr: split kaslr/module initialization
arm64: kasan: remove !KASAN_VMALLOC remnants
arm64: module: remove old !KASAN_VMALLOC logic
* for-next/sysreg: (21 commits)
: More sysreg conversions to automatic generation
arm64/sysreg: Convert TRBIDR_EL1 register to automatic generation
arm64/sysreg: Convert TRBTRG_EL1 register to automatic generation
arm64/sysreg: Convert TRBMAR_EL1 register to automatic generation
arm64/sysreg: Convert TRBSR_EL1 register to automatic generation
arm64/sysreg: Convert TRBBASER_EL1 register to automatic generation
arm64/sysreg: Convert TRBPTR_EL1 register to automatic generation
arm64/sysreg: Convert TRBLIMITR_EL1 register to automatic generation
arm64/sysreg: Rename TRBIDR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBTRG_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBMAR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBSR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBBASER_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBPTR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBLIMITR_EL1 fields per auto-gen tools format
arm64/sysreg: Convert OSECCR_EL1 to automatic generation
arm64/sysreg: Convert OSDTRTX_EL1 to automatic generation
arm64/sysreg: Convert OSDTRRX_EL1 to automatic generation
arm64/sysreg: Convert OSLAR_EL1 to automatic generation
arm64/sysreg: Standardise naming of bitfield constants in OSL[AS]R_EL1
arm64/sysreg: Convert MDSCR_EL1 to automatic register generation
...
* for-next/cpucap:
: arm64 cpucap clean-up
arm64: cpufeature: fold cpus_set_cap() into update_cpu_capabilities()
arm64: cpufeature: use cpucap naming
arm64: alternatives: use cpucap naming
arm64: standardise cpucap bitmap names
* for-next/acpi:
: Various arm64-related ACPI patches
ACPI: bus: Consolidate all arm specific initialisation into acpi_arm_init()
* for-next/kdump:
: Simplify the crashkernel reservation behaviour of crashkernel=X,high on arm64
arm64: add kdump.rst into index.rst
Documentation: add kdump.rst to present crashkernel reservation on arm64
arm64: kdump: simplify the reservation behaviour of crashkernel=,high
* for-next/acpi-doc:
: Update ACPI documentation for Arm systems
Documentation/arm64: Update ACPI tables from BBR
Documentation/arm64: Update references in arm-acpi
Documentation/arm64: Update ARM and arch reference
* for-next/doc:
: arm64 documentation updates
Documentation/arm64: Add ptdump documentation
* for-next/tpidr2-fix:
: Fix the TPIDR2_EL0 register restoring on sigreturn
kselftest/arm64: Add a test case for TPIDR2 restore
arm64/signal: Restore TPIDR2 register rather than memory state
Don't register a resource for the second page unless the dual-page
extension flag is actually present to say it's valid.
CC: Lorenzo Pieralisi <lpieralisi@kernel.org>
CC: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-and-tested-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/63b34656e1f7b41bcb458fb6d7496e04db757e0d.1685983270.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Move all of the ARM-specific initialization into one function namely
acpi_arm_init(), so it is not necessary to modify/update bus.c every
time a new piece of it is added.
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/CAJZ5v0iBZRZmV_oU+VurqxnVMbFN_ttqrL=cLh0sUH+=u0PYsw@mail.gmail.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Link: https://lore.kernel.org/r/20230606093531.2746732-1-sudeep.holla@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Returning an error value in a platform driver's remove callback results in
a generic error message being emitted by the driver core, but otherwise it
doesn't make a difference. The device goes away anyhow.
So instead of triggering the generic platform error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making platform remove callbacks return
void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20221014160623.467195-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Will Deacon <will@kernel.org>
Add missing kerneldoc and fix alignment on one of the arguments of
apmt_add_platform_device function.
Signed-off-by: Besar Wicaksono <bwicaksono@nvidia.com>
Link: https://lore.kernel.org/r/20221111234323.16182-1-bwicaksono@nvidia.com
[will: Fixed up additional indentation issue]
Signed-off-by: Will Deacon <will@kernel.org>
IORT E.e now allows SMMUv3 nodes to describe the DeviceID for MSIs
independently of wired GSIVs, where the previous oddly-restrictive
definition meant that an SMMU without PRI support had to provide a
DeviceID even if it didn't support MSIs either. Support this, with
the usual temporary flag definition while the real one is making
its way through ACPICA.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/r/4b3e2ead4f392d1a47a7528da119d57918e5d806.1664392886.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
ARM Performance Monitoring Unit Table describes the properties of PMU
support in ARM-based system. The APMT table contains a list of nodes,
each represents a PMU in the system that conforms to ARM CoreSight PMU
architecture. The properties of each node include information required
to access the PMU (e.g. MMIO base address, interrupt number) and also
identification. For more detailed information, please refer to the
specification below:
* APMT: https://developer.arm.com/documentation/den0117/latest
* ARM Coresight PMU:
https://developer.arm.com/documentation/ihi0091/latest
The initial support adds the detection of APMT table and generic
infrastructure to create platform devices for ARM CoreSight PMUs.
Similar to IORT the root pointer of APMT is preserved during runtime
and each PMU platform device is given a pointer to the corresponding
APMT node.
Signed-off-by: Besar Wicaksono <bwicaksono@nvidia.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20220929002834.32664-1-bwicaksono@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Add gfp parameter to iommu_alloc_resv_region() for the callers to specify
the memory allocation behavior. Thus iommu_alloc_resv_region() could also
be available in critical contexts.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20220927053109.4053662-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In DT systems configurations, of_dma_get_range() returns struct
bus_dma_region DMA regions; they are used to set-up devices
DMA windows with different offset available for translation between DMA
address and CPU address.
In ACPI systems configuration, acpi_dma_get_range() does not return
DMA regions yet and that precludes setting up the dev->dma_range_map
pointer and therefore DMA regions with multiple offsets.
Update acpi_dma_get_range() to return struct bus_dma_region
DMA regions like of_dma_get_range() does.
After updating acpi_dma_get_range(), acpi_arch_dma_setup() is changed for
ARM64, where the original dma_addr and size are removed as these
arguments are now redundant, and pass 0 and U64_MAX for dma_base
and size of arch_setup_dma_ops; this is a simplification consistent
with what other ACPI architectures also pass to iommu_setup_dma_ops().
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If CONFIG_ACPI_IORT=y and CONFIG_IOMMU_API is not set,
make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-,
will be failed, like this:
drivers/acpi/arm64/iort.c: In function ‘iort_get_rmr_sids’:
drivers/acpi/arm64/iort.c:1406:2: error: implicit declaration of function ‘iort_iommu_rmr_get_resv_regions’; did you mean ‘iort_iommu_get_resv_regions’? [-Werror=implicit-function-declaration]
iort_iommu_rmr_get_resv_regions(iommu_fwnode, NULL, head);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
iort_iommu_get_resv_regions
cc1: some warnings being treated as errors
make[3]: *** [drivers/acpi/arm64/iort.o] Error 1
The function iort_iommu_rmr_get_resv_regions()
is declared under CONFIG_IOMMU_API,
and the callers of iort_get_rmr_sids() and iort_put_rmr_sids()
would select IOMMU_API.
To fix this error, move the definitions to #ifdef CONFIG_IOMMU_API.
Fixes: e302eea8f4 ("ACPI/IORT: Add a helper to retrieve RMR info directly")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20220726033520.47865-1-renzhijie2@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This will provide a way for SMMU drivers to retrieve StreamIDs
associated with IORT RMR nodes and use that to set bypass settings
for those IDs.
Tested-by: Steven Price <steven.price@arm.com>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220615101044.1972-6-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Parse through the IORT RMR nodes and populate the reserve region list
corresponding to a given IOMMU and device(optional). Also, go through
the ID mappings of the RMR node and retrieve all the SIDs associated
with it.
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Steven Price <steven.price@arm.com>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220615101044.1972-5-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently IORT provides a helper to retrieve HW MSI reserve regions.
Change this to a generic helper to retrieve any IORT related reserve
regions. This will be useful when we add support for RMR nodes in
subsequent patches.
[Lorenzo: For ACPI IORT]
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Steven Price <steven.price@arm.com>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220615101044.1972-4-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
At present iort_iommu_msi_get_resv_regions() returns the number of
MSI reserved regions on success and there are no users for this.
The reserved region list will get populated anyway for platforms
that require the HW MSI region reservation. Hence, change the
function to return void instead.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Steven Price <steven.price@arm.com>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220615101044.1972-3-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When building with W=1, we get the following warning:
drivers/acpi/arm64/agdi.c:88:13: warning: no previous prototype for ‘acpi_agdi_init’ [-Wmissing-prototypes]
void __init acpi_agdi_init(void)
Include AGDI driver's header file to pull in the prototype definition
for acpi_agdi_init() to get rid of the compiler warning
Fixes: a2a591fb76 ("ACPI: AGDI: Add driver for Arm Generic Diagnostic Dump and Reset device")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI for Arm Components 1.1 Platform Design Document v1.1 [0] specifices
Arm Generic Diagnostic Device Interface (AGDI). It allows an admin to
issue diagnostic dump and reset via an SDEI event or an interrupt.
This patch implements SDEI path.
[0] https://developer.arm.com/documentation/den0093/latest/
Signed-off-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The original version of the IORT PMCG definition had an oversight
wherein there was no way to describe the second register page for an
implementation using the recommended RELOC_CTRS feature. Although the
spec was fixed, and the final patches merged to ACPICA and Linux written
against the new version, it seems that some old firmware based on the
original revision has survived and turned up in the wild.
Add a check for the original PMCG definition, and avoid filling in the
second memory resource with nonsense if so. Otherwise it is likely that
something horrible will happen when the PMCG driver attempts to probe.
Reported-by: Michael Petlan <mpetlan@redhat.com>
Fixes: 24e5160493 ("ACPI/IORT: Add support for PMCG")
Cc: <stable@vger.kernel.org> # 5.2.x
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/75628ae41c257fb73588f7bf1c4459160e04be2b.1643916258.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix modpost Section mismatch error in next_platform_timer().
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
make[1]: *** [scripts/Makefile.modpost:59: vmlinux.symvers] Error 1
make[1]: *** Deleting file 'vmlinux.symvers'
make: *** [Makefile:1176: vmlinux] Error 2
[...]
Fixes: a712c3ed9b ("acpi/arm64: Add memory-mapped timer support in GTDT driver")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20210823092526.2407526-1-liu.yun@linux.dev
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Including:
- SMMU Updates from Will Deacon:
- SMMUv3: Support stalling faults for platform devices
- SMMUv3: Decrease defaults sizes for the event and PRI queues
- SMMUv2: Support for a new '->probe_finalize' hook, needed by Nvidia
- SMMUv2: Even more Qualcomm compatible strings
- SMMUv2: Avoid Adreno TTBR1 quirk for DB820C platform
- Intel VT-d updates from Lu Baolu:
- Convert Intel IOMMU to use sva_lib helpers in iommu core
- ftrace and debugfs supports for page fault handling
- Support asynchronous nested capabilities
- Various misc cleanups
- Support for new VIOT ACPI table to make the VirtIO IOMMU:
available on x86
- Add the amd_iommu=force_enable command line option to
enable the IOMMU on platforms where they are known to cause
problems
- Support for version 2 of the Rockchip IOMMU
- Various smaller fixes, cleanups and refactorings
-----BEGIN PGP SIGNATURE-----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=IxNB
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- SMMU Updates from Will Deacon:
- SMMUv3:
- Support stalling faults for platform devices
- Decrease defaults sizes for the event and PRI queues
- SMMUv2:
- Support for a new '->probe_finalize' hook, needed by Nvidia
- Even more Qualcomm compatible strings
- Avoid Adreno TTBR1 quirk for DB820C platform
- Intel VT-d updates from Lu Baolu:
- Convert Intel IOMMU to use sva_lib helpers in iommu core
- ftrace and debugfs supports for page fault handling
- Support asynchronous nested capabilities
- Various misc cleanups
- Support for new VIOT ACPI table to make the VirtIO IOMMU
available on x86
- Add the amd_iommu=force_enable command line option to enable
the IOMMU on platforms where they are known to cause problems
- Support for version 2 of the Rockchip IOMMU
- Various smaller fixes, cleanups and refactorings
* tag 'iommu-updates-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (66 commits)
iommu/virtio: Enable x86 support
iommu/dma: Pass address limit rather than size to iommu_setup_dma_ops()
ACPI: Add driver for the VIOT table
ACPI: Move IOMMU setup code out of IORT
ACPI: arm64: Move DMA setup operations out of IORT
iommu/vt-d: Fix dereference of pointer info before it is null checked
iommu: Update "iommu.strict" documentation
iommu/arm-smmu: Check smmu->impl pointer before dereferencing
iommu/arm-smmu-v3: Remove unnecessary oom message
iommu/arm-smmu: Fix arm_smmu_device refcount leak in address translation
iommu/arm-smmu: Fix arm_smmu_device refcount leak when arm_smmu_rpm_get fails
iommu/vt-d: Fix linker error on 32-bit
iommu/vt-d: No need to typecast
iommu/vt-d: Define counter explicitly as unsigned int
iommu/vt-d: Remove unnecessary braces
iommu/vt-d: Removed unused iommu_count in dmar domain
iommu/vt-d: Use bitfields for DMAR capabilities
iommu/vt-d: Use DEVICE_ATTR_RO macro
iommu/vt-d: Fix out-bounds-warning in intel/svm.c
iommu/vt-d: Add PRQ handling latency sampling
...
Extract the code that sets up the IOMMU infrastructure from IORT, since
it can be reused by VIOT. Move it one level up into a new
acpi_iommu_configure_id() function, which calls the IORT parsing
function which in turn calls the acpi_iommu_fwspec_init() helper.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210618152059.1194210-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Extract generic DMA setup code out of IORT, so it can be reused by VIOT.
Keep it in drivers/acpi/arm64 for now, since it could break x86
platforms that haven't run this code so far, if they have invalid
tables.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210618152059.1194210-2-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Copy the "Stall supported" bit, that tells whether a named component
supports stall, into the dma-can-stall device property.
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210526161927.24268-3-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
The older device property API is going to be removed.
Replacing the device_add_properties() call with software
node API equivalent device_create_managed_software_node().
Fixes: 434b73e61c ("iommu/arm-smmu-v3: Use device properties for pasid-num-bits")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Restore terminal stack frame records. Their previous removal caused
traces which cross secondary_start_kernel to terminate one entry too
late, with a spurious "0" entry.
- Fix boot warning with pseudo-NMI due to the way we manipulate the PMR
register.
- ACPI fixes: avoid corruption of interrupt mappings on watchdog probe
failure (GTDT), prevent unregistering of GIC SGIs.
- Force SPARSEMEM_VMEMMAP as the only memory model, it saves with having
to test all the other combinations.
- Documentation fixes and updates: tagged address ABI exceptions on
brk/mmap/mremap(), event stream frequency, update booting requirements
on the configuration of traps.
-----BEGIN PGP SIGNATURE-----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=vYok
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
"A mix of fixes and clean-ups that turned up too late for the first
pull request:
- Restore terminal stack frame records. Their previous removal caused
traces which cross secondary_start_kernel to terminate one entry
too late, with a spurious "0" entry.
- Fix boot warning with pseudo-NMI due to the way we manipulate the
PMR register.
- ACPI fixes: avoid corruption of interrupt mappings on watchdog
probe failure (GTDT), prevent unregistering of GIC SGIs.
- Force SPARSEMEM_VMEMMAP as the only memory model, it saves with
having to test all the other combinations.
- Documentation fixes and updates: tagged address ABI exceptions on
brk/mmap/mremap(), event stream frequency, update booting
requirements on the configuration of traps"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kernel: Update the stale comment
arm64: Fix the documented event stream frequency
arm64: entry: always set GIC_PRIO_PSR_I_SET during entry
arm64: Explicitly document boot requirements for SVE
arm64: Explicitly require that FPSIMD instructions do not trap
arm64: Relax booting requirements for configuration of traps
arm64: cpufeatures: use min and max
arm64: stacktrace: restore terminal records
arm64/vdso: Discard .note.gnu.property sections in vDSO
arm64: doc: Add brk/mmap/mremap() to the Tagged Address ABI Exceptions
psci: Remove unneeded semicolon
ACPI: irq: Prevent unregistering of GIC SGIs
ACPI: GTDT: Don't corrupt interrupt mappings on watchdow probe failure
arm64: Show three registers per line
arm64: remove HAVE_DEBUG_BUGVERBOSE
arm64: alternative: simplify passing alt_region
arm64: Force SPARSEMEM_VMEMMAP as the only memory management model
arm64: vdso32: drop -no-integrated-as flag
When failing the driver probe because of invalid firmware properties,
the GTDT driver unmaps the interrupt that it mapped earlier.
However, it never checks whether the mapping of the interrupt actially
succeeded. Even more, should the firmware report an illegal interrupt
number that overlaps with the GIC SGI range, this can result in an
IPI being unmapped, and subsequent fireworks (as reported by Dann
Frazier).
Rework the driver to have a slightly saner behaviour and actually
check whether the interrupt has been mapped before unmapping things.
Reported-by: dann frazier <dann.frazier@canonical.com>
Fixes: ca9ae5ec4e ("acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/YH87dtTfwYgavusz@xps13.dannf
Cc: <stable@vger.kernel.org>
Cc: Fu Wei <wefu@redhat.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20210421164317.1718831-2-maz@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The pasid-num-bits property shouldn't need a dedicated fwspec field,
it's a job for device properties. Add properties for IORT, and access
the number of PASID bits using device_property_read_u32().
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20210401154718.307519-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Address issue observed on real world system with suboptimal IORT table
where DMA masks of PCI devices would get set to 0 as result.
iort_dma_setup() would query the root complex'/named component IORT
entry for a DMA mask, and use that over the one the device has been
configured with earlier.
Ideally we want to use the minimum mask of what the IORT contains for
the root complex and what the device was configured with.
Fixes: 5ac65e8c89 ("ACPI/IORT: Support address size limit for root complexes")
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20210122012419.95010-1-mdf@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix following warnings caused by mismatch between
function parameters and function comments.
drivers/acpi/arm64/iort.c:55: warning: Function parameter or member 'iort_node' not described in 'iort_set_fwnode'
drivers/acpi/arm64/iort.c:55: warning: Excess function parameter 'node' description in 'iort_set_fwnode'
drivers/acpi/arm64/iort.c:682: warning: Function parameter or member 'id' not described in 'iort_get_device_domain'
drivers/acpi/arm64/iort.c:682: warning: Function parameter or member 'bus_token' not described in 'iort_get_device_domain'
drivers/acpi/arm64/iort.c:682: warning: Excess function parameter 'req_id' description in 'iort_get_device_domain'
drivers/acpi/arm64/iort.c:1142: warning: Function parameter or member 'dma_size' not described in 'iort_dma_setup'
drivers/acpi/arm64/iort.c:1142: warning: Excess function parameter 'size' description in 'iort_dma_setup'
drivers/acpi/arm64/iort.c:1534: warning: Function parameter or member 'ops' not described in 'iort_add_platform_device'
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20201014093139.1580-1-shiju.jose@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
Instructing the DMA layer about these limitations is straight-forward,
even though we had to fix some issues regarding memory limits set in
the IORT for named components, and regarding the handling of ACPI _DMA
methods. However, the DMA layer also needs to be able to allocate
memory that is guaranteed to meet those DMA constraints, for bounce
buffering as well as allocating the backing for consistent mappings.
This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately,
it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes
problems with kdump, and potentially in other places where allocations
cannot cross zone boundaries. Therefore, we should avoid having two
separate DMA zones when possible.
So let's do an early scan of the IORT, and only create the ZONE_DMA
if we encounter any devices that need it. This puts the burden on
the firmware to describe such limitations in the IORT, which may be
redundant (and less precise) if _DMA methods are also being provided.
However, it should be noted that this situation is highly unusual for
arm64 ACPI machines. Also, the DMA subsystem still gives precedence to
the _DMA method if implemented, and so we will not lose the ability to
perform streaming DMA outside the ZONE_DMA if the _DMA method permits
it.
[nsaenz: unified implementation with DT's counterpart]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-7-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
- Add support for generic initiator-only proximity domains to
the ACPI NUMA code and the architectures using it (Jonathan
Cameron).
- Clean up some non-ACPICA code referring to debug facilities from
ACPICA that are not actually used in there (Hanjun Guo).
- Add new DPTF driver for the PCH FIVR participant (Srinivas
Pandruvada).
- Reduce overhead related to accessing GPE registers in ACPICA and
the OS interface layer and make it possible to access GPE registers
using logical addresses if they are memory-mapped (Rafael Wysocki).
- Update the ACPICA code in the kernel to upstream revision 20200925
including changes as follows:
* Add predefined names from the SMBus sepcification (Bob Moore).
* Update acpi_help UUID list (Bob Moore).
* Return exceptions for string-to-integer conversions in iASL (Bob
Moore).
* Add a new "ALL <NameSeg>" debugger command (Bob Moore).
* Add support for 64 bit risc-v compilation (Colin Ian King).
* Do assorted cleanups (Bob Moore, Colin Ian King, Randy Dunlap).
- Add new ACPI backlight whitelist entry for HP 635 Notebook (Alex
Hung).
- Move TPS68470 OpRegion driver to drivers/acpi/pmic/ and split out
Kconfig and Makefile specific for ACPI PMIC (Andy Shevchenko).
- Clean up the ACPI SoC driver for AMD SoCs (Hanjun Guo).
- Add missing config_item_put() to fix refcount leak (Hanjun Guo).
- Drop lefrover field from struct acpi_memory_device (Hanjun Guo).
- Make the ACPI extlog driver check for RDMSR failures (Ben
Hutchings).
- Fix handling of lid state changes in the ACPI button driver when
input device is closed (Dmitry Torokhov).
- Fix several assorted build issues (Barnabás Pőcze, John Garry,
Nathan Chancellor, Tian Tao).
- Drop unused inline functions and reduce code duplication by using
kobj_to_dev() in the NFIT parsing code (YueHaibing, Wang Qing).
- Serialize tools/power/acpi Makefile (Thomas Renninger).
-----BEGIN PGP SIGNATURE-----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=feLU
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These add support for generic initiator-only proximity domains to the
ACPI NUMA code and the architectures using it, clean up some
non-ACPICA code referring to debug facilities from ACPICA, reduce the
overhead related to accessing GPE registers, add a new DPTF (Dynamic
Power and Thermal Framework) participant driver, update the ACPICA
code in the kernel to upstream revision 20200925, add a new ACPI
backlight whitelist entry, fix a few assorted issues and clean up some
code.
Specifics:
- Add support for generic initiator-only proximity domains to the
ACPI NUMA code and the architectures using it (Jonathan Cameron)
- Clean up some non-ACPICA code referring to debug facilities from
ACPICA that are not actually used in there (Hanjun Guo)
- Add new DPTF driver for the PCH FIVR participant (Srinivas
Pandruvada)
- Reduce overhead related to accessing GPE registers in ACPICA and
the OS interface layer and make it possible to access GPE registers
using logical addresses if they are memory-mapped (Rafael Wysocki)
- Update the ACPICA code in the kernel to upstream revision 20200925
including changes as follows:
+ Add predefined names from the SMBus sepcification (Bob Moore)
+ Update acpi_help UUID list (Bob Moore)
+ Return exceptions for string-to-integer conversions in iASL (Bob
Moore)
+ Add a new "ALL <NameSeg>" debugger command (Bob Moore)
+ Add support for 64 bit risc-v compilation (Colin Ian King)
+ Do assorted cleanups (Bob Moore, Colin Ian King, Randy Dunlap)
- Add new ACPI backlight whitelist entry for HP 635 Notebook (Alex
Hung)
- Move TPS68470 OpRegion driver to drivers/acpi/pmic/ and split out
Kconfig and Makefile specific for ACPI PMIC (Andy Shevchenko)
- Clean up the ACPI SoC driver for AMD SoCs (Hanjun Guo)
- Add missing config_item_put() to fix refcount leak (Hanjun Guo)
- Drop lefrover field from struct acpi_memory_device (Hanjun Guo)
- Make the ACPI extlog driver check for RDMSR failures (Ben
Hutchings)
- Fix handling of lid state changes in the ACPI button driver when
input device is closed (Dmitry Torokhov)
- Fix several assorted build issues (Barnabás Pőcze, John Garry,
Nathan Chancellor, Tian Tao)
- Drop unused inline functions and reduce code duplication by using
kobj_to_dev() in the NFIT parsing code (YueHaibing, Wang Qing)
- Serialize tools/power/acpi Makefile (Thomas Renninger)"
* tag 'acpi-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPICA: Update version to 20200925 Version 20200925
ACPICA: Remove unnecessary semicolon
ACPICA: Debugger: Add a new command: "ALL <NameSeg>"
ACPICA: iASL: Return exceptions for string-to-integer conversions
ACPICA: acpi_help: Update UUID list
ACPICA: Add predefined names found in the SMBus sepcification
ACPICA: Tree-wide: fix various typos and spelling mistakes
ACPICA: Drop the repeated word "an" in a comment
ACPICA: Add support for 64 bit risc-v compilation
ACPI: button: fix handling lid state changes when input device closed
tools/power/acpi: Serialize Makefile
ACPI: scan: Replace ACPI_DEBUG_PRINT() with pr_debug()
ACPI: memhotplug: Remove 'state' from struct acpi_memory_device
ACPI / extlog: Check for RDMSR failure
ACPI: Make acpi_evaluate_dsm() prototype consistent
docs: mm: numaperf.rst Add brief description for access class 1.
node: Add access1 class to represent CPU to memory characteristics
ACPI: HMAT: Fix handling of changes from ACPI 6.2 to ACPI 6.3
ACPI: Let ACPI know we support Generic Initiator Affinity Structures
x86: Support Generic Initiator only proximity domains
...
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Several ACPI static tables contain references to proximity domains.
ACPI 6.3 has clarified that only entries in SRAT may define a new
domain (sec 5.2.16).
Those tables described in the ACPI spec have additional clarifying text.
NFIT: Table 5-132,
"Integer that represents the proximity domain to which the memory
belongs. This number must match with corresponding entry in the
SRAT table."
HMAT: Table 5-145,
"... This number must match with the corresponding entry in the SRAT
table's processor affinity structure ... if the initiator is a processor,
or the Generic Initiator Affinity Structure if the initiator is a generic
initiator".
IORT and DMAR are defined by external specifications.
Intel Virtualization Technology for Directed I/O Rev 3.1 does not make any
explicit statements, but the general SRAT statement above will still apply.
https://software.intel.com/sites/default/files/managed/c5/15/vt-directed-io-spec.pdf
IO Remapping Table, Platform Design Document rev D, also makes not explicit
statement, but refers to ACPI SRAT table for more information and again the
generic SRAT statement above applies.
https://developer.arm.com/documentation/den0049/d/
In conclusion, any proximity domain specified in these tables, should be a
reference to a proximity domain also found in SRAT, and they should not be
able to instantiate a new domain. Hence we switch to pxm_to_node() which
will only return existing nodes.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Since commit 8212688600 ("ACPI/IORT: Fix build error when IOMMU_SUPPORT
is disabled"), iort_fwspec_iommu_ops() and iort_add_device_replay() are not
needed anymore when CONFIG_IOMMU_API is not selected. Let's remove them.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20200818063625.980-3-yuzenghui@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Since commit d2e1a003af ("ACPI/IORT: Don't call iommu_ops->add_device
directly"), we use the IOMMU core API to replace a direct invoke of the
specified callback. The parameter @ops has therefore became unused. Let's
drop it.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20200818063625.980-2-yuzenghui@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Some HW devices are created as child devices of proprietary busses,
that have a bus specific policy defining how the child devices
wires representing the devices ID are translated into IOMMU and
IRQ controllers device IDs.
Current IORT code provides translations for:
- PCI devices, where the device ID is well identified at bus level
as the requester ID (RID)
- Platform devices that are endpoint devices where the device ID is
retrieved from the ACPI object IORT mappings (Named components single
mappings). A platform device is represented in IORT as a named
component node
For devices that are child devices of proprietary busses the IORT
firmware represents the bus node as a named component node in IORT
and it is up to that named component node to define in/out bus
specific ID translations for the bus child devices that are
allocated and created in a bus specific manner.
In order to make IORT ID translations available for proprietary
bus child devices, the current ACPI (and IORT) code must be
augmented to provide an additional ID parameter to acpi_dma_configure()
representing the child devices input ID. This ID is bus specific
and it is retrieved in bus specific code.
By adding an ID parameter to acpi_dma_configure(), the IORT
code can map the child device ID to an IOMMU stream ID through
the IORT named component representing the bus in/out ID mappings.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-6-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The PCI bus domain number (used in the iort_match_node_callback() -
pci_domain_nr() call) is cascaded through the PCI bus hierarchy at PCI
bus enumeration time, therefore there is no need in iort_find_dev_node()
to walk the PCI bus upwards to grab the root bus to be passed to
iort_scan_node(), the device->bus PCI bus pointer will do.
Remove this useless code.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-5-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is nothing PCI specific in iort_msi_map_rid().
Rename the function using a bus protocol agnostic name,
iort_msi_map_id(), and convert current callers to it.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-4-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
iort_get_device_domain() is PCI specific but it need not be,
since it can be used to retrieve IRQ domain nexus of any kind
by adding an irq_domain_bus_token input to it.
Make it PCI agnostic by also renaming the requestor ID input
to a more generic ID name.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci/msi.c
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-3-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When the iort_match_node_callback is invoked for a named component
the match should be executed upon a device with an ACPI companion.
For devices with no ACPI companion set-up the ACPI device tree must be
walked in order to find the first parent node with a companion set and
check the parent node against the named component entry to check whether
there is a match and therefore an IORT node describing the in/out ID
translation for the device has been found.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-2-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since commit bc8648d49a ("ACPI/IORT: Handle PCI aliases properly for
IOMMUs"), __get_pci_rid() has become actually unused and can be removed.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20200509093430.1983-1-yuzenghui@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
An IORT PMCG node can have no ID mapping if its overflow interrupt is
wire based therefore the code that parses the PMCG node can not assume
the node will always have a single mapping present at index 0.
Fix iort_get_id_mapping_index() by checking for an overflow interrupt
and mapping count.
Fixes: 24e5160493 ("ACPI/IORT: Add support for PMCG")
Signed-off-by: Tuan Phan <tuanphan@os.amperecomputing.com>
Reviewed-by: Hanjun Guo <guoahanjun@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/1589994787-28637-1-git-send-email-tuanphan@os.amperecomputing.com
Signed-off-by: Will Deacon <will@kernel.org>
As we already applied a workaround for the off-by-1 issue,
it's good to add extra message "applying workaround" to make
people less uneasy to see FW_BUG message in the boot log.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/1588910198-8348-1-git-send-email-guohanjun@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
The ID mapping table structure of the IORT table describes the size of
a range using a num_ids field carrying the number of IDs in the region
minus one. This has been misinterpreted in the past in the parsing code,
and firmware is known to have shipped where this results in an ambiguity,
where regions that should be adjacent have an overlap of one value.
So let's work around this by detecting this case specifically: when
resolving an ID translation, allow one that matches right at the end of
a multi-ID region to be superseded by a subsequent one.
To prevent potential regressions on broken firmware that happened to
work before, only take the subsequent match into account if it occurs
at the start of a mapping region.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20200501161014.5935-3-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Catalin Marinas