Convert QPRINTK macros to netif_<level> equivalents.
Expands and standardizes the logging message output.
Removes __func__ from most logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add periodic heartbeat register read to trigger the eeh
recovery process.
We see cases where an eeh error was injected and the slot was
suspended. An asic access attempt is required to flush the recovery process,
but without interrupts the process can stall.
Adding this periodic register read causes the recovery process to begin.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix crash where resources are freed twice on an eeh recovery failure.
If eeh recovery fails we set a flag to indicate to close() that
resources have been freed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default setting is 'off', don't allow force firmware dump.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the infrstructure and basic data for the firmware
core dump.
The firmware coredump is turned OFF by default. There will be no
memory allocations for data dumps to the log.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using 4-byte aligned headers is problematic for some architectures.
Since qlge uses 4-byte aligned rx buffers we split headers for these
architectures into a separate buffer and then recopy to align on 2-byte boundary.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't access netdev->stats in IO path. Save them in tx_ring/rx_rings
and add them up when get_stats API is called.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These sub-commands are issued by another (FCoE) function requesting
an operation on a shared resource.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change RX large buffer size based on MTU. If pages are larger
than the MTU the page is divided up into multiple chunks and passed to
the hardware. When pages are smaller than MTU each RX buffer can
contain be comprised of up to 2 pages.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ring->sbq_buf_len now holds the length of the mapped portion of the
buffer rather than the overall length.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wait for NIC fifo and MGMNT fifo to empty before applying reset.
Otherwise broken frames can be processed by management processor and
cause it to hang.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix RX queue table size and change from random to default hash values.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of spinlock and private mutex usage for exclusive access to the
HW semaphore register. rtnl_lock already creates exclusive access to
this register in all driver API.
Add rtnl to firmware worker threads that also use the HW semaphore register.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX completions were running in a workqueue queued by the ISR. This
patch moves the processing of TX completions to an existing RSS NAPI
context.
Now each irq vector runs NAPI for one RSS ring and one or more TX
completion rings.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have three types of RX rings.
1) Default ring - services rx_ring for broadcast/multicast, handles
firmware events, and errors.
2) TX completion ring - handles only outbound completions.
3) RSS ring - handles only inbound completions.
This patch gets rid of the default ring type and moves it's functionality
into the first RSS ring. This makes better use of MSIX vectors since
they are a limited resource on some platforms.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set/clear the mac address register when the link goes up/down
respectively. Without this both ports of a 2-port device can end up
with the same mac address in a bonding scenario.
The new ql_link_on() and ql_link_off() will also be used in handling
certain firmware events.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX buffer rings can be comprised of non-contiguous fixed
size chunks of memory. The ring is given to the hardware
as a pointer to a location that stores the location of
the queue. If the queue is greater than 4096 bytes then
the hardware gets a list of said pointers.
This patch addes the necessary logic to generate the list if
the queue size exceeds 4096.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alignment was on size of queue boundary, but the hardware
only requires 4-byte alignment.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support only PCIe NIC functions zero and one, and FCoE
functions as 3 and 4. Future configurations can mix these up in any
fashion.
This patch removes the 0-1 dependancy and allows usage of any of the 4
functions. We also find the alternate NIC function (if exist) and
determine our port number based on the comparison of the two functions:
Lower function number gets first port, higher function gets second port.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 8 banks of 'sub-registers' each of which are accessed
through address/data register pair. An example would be reading
flash or the xgmac. Accessing these require the driver to wait for
a ready bit before writing the address and then accessing the data.
This patch increases the timeout to 100us to prevent timeouts
that have been seen on some platforms.
These register are accessed in process context only.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This organizes a few calls into a function table to enable adding new
devices.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not a logical change but rather a move of the inbound firmware event
handler into it's own function as it will later be called by the outbound
path.
The addition of the mutex is to create exclusive access to the mailbox
commands between inbound and outbound handling.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for dev id 8000 is pushed out until 2.6.30.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Putting back ql_read_sh_reg() function and using rmb() instead of
volatile.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warnings:
drivers/net/qlge/qlge_main.c:1474:34: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1475:36: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1592:51: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1941:20: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:1941:20: expected restricted unsigned int [usertype] tid
drivers/net/qlge/qlge_main.c:1941:20: got int [signed] index
drivers/net/qlge/qlge_main.c:1945:24: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:1945:24: expected restricted unsigned int [usertype] txq_idx
drivers/net/qlge/qlge_main.c:1945:24: got unsigned int [unsigned] [usertype] tx_ring_idx
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warnings:
drivers/net/qlge/qlge_main.c:909:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:909:17: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:909:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:911:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:911:17: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:911:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:974:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:974:17: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:974:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:975:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:975:17: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:975:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2132:16: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2132:16: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:2132:16: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2133:16: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2133:16: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:2133:16: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2212:15: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2212:15: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:2212:15: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2214:15: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2214:15: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:2214:15: got restricted unsigned int [usertype] <noident>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
