With the last non-OF, non-ACPI user of the GIC being removed in
e73307b9eb ("ARM: cns3xxx: remove entire platform"), we can finally
drop the entry point and do some minor cleanup.
We also make the driver depend on CONFIG_OF, which is required
even when CONFIG_ACPI is selected.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230315130218.3212033-1-maz@kernel.org
- Support for arm64 SME 2 and 2.1. SME2 introduces a new 512-bit
architectural register (ZT0, for the look-up table feature) that Linux
needs to save/restore.
- Include TPIDR2 in the signal context and add the corresponding
kselftests.
- Perf updates: Arm SPEv1.2 support, HiSilicon uncore PMU updates, ACPI
support to the Marvell DDR and TAD PMU drivers, reset DTM_PMU_CONFIG
(ARM CMN) at probe time.
- Support for DYNAMIC_FTRACE_WITH_CALL_OPS on arm64.
- Permit EFI boot with MMU and caches on. Instead of cleaning the entire
loaded kernel image to the PoC and disabling the MMU and caches before
branching to the kernel bare metal entry point, leave the MMU and
caches enabled and rely on EFI's cacheable 1:1 mapping of all of
system RAM to populate the initial page tables.
- Expose the AArch32 (compat) ELF_HWCAP features to user in an arm64
kernel (the arm32 kernel only defines the values).
- Harden the arm64 shadow call stack pointer handling: stash the shadow
stack pointer in the task struct on interrupt, load it directly from
this structure.
- Signal handling cleanups to remove redundant validation of size
information and avoid reading the same data from userspace twice.
- Refactor the hwcap macros to make use of the automatically generated
ID registers. It should make new hwcaps writing less error prone.
- Further arm64 sysreg conversion and some fixes.
- arm64 kselftest fixes and improvements.
- Pointer authentication cleanups: don't sign leaf functions, unify
asm-arch manipulation.
- Pseudo-NMI code generation optimisations.
- Minor fixes for SME and TPIDR2 handling.
- Miscellaneous updates: ARCH_FORCE_MAX_ORDER is now selectable, replace
strtobool() to kstrtobool() in the cpufeature.c code, apply dynamic
shadow call stack in two passes, intercept pfn changes in set_pte_at()
without the required break-before-make sequence, attempt to dump all
instructions on unhandled kernel faults.
-----BEGIN PGP SIGNATURE-----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=VmXL
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Support for arm64 SME 2 and 2.1. SME2 introduces a new 512-bit
architectural register (ZT0, for the look-up table feature) that
Linux needs to save/restore
- Include TPIDR2 in the signal context and add the corresponding
kselftests
- Perf updates: Arm SPEv1.2 support, HiSilicon uncore PMU updates, ACPI
support to the Marvell DDR and TAD PMU drivers, reset DTM_PMU_CONFIG
(ARM CMN) at probe time
- Support for DYNAMIC_FTRACE_WITH_CALL_OPS on arm64
- Permit EFI boot with MMU and caches on. Instead of cleaning the
entire loaded kernel image to the PoC and disabling the MMU and
caches before branching to the kernel bare metal entry point, leave
the MMU and caches enabled and rely on EFI's cacheable 1:1 mapping of
all of system RAM to populate the initial page tables
- Expose the AArch32 (compat) ELF_HWCAP features to user in an arm64
kernel (the arm32 kernel only defines the values)
- Harden the arm64 shadow call stack pointer handling: stash the shadow
stack pointer in the task struct on interrupt, load it directly from
this structure
- Signal handling cleanups to remove redundant validation of size
information and avoid reading the same data from userspace twice
- Refactor the hwcap macros to make use of the automatically generated
ID registers. It should make new hwcaps writing less error prone
- Further arm64 sysreg conversion and some fixes
- arm64 kselftest fixes and improvements
- Pointer authentication cleanups: don't sign leaf functions, unify
asm-arch manipulation
- Pseudo-NMI code generation optimisations
- Minor fixes for SME and TPIDR2 handling
- Miscellaneous updates: ARCH_FORCE_MAX_ORDER is now selectable,
replace strtobool() to kstrtobool() in the cpufeature.c code, apply
dynamic shadow call stack in two passes, intercept pfn changes in
set_pte_at() without the required break-before-make sequence, attempt
to dump all instructions on unhandled kernel faults
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (130 commits)
arm64: fix .idmap.text assertion for large kernels
kselftest/arm64: Don't require FA64 for streaming SVE+ZA tests
kselftest/arm64: Copy whole EXTRA context
arm64: kprobes: Drop ID map text from kprobes blacklist
perf: arm_spe: Print the version of SPE detected
perf: arm_spe: Add support for SPEv1.2 inverted event filtering
perf: Add perf_event_attr::config3
arm64/sme: Fix __finalise_el2 SMEver check
drivers/perf: fsl_imx8_ddr_perf: Remove set-but-not-used variable
arm64/signal: Only read new data when parsing the ZT context
arm64/signal: Only read new data when parsing the ZA context
arm64/signal: Only read new data when parsing the SVE context
arm64/signal: Avoid rereading context frame sizes
arm64/signal: Make interface for restore_fpsimd_context() consistent
arm64/signal: Remove redundant size validation from parse_user_sigframe()
arm64/signal: Don't redundantly verify FPSIMD magic
arm64/cpufeature: Use helper macros to specify hwcaps
arm64/cpufeature: Always use symbolic name for feature value in hwcaps
arm64/sysreg: Initial unsigned annotations for ID registers
arm64/sysreg: Initial annotation of signed ID registers
...
Subsequent patches will add more GIC-related cpucaps. When we do so, it
would be nice to give them a consistent HAS_GIC_* prefix.
In preparation for doing so, this patch renames the existing
ARM64_HAS_SYSREG_GIC_CPUIF cap to ARM64_HAS_GIC_CPUIF_SYSREGS.
The 'CPUIF_SYSREGS' suffix is chosen so that this will be ordered ahead
of other ARM64_HAS_GIC_* definitions in subsequent patches.
The cpucaps file was hand-modified; all other changes were scripted
with:
find . -type f -name '*.[chS]' -print0 | \
xargs -0 sed -i
's/ARM64_HAS_SYSREG_GIC_CPUIF/ARM64_HAS_GIC_CPUIF_SYSREGS/'
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20230130145429.903791-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Use the irq_domain_alloc_irqs() wrapper instead of the full
__irq_domain_alloc_irqs() interface, which was only intended for some
legacy (x86) use cases.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20221213140844.15470-2-johan+linaro@kernel.org
- More APCI fixes and improvements for the LoongArch architecture,
adding support for the HTVEC irqchip, suspend-resume, and some
PCI INTx workarounds
- Initial DT support for LoongArch. I'm not even kidding.
- Support for the MTK CIRQv2, a minor deviation from the original version
- Error handling fixes for wpcm450, GIC...
- BE detection for a FSL controller
- Declare the Sifive PLIC as wake-up agnostic
- Simplify fishing out the device data for the ST irqchip
- Mark some data structures as __initconst in the apple-aic driver
- Switch over from strtobool to kstrtobool
- COMPILE_TEST fixes
-----BEGIN PGP SIGNATURE-----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=fhi8
-----END PGP SIGNATURE-----
Merge tag 'irqchip-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates frim Marc Zyngier:
- More APCI fixes and improvements for the LoongArch architecture,
adding support for the HTVEC irqchip, suspend-resume, and some
PCI INTx workarounds
- Initial DT support for LoongArch. I'm not even kidding.
- Support for the MTK CIRQv2, a minor deviation from the original version
- Error handling fixes for wpcm450, GIC...
- BE detection for a FSL controller
- Declare the Sifive PLIC as wake-up agnostic
- Simplify fishing out the device data for the ST irqchip
- Mark some data structures as __initconst in the apple-aic driver
- Switch over from strtobool to kstrtobool
- COMPILE_TEST fixes
irq_domain::dev is a misnomer as it's usually the rule that a device
pointer points to something which is directly related to the instance.
irq_domain::dev can point to some other device for power management to
ensure that this underlying device is not powered down when an interrupt is
allocated.
The upcoming per device MSI domains really require a pointer to the device
which instantiated the irq domain and not to some random other device which
is required for power management down the chain.
Rename irq_domain::dev to irq_domain::pm_dev and fixup the few sites which
use that pointer.
Conversion was done with the help of coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124230313.574541683@linutronix.de
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/755c4083122071bb27aa8ed5d98156a07bb63a39.1667336095.git.christophe.jaillet@wanadoo.fr
In an unfortunate departure from the ACPI spec, the LoongArch
architecture split its GSI space across multiple interrupt
controllers.
In order to be able to reuse the core code and prevent
architectures from reinventing an already square wheel, offer
the arch code the ability to register a dispatcher function
that will return the domain fwnode for a given GSI.
The ARM GIC drivers are updated to support this (with a single
domain, as intended).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/1658314292-35346-3-git-send-email-lvjianmin@loongson.cn
Issue the warning for interrupt lines that have an incorrect interrupt
type and also print the hardware interrupt number to facilitate the
resolution of such problems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220308201117.3870678-1-f.fainelli@gmail.com
At the moment the GIC IRQ domain translation routine happily converts
ACPI table GSI numbers below 16 to GIC SGIs (Software Generated
Interrupts aka IPIs). On the Devicetree side we explicitly forbid this
translation, actually the function will never return HWIRQs below 16 when
using a DT based domain translation.
We expect SGIs to be handled in the first part of the function, and any
further occurrence should be treated as a firmware bug, so add a check
and print to report this explicitly and avoid lengthy debug sessions.
Fixes: 64b499d8df ("irqchip/gic-v3: Configure SGIs as standard interrupts")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220404110842.2882446-1-andre.przywara@arm.com
The last dynamic aspect of the GIC's irq_chip structure is the
name that is associated to it.
Move the output of that name to the relevant callback, which
allows us to do a bit of cleanup and mark the structures const.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-4-maz@kernel.org
Move the reference to the GIC device over to the irq domain.
This allows for some localised cleanup.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-3-maz@kernel.org
Now that entry code handles IRQ entry (including setting the IRQ regs)
before calling irqchip code, irqchip code can safely call
generic_handle_domain_irq(), and there's no functional reason for it to
call handle_domain_irq().
Let's cement this split of responsibility and remove handle_domain_irq()
entirely, updating irqchip drivers to call generic_handle_domain_irq().
For consistency, handle_domain_nmi() is similarly removed and replaced
with a generic_handle_domain_nmi() function which also does not perform
any entry logic.
Previously handle_domain_{irq,nmi}() had a WARN_ON() which would fire
when they were called in an inappropriate context. So that we can
identify similar issues going forward, similar WARN_ON_ONCE() logic is
added to the generic_handle_*() functions, and comments are updated for
clarity and consistency.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Geert reported that the GIC driver locks up on a Renesas system
since 005c34ae4b ("irqchip/gic: Atomically update affinity")
fixed the driver to use writeb_relaxed() instead of writel_relaxed().
As it turns out, the interconnect used on this system mandates
32bit wide accesses for all MMIO transactions, even if the GIC
architecture specifically mandates for some registers to be byte
accessible. Gahhh...
Work around the issue by crudly detecting the offending system,
and falling back to an inefficient RMW+lock implementation.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/CAMuHMdV+Ev47K5NO8XHsanSq5YRMCHn2gWAQyV-q2LpJVy9HiQ@mail.gmail.com
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which always
return IRQ_HANDLED which turns the spurious interrupt detection into a
pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level flow
handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=FIKh
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which
always return IRQ_HANDLED which turns the spurious interrupt
detection into a pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level
flow handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements"
* tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
irqchip: gic-pm: Remove redundant error log of clock bulk
irqchip/sun4i: Remove unnecessary oom message
irqchip/irq-imx-gpcv2: Remove unnecessary oom message
irqchip/imgpdc: Remove unnecessary oom message
irqchip/gic-v3-its: Remove unnecessary oom message
irqchip/gic-v2m: Remove unnecessary oom message
irqchip/exynos-combiner: Remove unnecessary oom message
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
...
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The vGIC advertising code is unsurprisingly very much tied to
the GIC implementations. However, we are about to extend the
support to lesser implementations.
Let's dissociate the vgic registration from the GIC code and
move it into KVM, where it makes a bit more sense. This also
allows us to mark the gic_kvm_info structures as __initdata.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
handle_percpu_devid_fasteoi_ipi() states:
* The biggest difference with the IRQ version is that the interrupt is
* EOIed early, as the IPI could result in a context switch, and we need to
* make sure the IPI can fire again
All that can actually happen scheduler-wise within the handling of an IPI
is the raising of TIF_NEED_RESCHED (and / or folding thereof into
preempt_count); see scheduler_ipi() or sched_ttwu_pending() for instance.
Said flag / preempt_count is evaluated some time later before returning to
whatever context was interrupted, and this gates a call to
preempt_schedule_irq() (arm64_preempt_schedule_irq() in arm64).
Per the above, SGI's do not need a different handler than PPI's, so make
them use the same (handle_percpu_devid_irq).
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201109094121.29975-2-valentin.schneider@arm.com
Introduce a static key identifying Samsung's unique creation, allowing
to replace the indirect call to compute the base addresses with
a simple test on the static key.
Faster, cheaper, negative diffstat.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Change the way we deal with GIC SGIs by turning them into proper
IRQs, and calling into the arch code to register the interrupt range
instead of a callback.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we are about to change quite a lot of the SMP support code,
let's start by moving it around so that it minimizes the amount
of #ifdefery.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The GIC irqchips can now use a HW resend when a retrigger is invoked by
check_irq_resend(). However, should the HW resend fail, check_irq_resend()
will still attempt to trigger a SW resend, which is still a bad idea for
the GICs.
Prevent this from happening by setting IRQD_HANDLE_ENFORCE_IRQCTX on all
GIC IRQs. Technically per-cpu IRQs do not need this, as their flow handlers
never set IRQS_PENDING, but this aligns all IRQs wrt context enforcement:
this also forces all GIC IRQ handling to happen in IRQ context (as defined
by in_irq()).
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200730170321.31228-3-valentin.schneider@arm.com
While digging around IRQCHIP_EOI_IF_HANDLED and irq/resend.c, it has come
to my attention that the IRQ resend situation seems a bit precarious for
the GIC(s).
When marking an IRQ with IRQS_PENDING, handle_fasteoi_irq() will bail out
and issue an irq_eoi(). Should the IRQ in question be re-enabled,
check_irq_resend() will trigger a SW resend, which will go through the flow
handler again and issue *another* irq_eoi() on the *same* IRQ
activation. This is something the GIC spec clearly describes as a bad idea:
any EOI must match a previous ACK.
Implement irq_chip.irq_retrigger() for the GIC chips by setting the GIC
pending bit of the relevant IRQ. After being called by check_irq_resend(),
this will eventually trigger a *new* interrupt which we will handle as usual.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200730170321.31228-2-valentin.schneider@arm.com
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to
use sparse interrupts.
- Cleanups, fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl8pDL0THHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoRTFEACYvH2LnSu1GlXB0XtL3+XyV8bWN3Yr
Qfcp9JbIibx65YkJjcyvfBNA6GjXoogMr9vOHeRVnPtOwzl/7n/lnh/43d6+YPot
7UvIjGtpH3E/lF0kJKfuEsM8CX8DcVhn6dV/T+dJ00m69dAVQHNRsVqAi1/iWEeT
9vBBELoJL79BU2g83NQZ7V0UrqiA5QlPYLpbSffliE6UWjG6XTH2CPM5XucuySNQ
es3szxQ55rtPEzqCHVL0YW75vV39bmKZPqoApA/XQDJrp3bgftjdldoTe7YPQfSG
MXAvB+6axPD+mdeag7/XZFC1DcMx8CnistZSJKpdYZe7mQ7iunfeJRhkEzb+DrO1
WdcDcYOm0rLHhPrUZItJdACjuPNmN9pMaK1PbabsivnHVWzMYYKmMwbW+AEsygGW
nnlsZP1Nr61Mo7O8+EKmxDdox4Qjk3lmQl4SdQgUKNKsI5yFYjvt2CfCjWLQJNBa
w7YiLnL9IChXwrvdGqMIoEueUi0pC3gGbZ/bjDbxI4NJxJgEEav49m/prxM2A2Pl
gfNdwlM1xgNydIBgt/jij/a8Lmv555RuZmvDV7QV7fFwaIqt3Qb5cs0Roq+GlzZR
e0wuikGl0r/Bdow62rle7EysbBBGosAYf6K/kaGhd8v/kx2ByDnPPWzOqtxc+K+i
Iw/daEQRsSnWuw==
=KA8b
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual boring updates from the interrupt subsystem:
- Infrastructure to allow building irqchip drivers as modules
- Consolidation of irqchip ACPI probing
- Removal of the EOI-preflow interrupt handler which was required for
SPARC support and became obsolete after SPARC was converted to use
sparse interrupts.
- Cleanups, fixes and improvements all over the place"
* tag 'irq-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/loongson-pch-pic: Fix the misused irq flow handler
irqchip/loongson-htvec: Support 8 groups of HT vectors
irqchip/loongson-liointc: Fix misuse of gc->mask_cache
dt-bindings: interrupt-controller: Update Loongson HTVEC description
irqchip/imx-intmux: Fix irqdata regs save in imx_intmux_runtime_suspend()
irqchip/imx-intmux: Implement intmux runtime power management
irqchip/gic-v4.1: Use GFP_ATOMIC flag in allocate_vpe_l1_table()
irqchip: Fix IRQCHIP_PLATFORM_DRIVER_* compilation by including module.h
irqchip/stm32-exti: Map direct event to irq parent
irqchip/mtk-cirq: Convert to a platform driver
irqchip/mtk-sysirq: Convert to a platform driver
irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros
irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros
irqchip: irq-bcm2836.h: drop a duplicated word
irqchip/gic-v4.1: Ensure accessing the correct RD when writing INVALLR
irqchip/irq-bcm7038-l1: Guard uses of cpu_logical_map
irqchip/gic-v3: Remove unused register definition
irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module
genirq: Export irq_chip_retrigger_hierarchy and irq_chip_set_vcpu_affinity_parent
irqdomain: Export irq_domain_update_bus_token
...
In an effort to enable -Wcast-function-type in the top-level Makefile to
support Control Flow Integrity builds, there are the need to remove all
the function callback casts.
To do this, modify the IRQCHIP_ACPI_DECLARE macro to use the new defined
macro ACPI_DECLARE_SUBTABLE_PROBE_ENTRY instead of the macro
ACPI_DECLARE_PROBE_ENTRY. This is necessary to be able to initialize the
the acpi_probe_entry struct using the probe_subtbl field instead of the
probe_table field and avoid function cast mismatches.
Also, modify the prototype of the functions used by the invocation of the
IRQCHIP_ACPI_DECLARE macro to match all the parameters.
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20200530143430.5203-3-oscar.carter@gmx.com
The GIC driver uses a RMW sequence to update the affinity, and
relies on the gic_lock_irqsave/gic_unlock_irqrestore sequences
to update it atomically.
But these sequences only expand into anything meaningful if
the BL_SWITCHER option is selected, which almost never happens.
It also turns out that using a RMW and locks is just as silly,
as the GIC distributor supports byte accesses for the GICD_TARGETRn
registers, which when used make the update atomic by definition.
Drop the terminally broken code and replace it by a byte write.
Fixes: 04c8b0f82c ("irqchip/gic: Make locking a BL_SWITCHER only feature")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
(E)PPIs are per-CPU interrupts, so we want each CPU to go and enable them
via enable_percpu_irq(); this also means we want IRQ_NOAUTOEN for them as
the autoenable would lead to calling irq_enable() instead of the more
appropriate irq_percpu_enable().
Calling irq_set_percpu_devid() is enough to get just that since it trickles
down to irq_set_percpu_devid_flags(), which gives us IRQ_NOAUTOEN (and a
few others). Setting IRQ_NOAUTOEN *again* right after this call is just
redundant, so don't do it.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200521223500.834-1-valentin.schneider@arm.com
GICv3.1 allows up to 80 PPIs (16 legaci PPIs and 64 Extended PPIs),
meaning we can't just leave the old 16 hardcoded everywhere.
We also need to add the infrastructure to discover the number of PPIs
on a per redistributor basis, although we still pretend there is only
16 of them for now.
No functional change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
gic_configure_irq is currently passed the (re)distributor address,
to which it applies an a fixed offset to get to the configuration
registers. This offset is constant across all GICs, or rather it was
until to v3.1...
An easy way out is for the individual drivers to pass the base
address of the configuration register for the considered interrupt.
At the same time, move part of the error handling back to the
individual drivers, as things are about to change on that front.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not have any in-tree platform with this pathological setup,
and only a single system (Cavium's cns3xxx) isn't DT aware.
Let's drop the secondary GIC support for now, until we remove
the above horror altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Go over the IRQ subsystem source code (including irqchip drivers) and
fix common typos in comments.
No change in functionality intended.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
No changes in semantics -- key init is true; replace
static_key_slow_dec with static_branch_disable
static_key_true with static_branch_likely
The first is because we never actually do any couterpart incs,
thus there is really no reference counting semantics going on.
Use the more proper static_branch_disable() construct.
Also added a '_key' suffix to supports_deactivate, for better
self documentation.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.
People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Booting a crash kernel while in an interrupt handler is likely
to leave the Active Priority Registers with some state that
is not relevant to the new kernel, and is likely to lead
to erratic behaviours such as interrupts not firing as their
priority is already active.
As a sanity measure, wipe the APRs clean on startup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs, and
after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaDayXAAoJEED/6hsPKofo/3UH/3HvlcHt+ADTkCU1/iiKAs+i
0zngIOXIxgHDnV0ww6bV+Znww0BzTYgKCAXX76z603jdpDwG/pzQQcbLDF5ZoJnD
sQtF10gZinWaRsHlfbLqjrHGL2pGDHO1UKBKLJ0bAIyORPZBxs7i+VmrY/blnr9c
0wsybJ8RbvwAxjsDL5jeX/z4NehPupmKUc4Lf0eZdSHwVOf9sjn+MP6jJ0r2JcIb
D+zddPBiLStzN97t4gZpQsrlj3LKrDS+6hY+1TjSvlh+yHKFVFh58VhLm4DuDeb5
bYOAlWJ/gAWEzfvr5Ld+Nd7SqWWn/14logPkQ4gcU4BI/neAOzk4c6hJfCHl1nk=
=593n
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"First batch of KVM changes for 4.15
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs,
and after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups"
* tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (89 commits)
KVM: s390: provide a capability for AIS state migration
KVM: s390: clear_io_irq() requests are not expected for adapter interrupts
KVM: s390: abstract conversion between isc and enum irq_types
KVM: s390: vsie: use common code functions for pinning
KVM: s390: SIE considerations for AP Queue virtualization
KVM: s390: document memory ordering for kvm_s390_vcpu_wakeup
KVM: PPC: Book3S HV: Cosmetic post-merge cleanups
KVM: arm/arm64: fix the incompatible matching for external abort
KVM: arm/arm64: Unify 32bit fault injection
KVM: arm/arm64: vgic-its: Implement KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: Document KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: vgic-its: Free caches when GITS_BASER Valid bit is cleared
KVM: arm/arm64: vgic-its: New helper functions to free the caches
KVM: arm/arm64: vgic-its: Remove kvm_its_unmap_device
arm/arm64: KVM: Load the timer state when enabling the timer
KVM: arm/arm64: Rework kvm_timer_should_fire
KVM: arm/arm64: Get rid of kvm_timer_flush_hwstate
KVM: arm/arm64: Avoid phys timer emulation in vcpu entry/exit
KVM: arm/arm64: Move phys_timer_emulate function
KVM: arm/arm64: Use kvm_arm_timer_set/get_reg for guest register traps
...
Some systems without proper firmware and/or hardware description data
don't support the split EOI and deactivate operation.
On such systems, we cannot leave the physical interrupt active after the
timer handler on the host has run, so we cannot support KVM with an
in-kernel GIC with the timer changes we are about to introduce.
This patch makes sure that trying to initialize the KVM GIC code will
fail on such systems.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
There is a lot of broken firmware out there that don't really
expose the information the kernel requires when it comes with dealing
with GICv2:
(1) Firmware that only describes the first 4kB of GICv2
(2) Firmware that describe 128kB of CPU interface, while
the usable portion of the address space is between
60 and 68kB
So far, we only deal with (2). But we have platforms exhibiting
behaviour (1), resulting in two sub-cases:
(a) The GIC is occupying 8kB, as required by the GICv2 architecture
(b) It is actually spread 128kB, and this is likely to be a version
of (2)
This patch tries to work around both (a) and (b) by poking at
the outside of the described memory region, and try to work out
what is actually there. This is of course unsafe, and should
only be enabled if there is no way to otherwise fix the DT provided
by the firmware (we provide a "irqchip.gicv2_force_probe" option
to that effect).
Note that for the time being, we restrict ourselves to GICv2
implementations provided by ARM, since there I have no knowledge
of an alternative implementations. This could be relaxed if such
an implementation comes to light on a broken platform.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
-----BEGIN PGP SIGNATURE-----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=3ZS3
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for 4.14 from Marc Zyngier:
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
Make this const as it is only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-4-marc.zyngier@arm.com
Devices that expose their interrupt status registers via system
registers (e.g. Statistical profiling, CPU PMU, DynamIQ PMU, arch timer,
vgic (although unused by Linux), ...) rely on a context synchronising
operation on the CPU to ensure that the updated status register is
visible to the CPU when handling the interrupt. This usually happens as
a result of taking the IRQ exception in the first place, but there are
two race scenarios where this isn't the case.
For example, let's say we have two peripherals (X and Y), where Y uses a
system register for its interrupt status.
Case 1:
1. CPU takes an IRQ exception as a result of X raising an interrupt
2. Y then raises its interrupt line, but the update to its system
register is not yet visible to the CPU
3. The GIC decides to expose Y's interrupt number first in the Ack
register
4. The CPU runs the IRQ handler for Y, but the status register is stale
Case 2:
1. CPU takes an IRQ exception as a result of X raising an interrupt
2. CPU reads the interrupt number for X from the Ack register and runs
its IRQ handler
3. Y raises its interrupt line and the Ack register is updated, but
again, the update to its system register is not yet visible to the
CPU.
4. Since the GIC drivers poll the Ack register, we read Y's interrupt
number and run its handler without a context synchronisation
operation, therefore seeing the stale register value.
In either case, we run the risk of missing an IRQ. This patch solves the
problem by ensuring that we execute an ISB in the GIC drivers prior
to invoking the interrupt handler. This is already the case for GICv3
and EOIMode 1 (the usual case for the host).
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the GIC cannot map an IRQ via irq_domain_ops->alloc(), it doesn't
return an error code. This can cause a problem with drivers, where
it thinks it has successfully got an IRQ for the device, but requesting
the same ends up failure with -ENOSYS (as the IRQ's chip is not set).
Fixes: commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq domain.")
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
