Remove the new unused DMA controller definitions from mach/SA-1100.h.
These are now private to the SA-11x0 DMA engine driver and contained
within the driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that all users are converted over to using the DMA engine API,
we can get rid of the old platform dependent DMA driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sa1111 support will ioremap() the device; there is no need for
platforms to setup a static mapping for this. Remove the static
mapping for this device from badge4, jornada720 and neponset.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use dev_err() to report device specific errors rather than printk().
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the releasing of resources out of the release function - this
allows a cleaner and more conventional arrangement of the registration
failure paths and a saner unregistration process for these devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's pointless registering the PS/2 interfaces with the dmabounce code
when there's no DMA support for these in hardware, so only setup the
DMA masks for two subdevices which support DMA - the OHCI and SAC.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the bus notifier to register sa1111 devices with dmabounce, rather
than after the device has been registered, potentially racing with
driver binding.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the USB interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the PCMCIA interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the PS/2 interface register definitions into the driver, rather
than keeping them in a common location.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the unused GPIO register definitions - we access GPIO
registers through the base + offset method, and having the phys
address definitions is unnecessary duplication.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms don't want certain devices to be registered, because,
eg, the interface is not wired. Provide a way for platforms to
prevent various devices from being registered via a devid bitmask in
the platform data.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add sa11x0 DMA platform device and resources to the list of
generic platform devices for SA11x0 machines.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the sa1111 device id to be a bitmask. This allows us to
specify the actual device, while allowing a single driver to bind
to both PS2 devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the handling of the 5v supply into badge4.c, removing this board
specific detail from the sa1111 ohci driver.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform hooks to be called when individual sa1111 devices are
enabled and disabled. This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a shutdown hook to the sa1111_driver structure to allow drivers
to be notified of system reboots and shutdowns.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the necessary allocation/freeing functionality to support
sparse IRQs with the SA-1111 device. On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 19851c58e6 (sa1111: allow cascaded IRQs to be used by platforms)
moved the IRQ definitions to the .c file, and added an irq_base member
to the private data structure.
The inerrupt demultiplexer uses irq_base, but the interrupt setup code
does not. Also, although the commit adds a private data structure to
pass this data, it isn't even referenced, resulting in irq_base being
zero.
We also copied the IRQ numbers from the device info array into the actual
devices, resulting in wrong interrupt numbers passed to the sub-devices.
The net effect of this is that we always overwrite IRQs 0-54, even if
they are allocated elsewhere in the system.
Add the code necessary to setup the private irq_base, and use it in the
IRQ setup code. Make the SA-1111 probe fail with -EINVAL if there is no
platform data provided.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an initializer for the struct device_driver .owner member.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should not write to the SA1111 registers after setting the SLEEP
bit. Moreover, the manual says that the PWM registers should be
disabled before we enter sleep. So, move the clearing of these
registers earlier in the suspend sequence.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We weren't re-enabling the memory request/grant signals on resume,
causing DMA devices on the sa1111 to fail.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we ioremap() the neponset register space, there's no need
to static map the neponset registers. Get rid of this static mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the board specific neponset register definitions to the board
file, rather than mach/neponset.h. However, as the NCR_0 register
definitions are used by some drivers, leave these behind.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The neponset board is a daughter board for the Assabet. Create the
neponset platform device in assabet.c, where we don't have to wrap
it with machine_is_assabet() stuff. We also create this device
dynamically rather than keeping it as a static device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suspend and resume in the _noirq state, so that we're saving the
state of the modem control signals as late as possible, and restoring
them as early as possible. There's nothing to do in thaw/poweroff
methods as we've already saved the necessary state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Complete the neponset device resources by covering the children's
memory resources in the parent neponset device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Obtain the parent IRQ from the neponset device resource rather than
hard-coding it into the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the necessary allocation/freeing functionality to support
sparse IRQs with the Neponset device. On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use platform_device_register_full() to dynamically create the various
neponset child platform devices, and place them below the neponset
device itself to ensure proper PM ordering and device structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Save and restore the modem output control register across a suspend/
resume, as well as the NCR register. Place these in a locally
allocated data structure rather than needing a new static variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having direct register accesses to NCR_0 scattered amongst
the code, provide a function instead. This contains the necessary
race protection for this platform, ensuring that updates to this
register are safe.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since ARM was converted to genirq, the neponset IRQ implementation has
gradually broken as a result of various subtle changes being introduced
into genirq.
It used to be that simple IRQs did not need an IRQ chip. This is no
longer the case, and genirq barfs in irq_set_handler(). Fix this by
introducing a dummy no-op chip, and registering it along with the flow
handler.
Neponset IRQs really don't have any masking ability - all we have is a
status register to allow us to decode the source, and a three input OR
gate inside a CPLD.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO27 is just connected to a CPLD input without any pull-ups or pull-
downs. If GPIO27 is left as an input, it will float around mid-supply,
which for CMOS inputs is the worst place for a pin to be. Ensure that
this pin is driven.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid glitching the GPIO signals during initialization, which can
have undesirable effects. Ensure that the desired pin state is set
before we change the GPIO pin direction to be an output.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Neponset calls sa1110_mb_disable() from __devinit code, but
sa1110_mb_disable() is marked __init, and so causes a section
mismatch warning.
As sa1110_mb_enable() and sa1110_mb_disable() need to be callable
from suspend/resume paths as well, they must not be marked __init
or __devinit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sometimes, we get stuck while trying to enter sleep. This seems
to occur if we do not have udelay() in the instruction cache. Avoid
this by requesting a short delay prior to modifying the SDRAM timings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hackkit defined its flash memory resource to be 32M + 1 byte.
Jornada defined the Epson video controller resources to be one byte
larger than they should be, and mis-mapped the SA-1111 companion
chip one byte smaller than it should be.
Fix these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
Kevin Cernekee reported that recent cleanup
that replaced pci_iomap with a generic function
failed to take into account the differences
in io port handling on mips and sh architectures.
Rather than revert the changes reintroducing the
code duplication, this patchset fixes this
by adding ability for architectures to override
ioport mapping for pci devices.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPL9X8AAoJECgfDbjSjVRpgzgIAIQGeWIP0JUWDDhLfYscTBZx
96Am+8+maVl12t+evVH8lMnJDSqjKH0kWxk6CTQSUo57gZ4ne1SxbZ0+s5DcsE6m
XAnIvkA+4pw36l4QRkEj8g+yrhpQhqaiKJt/l80jaVFGVAw47WrxGKatUe9L90lI
X7+xa/F5zvZO6oamEI94SAojIvmKkZfHIjGc/NaZLaWHRysdFf8Ek13mj2+9FLq3
dxmg9F14eS2X59tIkN4BLM4Dq8UyZqraT0N/0bO0Tetqx0azzNZbsBsg5RwQ15IF
Ei0dMFARoT9UcIpdSwtpGGCoqYa5yRHFT1g54hv/Pon0mKUjG7Fpz5LRWmZ5Xic=
=b1R2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
arch: fix ioport mapping on mips,sh
Kevin Cernekee reported that recent cleanup that replaced pci_iomap with
a generic function failed to take into account the differences in io
port handling on mips and sh architectures.
Rather than revert the changes reintroducing the code duplication, this
patchset fixes this by adding ability for architectures to override
ioport mapping for pci devices.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
sh: use the the PCI channels's io_map_base
mips: use the the PCI controller's io_map_base
lib: add NO_GENERIC_PCI_IOPORT_MAP
Fixing a regression with the PMU MSRs when PMU virtualization is
disabled, a guest-internal DoS with the SYSCALL instruction, and a dirty
memory logging race that may cause live migration to fail.
* 'kvm-updates/3.3' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: do not #GP on perf MSR writes when vPMU is disabled
KVM: x86: fix missing checks in syscall emulation
KVM: x86: extend "struct x86_emulate_ops" with "get_cpuid"
KVM: Fix __set_bit() race in mark_page_dirty() during dirty logging
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tFsG
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc
* A series of OMAP regression fixes for merge window fallout
* Two patches for Davinci, one removes some misdefined clocks, the other
is a regression fix for merge window fallout
* Two patches that makes Broadcom bcmring build again (and removes a
bunch of unused code in the process)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcmring: fix build failure in mach-bcmring/arch.c
ARM: bcmring: remove unused DMA map code
ARM: davinci: update mdio bus name
ARM: OMAP2+: arch/arm/mach-omap2/smartreflex.c: add missing iounmap
ARM: OMAP2+: arch/arm/mach-omap2/devices.c: introduce missing kfree
ARM: OMAP: fix MMC2 loopback clock handling
ARM: OMAP: fix erroneous mmc2 clock change on mmc3 setup
ARM: OMAP2+: GPMC: fix device size setup
ARM: OMAP2+: timer: Fix crash due to wrong arg to __omap_dm_timer_read_counter
ARM: OMAP3: hwmod data: register dss hwmods after dss_core
ARM: OMAP2/3: PRM: fix missing plat/irqs.h build breakage
ARM: OMAP2+: io: fix compilation breakage on 2420-only configs
ARM: OMAP4: hwmod data: Add names for DMIC memory address space
ARM: OMAP3: hwmod data: add SYSC_HAS_ENAWAKEUP for dispc
ARM: OMAP2+: hwmod data: split omap2/3 dispc hwmod class
ARM: davinci: DA850: remove non-existing pll1_sysclk4-7 clocks
ARM: OMAP2: fix regulator warnings
ARM: OMAP2: fix omap3 touchbook kconfig warning
i2c: OMAP: Fix OMAP1 build error
Upstream commit d1fce9c115
"ARM: restart: bcmring: use new restart hook"
breaks building of this platform, since what used to be the
last field of the MACHINE_START/END block didn't have a
trailing comma. Once another field was added below, we get:
arch/arm/mach-bcmring/arch.c:198: error: request for member 'restart' in something not a structure or union
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove BCMRING DMA map code which is no longer used.
This also fixes a build error with dma.c introduced by
bfcd2ea6a4.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
