Different chipsets may use different TXWI descriptor
size. Instead of using a hardcoded value, use the
'queue->winfo_size' which holds the correct value for
a given device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code uses the same index value both
for the channel information array and for the TX
power table. The index starts from 14, however the
index of the TX power table must start from zero.
Fix it, in order to get the correct TX power value
for a given channel.
The changes in rt61pci.c and rt73usb.c are compile
tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch complains that this is a read past the end of the array. It
turns out we are printing the wrong array here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since platform support is required for WoW, identify and
and enable Wow only for supported cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of these relate to endianness problems, and are purely cosmetic.
But a couple of them were legit -- listen interval parsing and some of
the rate selection code would malfunction on BE systems.
There's still one cosmetic warning remaining, in the (admittedly) ugly
code in cw1200_spi.c. It's there because the hardware needs 16-bit SPI
transfers, but many SPI controllers only operate 8 bits at a time.
If there's a cleaner way of handling this, I'm all ears.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to return -ENOMEM in the ipw_rx_queue_alloc() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_txqaddbuf assumes that all the linked buffers in the queue passed
to it are part of the same A-MPDU or MPDU. The CAB queue rework violates
this assumption, which can cause the internal queue depth to go
negative.
Fix this by increasing the counter for all slots of [bf, bf->bf_lastbf]
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This provides some of the same info found in
the ath9k_htc debugfs through the standard ethtool stats API.
This logic is only supported when ath9k_htc debugfs kernel
feature is enabled, since that is the only time stats
are actually gathered.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that a chip reset is done when IDLE is turned
off - this fixes authentication timeouts.
Cc: stable@vger.kernel.org
Reported-by: Ignacy Gawedzki <i@lri.fr>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_txq_schedule is called outside of the drv_tx call, so it needs RCU
protection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the notification code, a couple of places build fdb entries on
the stack, use structure initialization instead and fix formatting.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Based on initial work by Mike Rapoport <mike.rapoport@ravellosystems.com>
Use list macros and RCU for tracking multiple remotes.
Note: this code assumes list always has at least one entry,
because delete is not supported.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The function vxlan_xmit_one always returns NETDEV_TX_OK, so there
is no point in keeping track of return values etc.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Put destruction of per-cpu statistics removal in
ndo_uninit since it is created by ndo_init.
This also avoids any problems that might be cause by destructor
being called after module removed.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
It is possible for two cpu's to race creating vxlan device.
For most cases this is harmless, but the ability to assign "next
avaliable vxlan device" relies on rtnl lock being held across the
whole operation. Therfore two instances of calling:
ip li add vxlan%d vxlan ...
could collide and create two devices with same name.
To fix this defer creation of socket to a work queue, and
handle possible races there. Introduce a lock to ensure that
changes to vxlan socket hash list is SMP safe.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Do join/leave from work queue to avoid lock inversion problems
between normal socket and RTNL. The code comes out cleaner
as well.
Uses Cong Wang's suggestion to turn refcnt into a real atomic
since now need to handle case where last use of socket is IGMP
worker.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Switch to using a per module work queue so that all the socket
deletion callbacks are done when module is removed.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
If vxlan is removed with active vxlan's it would crash because
rtnl_link_unregister (which calls vxlan_dellink), was invoked
before unregister_pernet_device (which calls vxlan_stop).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This fixes an issue caused by submit 78c3bcc5d1
`bnx2x: Improve PF behaviour toward VF', which made the bnx2x driver fail
compilation when PCI_IOV is not set.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
I would guess that this is the last big wireless pull request before
the 3.11 merge window...
Regarding the mac80211 bits, Johannes says:
"I have a number of mesh fixes and improvements from Colleen, Jacob,
Ashok and Thomas, powersave fixes in mac80211 from Alex, improved
management-TX from Antonio, and a few various things, including locking
fixes, from others and myself. Overall though, nothing really stands
out."
As for the iwlwifi bits, Johannes says:
"Emmanuel contributed two AP mode fixes, removed an unused field, fixed a
comment and added a warning for something that shouldn't happen in
practice, and I removed the declaration of a function that doesn't even
exist and cleaned up a small include."
"This time I have a number of cleanups, a small fix from Emmanuel and two
performance improvements that combined reduce our driver's CPU
utilisation as much as 75% in high TX-throughput scenarios."
"These two patches fix two issues with using rfkill randomly during
traffic, which would then cause our driver to stop working and not be
able to recover at all."
Regarding the ath6kl bits, Kalle says:
"Here are few simple patches for ath6kl. We have a suspend crash fix for
USB from Shafi, use of mac_pton(), a compiler warning fix and a fix for
module initialisation error path."
Kalle also sends the biggest single item of note, the new ath10k
driver for Qualcomm Atheros 802.11ac CQA98xx devices.
Included is an NFC pull, of which Samuel says:
"These are the pending NFC patches for the 3.11 merge window.
It contains the pending fixes that were on nfc-fixes (nfc-fixes-3.10-2),
along with a few more for the pn544 and pn533 drivers, the LLCP
disconnection path and an LLCP memory leak.
Highlights for this one are:
- An initial secure element API. NFC chipsets can carry an embedded
secure element or get access to the SIM one. In both cases they
control the secure elements and this API provides a way to discover,
enable and disable the available SEs. It also exports that to
userspace in order for SE focused middleware to actually do something
with them (e.g. payments).
- NCI over SPI support. SPI is the most complex NCI specified transport
layer and we now have support for it in the kernel. The next step will
be to implement drivers for NCI chipsets using this transport like
e.g. bcm2079x.
- NFC p2p hardware simulation driver. We now have an nfcsim driver that
is mostly a loopback device between 2 NFC interfaces. It also
implements the rest of the NFC core API like polling and target
detection. This driver, with neard running on top of it, allows us to
completely test the LLCP, SNEP and Handover implementation without
physical hardware.
- A Firmware update netlink API. Most (All ?) HCI chipsets have a
special firmware update mode where applications can push a new
firmware that will be flashed. We now have a netlink API for providing
that mode to e.g. nfctool."
On top of all that, there are a variety of updates to brcmfmac,
iwlegacy, rtlwifi, wil6210, and the TI wl12xx drivers. As usual,
the bcma and ssb busses get a little love as well, as do a handful
of others here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit a4791254b6
("qlcnic: change mdelay to msleep") which overwrote a commit
68b3f28c11
("qlcnic: Fix scheduling while atomic bug")
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_suspend':
drivers/net/ethernet/ti/cpsw.c:1979:26: error: 'priv' undeclared (first use in this function)
drivers/net/ethernet/ti/cpsw.c:1979:26: note: each undeclared identifier is reported only once for each function it appears in
make[4]: *** [drivers/net/ethernet/ti/cpsw.o] Error 1
The compilation error was introduced by the following commit
6d3d76f (drivers: net: cpsw: fix cpsw clock gating issue across suspend/resume)
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here, "i" vs "j", so we would crash on module_exit().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to obviously missing braces, EESR.TABT (transmit abort) interrupt may be
reported even if it hasn't happened, just when EESR.TWB (transmit descriptor
write-back) interrupt happens. Luckily (?), EESR.TWB is disabled by the driver
via the TRIMD register and all the interrupt masks, so that transmit abort is
never actually logged...
Put the braces where they should be and fix the incoherent comment, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EESR.RFE (receive FIFO overflow) interrupt is enabled by the driver on all SoCs
and sh_eth_error() handles it but it's not present in any initializer/assignment
of the 'eesr_err_check' field of 'struct sh_eth_cpu_data'. This leads to that
interrupt not being handled and cleared, and finally to disabling IRQ and the
driver being non-functional.
Modify DEFAULT_EESR_ERR_CHECK macro and all explicit initializers of the above
mentioned field to contain the EESR.RFE bit. Remove useless backslashes from the
initializers, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found in the Windows INF files while investigating the
Novatel/Verizon USB-1000 device. The USB-1000 is verified as
a Gobi1K device and works with QMI after loading appropriate
firmware.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the DMA mapping may fail the caller should check the return value.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have BOND_LINK_UP the speed is reported unconditionally with %u
format although it can be SPEED_UNKNOWN (-1). After this patch it returns
0 in that case in an attempt to keep the existing scripts happy.
One line is intenionally left 81 chars because it gets ugly if broken.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old hypervisors don't mask out timestamp capability for slave. Till slave
support will be added, need to disable capability by slave.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't claim 20G is supported if the speed is unsupported by the phys
(reflected by various ethtools and ndos).
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wait 100ms for FLR to complete in parallel over all VFs instead of serializing
the waits (which can amount to several seconds with 64 VFs).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If iproute2 VF callbacks are invoked before PF is loaded,
abort gracefully.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Implement shutdown and resume handlers for 83xx.
o Refactor 82xx shutdown and resume handlers.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue 'set driver version' during driver load and after reset recovery
to notify the driver version to the firmware.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to read memory section of adapter
dump using PEX DMA method. This method significantly improves
total adapter dump collection time.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Minimize sleep duration and check for adapter status.
o Exit from loopback test if adapter reset is detected.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring secondary unicast address which
will use existing HW filters to store all the unicast MAC
addresses and prevent device going into promiscuous mode.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_alloc_mbx_args() may fail due to failure in memory allocation.
This patch checks for failure of qlcnic_alloc_mbx_args() to avoid
potential invalid memory access.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci core has been saved pm cap register offset by pdev->pm_cap in pci_pm_init()
in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci core has been saved pm cap register offset by pdev->pm_cap in pci_pm_init()
in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: netdev@vger.kernel.org (open list:NETWORKING DRIVERS)
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in bnx2x_init_dev().
Also remove redundant PM Cap find code, because pci core
has been saved the pci device pm cap value.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has no dependency on any of the drivers under NET_CORE.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, cleanup bond_alb_handle_active_change() from 2 identical ifs.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero pointer in rx_skb is how respective rxq_deinit() finds out out that a skb
slot is unallocated. If rxq_refill() fails (e.g. on OOM condition), subsequent
teardown would result in an attempt to kfree() invalid pointers.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero pointer in rx_skb or tx_skb is how respective *_deinit() functions find
out that a skb slot is unallocated. If *_init() functions unsuccessfully return
after the allocation (e.g. when subsequent dma_alloc_coherent() is not
successful), this would result in attempt to kfree() invalid pointers.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Kosta Zertsekel <konszert@marvell.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver probe currently results in:
WARNING: at drivers/base/core.c:576 device_create_file+0x57/0x7e()
Attribute phy_type: write permission without 'store'
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The C ABI reverses the bitfield fill order when compiled as
little-endian.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous fix was still too agressive to meet ieee specs. Increase
to (14, 10).
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_find_vfs() is no longer needed as the common PCI calls provide the same
functionality.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the EEE setup allowing to configure this support
when the link changes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to some hardware integration issue, CPSW sliver modules requires a
reset across suspend/resume cycle for a successful clock gating to
CPGMAC (CPSW and Davinci MDIO) in AM335x PG1.0.
This issue is fixed in PG2.x, though to support suspend/resume on PG1.0
this reset is required.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check next packet availability by validating that HW has finished CQE
placement. This saves latency of another dma transaction performed to update
SB indexes.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds ndo_ll_poll method and locking for FPs between LL and the napi.
When receiving a packet we use skb_mark_ll to record the napi it came from.
Add each napi to the napi_hash right after netif_napi_add().
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for LLS.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor various ip tunnels xmit functions and extend iptunnel_xmit()
so that there is more code sharing.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only R8A7740 specific #ifdef hindering ARM multiplatform build is left in
sh_eth_rx(): it covers the code shifting Rx buffer descriptor word 0 by 16. Get
rid of the #ifdef by adding 'shift_rd0' field to the 'struct sh_eth_cpu_data',
making the shift dependent on it, and setting it to 1 for the R8A7740 case...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the comment to 'enum TD_STS_BIT', reformat the values, and add a couple of
values missing before (though unused by the driver).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SH7724 'eesipr_value' field initializer includes DMAC_M_RFRMER & DMAC_M_ECI
bits which are already contained in 0x01ff009f -- remove them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'tx_error_check' field of 'struct sh_eth_cpu_data' is write-only, so remove
it along with the DEFAULT_TX_ERROR_CHECK macro.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver hasn't used NAPI so far; implement its support at last...
The patch was tested on Renesas R8A77781 BOCK-W board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_interrupt() uses the same Rx interrupt mask twice to check the interrupt
status register -- #define EESR_RX_CHECK and use it instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.
fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)
Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
After receiving channel switch announcement from AP, scan and
association on that channel is blocked for DFS_CHAN_MOVE_TIME
(10 seconds). Hence station will be able to connect to the AP,
once it is moved to new channel.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to parse requested AP's 11h capabilities
and add 11h information in association request.
Also, deauth is sent to the AP after receiving channel switch
announcement event from firmware. This happens when AP advertises
WLAN_EID_CHANNEL_SWITCH IE in it's beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not unconditionally access the chan variable in
brcmf_cfg80211_mgmt_tx() as it may be NULL.
Use freq instead.
Introduced by c2ff8cad64
("brcm80211: make mgmt_tx in brcmfmac accept a NULL channel")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use negative check (if(!bss_desc)) and return failure
instead of failing a NULL check later in
mwifiex_check_network_compatibility() routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
This patch was originally included as commit 1288aa4, but was accidentally
reverted in a later patch.
Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org> [back to 2.6.39]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check introduced by:
commit 26a41ae604
Author: stephen hemminger <stephen@networkplumber.org>
Date: Mon Jun 17 12:09:58 2013 -0700
vxlan: only migrate dynamic FDB entries
was not correct because it is checking flag about type of FDB
entry, rather than the state (dynamic versus static). The confusion
arises because vxlan is reusing values from bridge, and bridge is
reusing values from neighbour table, and easy to get lost in translation.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Introduce by commit 0ae99b5fed
(bcm63xx_enet: split DMA channel register accesses)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usb_8dev hardware has problems on some xhci USB hosts. The driver fails to
read the firmware revision in the probe function. This leads to the following
Oops:
[ 3356.635912] kernel BUG at net/core/dev.c:5701!
The driver tries to free the netdev, which has already been registered, without
unregistering it.
This patch fixes the problem by unregistering the netdev in the error path.
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Reviewed-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add scatter gather list support for better rx glom performance.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introducing a new SDIO block data access interface function
brcmf_sdio_buffrw. It will act as a unified interface function for any block
data access to WiFi dongle through SDIO interface. This patch enables
the support for single skb transmission.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is an ID table registered to SDIO stack which consists of all SDIO devices
supported by brcmfmac. It is not necessary to have an extra check.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of allocating an empty list item and queue that for
the dpc data worker to dequeue an atomic counter is used.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just cleaning up and being consistent in naming operations
related to struct brcmf_fws_mac_descriptor objects.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware-signalling code used NL80211_NUM_ACS, but it has
its own definition enum brcmf_fws_fifo, which is more appropriate
to use. This effectively removes the need to include nl80211.h.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The term prec (precedence) is different from the fifo number. Rename
use of prec with fifo to be consistent and clear.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware will sent an event message when bc/mc traffic should
be sent to the device using credit mechanism.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 and CUS230 are similar cards, both
are AR9485 + xLNA solutions. But, the subsystem IDs
differ - identify CUS230 explicitly to make things
clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the REGULATORY debug level to print the target power
details. EEPROM can be used for other purposes and this
spams the log.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct spelling typo in printk within various drivers.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The old nl80211 testmode is no longer useful in iwlwifi,
we're moving towards a new model internally and there's
no open tool to use it, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If someone wants to disable AMPDU, there is the 11n_disable
module parameter.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nobody will ever wants to run without this. Make it true always.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This parameter is really not useful, remove it.
Leave the variable in priv in case someone wants
to play with it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the D3 firmware crashes, it can be helpful for debugging to
resume the system to get the SRAM snapshot to see why it crashed.
Allow enabling this with a debugfs option.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change set of 4305b541, "[SK_BUFF]: Convert skb->end to sk_buff_data_t"
converted skb->end from pointer type to sk_buff_data_t.
The pointed value should be accessed via skb_end_pointer().
Since arm arch doesn't define NET_SKBUFF_DATA_USES_OFFSET,
skb->end is effectively pointer. So it doesn't cause a real problem.
But this patch is good for consistency.
Found by inspection. Compile tested only.
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change set of 4305b541 "[SK_BUFF]: Convert skb->end to sk_buff_data_t"
converted skb->end from pointer to sk_buff_data_t.
The pointed value should be accessed via skb_end_pointer().
Since arm or ppc arch doesn't define NET_SKBUFF_DATA_USES_OFFSET,
skb->end is effectively pointer. So it doesn't cause a real problem.
But this patch is good for consistency.
Found by inspection. Compile test only.
Cc: Simon Horman <horms@verge.net.au>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operation to restart autonegotiation via the PHY.
Tested on i.MX28EVK.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alb_set_slave_mac_addr() sets the mac address in alb mode via
dev_set_mac_address(), which might sleep. It's called from
alb_handle_addr_collision_on_attach() in atomic context (under
read_lock(bond->lock)), thus triggering a bug.
Fix this by moving the lock inside alb_handle_addr_collision_on_attach().
v1->v2:
As Nikolay Aleksandrov noticed, we can drop the bond->lock completely.
Also, use bond_slave_has_mac(), when possible.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after priv->cpts got allocated then this pointer should check to determine
if the allocation succeeded or not.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This will probably be the last batch of wireless fixes intended
for 3.10. Many of these are one- or two-liners, and a couple of
others are mostly relocating existing code to avoid races or to
limit the code to effecting specific hardware, etc.
The mac80211 fixes have a couple of exceptions to the above.
Regarding those, Johannes says:
"Following davem's complaint about my patch, here's a new pull request
w/o the patch he was complaining about, but instead with the const
fix rolled into the fix.
I have a fix for radar detection, one for rate control and a workaround
for broken HT APs which is a regression fix because we didn't rely
on them to be correct before."
Johannes also sends some iwlwifi fixes:
"I picked up Nikolay's patch for the chain noise calibration bug
that seems to have been there forever, a fix from Emmanuel for
setting TX flags on BAR frames and a fix of my own to avoid printing
request_module() errors if the kernel isn't even modular. We also
have our own version of Stanislaw's fix for rate control."
Along with those...
Anderson Lizardo fixes a Bluetooth memory corruption bug when an MTU
value is set to too small of a value.
Arend van Spriel sends a revised brcmsmac bug that fixes a regression
caused by a bad return value in an earlier patch. He also sends a
brcmfmac fix to avoid an oops when loading the driver at boot.
Daniel Drake fixes a race condition in btmrvl that causes hangs on
suspend for OLPC hardware.
Johan Hedberg adds a check to avoid sending a
HCI_Delete_Stored_Link_Key command to devices that don't support them,
avoiding some scary looking log spam.
Stanislaw Gruszka gives us a fix for iwlegacy to be able to use rates
higher than 1Mb/s on older wireless networks. He also sends an rt2x00
fix to reinstate older tx power handling behavior for some devices
that didn't work well with the current code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a very simple driver, based on the original vendor
driver that Qualcomm/Atheros published/submitted previously,
but reworked to make the code saner. However, it also lost
a number of features (TSO/GSO, VLAN acceleration and multi-
queue support) in the process, as well as debugging support
features I didn't have any use for. The only thing I left
is checksum offload.
More features can obviously be added, but this seemed like
a good start for having a driver in mainline at all.
Johannes Stezenbach has verified that the driver works on
AR8161, I have a AR8171 myself. The E2200 device ID I found
on github in somebody's repository.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tg3 code assumes the pci_error_handlers to be always called
in sequence. In particular, during ->error_detected(), NAPI is disabled
and the device is shutdown. The device is later reset and NAPI
re-enabled in ->slot_reset() and ->resume().
In EEH, if more than 6 errors are detected in a hour, only
->error_detected() will be called. This will leave the driver in an
inconsistent state as NAPI is disabled but netif_running state is still
true. When the device is later closed, we'll try to disable NAPI again
and it will loop forever.
We fix this by closing the device if we encounter any error conditions
during the normal sequence of the pci_error_handlers.
v2: Remove the changes in tg3_io_resume() based on Benjamin Poirier's
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should call __vlan_hwaccel_put_tag() only if the packet
comes from vlan, otherwise VLAN_TAG_PRESENT will always be
added.
Reported-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_clone fails if out of memory then just skip the fanout.
Problem was introduced in 3.10 with:
commit 6681712d67
Author: David Stevens <dlstevens@us.ibm.com>
Date: Fri Mar 15 04:35:51 2013 +0000
vxlan: generalize forwarding tables
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only migrate dynamic forwarding table entries, don't modify
static entries. If packet received from incorrect source IP address
assume it is an imposter and drop it.
This patch applies only to -net, a different patch would be needed for earlier
kernels since the NTF_SELF flag was introduced with 3.10.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a packet to arrive during vxlan_stop(), and
have a dynamic entry created. Close this by checking if device
is up.
CPU1 CPU2
vxlan_stop
vxlan_flush
hash_lock acquired
vxlan_encap_recv
vxlan_snoop
waiting for hash_lock
hash_lock relased
vxlan_flush done
hash_lock acquired
vxlan_fdb_create
This is a day-one bug in vxlan goes back to 3.7.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new device for this driver.
Reported-by: Tobias Kluge <zielscheibe@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Tobias Kluge <zielscheibe@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix ANI monitoring" reverted an earlier
commit that adjusted ANI to improve performance. But, this causes
adverse effects in AP mode (as reported by Felix based on an OpenWrt
report). Use the older INI/period configuration for now until more
testing is done.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Add custom parameters for CUS198" didn't
pass the correct gpio value to ath9k_hw_cfg_output(). Fix it.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to unset a previously-set multicast list (i.e. the new list
has 0 entries), mwifiex_set_multicast_list() was calling down to
mwifiex_request_set_multicast_list() while leaving
mcast_list.num_multicast_addr as an uninitialized value.
We were arriving at mwifiex_cmd_mac_multicast_adr() which would then
proceed to do an often huge memcpy of
mcast_list.num_multicast_addr*ETH_ALEN bytes, causing memory corruption
and hard to debug crashes.
Fix this by setting mcast_list.num_multicast_addr to 0 when no multicast
list is provided. Similarly, fix up the logic in
mwifiex_request_set_multicast_list() to unset the multicast list that
was previously sent to the hardware in such cases.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow a regulatory domain country code to be specified at boot
using a module argument. This overrides the firmware regulatory
mode.
This patch also enables uAP to operate in 11a mode with hostapd.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the firmware API has changed significantly and we don't
have support code for the old APIs, bump the version to be
able to release the version 7 API firmware. Unfortunately
this means that the driver in 3.9 and 3.10 can't work, but
that's still better than crashing the device/driver there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the commenting style consistent with networking block comment
style as suggested by checkpatch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Removing some boilerplate by using module_spi_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The fw_status wasn't zeroed during allocation, resulting
in uninitialized var usage, and finally causing AP
traffic stop after recovery.
The wrong value in fw_status_2->counters.tx_lnk_free_pkts
led to a bad lnk->allocated_pkts calculation in
wlcore_fw_status(), causing wl18xx_lnk_low_prio() to return
FALSE (lnk->allocated_pkts > thold).
This eventually blocked the link in wlcore_tx_work_locked(),
as wl1271_skb_dequeue() continuously returned NULL.
Fix it by zeroing wl->fw_status_1/2 during allocation.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Otherwise, if the work is pending, we might get
a bad dereference after the interface is removed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When associating to an AP with WEP set the
default key upon association by implementing
the set_deafult_key_idx op.
Fixes auto-arp sent with wrong key_idx bug.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In some R&D chips, the device may be left untrimmed and with the MAC
address missing from fuse ROM. In order to support those devices,
apply a random locally administered MAC address instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current code configures the peer caps only on BSS_CHANGED_HT
notification. However, we have to configure the peer caps
(and rates) even when HT is not enabled. Otherwise, the fw
continues working with low rates.
Configure the peer caps when sta_exists is true (i.e. when
we extracted the sta rates, e.g. on association).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of doing all the sysfs file handling in the main file, move it
to a new sysfs source file to reduce the amount of code in a single
file.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In PG2.0 there is an issue where PHY's FDSP Code RAM sometimes gets
corrupted when exiting from ELP mode. This issue is related to FDSP
Code RAM clock implementation.
PG2.1 introduces a HW fix for this issue that requires the driver to
change the FDSP Code Ram clock settings (mux it to ATGP clock instead
of its own clock).
This workaround uses PHY_FPGA_SPARE_1 register and is relevant to WL8
PG2.1 devices.
The fix is also backward compatible with older PG2.0 devices where the
register PHY_FPGA_SPARE_1 is not used and not connected.
The fix is done in the wl18xx_pre_upload function (must be performed
before uploading the FW code) and includes the following steps:
1. Disable FDSP clock
2. Set ATPG clock toward FDSP Code RAM rather than its own clock.
3. Re-enable FDSP clock
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When you copy some code, you are supposed to read it. If nothing else,
there's a chance to spot and fix an obvious bug instead of sharing it...
X-Song: "I Got It From Agnes", by Tom Lehrer
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Tom Lehrer? You're dating yourself, Al ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This utilize the new pinctrl core PM helpers to transition
the driver to "default" and "sleep" states.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This utilize the new pinctrl core PM helpers to transition
the driver to "default" and "sleep" states.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If "device is disconnected" check occurs to be true in ezusb_access_ltv(),
it just return -ENODEV. But that means request_context is leaked since
there are no any references to it anymore.
The patch adds a call to ezusb_request_context_put() before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.
Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201
Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to change the link state of VF (vPort)
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM6345 SoC Ethernet. BCM6345
has a slightly different and older DMA engine which requires the
following modifications:
- the width of the DMA channels on BCM6345 is 64 bytes vs 16 bytes,
which means that the helpers enet_dma{c,s} need to account for this
channel width and we can no longer use macros
- BCM6345 DMA engine does not have any internal SRAM for transfering
buffers
- BCM6345 buffer allocation and flow control is not per-channel but
global (done in RSET_ENETDMA)
- the DMA engine bits are right-shifted by 3 compared to other DMA
generations
- the DMA enable/interrupt masks are a little different (we need to
enabled more bits for 6345)
- some register have the same meaning but are offsetted in the ENET_DMAC
space so a lookup table is required to return the proper offset
The MAC itself is identical and requires no modifications to work.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tulip throws an error when dma debugging is enabled, as it doesn't properly
check dma mapping results with dma_mapping_error() durring tx ring refills.
Easy fix, just add it in, and drop the frame if the mapping is bad
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since raising/lowering the limits based on INI has
been changed, the error limit for OFDM has to be 1000,
not 3500.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new rate control API, the driver can now apply the
tx rate to outgoing frames just before they are uploaded to
the device. This is important because the rate control can
now react to fading or improving links a bit sooner.
Also, the driver no longer needs to sort the outgoing frames
for sample attempts (which affected the size of A-MPDUs and
the throughput of the link). For aggregated data frames, the
driver (and rate control) needs only to calculate and apply
a single set of tx rates to every subframe of the whole
aggregate.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initialization within brcmf_bus_start() fails on steps
before the brcmf_net_attach() the net_device for the primary
interface needs to be freed.
This patch resolves a panic during kernel boot as reported
by Stephen Warren.
ref.: http://mid.gmane.org/51AD1F22.2080004@wwwdotorg.org
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queue is unmapped while it was so loaded that
mac80211's was stopped, we need to wake the queue after
having freed all the packets in the queue.
Not doing so can result in weird stuff like:
* run lots of traffic (mac80211's queue gets stopped)
* RFKILL
* de-assert RFKILL
* no traffic
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a queue is disabled, it frees all its entries. Later,
the op_mode might still get notifications from the firmware
that triggers to free entries in the tx queue. The transport
should be prepared for these races and know to ignore
reclaim calls on queues that have been disabled and whose
entries have been freed.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fw is unreliable in all the cases in which the packet
wasn't sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The older devices (pre-7000/3000 series) all only work with the
DVM opmode due to firmware availability, while newer ones will
only work with the MVM opmode for the same reason.
When building a driver that only has one of MVM or DVM, there's
no reason to build the device support and have the PCIe IDs for
all devices since they can't be used anyway, so avoid that.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Give the scratch area a sub structure so it's marked
explicitly and it is obvious which part it is.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using #ifdef CONFIG_IWLWIFI_DEBUG, remove the
iwlwifi_mod_params.debug_level variable completely and
make iwl_have_debug_level() always return false in the
non-debug case. This way, the optimiser will elide all
code for it automatically without having to add #ifdefs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove calibration per-channel data as it's no longer used.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the unused iwl_mvm *mvm parameter from the
iwl_mvm_send_remote_wake_cfg function in D3.c.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to read the INTA register in the ICT IRQ
handler, this interrupt mechanism is designed to not have
to read as many registers as the regular one. Not reading
the INTA register gives a significant performance/CPU use
improvement.
Since we still want to get this info, fetch it only if
the ISR debug level is enabled.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes an issue that the driver increments the "RX length error"
on every buffer in sh_eth_rx() if the R8A7740.
This patch also adds a description about the Receive Frame Status bits.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the SoC specific support is no longer done with help of #ifdef'fery,
we no longer need '__maybe_unused' annotations to sh_eth_select_mii() and
sh_eth_set_duplex()...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems that don't need wake-on-lan may choose to power down the
chip on system standby. Upon resume, the power on causes the boot code
to startup and initialize the hardware. On one new platform, this is
causing the device to go into a bad state due to a race between the
driver and boot code, once every several hundred resumes. The same race
exists on open since we come up from a power on.
This patch adds a wait for boot code signature at the beginning of
tg3_init_hw() which is common to both cases. If there has not been a
power-off or the boot code has already completed, the signature will be
present and poll_fw() returns immediately. Also return immediately if
the device does not have firmware.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First the type of igmp_retrans (which is the actual counter of
igmp_resend parameter) is changed to u8 to be able to store values up
to 255 (as per documentation). There are two races that were hidden
there and which are easy to trigger after the previous fix, the first is
between bond_resend_igmp_join_requests and bond_change_active_slave
where igmp_retrans is set and can be altered by the periodic. The second
race condition is between multiple running instances of the periodic
(upon execution it can be scheduled again for immediate execution which
can cause the counter to go < 0 which in the unsigned case leads to
unnecessary igmp retransmissions).
Since in bond_change_active_slave bond->lock is held for reading and
curr_slave_lock for writing, we use curr_slave_lock for mutual
exclusion. We can't drop them as there're cases where RTNL is not held
when bond_change_active_slave is called. RCU is unlocked in
bond_resend_igmp_join_requests before getting curr_slave_lock since we
don't need it there and it's pointless to delay.
The decrement is moved inside the "if" block because if we decrement
unconditionally there's still a possibility for a race condition although
it is much more difficult to hit (many changes have to happen in
a very short period in order to trigger) which in the case of 3 parallel
running instances of this function and igmp_retrans == 1
(with check bond->igmp_retrans-- > 1) is:
f1 passes, doesn't re-schedule, but decrements - igmp_retrans = 0
f2 then passes, doesn't re-schedule, but decrements - igmp_retrans = 255
f3 does the unnecessary retransmissions.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bond device is supposed to get the first slave's MAC address and
the first enslavement fails then we need to reset the master's MAC
otherwise it will stay the same as the failed slave device. We do it
after err_undo_flags since that is the first place where the MAC can be
changed and we check if it should've been the first slave and if the
bond's MAC was set to it because that err place is used by multiple
locations prior to changing the master's MAC address.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c: In function:
stmmac_xmit drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1902:74:
error: expected ) before __func__
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to set the coherent DMA mask only if dma_set_mask() succeeded, and to
error out if either fails.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When putting vif-s on the rx notify list, calling xenvif_put() must be
deferred until after the removal from the list and the issuing of the
notification, as both operations dereference the pointer.
Changing this got me to notice that the "irq" variable was effectively
unused (and was of too narrow type anyway).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device::dev_id should not be used merely to indicate a VI index,
as it affects the way the local part of IPv6 addresses is normally
generated.
This field was intended for use where multiple devices may share a
single assigned MAC address and need to have different IPv6 addresses.
T4 VIs each have their own MAC address.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EINVAL on illegal flag instead of uninitialized value. This fixes the
kbuild test warning.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit df8ef8f3aa
"macvlan: add FDB bridge ops and macvlan flags"
added a way to control NOPROMISC macvlan flag through netlink.
However, with a non passthrough device we never set promisc on open,
even if NOPROMISC is off. As a result:
If userspace clears NOPROMISC on open, then does not clear it on a
netlink command, promisc counter is not decremented on stop and there
will be no way to clear it once macvlan is detached.
If userspace does not clear NOPROMISC on open, then sets NOPROMISC on a
netlink command, promisc counter will be decremented from 0 and overflow
to fffffffff with no way to clear promisc.
To fix, simply ignore NOPROMISC flag in a netlink command for
non-passthrough devices, same as we do at open/close.
Since we touch this code anyway - check dev_set_promiscuity return code
and pass it to users (though an error here is unlikely).
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This routine doesn't fail since 9fdc6bef (tuntap: dont use a private kmem_cache)
so it makes sense to compact the code a little bit.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TUN_PERSIST flag is not reported at all -- both TUNGETIFF, and sysfs
"flags" attribute skip one. Knowing whether a device is persistent or not
is critical for checkpoint-restore, thus I propose to add the read-only
IFF_PERSIST one for this.
Setting this new IFF_PERSIST is hardly possible, as TUNSETIFF doesn't check
for unknown flags being zero and thus there can be trash.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This pull request is intended for the 3.11 stream...
One big highlight is the cw1200 driver the ST-E CW1100 & CW1200
WLAN chipsets. This one has been lingering for a while, lacking
some review comments. Once started getting pulled into linux-next,
it got a bit more attention and a number of improvements were made
over the initial cut. No doubt there will be more changes ahead,
but I think it is looking alright at this point.
Along with that, there is the usual flurry of updates to the mac80211
core and the iwlwifi, mwifiex, ath9k, rt2x00, wil6210, and other
drivers. A few of the highlights are some rt2x00 refactoring/cleanup
by Gabor Juhos, some rt2800 hardware support enhancements by Stanislaw
Gruszka, some iwlwifi power management updates from Alexander Bondar,
some enhanced bcma SPROM support from Rafał Miłecki, and a variety
of other things here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9f86134155 (sh_eth: remove SH_ETH_HAS_TSU)
removes 'const' from 'sh_eth_netdev_ops' and modifies it in case TSU registers
are present. I've originally suggested to Iwamatsu-san to split this structure
in two instead and afterwards Dave M. suggested doing the same.
Split 'sh_eth_netdev_ops_tsu' from 'sh_eth_netdev_ops', making both 'const', and
assigning 'ndev->detdev_ops' depending on the presence of TSU registers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added statistics for flow-control and packets dropped by the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently firmware requested credits do not require fifo credits.
From a buffer management point of view this is incorrect. So
firwmware requested credits require also fifo credits before the
packet can be transferred to the host.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit dd9c46408f.
With "iwl{4965,3495): workaround for firmware frame tx rejection"
patches we can enable IEEE80211_HW_REPORTS_TX_ACK_STATUS again.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add functions that will stop/wake all queues. Make them safe
regarding multiple calls and when some ac are stopped/woke
independently.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enabels ath5k to use the new rate table to lookup each
mrr rate and retry information per packet.
Signed-off-by: Benjamin Vahl <bvahl@net.t-labs.tu-berlin.de>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commits,
"ath9k: Fix regression in channelwidth switch at the same channel"
"ath9k: Fix invalid noisefloor reading due to channel update"
attempted to fix noisefloor calibration when a channel switch
happens due to HT20/HT40 bandwidth change. This is causing invalid
readings resulting in messages like:
"ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX".
This results in an incorrect noise being used initially for reporting
the signal level of received packets, until NF calibration is done
and the history buffer is updated via the ANI timer, which happens
much later.
When a bandwidth change happens, it is appropriate to reset
the internal history data for the channel. Do this correctly in the
reset() routine by checking the "chanmode" variable.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9485 boards with XLNA, the default gpio config
is not set correctly, fix this.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
N-PHY and HT-PHY support is more or less stable and should be activated
by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When b43 gets build into the kernel and it should use bcma we have to
ensure that bcma was also build into the kernel and not as a module.
In this patch this is also done for SSB, although you can not
build b43 without ssb support for now.
This fixes a build problem reported by Randy Dunlap in
5187EB95.2060605@infradead.org
Reported-By: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All known ar7010+ar* device and current FW support STBC TX. This patch
make use of it and suggest to send STBC if peer support it.
I use wort "suggest" since currenly we have separate rate controller
in FW which will make decision based on rate and hardware.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WMI PCP Start flow should not be handled through:
net_device_ops->ndo_open()->wil_up()->__wil_up()
because it missing mandatory FW parameters (SSID,Channel,IEs, Security...).
Prior to AP starting __wil_up() may be called with iftype set
cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION)
depend on the application hostapd/wpa_supplicant/iw.
there should not be an attempt to start an AP flow,
AP/PCP start flow will be started latter by cfg80211_ops->start_ap().
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tracing in wil6210 is activated with WIL6210_TRACING and not with
ATH6KL_TRACING, this is used for the ath6kl driver. Rename the config
option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
at the vring initialisation, memory pool get allocated in the FW.
Make it 1-st because FW need this memory pool to precess
next commands
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No more need for special processing of EAPOL, FW can now send EAPOL frames
using normal Tx queue for TID 0
This fixes "schedule while atomic" bug - start_xmit called in softirq context;
while WMI mechanism that was used may sleep.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When starting secure AP, in some cases wpa_s provides probe template but not
probe/assoc IE's. In this case, derive missing IE's from probe.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report FC from the frame itself, as auxiliary information includes
only frame subtype. This is preparation for future changes, when
DMG beacon (extension frame) may be reported through wmi_evt_rx_mgmt()
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
map card's back-door debug data
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It may take up to 3500ms for the FW to start AP/PCP. Increase accordingly,
adding some safety margin.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CAB (Content after Beacon) queue is used for beacon-triggered
transmission of buffered multicast frames. If lots of multicast frames
were buffered and this queue fills up, it drowns out all regular
traffic. To limit the damage that buffered traffic can do, try to limit
the queued data to becaon_interval / 8.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for PS-Poll and U-APSD driver-buffered frames (part of
an aggregation session).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the UAPSD hardware queue to get PS-Poll responses out as fast as
possible and without backoff.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initialization within brcmf_bus_start() fails on steps
before the brcmf_net_attach() the net_device for the primary
interface needs to be freed.
This patch resolves a panic during kernel boot as reported
by Stephen Warren.
ref.: http://mid.gmane.org/51AD1F22.2080004@wwwdotorg.org
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When data is available and fw signalling is enabled then TIM
information should be sent to firmware. If it can piggy back
on existing packet then do that otherwise create dummy packet
to get information out.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_net_attach() the hard_header_len is set to sum of ETH_HLEN
and the headroom needed by the bus interface. Better use increment
instead as hard_header_len is already initialized upon alloc_netdev().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BDC header contains PropTx TLV signals that are useful to capture
for debugging. This event captures the header and tlv's in binary
form. This can be post-processed using trace-cmd plugin.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The statistic counter send_pkts was wrongly counted conditionally.
Correcting the mistake.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently suppressed packets get enque-ed with header which
then gets pulled before transmit. It is more logical and clean
to pull the header on return and push it unconditionally on xmit.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During P2P testing it turned out that the firmware sents multiple
multiple creditmap event messages. Only the first message from the
firmware should be processed. Otherwise the firmware-signalled flow
control can run haywire when it has packets outstanding in firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The destination entries for firmware-signalled flow control have
the interface id stored. This needs to be translated to bsscfg
index when looking up the ifp object for the interface.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of TDLS find the correct MAC descriptor for fw signalling
data. In case of TDLS each destination gets its own entry. This
was not handled correctly for P2P client.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When credit borrowing is active the BE credits have been depleted,
however the worker should still be scheduled. In case of credit
borrowing correct credit map to make sure worker remains active.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store gen bit on suppressed packet per entry and use latest
stored version for each packet which gets transmitted to fw.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently on a bus flow control both fws is informed and netif queue
gets closed. In case of fw signalling enabled, let the flow control
be handled by fw signalling only.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug logging in firmware-signalling code was rather extensive and
for a large part in the data path. This patch removes large part or the
level is changed to DATA level.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can request the driver for transmit packets using two different
signals. Only for one signal a flag was set in the sk_buff control
buffer. This patch adds explicit flag for the other signal as well.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reworked brcmf_skb_pick_up_credit() so it can be used for both
fcmode flavours in the same way.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On bus flow control (no more host bus resources to send packets
to device) the netif flow control was toggled, however credit
management should also take this status into account. Since there
are multiple sources handling this flow control necessary spinlocks
were added to protect flow control related data/states.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmf_skbuff_cb structure contain if_flags and htod fields. Both
have a bitfield defined to hold the fifo number. With a small code
change we get rid of the fifo bitfield in if_flags.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware-signal API specification defines length for the different
tlv. During testing on different devices it turned out not all firmware
used the tlv length according specification. Therefore the length check
is made less strict with this patch.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is exactly the same like the generic rt2800usb_ops.
Remove the duplicate and use the generic ops for all
devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The extra_tx_headroom field of struct rt2x00_ops
indicates the extra TX headroom size required for
a given device. This data is redundant, the value
can be computed from the desc_size and winfo_size
fields of the TX queues.
Move the extra_tx_headroom field to struct rt2x00_dev,
compute its value in the probe routine and use the
cached value in the rest of the code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds VHT80 support for the QCA world regulatory
domains.
Cc: kvalo@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to return a negative error code in the il3945_hw_set_hw_params() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch disables tx_amsdu support in mwifiex by default.
tx_amdsu support can be enabled via module parameter at load time.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PATCH "mwifiex: scan delay timer cleanup in unload path" adds code
to cancel scan delay timer in unload path. It causes a regression
for USB interface.
USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization.
It was observed that we are trying del_timer_sync() without setting
up the timer when remove handler is called after first enumeration.
This patch moves setup_timer() call to appropriate place so that
timer is setup for both the enumerations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the queue_init callback is implemented
by a driver it gets used instead of the
data_queue_desc based initialization.
The queue_init callback is implemented for
each drivers now, so the old initialization
method is not used anymore. Remove the unused
data_queue_desc structure and all of the
related code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
The actual chipset is already known when the callback
is used. This allows us to use a single callback for
all supported devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver uses static data structures for initializing
specific fields of a given data queue. These static
queue data descriptor structures are containing values
which related to a given chipset.
Even though the values are chip specific, the actual
selection of the used structure is based on device
specific vendor/product identifiers. This approach works,
but it is not always reliable. Sometimes the vendor and/or
device IDs of the PCI and USB devices contains improper
values which makes it impossible to select the correct
structure for such devices.
The patch adds a new callback to tr2x00_ops which
is called after the chipset detection is finished.
This allows the drivers to do dynamic initialization
of the data_queue structure for a given queue based
on the actual chipset.
After each driver implements the queue_init callback,
the data_queue_desc structure will be removed.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the queue->limit value instead of the
qdesc->entry_num to compute the threshold.
The two source values are the same and the
data queue descriptor structure will be
removed by a later patch.
Also separate the computation from the rest
of the init code to make further changes
easier.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon data queue is initialized already,
so fetch the number of the queue entries from
that instead of using the entry_num field of
the data queue descriptor.
The two values are the same, and the use of the
rt2x00dev->bcn->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qdesc parameter is not used anymore, so remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new field into struct data_queue and store
the size of the per-queue_entry private data in
that. Additionally, use the new field in the
rt2x00queue_alloc_entries function to compute
the size of the queue entries for a given queue.
The patch does not change the current behaviour
but makes it possible to remove the queue_desc
parameter of the rt2x00queue_alloc_entries function.
That will be done by a subsequent patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The phy error mask registers are programmed already
in ath9k_ani_restart(), so there is no need to set them
in ath9k_ani_reset().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
