If for whatever reasons pm_runtime_resume_and_get() fails and .remove() is
exited early, the i2c adapter stays around and the irq still calls its
handler, while the driver data and the register mapping go away. So if
later the i2c adapter is accessed or the irq triggers this results in
havoc accessing freed memory and unmapped registers.
So unregister the software resources even if resume failed, and only skip
the hardware access in that case.
Fixes: 588eb93ea4 ("i2c: imx: add runtime pm support to improve the performance")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Follow the advice of the below link and prefer 'strscpy'. Conversion is
easy because no driver used the return value and has been done with a
simple sed invocation.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Adds an ACPI companion to the KEMPLD I2C driver so that it correctly
detects any I2C devices nested under the KEMPLD's ACPI node (SBRG.CPLD).
This allows I2C devices attached to the KEMPLD I2C adapter to be declared
and instantiated via ACPI.
Signed-off-by: Chris Pringle <chris.pringle@phabrix.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8188 and added mt_i2c_regs_v3[], since
MT8188 i2c OFFSET_SLAVE_ADDR register changed from 0x04 to 0x94.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A late ack is currently being sent at the end of a transfer due to
incorrect logic in mchp_corei2c_empty_rx(). Currently the Assert Ack
bit is being written to the controller's control reg after the last
byte has been received, causing it to sent another byte with the ack.
Instead, the AA flag should be written to the control register when
the penultimate byte is read so it is sent out for the last byte.
Reported-by: Andreas Buerkler <andreas.buerkler@enclustra.com>
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Tested-by: Lewis Hanly <lewis.hanly@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[wsa: fixed typos in commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix i2c transfers using GPI DMA mode for all message types that do not set
the I2C_M_DMA_SAFE flag (e.g. SMBus "read byte").
In this case a bounce buffer is returned by i2c_get_dma_safe_msg_buf(),
and it has to synced back to the message after the transfer is done.
Add missing assignment of dma buffer in geni_i2c_gpi().
Set xferred in i2c_put_dma_safe_msg_buf() to true in case of no error to
ensure the sync-back of this dma buffer to the message.
Fixes: d8703554f4 ("i2c: qcom-geni: Add support for GPI DMA")
Signed-off-by: Robin Reckmann <robin.reckmann@gmail.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
Highlights:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop Studio
- thinkpad_acpi: AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
The following is an automated git shortlog grouped by driver:
ACPI:
- video: Fix acpi_video_handles_brightness_key_presses()
- video: Change how we determine if brightness key-presses are handled
Documentation/ABI:
- Add new attributes for mlxreg-io sysfs interfaces
- mlxreg-io: Fix contact info
Drop the PMC_ATOM Kconfig option:
- Drop the PMC_ATOM Kconfig option
EDAC, pnd2:
- convert to use common P2SB accessor
- Use proper I/O accessors and address space annotation
HID:
- surface-hid: Add support for hot-removal
ISST:
- PUNIT device mapping with Sub-NUMA clustering
Kconfig:
- Remove unnecessary "if X86"
MAINTAINERS:
- repair file entry in MICROSOFT SURFACE AGGREGATOR TABLET-MODE SWITCH
Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans:
- Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans
Move AMD platform drivers to separate directory:
- Move AMD platform drivers to separate directory
acer-wmi:
- Use backlight helper
acer_wmi:
- Cleanup Kconfig selects
apple-gmux:
- Use backlight helper
asus-wmi:
- Add mic-mute LED classdev support
- Add key mappings
compal-laptop:
- Use backlight helper
efi:
- Fix efi_power_off() not being run before acpi_power_off() when necessary
gigabyte-wmi:
- add support for B660I AORUS PRO DDR4
hp-wmi:
- Ignore Sanitization Mode event
i2c:
- i801: convert to use common P2SB accessor
ideapad-laptop:
- Add Ideapad 5 15ITL05 to ideapad_dytc_v4_allow_table[]
- Add allow_v4_dytc module parameter
intel/pmc:
- Add Alder Lake N support to PMC core driver
intel_atomisp2_led:
- Also turn off the always-on camera LED on the Asus T100TAF
leds:
- simatic-ipc-leds-gpio: Add GPIO version of Siemens driver
- simatic-ipc-leds: Convert to use P2SB accessor
mfd:
- lpc_ich: Add support for pinctrl in non-ACPI system
- lpc_ich: Switch to generic p2sb_bar()
- lpc_ich: Factor out lpc_ich_enable_spi_write()
mlx-platform:
- Add COME board revision register
- Add support for new system XH3000
- Introduce support for COMe NVSwitch management module for Vulcan chassis
- Add support for systems equipped with two ASICs
- Add cosmetic changes for alignment
- Make activation of some drivers conditional
p2sb:
- Move out of X86_PLATFORM_DEVICES dependency
panasonic-laptop:
- Use acpi_video_get_backlight_type()
- filter out duplicate volume up/down/mute keypresses
- don't report duplicate brightness key-presses
- revert "Resolve hotkey double trigger bug"
- sort includes alphabetically
- de-obfuscate button codes
pinctrl:
- intel: Check against matching data instead of ACPI companion
platform/mellanox:
- mlxreg-lc: Fix error flow and extend verbosity
- mlxreg-io: Add locking for io operations
- nvsw-sn2201: fix error code in nvsw_sn2201_create_static_devices()
platform/olpc:
- Fix uninitialized data in debugfs write
platform/surface:
- gpe: Add support for 13" Intel version of Surface Laptop 4
- tabletsw: Fix __le32 integer access
- Update copyright year of various drivers
- aggregator: Move subsystem hub drivers to their own module
- aggregator: Move device registry helper functions to core module
- aggregator_registry: Add support for tablet mode switch on Surface Laptop Studio
- aggregator_registry: Add support for tablet mode switch on Surface Pro 8
- Add KIP/POS tablet-mode switch driver
- aggregator: Add helper macros for requests with argument and return value
- aggregator: Reserve more event- and target-categories
- avoid flush_scheduled_work() usage
- aggregator_registry: Add support for keyboard cover on Surface Pro 8
- aggregator_registry: Add KIP device hub
- aggregator_registry: Change device ID for base hub
- aggregator_registry: Generify subsystem hub functionality
- aggregator: Add comment for KIP subsystem category
- aggregator_registry: Use client device wrappers for notifier registration
- aggregator: Allow notifiers to avoid communication on unregistering
- aggregator: Allow devices to be marked as hot-removed
- aggregator: Allow is_ssam_device() to be used when CONFIG_SURFACE_AGGREGATOR_BUS is disabled
platform/x86/amd/pmc:
- Add new platform support
- Add new acpi id for PMC controller
platform/x86/dell:
- Kconfig: Remove unnecessary "depends on X86_PLATFORM_DEVICES"
platform/x86/intel:
- Add Primary to Sideband (P2SB) bridge support
platform/x86/intel/ifs:
- Mark as BROKEN
platform/x86/intel/pmt:
- telemetry: Fix fixed region handling
platform/x86/intel/vsec:
- Fix wrong type for local status variables
- Add PCI error recovery support to Intel PMT
- Add support for Raptor Lake
- Rework early hardware code
pmc_atom:
- Fix comment typo
- Match all Lex BayTrail boards with critclk_systems DMI table
power/supply:
- surface_battery: Use client device wrappers for notifier registration
- surface_charger: Use client device wrappers for notifier registration
serial-multi-instantiate:
- Sort ACPI IDs by HID
- Get rid of redundant 'else'
- Use while (i--) pattern to clean up
- Improve dev_err_probe() messaging
- Drop duplicate check
- Improve autodetection
simatic-ipc:
- drop custom P2SB bar code
sony-laptop:
- Remove useless comparisons in sony_pic_read_possible_resource()
system76_acpi:
- Use dev_get_drvdata
thinkpad_acpi:
- Enable AMT by default on supported systems
- Add support for hotkey 0x131a
- Add support for automatic mode transitions
- profile capabilities as integer
- do not use PSC mode on Intel platforms
- Fix a memory leak of EFCH MMIO resource
- Replace custom str_on_off() etc
- Sort headers for better maintenance
- Use backlight helper
tools/power/x86/intel-speed-select:
- Remove unneeded semicolon
- Fix off by one check
watchdog:
- simatic-ipc-wdt: convert to use P2SB accessor
x86-android-tablets:
- Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmLrndEUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zeMgf7BjSCz6ZA8SSY1i8QHDTvdjySihHJ
j07Gn3j1T/5G00R/r6viMDE4PxcYvMAPXjq3azepKQd8H5kGfE323SA6fgWFPAvi
P2OvEfvWfI5S8FYGYPBkNP2MjQ5MFe7qzLEh3+wQH0ocJ7WRCi457B4Xvtd2gWI3
dHj5gMSWC3O5xNa2S4Mg3dnD9uJlwhX+FNjWIuRy8eh5+DikgByyC4B+uW6WtO5e
t0rmIm6q5wUzB7dIetJLoAQwrcpYAOkK7L33G9h/7knWAfiJfklaKTbftnoxbDSv
iGWODkLDyob4C48DmVusS6WMEhPUzl/R33+tk6LjVt/YOYOP030EMtCECQ==
=Krhc
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop
Studio
- thinkpad_acpi:
- AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
* tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (105 commits)
platform/x86/intel/vsec: Fix wrong type for local status variables
platform/x86: p2sb: Move out of X86_PLATFORM_DEVICES dependency
platform/x86: pmc_atom: Fix comment typo
platform/surface: gpe: Add support for 13" Intel version of Surface Laptop 4
platform/olpc: Fix uninitialized data in debugfs write
platform/mellanox: mlxreg-lc: Fix error flow and extend verbosity
platform/x86: pmc_atom: Match all Lex BayTrail boards with critclk_systems DMI table
platform/x86: sony-laptop: Remove useless comparisons in sony_pic_read_possible_resource()
tools/power/x86/intel-speed-select: Remove unneeded semicolon
tools/power/x86/intel-speed-select: Fix off by one check
platform/surface: tabletsw: Fix __le32 integer access
Documentation/ABI: Add new attributes for mlxreg-io sysfs interfaces
Documentation/ABI: mlxreg-io: Fix contact info
platform/mellanox: mlxreg-io: Add locking for io operations
platform/x86: mlx-platform: Add COME board revision register
platform/x86: mlx-platform: Add support for new system XH3000
platform/x86: mlx-platform: Introduce support for COMe NVSwitch management module for Vulcan chassis
platform/x86: mlx-platform: Add support for systems equipped with two ASICs
platform/x86: mlx-platform: Add cosmetic changes for alignment
platform/x86: mlx-platform: Make activation of some drivers conditional
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
- quite some DT schema conversions and extensions
- and a bunch of driver updates and improvements
-----BEGIN PGP SIGNATURE-----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=6fXH
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new drivers: Microchip CoreI2C, Renesas RZV2M
- quite some DT schema conversions and extensions
- and a bunch of driver updates and improvements
* tag 'i2c-for-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: extend documentation about retvals of master_xfer functions
i2c: mux-gpmux: Add of_node_put() when breaking out of loop
dt-bindings: i2c: i2c-rk3x: Document Rockchip RV1126
i2c: qcom-geni: Use the correct return value
i2c: cadence: Support PEC for SMBus block read
i2c: qcom-geni: Propagate GENI_ABORT_DONE to geni_i2c_abort_xfer()
i2c: brcmstb: Use dev_name() for adapter name
i2c: Add Renesas RZ/V2M controller
dt-bindings: i2c: Document RZ/V2M I2C controller
i2c: mlxcpld: Add callback to notify probing completion
i2c: scmi: Replace open coded device_get_match_data()
i2c: stm32: add support for the STM32MP13 soc
dt-bindings: i2c: st,stm32-i2c: add entry for stm32mp13
dt-bindings: i2c: i2c-rk3x: add rk3588 compatible
i2c: add support for microchip fpga i2c controllers
i2c: i801: Add support for Intel Meteor Lake-P
dt-bindings: i2c: nomadik: Add power domain to binding
dt-bindings: i2c: nomadik: Drop unused voltage supply from example
i2c: Fix a potential use after free
i2c: hisi: use HZ_PER_KHZ macro in units.h
...
The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management
to allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and
use the firmware interfaces for system power control and for
power capping.
-----BEGIN PGP SIGNATURE-----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=0dZI
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The introduction of GPI support moved things around and instead of
returning the result from geni_i2c_xfer() the number of messages in the
request was returned, ignoring the actual result. Fix this.
Fixes: d8703554f4 ("i2c: qcom-geni: Add support for GPI DMA")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Waiting for M_CMD_ABORT_EN in geni_i2c_abort_xfer() races with the
interrupt handler which will read and clear the abort bit, the result is
that every abort attempt takes 1 second and is followed by a message
about the abort having times out.
Introduce a new state variable to carry the abort_done state from the
interrupt handler back to geni_i2c_abort_xfer(). Also, turn NACK
and TIMEOUT errors into debug messages
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
[wsa: squashed two patches into one]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This make it easier to disambiguate the different i2c controllers
present in a system, and then correlating with /proc/interrupts allows
to know which instance is interrupt driven and which one is not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Yet another i2c controller from Renesas that is found on the RZ/V2M
(r9a09g011) SoC. It can support only 100kHz and 400KHz operation.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
[wsa: removed superfluous class type and renamed a function]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add notification to inform caller that driver probing has been
completed. It allows to user, invoked platform device registration for
"i2c-mlxcpld" driver, to be notified that bus adapter is available, and
thus some devices could be connected to this bus.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Problems were observed on the Xilinx ZynqMP platform with large I2C reads.
When a read of 277 bytes was performed, the controller NAKed the transfer
after only 252 bytes were transferred and returned an ENXIO error on the
transfer.
There is some code in cdns_i2c_master_isr to handle this case by resetting
the transfer count in the controller before it reaches 0, to allow larger
transfers to work, but it was conditional on the CDNS_I2C_BROKEN_HOLD_BIT
quirk being set on the controller, and ZynqMP uses the r1p14 version of
the core where this quirk is not being set. The requirement to do this to
support larger reads seems like an inherently required workaround due to
the core only having an 8-bit transfer size register, so it does not
appear that this should be conditional on the broken HOLD bit quirk which
is used elsewhere in the driver.
Remove the dependency on the CDNS_I2C_BROKEN_HOLD_BIT for this transfer
size reset logic to fix this problem.
Fixes: 63cab195bf ("i2c: removed work arounds in i2c driver for Zynq Ultrascale+ MPSoC")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace open coded device_get_match_data() in acpi_smbus_cmi_add().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add a new compatible for the stm32mp13. Fast Mode Plus control
register address differ from the one for STM32MP15.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
to provid --> to provide
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
-----BEGIN PGP SIGNATURE-----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=O/9g
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yTZT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoC drivers updatse for 5.20, please
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
* tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux:
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
phy: brcm-sata: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
i2c: brcmstb: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
ata: ahci_brcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
soc: bcm: bcm2835-power: Bypass power_on/off() calls
soc: bcm: bcm2835-power: Add support for BCM2711's RPiVid ASB
soc: bcm: bcm2835-power: Resolve ASB register macros
soc: bcm: bcm2835-power: Refactor ASB control
mfd: bcm2835-pm: Add support for BCM2711
mfd: bcm2835-pm: Use 'reg-names' to get resources
soc: bcm: brcmstb: biuctrl: Add missing of_node_put()
soc: bcm: brcmstb: pm: pm-arm: fix typo in comment
Link: https://lore.kernel.org/r/20220711164451.3542127-6-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
I2C_BRCMSTB depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch ensures that the clock notifier is unregistered
when driver probe is returning error.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Satish Nagireddy <satish.nagireddy@getcruise.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add Microchip CoreI2C i2c controller support. This driver supports the
"hard" i2c controller on the Microchip PolarFire SoC & the basic feature
set for "soft" i2c controller implemtations in the FPGA fabric.
Co-developed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add SMBus PCI ID on Intel Meteor Lake-P.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The recently added support for EFCH MMIO regions introduced a memory
leak in that code path. The leak is caused by the fact that
release_resource() merely removes the resource from the tree but does
not free its memory. We need to call release_mem_region() instead,
which does free the memory. As a nice side effect, this brings back
some symmetry between the legacy and MMIO paths.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Terry Bowman <terry.bowman@amd.com>
Tested-by: Terry Bowman <Terry.Bowman@amd.com>
Fixes: 7c148722d0 ("i2c: piix4: Add EFCH MMIO support to region request and release")
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch mpc5xxx_get_bus_frequency() to use fwnode in order to help
cleaning up other parts of the kernel from OF specific code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # for i2c-mpc
Acked-by: Wolfram Sang <wsa@kernel.org> # for the I2C part
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for mscan/mpc5xxx_can
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220507100147.5802-2-andriy.shevchenko@linux.intel.com
Free the adap structure only after we are done using it.
This patch just moves the put_device() down a bit to avoid the
use after free.
Fixes: 611e12ea0f ("i2c: core: manage i2c bus device refcount in i2c_[get|put]_adapter")
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
[wsa: added comment to the code, added Fixes tag]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
HZ macros has been centralized in units.h since [1]. Use it to avoid
duplicated definition.
[1] commit e2c77032fc ("units: add the HZ macros")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
MSM8974 CCI is the same as MSM8916 except it has two masters.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The clsk are prepared, enabled, then disabled. So if an error occurs after
the disable step, they are still prepared.
Add an error handling path to unprepare the clks in such a case, as already
done in the .remove function.
Fixes: 8b4fc246c3 ("i2c: mediatek: Optimize master_xfer() and avoid circular locking")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add an atomic_xfer method to the driver so that it behaves correctly
when controlling a PMIC that is responsible for device shutdown.
The atomic_xfer method added is similar to the one from the i2c-rk3x
driver. When running an atomic_xfer a bool flag in the driver data is
set, the interrupt is not unmasked on transfer start, and the IRQ
handler is manually invoked while waiting for pending transfers to
complete.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When I attempt to shut down (or reboot) my R8 based NTC CHIP with this
i2c driver I get the following error: "i2c i2c-0: mv64xxx: I2C bus
locked, block: 1, time_left: 0". Reboots are successful but shutdowns
freeze. If I comment out the shutdown routine the device both reboots
and shuts down successfully without receiving this error (however it
does receive a warning of missing atomic_xfer).
It appears that very few i2c drivers have a shutdown method, I assume
because these devices are often used to communicate with PMICs (such
as in my case with the R8 based NTC CHIP). I'm proposing we simply
remove this method so long as it doesn't cause trouble for others
downstream. I'll work on an atomic_xfer method and submit that in
a different patch.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the coverity warning
mixed_enum_type: enumerated type mixed with another type
We are passing an enum in the xiic_wakeup lets change
the function parameters to reflect that.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
[wsa: fixed $subject with proper prefix]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Even though the DW I2C controller reference clock source is requested by
the method devm_clk_get() with non-optional clock requirement the way the
clock handler is used afterwards has a pure optional clock semantic
(though in some circumstances we can get a warning about the clock missing
printed in the system console). There is no point in reimplementing that
functionality seeing the kernel clock framework already supports the
optional interface from scratch. Thus let's convert the platform driver to
using it.
Note by providing this commit we get to fix two problems. The first one
was introduced in commit c62ebb3d5f ("i2c: designware: Add support for
an interface clock"). It causes not having the interface clock (pclk)
enabled/disabled in case if the reference clock isn't provided. The second
problem was first introduced in commit b33af11de2 ("i2c: designware: Do
not require clock when SSCN and FFCN are provided"). Since that
modification the deferred probe procedure has been unsupported in case if
the interface clock isn't ready.
Fixes: c62ebb3d5f ("i2c: designware: Add support for an interface clock")
Fixes: b33af11de2 ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A remove callback that just returns 0 is equivalent to no callback at all
as can be seen in i2c_device_remove(). So simplify accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/i2c/busses/i2c-mxs.c:802:18: warning: cast to smaller integer type 'enum mxs_i2c_devtype' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: c32abd8b56 ("i2c: mxs: Remove unneeded platform_device_id")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Trivial non-functional change, which adds an alias to an extensively
used data location.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make the one-line comments capital in the driver to get the comment style
consistent.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add NPCM8XX I2C support.
The NPCM8XX uses a similar i2c module as NPCM7XX.
The internal HW FIFO is larger in NPCM8XX.
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Acked-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Correct the slave transaction logic to be compatible with the generic
slave backend driver.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
