New device suport
* ad7606
- Support the AD7616 16 channel, 12bit ADC.
* fxas21002c
- New driver for this gyroscope with I2C and SPI support.
* lsm6dsx
- Support the lsm6dsr, new device information structure and dt bindings.
* srf04
- Addition device IDs for mb1000, mb1010, mb1020, mb1030 and mb1040 +
support of different required trigger pulse lengths.
* st-accel
- Support the ls2de12, new device info and dt bindings.
* ti-ads8344
- New driver for this 8 channel, 16 bit SPI ADC.
Binding conversions to yaml - we have started doing these in general for IIO.
* avia-hx711
* bmp085
Cleanups and minor fixes / additions
* ad5758
- Fixup for some changes between preproduction parts and final part.
* ad7606
- Refactor handling of oversampling to make it easy to vary between
supported devices.
* ad9832
- Organise includes.
- Clock framework to handle clocks.
* ad9834
- Drop unnecessary parenthesis.
* bmc150
- Use __func__ rather than hardcoding.
* dummy_evgen.
- Fix a memleak on error in probe.
* kxcjk1013
- Add KXCJ91008 ACPI ID as seen in the wild.
- Use __func__ rather than hardcoding.
* imx7d
- Local dev variable to simplify code a bit.
- dev_err replaces pr_err to give more info.
- devm_platform_ioremap_resource for small reduction in boilerplate.
- Simplify probe and remove by sharing suspend / resume logic.
- Devm for iio_device_register as remove only contains the unregister.
* lsm6dsx
- Remove a variable that was never read.
- Open code values where they are effectively described by what is assigned
to them rather than using uninformative defines.
* max31856
- Avoid an unintialized ret variable in a path that can't actually occur
but is hard for a static checker to know.
* max9611
- White space
* mpu3050
- Reduce a sleep worst case by switching from msleep to usleep_range.
* qcom-spmi-adc5
- Add MODULE_DEVICE_TABLE to assist autoloading of this as a module.
* stm32-dfsdm
- Fix missing dependencies.
* stm32-timer trigger
- Fix a build issue when disabled.
* ti-ads7950
- Fix mising dependency on CONFIG_GPIOLIB.
-----BEGIN PGP SIGNATURE-----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=McKo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 5.2 cycle.
New device suport
* ad7606
- Support the AD7616 16 channel, 12bit ADC.
* fxas21002c
- New driver for this gyroscope with I2C and SPI support.
* lsm6dsx
- Support the lsm6dsr, new device information structure and dt bindings.
* srf04
- Addition device IDs for mb1000, mb1010, mb1020, mb1030 and mb1040 +
support of different required trigger pulse lengths.
* st-accel
- Support the ls2de12, new device info and dt bindings.
* ti-ads8344
- New driver for this 8 channel, 16 bit SPI ADC.
Binding conversions to yaml - we have started doing these in general for IIO.
* avia-hx711
* bmp085
Cleanups and minor fixes / additions
* ad5758
- Fixup for some changes between preproduction parts and final part.
* ad7606
- Refactor handling of oversampling to make it easy to vary between
supported devices.
* ad9832
- Organise includes.
- Clock framework to handle clocks.
* ad9834
- Drop unnecessary parenthesis.
* bmc150
- Use __func__ rather than hardcoding.
* dummy_evgen.
- Fix a memleak on error in probe.
* kxcjk1013
- Add KXCJ91008 ACPI ID as seen in the wild.
- Use __func__ rather than hardcoding.
* imx7d
- Local dev variable to simplify code a bit.
- dev_err replaces pr_err to give more info.
- devm_platform_ioremap_resource for small reduction in boilerplate.
- Simplify probe and remove by sharing suspend / resume logic.
- Devm for iio_device_register as remove only contains the unregister.
* lsm6dsx
- Remove a variable that was never read.
- Open code values where they are effectively described by what is assigned
to them rather than using uninformative defines.
* max31856
- Avoid an unintialized ret variable in a path that can't actually occur
but is hard for a static checker to know.
* max9611
- White space
* mpu3050
- Reduce a sleep worst case by switching from msleep to usleep_range.
* qcom-spmi-adc5
- Add MODULE_DEVICE_TABLE to assist autoloading of this as a module.
* stm32-dfsdm
- Fix missing dependencies.
* stm32-timer trigger
- Fix a build issue when disabled.
* ti-ads7950
- Fix mising dependency on CONFIG_GPIOLIB.
* tag 'iio-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (42 commits)
iio: adc: qcom-spmi-adc5: Fix of-based module autoloading
iio: dummy_evgen: fix possible memleak in evgen init
iio:accel:Switch hardcoded function name with a reference to __func__ making the code more maintainable
iio: adc: stm32-dfsdm: fix triggered buffer build dependency
iio: adc: stm32-dfsdm: fix unmet direct dependencies detected
iio: trigger: stm32-timer: fix build issue when disabled
iio: imx7d_adc: Use devm_iio_device_register()
iio: imx7d_adc: Simplify imx7d_adc_remove() with imx7d_adc_suspend()
iio: imx7d_adc: Simplify imx7d_adc_probe() with imx7d_adc_resume()
drivers/iio/gyro/mpu3050-core.c: This patch fix the following checkpatch warning.
iio: dac: ad5758: Modifications for new revision
iio: imu: st_lsm6dsx: inline per-sensor data
iio: adc: Add driver for the TI ADS8344 A/DC chips
dt-bindings: iio: adc: Add bindings for TI ADS8344 A/DC chips
MAINTAINERS: add entry for fxas21002c gyro driver
iio: gyro: fxas21002c: add spi driver
iio: gyro: fxas21002c: add i2c driver
iio: gyro: add core driver for fxas21002c
iio: gyro: add DT bindings to fxas21002c
Kconfig: change configuration of srf04 ultrasonic iio sensor
...
It fixes the following checkpatch.pl warning:
WARNING: Prefer using '"%s...", __func__' to using function's name, in a
string
Signed-off-by: Mohan Kumar <mohankumar718@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STMicroelectronics LIS2DE12 accelerometer in
st_accel framework.
http://www.st.com/resource/en/datasheet/lis2de12.pdf
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the ACPI ID for KXCJ9 sensor seen on the a Teclast X80 Power
tablet.
Signed-off-by: Valentin Manea <linux-iio@mrs.ro>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adopt the SPDX license identifier headers to ease license compliance
management. Also fix MODULE_LICENSE for cros_ec_accel_legacy to match
the SPDX and boiler plate license.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The cros_ec sensors drivers do not call any sysfs functions
or use any sysfs defines, and thus do not need to include
linux/sysfs.h. Also, some cros_ec drivers include linux/delay.h
and is not used.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
[remove linux/delay.h]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Formatting of Kconfig files doesn't look so pretty, so just
take damp cloth and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree support for kxcjk-1013 accelerometer sensors.
Signed-off-by: Robert Yang <decatf@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor some code in order to fix both the technical implementation
and the following warnings:
drivers/iio/accel/cros_ec_accel_legacy.c: In function ‘cros_ec_accel_legacy_probe’:
drivers/iio/accel/cros_ec_accel_legacy.c:387:36: warning: this statement may fall through [-Wimplicit-fallthrough=]
ec_accel_channels[X].scan_index = Y;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/iio/accel/cros_ec_accel_legacy.c:388:3: note: here
case Y:
^~~~
drivers/iio/accel/cros_ec_accel_legacy.c:389:36: warning: this statement may fall through [-Wimplicit-fallthrough=]
ec_accel_channels[Y].scan_index = X;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/iio/accel/cros_ec_accel_legacy.c:390:3: note: here
case Z:
^~~~
Notice that neither the for loop nor the switch statement is needed.
Also, "state->sign[Y] = 1" should be unconditional.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check that variable val is less than zero is redundant since val
is an unsigned int and hence can never be less than zero. Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently mount matrix is allowed in Device Tree, though there is
no technical issue to extend it to support ACPI.
Convert the function to use device_property_read_string_array() and
thus allow to read mount matrix from ACPI if available.
Example of use in _DSD method:
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mount-matrix", Package() {
"1", "0", "0",
"0", "0.866", "0.5",
"0", "-0.5", "0.866",
} },
}
})
At the same time drop the "of" prefix from its name and
convert current users.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/iio/accel/mma8452.c: In function ‘mma8452_probe’:
drivers/iio/accel/mma8452.c:1581:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret == data->chip_info->chip_id)
^
drivers/iio/accel/mma8452.c:1584:2: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On some laptops, kxcjk1013 is powered off when system enters S3. We need
restore the range regiter during resume. Otherwise, the sensor doesn't
work properly after S3.
Signed-off-by: he, bo <bo.he@intel.com>
Signed-off-by: Chen, Hu <hu1.chen@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Align broken line to match upper line parenthesis. Solves the
checkpatch.pl's message:
CHECK: Alignment should match open parenthesis
Signed-off-by: Luciana da Costa Marques <lucianadacostamarques@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Platform-specific ST accelerometer mount matrix information can be
provided by returning a package of 6 integers from the ACPI _ONT
method. This has been seen on Acer products such as Veriton Z4860G,
Z6860G and A890, which include a ST SMO8840 sensor. We have also
confirmed experimentally that the Windows driver uses such information.
The _ONT data format was explained by a ST vendor contact. However,
strangely enough, the _ONT transformations must be applied after first
applying another mount matrix which we determined experimentally. ST
have not commented on why this is the case, but we imagine that perhaps
earlier devices (before _ONT was introduced) required this translation
and hence it became 'standard.'
Interpret the _ONT data and export the equivalent mount matrix to
userspace.
If no _ONT data is present, no mount matrix is exported.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The accelerometer's power supply could be controllable on some
platforms, such as i.MX6Q-SABRESD board, the mma8451's power supplies
are controlled by a GPIO fixed regulator, need to make sure the
regulators are enabled before any communication with mma8451, this
patch adds vdd/vddio regulator operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
-----BEGIN PGP SIGNATURE-----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=+vyl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.21 cycle.
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
* tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (37 commits)
iio: adc: qcom-spmi-adc5: Initialize prescale properly
dt-bindings: iio: adc: exynos-adc: Add S5PV210 variant
iio: adc: Allow selection of Exynos ADC on S5PV210
iio: adc: exynos-adc: Add S5PV210 variant
iio: bmi160: use all devm functions in probe
iio: dac: ad5686: fix bit shift read register
iio:dac:ad5686: Add AD5310R support
Revert "Staging: iio: adt7316: Add an extra check for 'ret' equals to 0"
dt-bindings: iio: accel: use a generic node name for lis302
iio: core: check 'info' value before registering the device
staging: iio: adc: ad7280a: fix overwrite of the returned value
staging: iio: adc: ad7280a: check for devm_kasprint() failure
iio: humidity: hts221: add entry in MAINTAINERS file
iio: magnetometer: ak8975: Add the "AKM9911" ACPI HID
staging:iio:ad2s90: Move out of staging
staging:iio:ad2s90: Add comment to device state mutex
staging:iio:ad2s90: Replace license text w/ SPDX identifier
dt-bindings:iio:resolver: Add docs for ad2s90
staging:iio:ad2s90: Add max frequency check at probe
staging:iio:ad2s90: Remove spi setup that should be done via dt
...
Various 2-in-1's use KIOX010A and KIOX020A as HIDs for 2 KXCJ91008
accelerometers. The KIOX010A HID is for the one in the base and the
KIOX020A for the accelerometer in the keyboard.
Since userspace does not have a way yet to deal with (or ignore) the
accelerometer in the keyboard, this commit just adds the KIOX010A HID
for now so that display rotation will work.
Related: https://github.com/hadess/iio-sensor-proxy/issues/166
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This HID is used on the ASUS MeMO Pad 7 (ME176C) tablet.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit add support for STMicroelectronics lis3de accelerometer.
Datasheet for this device can be found here:
https://www.st.com/resource/en/datasheet/lis3de.pdf
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add KIOX0009 ACPI HID, this is used e.g. on the Acer One 10.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adxl372 is designed to communicate in either SPI or I2C protocol. It
autodetects the format being used, requiring no configuration control to
select the format.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch restructures the existing adxl372 driver by adding a module for
SPI and a header file, while the baseline module deals with the chip-logic.
This is a necessary step, as this driver should support in the future
a similar device which differs only in the type of interface used (I2C
instead of SPI).
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the option for the user to select the filter bandwidth. The
user can also read the available bandwidths which are always adjusted to be
at most half of the sampling frequency. Furthermore, the currently selected
bandwidth can be read via the read_raw function, while the write_raw sets a
new bandwidth value.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the option for the user to select the sampling frequency.
Also, the user can read the available frequencies and read the currently
set frequency via the read_raw function. The frequency can be set via the
write_raw function.
When the frequency is set, the bandwidth is also checked and ensured
that it is constrained to at most half of the sampling frequency. Also, the
activity and inactivity timers have to be updated because they depend on
the selected ODR.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch provides a validate_device callback for the trigger which makes
sure that other devices are rejected.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes ef89f4b96a ("iio: adxl345: Add support for the ADXL375").
This was found via static checker.
After looking into the code a bit, it's unlikely that there will be a NULL
dereference if the `id` object in that specific code path.
However, it's safe to add a NULL (paranoid) check just to make sure and
remove any uncertainties.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for the adxl372 FIFO. In order to accomplish this,
triggered buffers were used.
The number of FIFO samples which trigger the watermark interrupt can be
configured by using the buffer watermark. The FIFO format is determined by
configuring the scan elements for each axis. The FIFO data is pushed to the
IIO device's buffer.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds basic support for Analog Devices ADXL372 SPI-Bus
Three-Axis Digital Accelerometer.
The device is probed and configured the with some initial default
values. With this basic driver, it is possible to read raw acceleration
data.
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL372.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are also a couple of fixes that can wait for the coming merge
window.
Core new features
* Support for phase channels (used in time of flight sensors amongst
other things)
* Support for deep UV light channel modifier.
New Device Support
* AD4758 DAC
- New driver and dt bindings.
* adxl345
- Support the adxl375 +-200g part which is register compatible.
* isl29501 Time of flight sensor.
- New driver
* meson-saradc
- Support the Meson8m2 Socs - right now this is just an ID, but there will
be additional difference in future.
* mpu6050
- New ID for 6515 variant.
* si1133 UV sensor.
- New driver
* Spreadtrum SC27xx PMIC ADC
- New driver and dt bindings.
Features
* adxl345
- Add calibration offset readback and writing.
- Add sampling frequency control.
Fixes and Cleanups
* ad5933
- Use a macro for the channel definition to reduce duplication.
* ad9523
- Replace use of core mlock with a local lock. Part of ongoing efforts
to avoid confusing the purpose of mlock which is only about iio core
state changes.
- Fix displayed phase which was out by a factor of 10.
* adxl345
- Add a link to the datasheet.
- Rework the use of the address field in the chan_spec structures to
allow addition of more per channel information.
* adis imu
- Mark switch fall throughs.
* at91-sama5d2
- Fix some casting on big endian systems.
* bmp280
- Drop some DT elements that aren't used and should mostly be done from
userspace rather than in DT.
* hx711
- add clock-frequency dt binding and resulting delay to deal with capacitance
issue on some boards.
- fix a spurious unit-address in the example.
* ina2xx
- Avoid a possible kthread_stop with a stale task_struct.
* ltc2632
- Remove some unused local variables (assigned but value never used).
* max1363
- Use device_get_match_data to remove some boilerplate.
* mma8452
- Mark switch fall throughs.
* sca3000
- Fix a missing return in a switch statement (a bad fallthrough
previously!)
* sigma-delta-modulator
- Drop incorrect unit address from the DT example.
* st_accel
- Use device_get_match_data to drop some boiler plate.
- Move to probe_new for i2c driver as second parameter not used.
* st_sensors library
- Use a strlcpy (safe in this case).
* st_lsm6dsx
- Add some error logging.
* ti-ads7950
- SPDX
- Allow simultaneous buffered and polled reads. Needed on a Lego Mindstorms
EV3 where some channels are used for power supply monitoring at a very low
rate.
* ti-dac5571
- Remove an unused variable.
* xadc
- Drop some dead code.
-----BEGIN PGP SIGNATURE-----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=T+hS
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.19b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups.
There are also a couple of fixes that can wait for the coming merge
window.
Core new features
* Support for phase channels (used in time of flight sensors amongst
other things)
* Support for deep UV light channel modifier.
New Device Support
* AD4758 DAC
- New driver and dt bindings.
* adxl345
- Support the adxl375 +-200g part which is register compatible.
* isl29501 Time of flight sensor.
- New driver
* meson-saradc
- Support the Meson8m2 Socs - right now this is just an ID, but there will
be additional difference in future.
* mpu6050
- New ID for 6515 variant.
* si1133 UV sensor.
- New driver
* Spreadtrum SC27xx PMIC ADC
- New driver and dt bindings.
Features
* adxl345
- Add calibration offset readback and writing.
- Add sampling frequency control.
Fixes and Cleanups
* ad5933
- Use a macro for the channel definition to reduce duplication.
* ad9523
- Replace use of core mlock with a local lock. Part of ongoing efforts
to avoid confusing the purpose of mlock which is only about iio core
state changes.
- Fix displayed phase which was out by a factor of 10.
* adxl345
- Add a link to the datasheet.
- Rework the use of the address field in the chan_spec structures to
allow addition of more per channel information.
* adis imu
- Mark switch fall throughs.
* at91-sama5d2
- Fix some casting on big endian systems.
* bmp280
- Drop some DT elements that aren't used and should mostly be done from
userspace rather than in DT.
* hx711
- add clock-frequency dt binding and resulting delay to deal with capacitance
issue on some boards.
- fix a spurious unit-address in the example.
* ina2xx
- Avoid a possible kthread_stop with a stale task_struct.
* ltc2632
- Remove some unused local variables (assigned but value never used).
* max1363
- Use device_get_match_data to remove some boilerplate.
* mma8452
- Mark switch fall throughs.
* sca3000
- Fix a missing return in a switch statement (a bad fallthrough
previously!)
* sigma-delta-modulator
- Drop incorrect unit address from the DT example.
* st_accel
- Use device_get_match_data to drop some boiler plate.
- Move to probe_new for i2c driver as second parameter not used.
* st_sensors library
- Use a strlcpy (safe in this case).
* st_lsm6dsx
- Add some error logging.
* ti-ads7950
- SPDX
- Allow simultaneous buffered and polled reads. Needed on a Lego Mindstorms
EV3 where some channels are used for power supply monitoring at a very low
rate.
* ti-dac5571
- Remove an unused variable.
* xadc
- Drop some dead code.
The IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY case is missing a
return and will fall through to the default case and errorenously
return -EINVAL.
Fix this by adding in missing *return ret*.
Fixes: 626f971b5b ("staging:iio:accel:sca3000 Add write support to the low pass filter control")
Reported-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADXL375 is fully register map compatible to the ADXL345 (including the
device ID register returning the same value ...).
The only difference is the resolution of the acceleration sensor. The
ADXL375 can measure up to +-200g of acceleration.
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL375.PDF
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADXL345 provides selectable output data rate. This adds the iio
channel information for the sampling frequency with that feature.
Cc: Eva Rachel Retuya <eraretuya@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used in this case: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
struct i2c_device_id argument of probe() is not used, so use probe_new()
instead.
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device_get_match_data API to simplify access to driver data.
Let acpi_device_id table entries point to the same driver data as
of_device_id table entries and uniquify access to driver data by using
device_get_match_data API. Remove unused i2c_device_id .driver_data
fields.
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADXL345 provides the offset adjustment registers for each axis.
This adds the iio channel information for the calibraion offsets with
that feature.
Cc: Eva Rachel Retuya <eraretuya@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the address field in iio_chan_spec is filled with an accel
data register address for the corresponding axis.
In preparation for adding calibration offset support, this sets the
address field to the index of accel data registers instead of the actual
register address.
This change makes it easier to access both accel registers and
calibration offset registers with fewer lines of code as these are
located in X-axis, Y-axis, Z-axis order.
Cc: Eva Rachel Retuya <eraretuya@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a link to the ADXL345 datasheet
Cc: Eva Rachel Retuya <eraretuya@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Interrupts are ignored if no event bit is set in the status status
register and this breaks the buffer interface. No data is shown when
running "iio_generic_buffer -n mma8451 -a" and interrupt counts go
crazy.
Fix by not returning IRQ_NONE if DRDY is set.
Fixes: 605f72de13 ("iio: accel: mma8452: improvements to handle
multiple events")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Modified the sleep method when data is not ready to allow for sampling > 50sps to work.
Signed-off-by: Richard Tresidder <rtresidd@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
-----BEGIN PGP SIGNATURE-----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=egCX
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st round of IIO new device support, features and cleanup for the 4.18 cycle
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
The regmap core now handles splitting up transactions according to
max_raw_read, so this code is no longer required in client drivers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Lenovo Ideapad Miix 320 uses an st accelerometer with an ACPI id
of SMO8840, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'sca3000_configure_ring()' can fail, so test its return value and
propagate it if needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
