Commit graph

74 commits

Author SHA1 Message Date
Mikael Pettersson
a2342f4643 sata_promise: don't classify overruns as HSM errors
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.

Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.

This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.

This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-12 14:33:07 -05:00
Mikael Pettersson
ff7cddf59e sata_promise: update reset code
sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.

This patch thus updates the reset code to more closely
match the reference driver:

- soft reset (pdc_reset_port):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * write reset bit in PDC_CTLSTAT before the first read
    in the loop
  * for 2nd gen SATA follow up with FPDMA reset and clearing
    error status registers
- hard reset (pdc_sata_hardreset):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * reset ATA engine via the PCI control register
  * Tejun's change to use non-waiting hardreset + follow-up SRST

I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).

Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-17 16:46:34 -04:00
Mikael Pettersson
0ae6654da4 sata_promise: disable hotplug on 1st gen chips
1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.

The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.

Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-17 16:46:12 -04:00
Alan Cox
c96f1732e2 [libata] Improve timeout handling
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.

[Revised to exclude the timeout handling on a few devices that inherit from
 SFF but are not SFF enough to use the default timeout handler]

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:52:39 -04:00
Erik Inge Bolsø
14bdef982c [libata] convert drivers to use ata.h mode mask defines
No functional changes in this patch.

Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:13:27 -04:00
Mikael Pettersson
cadef677e4 sata_promise: add ATA engine reset to reset ops
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.

The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.

To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:03 -05:00
Tejun Heo
82ef04fb4c libata: make SCR access ops per-link
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link.  However, that assumption won't hold anymore with the scheduled
addition of slave link.

Make SCR access ops per-link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:28 -04:00
Mikael Pettersson
7715a6f9cd sata_promise: other cleanups
Minor coding-style fixes for sata_promise:
- remove stray blank lines
- fix checkpatch.pl errors; warnings about long lines
  remain, but I don't intend to address those at this time
- remove two inline directives: neither is essential and
  both functions are trivially inlinable anyway by virtue
  of being static and having a single unique call site
- fix comment in pdc_interrupt(): the bits in PDC_INT_SEQMASK
  denote SEQIDs not tags, the distinction becomes important
  when NCQ gets implemented

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:31:34 -04:00
Mikael Pettersson
821d22cdcd sata_promise: mmio access cleanups
This patch cleans up sata_promise's mmio accesses.

In sata_promise there are three distinct mmio address spaces:
1. global registers, offsets from host->iomap[PDC_MMIO_BAR]
2. per-port ATA registers, offsets from ap->ioaddr.cmd_addr
3. per-port SATA registers, offsets from ap->ioaddr.scr_addr

The driver currently often fails to indicate which address space
a given mmio base pointer refers to, which is a source of bugs
and confusion (see recent pdc_thaw() irq clearing bug; it's also
been an obstacle for the pending NCQ extensions).

To reduce these problems, adopt a coding style where the name of
a base pointer always indicates which address space it refers to:
1. global registers: host_mmio
2. per-port ATA registers: ata_mmio
3. per-port SATA registers: sata_mmio

Also rearrange register offset definitions to clearly indicate
which address space they belong to, and add a symbolic definition
for the previously hard-coded PHYMODE4 register.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:31:26 -04:00
Mikael Pettersson
a13db78e22 sata_promise: fix irq clearing buglets
This patch fixes two bugs in sata_promise's irq status clearing paths:
1. When clearing the irq status for a specific port, the driver
   read the global SEQMASK register. This is wrong because that
   clears the irq status for _all_ ports.
2. pdc_thaw() incorrectly added the PDC_INT_SEQMASK host register
   offset to a per-port ata engine base address. This resulted in
   it reading the unrelated PDC_PKT_SUBMIT register, which did not
   have the desired irq status clearing effect.

In both cases the fix is to read from the port's Command/Status
register. This also matches what Promise's own driver does.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:30:47 -04:00
Tejun Heo
5682ed33aa libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
9363c3825e libata: rename SFF functions
SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:21 -04:00
Al Viro
826cd156de libata annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
a1efdaba2d libata: make reset related methods proper port operations
Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:18 -04:00
Tejun Heo
029cfd6b74 libata: implement and use ops inheritance
libata lets low level drivers build ata_port_operations table and
register it with libata core layer.  This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.

This becomes worse for drivers which support related similar
controllers which differ slightly.  They share most of the operations
except for a few.  However, the driver still needs to list all
operations for each variant.  This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.

This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone.  When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time.  Some of those inconsistencies
cause immediate problems and fixed.  Others just remain there dormant
making maintenance increasingly difficult.

To rectify the problem, this patch implements ata_port_operations
inheritance.  To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance.  An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop.  When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified.  This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.

libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma.  To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.

After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to.  The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.

* sata_sx4 is still using old style EH and currently doesn't take
  advantage of ops inheritance.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
68d1d07b51 libata: implement and use SHT initializers
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer.  This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.

This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht.  Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.

All sht tables are identical before and after this patch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Mikael Pettersson
c07a9c4995 sata_promise: fix hardreset hotplug events, take 2
A Promise SATA controller will signal hotplug events when a hard
reset (COMRESET) is done on a port. These events aren't masked by
the driver, and the unexpected interrupts will cause a sequence
of failed reset attempts util libata's EH finally gives up.

This has not been a common problem so far, but the pending libata
hardreset-by-default changes makes it a critical issue.

The solution is to disable hotplug events before a reset, and to
reenable them afterwards. (Promise's driver does this too.)

This patch adds SATA-specific versions of ->freeze() and ->thaw()
that also disable and enable hotplug events. PATA ports continue
to use the old versions of ->freeze() and ->thaw().

Accesses to the hotplug register must be serialised via host->lock.
We rely on ap->lock == &ap->host->lock and that libata takes this
lock before ->freeze() and ->thaw(). Document this requirement.
The interrupt handler is adjusted so its hotplug register accesses
are inside the region protected by host->lock.

Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4,
FastTrack TX4000) with various combinations of SATA and PATA disks,
with and without the pending hardreset-by-default changes.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-24 22:31:25 -04:00
Harvey Harrison
6903c0f7ef ata: fix sparse warning in sata_promise.c
drivers/ata/sata_promise.c:546:15: warning: symbol 'len' shadows an earlier one
drivers/ata/sata_promise.c:538:6: originally declared here

len is set again immediately after the loop, so this is safe.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:50:59 -05:00
Tejun Heo
ff2aeb1eb6 libata: convert to chained sg
libata used private sg iterator to handle padding sg.  Now that sg can
be chained, padding can be handled using standard sg ops.  Convert to
chained sg.

* s/qc->__sg/qc->sg/

* s/qc->pad_sgent/qc->extra_sg[]/.  Because chaining consumes one sg
  entry.  There need to be two extra sg entries.  The renaming is also
  for future addition of other extra sg entries.

* Padding setup is moved into ata_sg_setup_extra() which is organized
  in a way that future addition of other extra sg entries is easy.

* qc->orig_n_elem is unused and removed.

* qc->n_elem now contains the number of sg entries that LLDs should
  map.  qc->mapped_n_elem is added to carry the original number of
  mapped sgs for unmapping.

* The last sg of the original sg list is used to chain to extra sg
  list.  The original last sg is pointed to by qc->last_sg and the
  content is stored in qc->saved_last_sg.  It's restored during
  ata_sg_clean().

* All sg walking code has been updated.  Unnecessary assertions and
  checks for conditions the core layer already guarantees are removed.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:14 -05:00
Tejun Heo
0dc36888d4 libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion.  Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:14 -05:00
Tejun Heo
46a671430d sata_promise: make pdc_atapi_pkt() use values from qc->tf
Make pdc_atapi_pkt() use values from qc->tf instead of creating its
own.  This is to ease future ATAPI handling changes.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:12 -05:00
Mikael Pettersson
03116d67e0 sata_promise: fix endianess bug in ASIC PRD bug workaround
The original workaround for the Promise ASIC PRD bug
contained an endianess bug which I failed to detect:
the adjustment of the last PRD entry's length field
applied host arithmetic to little-endian data, which
is incorrect on big-endian machines.

We have the length available in host-endian format, so
do the adjustment on host-endian data and then convert
and store it in the PRD entry's little-endian data field.

Thanks to an anonymous reviewer for detecting this bug.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-03 08:46:54 -04:00
Mikael Pettersson
5595ddf98c sata_promise: cleanups
Minor sata_promise cleanups:
- use C99 array initialisers in pdc_port_info[]
- add myself in the file head's Maintained by note,
  since users don't always read the MAINTAINERS file
- SG/PRD bug workaround warrants driver version bump

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
 drivers/ata/sata_promise.c |   17 +++++++++--------
 1 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-30 09:27:57 -04:00
Mikael Pettersson
b9ccd4a90b sata_promise: ASIC PRD table bug workaround, take 2
Second-generation Promise SATA controllers have an ASIC bug
which can trigger if the last PRD entry is larger than 164 bytes,
resulting in intermittent errors and possible data corruption.

Work around this by replacing calls to ata_qc_prep() with a
private version that fills the PRD, checks the size of the
last entry, and if necessary splits it to avoid the bug.
Also reduce sg_tablesize by 1 to accommodate the new entry.

Tested on the second-generation SATA300 TX4 and SATA300 TX2plus,
and the first-generation PDC20378.

Thanks to Alexander Sabourenkov for verifying the bug by
studying the vendor driver, and for writing the initial patch
upon which this one is based.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
Changes since previous version:
* use new PDC_MAX_PRD constant to initialise sg_tablesize

 drivers/ata/sata_promise.c |   87 ++++++++++++++++++++++++++++++++++++++++++---
 1 files changed, 83 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-30 09:27:57 -04:00
Jeff Garzik
5796d1c4c8 [libata] Address some checkpatch-spotted issues
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 06:15:27 -04:00
Tejun Heo
cbcdd87593 libata: implement and use ata_port_desc() to report port configuration
Currently, port configuration reporting has the following problems.

* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
  non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.

This patch implements and uses ata_port_desc() and
ata_port_pbar_desc().  ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ".  ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.

LLD pushes whatever description it wants using the above two
functions.  The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".

SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions.  In many cases,
such controllers need to report different things anyway.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:37 -04:00
Jeff Garzik
ac8869d56d [libata] Remove ->port_disable() hook
It was always set to ata_port_disable().  Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:35 -04:00
Jeff Garzik
6d32d30f55 [libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()
* ->irq_ack() is redundant to what the irq handler already
  performs... chk-status + irq-clear.  Furthermore, it is only
  called in one place, when screaming-irq-debugging is enabled,
  so we don't want to bother with a hook just for that.

* ata_dummy_irq_on() is only ever used in drivers that have
  no callpath reaching ->irq_on().  Remove .irq_on hook from
  those drivers, and the now-unused ata_dummy_irq_on()

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:34 -04:00
Tejun Heo
936fd73286 libata-link: linkify PHY-related functions
Make the following PHY-related functions to deal with ata_link instead
of ata_port.

* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Tejun Heo
9af5c9c97d libata-link: introduce ata_link
Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Mikael Pettersson
7f9992a231 sata_promise: FastTrack TX4200 is a second-generation chip
This patch corrects sata_promise to classify FastTrack TX4200
(DID 3515/3519) as a second-generation chip. Promise's partial-
source FT TX4200 driver confirms this classification.

Treating it as a first-generation chip causes several problems:
1. Detection failures. This is a recent regression triggered by
   the hotplug-enabling changes in 2.6.23-rc1.
2. Various "failed to resume link for reset" warnings.

This patch fixes <http://bugzilla.kernel.org/show_bug.cgi?id=8936>.

Thanks to Stephen Ziemba for reporting the bug and for testing the fix.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Stephen Ziemba <sziemba@ecn.purdue.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-31 04:14:44 -04:00
Tejun Heo
da3dbb17a0 libata: make ->scr_read/write callbacks return error code
Convert ->scr_read/write callbacks to return error code to better
indicate failure.  This will help handling of SCR_NOTIFICATION.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20 08:02:11 -04:00
Mikael Pettersson
a77720ad0a sata_promise: SATA hotplug support, take 2
This patch enables hotplugging of SATA devices in the
sata_promise driver. It's been tested successfully on
both first- and second-generation Promise SATA chips:
SATA150 TX2plus, SATAII150 TX2plus, SATAII150 TX4,
SATA300 TX2plus, and SATA300 TX4.

The only quirk I've seen is that hotplugging (insertion)
on the first-generation SATA150 TX2plus requires a lengthier
EH sequence than on the second-generation chips.
On the second-generation chips a simple soft reset seems
to suffice, but on the first-generation chip there's a
"port is slow to respond" after the initial soft reset,
after which libata issues a hard reset, and then the
device is recognised.

The hotplug checks are high up in the interrupt handling
path, not deep down in error_intr as in ahci/sata_sil24.
That's because the chip doesn't signal hotplug status changes
in the per-port status register: instead a global register
contains hotplug control and status flags for all ports.
I considered following the ahci/sata_sil24 structure, but
that would have required non-trivial changes to the interrupt
handling path, so I chose to keep the hotplug changes simple
and unobtrusive.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
This patch depends on the "sata_promise: cleanups" patch.

Changes since the previous version (posted June 19):
- Correct pdc_interrupt() to increment 'handled' also in
  the hotplug case. This prevents IRQ_NONE from being
  returned when an interrupt only has hotplug events to
  handle, which could confuse the kernel's IRQ machinery.
- Added testing on the SATAII150 TX4.

 drivers/ata/sata_promise.c |   41 ++++++++++++++++++++++++++++++++++++-----
 1 files changed, 36 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 21:14:19 -04:00
Jeff Garzik
469248abf0 [libata] Clean up driver udma_mask initializers
* Use ATA_UDMA*
* Remove FIXME notations that once served to remind us to verify
  that these were indeed the correct UDMA masks.  They are.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09 12:17:35 -04:00
Mikael Pettersson
d0e580316e sata_promise: cleanups
This patch applies some trivial cleanups to sata_promise:
- repair whitespace damage
- correct comment at board_2057x_pata definition
- pull SATAII TX4 support code out to separate functions
- rename ata_nr to ata_no for consistency with libata's port_no
- remove some init-time debug printks (requested by Jeff)

This patch should cause no behavioural changes, except for
the removed printks.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
 drivers/ata/sata_promise.c |   56 ++++++++++++++++++---------------------------
 1 files changed, 23 insertions(+), 33 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09 12:17:34 -04:00
Jeff Garzik
59f998802b [libata] drivers: remove 'void __iomem *' casts from pre-iomap days
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09 12:17:32 -04:00
Tejun Heo
51b94d2a5a sata_promise: use TF interface for polling NODATA commands
sata_promise uses two different command modes - packet and TF.  Packet mode
is intelligent low-overhead mode while TF is the same old taskfile
interface.  As with other advanced interface (ahci/sil24),
ATA_TFLAG_POLLING has no effect in packet mode.  However, PIO commands are
issued using TF interface in polling mode, so pdc_interrupt() considers
interrupts spurious if ATA_TFLAG_POLLING is set.

This is broken for polling NODATA commands because command is issued using
packet mode but the interrupt handler ignores it due to ATA_TFLAG_POLLING.
Fix pdc_qc_issue_prot() such that ATA/ATAPI NODATA commands are issued
using TF interface if ATA_TFLAG_POLLING is set.

This patch fixes detection failure introduced by polling SETXFERMODE.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-06-08 17:23:33 -07:00
Jeff Garzik
bb31223593 [libata] sata_promise: fix flags typo
A stray comma makes all the difference.  Change to '|' as these flags
should be or'd together.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-24 23:35:59 -04:00
Mikael Pettersson
5ac2fe5756 sata_promise: SATAII-150/300 TX4 port numbering fix
There is a known problem with sata_promise on SATAII-150/300 TX4
controller cards: it enumerates drives in an order that differs
from the port numbers printed on the controller cards. However,
Promise's BIOS and Linux driver both get the order right.

I investigated Promise's Linux driver (v1.01.0.23), and found
that it explicitly changes the mapping from logical port number
to ATA engine MMIO address on the SATAII TX4 cards. It does this
on all SATAII TX4 cards, without inspecting revision etc. The
SATAII TX2plus cards continue to use the same mapping that was
used for the first-generation chips.

This patch updates sata_promise to use the new port number to
ATA engine mapping on SATAII TX4 cards, which fixes the drive
enumeration order problem on those cards. Tested on several
1st and 2nd generation TX2plus and TX4 chips.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09 20:15:46 -04:00
Mikael Pettersson
8ffcfd9d0d sata_promise: fix another error decode regression
The sata_promise error decode update changed pdc_host_intr()
to return and not complete the qc after detecting an error.
Unfortunately not completing the qc:s causes them to always
time out on error, which is wrong and has nasty side-effects.

This patch updates pdc_error_intr() to call ata_port_abort(),
similar to ahci and sata_sil24. Doing this is important as it
makes EH see the original error and not a bogus timeout.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09 20:15:46 -04:00
Tejun Heo
eca25dca17 libata: convert drivers with combined SATA/PATA ports to new init model
Convert sata_via and sata_promise to new init model.  Both controllers
can have combined configuration (SATA + PATA) and used twisted
initialization method (modifying port in ->port_start) to overcome
probe_ent limitations.

This patch converts both drivers to new init model in which such
configuration is natively supported.

* promise: Combined pata port now uses separate port_info entry right
  after the sata counterpart entry.

* promise: Controller configuration is discerned using ap->flags.
  This simplifies init path and makes it look more like other LLDs.

* via: Both SATA and PATA ports in vt6421 are represented in their
  own port_info structure.

Tested on PDC20375 (SATA150 TX2plus) [105a:3375] and PDC40775 (SATA
300 TX2plus) [105a:3d73].  Couldn't test via cuz my c3 won't boot the
current kernel.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:03 -04:00
Tejun Heo
a51d644af6 libata: improve AC_ERR_DEV handling for ->post_internal_cmd
->post_internal_cmd is simplified EH for internal commands.  Its
primary mission is to stop the controller such that no rogue memory
access or other activities occur after the internal command is
released.  It may provide error diagnostics by setting qc->err_mask
but this hasn't been a requirement.

To ignore SETXFER failure for CFA devices, libata needs to know
whether a command was failed by the device or for any other reason.
ie. internal command needs to get AC_ERR_DEV right.

This patch makes the following changes to AC_ERR_DEV handling and
->post_internal_cmd semantics to accomodate this need and simplify
callback implementation.

1. As long as the correct bits in the result TF registers are set,
   there is no need to set AC_ERR_DEV explicitly.  libata EH core
   takes care of that for both normal and internal commands.

2. The only requirement for ->post_internal_cmd() is to put the
   controller into quiescent state.  It needs not to set any err_mask.

3. ata_exec_internal_sg() performs minimal error analysis such that
   AC_ERR_DEV is automatically set as long as result_tf is filled
   correctly.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:02 -04:00
Mikael Pettersson
ce2d3abc29 sata_promise: fix error decode regression
Promise ATA ports should always be reset by pdc_reset_port()
when errors are detected, but the recent error reason decoding
update to sata_promise replaced that reset with a freeze.

This patch changes the error detection to do a reset again.
This makes the error decoding update safer, as it now only
adds error decoding without changing any other behaviour.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:01 -04:00
Mikael Pettersson
176efb0544 sata_promise: decode and report error reasons
This patch adds much needed error reason decoding and
reporting to sata_promise. It's simplistic but should
log all relevant error info the controller provides.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:15:59 -04:00
Mikael Pettersson
724114a573 sata_promise: separate SATA and PATA ops
This patch changes sata_promise so that the PATA ports
on TX2plus chips are bound to the pdc_pata_ops structure.
This means that operations called from the SATA ops
structures don't need any SATA-vs-PATA tests any more.
Instead, operations that depend on a port being SATA or
PATA are separated into different procedures.

* pdc_cable_type() is split into a PATA version and a
  SATA version
* pdc_error_handler() is split into a PATA version and a
  SATA version, that both call a common version after
  setting up the `hardreset' function pointer
* pdc_old_check_atapi_dma() is now only used for SATAI
  ports, so is renamed to pdc_old_sata_check_atapi_dma()
  and simplified
* pdc_sata_scr_{read,write}() are now only used for SATA
  ports, so their is-not-SATA tests are removed
* pdc_port_start() is split into three procedures: a wrapper
  which performs the ->ops adjustment on TX2plus PATA ports,
  a procedure with the common code, and a procedure with
  the SATA-specific code (this bit might be cleaned up by
  Tejun's new init model)

Tested on 20619, 20575, and 20775 chips.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:15:59 -04:00
Mikael Pettersson
799331fda0 sata_promise: add missing cable_detect hooks
The recent change which moved cable detection from
pdc_pre_reset() to the new ->cable_detect hook only
added the hook for SATAII chips, leaving SATAI chips
and the 20619 without the hook. Fixed by this patch.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:15:59 -04:00
Alan Cox
e2a9752a21 sata_promise: Switch to cable method, clean up some bits as a result
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:15:57 -04:00
Jeff Garzik
cb48cab7f3 [libata] bump versions
Bump versions based on changes submitted during 2.6.21 merge window.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-26 06:04:24 -05:00
Mikael Pettersson
098cdff3d4 sata_promise: simplify port setup
Each place in pdc_ata_init_one() that initialises a SATA
port first calls pdc_ata_setup_port(), and then manually
assigns the port's ->scr_addr. Simplify the code by extending
pdc_ata_setup_port() to also handle scr_addr initialisation;
for PATA ports we pass NULL as scr_addr.

The initialisation of the PATA-only 20619 redundantly set
up scr_addr for the ports. Remove this.

Tested on 20619, 20575, and 20775 chips.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-25 15:41:40 -05:00
Mikael Pettersson
540477b4d9 sata_promise: fix 20619 new EH merge error
When I merged my 20619 new EH conversion with #libata-upstream
I had to manually resolve a conflict, and inadvertently lost
pdc_pata_ops' ->post_internal_cmd binding. Corrected by this patch.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-25 15:41:40 -05:00