Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/gadget/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/gadget.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.
Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.
Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.
Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.
Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.
This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use of_clk_get_parent_count() instead of open coding.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The required clocks needs to be enabled before the first register
access. After commit fe8abf332b ("usb: dwc3: support clocks and resets
for DWC3 core"), this happens when the dwc3_core_is_valid function is
called, but the mentioned commit adds that call in the wrong place,
before the clocks are enabled. So, move that call after the
clk_bulk_enable() to ensure the clocks are enabled and the reset
deasserted.
I detected this while, as experiment, I tried to move the clocks and resets
from the glue layer to the DWC3 core on a Samsung Chromebook Plus.
That was not detected before because, in most cases, the glue layer
initializes SoC-specific things and then populates the child "snps,dwc3"
with those clocks already enabled.
Fixes: b873e2d0ea ("usb: dwc3: Do core validation early on probe")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_qcom_clk_init() is called with of_count_phandle_with_args() as an
argument. If of_count_phandle_with_args() returns an error, the number
of clocks will be a negative value and will lead to undefined behaviour.
Ensure we check for an error before attempting to blindly use the value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When booting with Device Tree, the current default boot configuration
table option, the request to boot via 'host mode' comes from the
'dr_mode' property. A property of the same name can be used inside
ACPI tables too. However it is missing from the SDM845's ACPI tables
so we have to supply this information using Platform Device Properties
instead.
This does not change the behaviour of any currently supported devices.
The property is only set on ACPI enabled platforms, thus for H/W
booting DT, unless a 'dr_mode' property is present, the default is
still OTG (On-The-Go) as per [0]. Any new ACPI devices added will
also be able to over-ride this implementation by providing a 'dr_mode'
property in their ACPI tables. In cases where 'dr_mode' is omitted
from the tables AND 'host mode' should not be the default (very
unlikely), then we will have to add some way of choosing between them
at run time - most likely by ACPI HID.
[0] Documentation/devicetree/bindings/usb/generic.txt
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In Linux, the DWC3 core exists as its own independent platform device.
Thus when describing relationships in Device Tree, the current default
boot configuration table option, the DWC3 core often resides as a child
of the platform specific node. Both of which are given their own
address space descriptions and the drivers can be mostly agnostic to
each other.
However, other Operating Systems have taken a more monolithic approach,
which is evident in the configuration ACPI tables for the Qualcomm
Snapdragon SDM850, where all DWC3 (core and platform) components are
described under a single IO memory region.
To ensure successful booting using the supplied ACPI tables, we need to
devise a way to chop up the address regions provided and subsequently
register the DWC3 core with the resultant information, which is
precisely what this patch aims to achieve.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support for the OTG ID change interrupt to switch between Host
and Device mode.
Tested on the Hardkernel Odroid-N2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
The macro name DWC3_DCTL_LPM_ERRATA is uninformative and does not do
masking. Remove DWC3_DCTL_LPM_ERRATA_MASK and rename
DWC3_DCTL_LPM_ERRATA to DWC3_DCTL_NYET_THRES with proper masking.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The max possible value for DCTL.LPM_NYET_THRES is 15 and not 255. Change
the default value to 15.
Cc: stable@vger.kernel.org
Fixes: 80caf7d21a ("usb: dwc3: add lpm erratum support")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 is missing the printing of control request GET_STATUS(device)
tracepoint. This patch prints that.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The setting of the dr_mode may need to check the controller's revision.
The revision is set in the dwc3_core_is_valid(), which comes after
dr_mode setting. Let's move it closer to the start of the dwc3_probe()
function and before calling dwc3_get_dr_mode().
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All DWC3 controllers are LPM capable. Report that in the
usb_gadget.lpm_capable for the gadget driver to properly output the
bcdUSB value in the descriptor.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_gadget_suspend() is called under dwc->lock spinlock. In such context
calling synchronize_irq() is not allowed. Move the problematic call out
of the protected block to fix the following kernel BUG during system
suspend:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:112
in_atomic(): 1, irqs_disabled(): 128, pid: 1601, name: rtcwake
6 locks held by rtcwake/1601:
#0: f70ac2a2 (sb_writers#7){.+.+}, at: vfs_write+0x130/0x16c
#1: b5fe1270 (&of->mutex){+.+.}, at: kernfs_fop_write+0xc0/0x1e4
#2: 7e597705 (kn->count#60){.+.+}, at: kernfs_fop_write+0xc8/0x1e4
#3: 8b3527d0 (system_transition_mutex){+.+.}, at: pm_suspend+0xc4/0xc04
#4: fc7f1c42 (&dev->mutex){....}, at: __device_suspend+0xd8/0x74c
#5: 4b36507e (&(&dwc->lock)->rlock){....}, at: dwc3_gadget_suspend+0x24/0x3c
irq event stamp: 11252
hardirqs last enabled at (11251): [<c09c54a4>] _raw_spin_unlock_irqrestore+0x6c/0x74
hardirqs last disabled at (11252): [<c09c4d44>] _raw_spin_lock_irqsave+0x1c/0x5c
softirqs last enabled at (9744): [<c0102564>] __do_softirq+0x3a4/0x66c
softirqs last disabled at (9737): [<c0128528>] irq_exit+0x140/0x168
Preemption disabled at:
[<00000000>] (null)
CPU: 7 PID: 1601 Comm: rtcwake Not tainted
5.0.0-rc3-next-20190122-00039-ga3f4ee4f8a52 #5252
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c01110f0>] (unwind_backtrace) from [<c010d120>] (show_stack+0x10/0x14)
[<c010d120>] (show_stack) from [<c09a4d04>] (dump_stack+0x90/0xc8)
[<c09a4d04>] (dump_stack) from [<c014c700>] (___might_sleep+0x22c/0x2c8)
[<c014c700>] (___might_sleep) from [<c0189d68>] (synchronize_irq+0x28/0x84)
[<c0189d68>] (synchronize_irq) from [<c05cbbf8>] (dwc3_gadget_suspend+0x34/0x3c)
[<c05cbbf8>] (dwc3_gadget_suspend) from [<c05bd020>] (dwc3_suspend_common+0x154/0x410)
[<c05bd020>] (dwc3_suspend_common) from [<c05bd34c>] (dwc3_suspend+0x14/0x2c)
[<c05bd34c>] (dwc3_suspend) from [<c051c730>] (platform_pm_suspend+0x2c/0x54)
[<c051c730>] (platform_pm_suspend) from [<c05285d4>] (dpm_run_callback+0xa4/0x3dc)
[<c05285d4>] (dpm_run_callback) from [<c0528a40>] (__device_suspend+0x134/0x74c)
[<c0528a40>] (__device_suspend) from [<c052c508>] (dpm_suspend+0x174/0x588)
[<c052c508>] (dpm_suspend) from [<c0182134>] (suspend_devices_and_enter+0xc0/0xe74)
[<c0182134>] (suspend_devices_and_enter) from [<c0183658>] (pm_suspend+0x770/0xc04)
[<c0183658>] (pm_suspend) from [<c0180ddc>] (state_store+0x6c/0xcc)
[<c0180ddc>] (state_store) from [<c09a9a70>] (kobj_attr_store+0x14/0x20)
[<c09a9a70>] (kobj_attr_store) from [<c02d6800>] (sysfs_kf_write+0x4c/0x50)
[<c02d6800>] (sysfs_kf_write) from [<c02d594c>] (kernfs_fop_write+0xfc/0x1e4)
[<c02d594c>] (kernfs_fop_write) from [<c02593d8>] (__vfs_write+0x2c/0x160)
[<c02593d8>] (__vfs_write) from [<c0259694>] (vfs_write+0xa4/0x16c)
[<c0259694>] (vfs_write) from [<c0259870>] (ksys_write+0x40/0x8c)
[<c0259870>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed55ffa8 to 0xed55fff0)
...
Fixes: 01c10880d2 ("usb: dwc3: gadget: synchronize_irq dwc irq in suspend")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we read an array of integers from device properties,
the temporary buffer is allocated.
However, in case of dwc3_set_incr_burst_type() it's not freed.
Free allocated buffer immediately after use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that the bulk API has a "get all of the clocks" helper to match
what this code wants, there's little reason not to switch over.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This drivers supports the on-probe setup of the OTG mode, and manually
via a debugfs interface. The IRQ mode change detect is yet to be added
in a future patchset, mainly due to lack of hardware to validate on.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Keep EXTCON support optional, as some platforms do not need it.
Do the same for USB_DWC3_OMAP while we're at it.
Fixes: 3def4031b3 ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This contains a fix for the usage of shared resets that previously
generated a WARN on boot. In addition, there's a fix for CPU cache
maintenance of GEM buffers allocated using get_pages().
-----BEGIN PGP SIGNATURE-----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=nA5m
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.2-rc1
This contains a fix for the usage of shared resets that previously
generated a WARN on boot. In addition, there's a fix for CPU cache
maintenance of GEM buffers allocated using get_pages().
(airlied: contains a merge from a shared tegra tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190418151447.9430-1-thierry.reding@gmail.com
In order to be able to request an array of reset controls in acquired or
released mode, add the acquired flag to of_reset_control_array_get() and
pass the flag to subsequent calls of __of_reset_control_get().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In case the "linux,extcon-name" property is defined but device itself
is not ready, defer the probe.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
-----BEGIN PGP SIGNATURE-----
iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlxlU88dHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQYCTA/9EOtd5A2UkUkYIwh0
uV1NOTMIcTnQeNLxOe1c/3yNo4pxGeaKkVc4g/3pdh9dQ121DxUdKy3KAJkDsqDe
sbab7Ww2DZds17NqQfMloq3UyLjG2nCOJRl6UjoMCMcd4nVwi9by15W+NjBQSThw
3qvv9qVHiP9O7rKyUOMH/aPqHno1cEb8YJoFDdQuYL3Gv6kbbhfjynBhIzO5W+Zq
Za1aIayUEcbnk7OXLj2jUaaQS9TKb8zdhSXb8UGIuQkHQ/GbZF/Me/RbJif+KY7L
P+A8PUrk08B/QKm5PdmPjl5MjjoXa8/sEVzOMqEG4vtT8loQ6WCm9k1NNvzHXPa3
aRD316Yvp5EAPUBv3B8IrYUnLRH/xdG1YzEnDHrtsSwVN50qUXXUnvX2TkBic7M/
kEmcB2TS1Pqlto0DUwuSlNUQ6KHDRIxoZ66jdxPfORMzEBWVtoIRLhLSG/oMXYFC
SvwKKv2UY0Z/55sUEDuAR8VO3a/KI4FefcmeKsem5I4FfRdQ0SumNYmolpY7Kpqo
BL3P+4LQ4CiNBNoBEfifKRUy/jEfU7fTDedgrua8zMH/c7zFXGL+SGNkIixRESO1
B4Cl5/INP4slwtegvSsp3A/4hakPGyBhebCLKVZ/M71BeG0+1TPlAZruPO8SIiqc
7FSxVk2X9Ic0mkXmSqnT7ItuLUU=
=4fTL
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
Currently req->num_trbs is not reset after the TRBs are skipped and
processed from the cancelled list. The gadget driver may reuse the
request with an invalid req->num_trbs, and DWC3 will incorrectly skip
trbs. To fix this, simply reset req->num_trbs to 0 after skipping
through all of them.
Fixes: c3acd59014 ("usb: dwc3: gadget: use num_trbs when skipping TRBs on ->dequeue()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we're disabling the endpoint anyway, we don't worry about
getting endpoint command completion interrupt.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
i.MX6QP and i.MX7D platform use a PCIe controller with the same VID and
PID as this USB controller. The system may incorrectly match this driver
to that PCIe controller. To workaround this, specifically use class type
USB with PCI device ID to prevent incorrect driver matching.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of assuming that our buffer is big enough, let's pass the
buffer size around so printing functions can make sure they won't
overflow the buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we modified the code to fix a race condition, it's clear that
DWC3_EP_END_TRANSFER_PENDING is unnecessary, considering that
DWC3_EP_TRANSFER_STARTED will remain set until End Transfer completes.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a rare race condition that may happen during a Disconnect
Interrupt if we have a started request that happens to be
dequeued *after* completion of End Transfer command. If that happens,
that request will be left waiting for completion of an End Transfer
command that will never happen.
If End Transfer command has already completed before, we are safe to
giveback the request straight away.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have a proper flag for testing that we have a valid transfer in
flight, let's use that instead.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We must wait until End Transfer completes in order to clear
DWC3_EP_TRANSFER_STARTED, otherwise we may confuse the driver.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If clk_prepare_enable() fails in dwc3_exynos_probe() or in
dwc3_exynos_resume(), exynos->clks[0] is left undisabled
because of usage preincrement in while condition.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 9f2168367a ("usb: dwc3: exynos: Rework clock handling and prepare for new variants")
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For OUT endpoints, zero-length transfers require MaxPacketSize buffer as
per the DWC_usb3 programming guide 3.30a section 4.2.3.3.
This patch fixes this by explicitly checking zero length
transfer to correctly pad up to MaxPacketSize.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have req->status, we don't need this extra flag
anymore. It's safe to remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Queueing the same request twice can introduce hard-to-debug
problems. At least one function driver - Android's f_mtp.c - is known
to cause this problem.
While that function is out-of-tree, this is a problem that's easy
enough to avoid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch starts tracking dwc3_request status. A following patch will
build on top of this to prevent a request from being queued twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The AM654 SoC contains a DWC3 controller with TI specific
wrapper. Add support for that.
Unlike the Keystone 2 case, for AM654 We don't need to
process any IRQs for basic USB operation.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On v3.10a in dual-role mode, if port is in device mode
and gadget driver isn't loaded, the OTG event interrupts don't
come through.
It seems that if the core is configured to be OTG2.0 only,
then we can't leave the DCFG.DEVSPD at Super-speed (default)
if we expect OTG to work properly. It must be set to High-speed.
Fix this issue by configuring DCFG.DEVSPD to the supported
maximum speed at gadget init. Device tree still needs to provide
correct supported maximum speed for this to work.
This issue wasn't present on v2.40a but is seen on v3.10a.
It doesn't cause any side effects on v2.40a.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a MSM8998 specific DT compatible so that we can properly bind to the
device and enable the USB controller.
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the link_state is uninitialized and the default value is 0(U0)
before the first time we start the udc, and after we start the udc then
stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with
an undefined link_state:
WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
OUT endpoint requests may somtimes have this flag set when
preparing to be submitted to HW indicating that there is an
additional TRB chained to the request for alignment purposes.
If that request is removed before the controller can execute the
transfer (e.g. ep_dequeue/ep_disable), the request will not go
through the dwc3_gadget_ep_cleanup_completed_request() handler
and will not have its needs_extra_trb flag cleared when
dwc3_gadget_giveback() is called. This same request could be
later requeued for a new transfer that does not require an
extra TRB and if it is successfully completed, the cleanup
and TRB reclamation will incorrectly process the additional TRB
which belongs to the next request, and incorrectly advances the
TRB dequeue pointer, thereby messing up calculation of the next
requeust's actual/remaining count when it completes.
The right thing to do here is to ensure that the flag is cleared
before it is given back to the function driver. A good place
to do that is in dwc3_gadget_del_and_unmap_request().
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
