The SPI host controller is the same as used in Baytrail, only the ACPI ID
is different so add this new ID to the list.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
It was observed that after module removal followed by insertion,
the SW mode chipselect is not properly set. Thus causing transfer
failure due to incorrect CS toggling.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit 7dd6278733 (spi/pxa2xx: Convert
to core runtime PM) master->auto_runtime_pm was set to true.
In this case pm_runtime_enable() must be called *before*
spi_register_master(), otherwise the kernel hangs with this error
message:
spi_master spi0: Failed to power device: -13
A similar fix, but for spi/hspi, was applied in
268d76430d.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warning:
drivers/spi/spi-pxa2xx.c:1270:12: warning: ‘pxa2xx_spi_suspend’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
converted the driver to use ACPI provided DMA helpers but it forgot to
initialize the platform data for the channels to -1. Failing to do so will
result inadvertent match in the filter function because 0 is a valid
channel number.
Prevent this from happening by initializing both platform data channels
correctly to -1.
Fixes: cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The Intel LPSS SPI private register bits have to be restored
when system resume from S3 suspend.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Newer Intel PCHs with LPSS have the same SPI controllers than Haswell but
ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
User-visible strings are more difficult to grep from sources if they are
separated to multiple source lines. This is worse than over 80 columns long
line code style violation.
Fix this by making those to single-line strings or by breaking them between
variables.
While at there, convert if (printk_ratelimit()) dev_warn() to use
dev_warn_ratelimited in spi-pxa2xx.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current interrupt handler calls pm_runtime_suspended() to check if the
device is suspended or not. However, runtime PM status of the device is
only set to suspended once all PM runtime suspend hooks have executed.
In case of Intel Lynxpoint we have the device bound to the ACPI power
domain and its runtime suspend hook will put the device to D3hot (or D3cold
if possible). This means that the device is powered off before its state is
set to runtime suspended. While in this state the device might get an
interrupt that is meant for another device (as the interrupt line is
shared), and because the device is powered off accessing its registers will
return 0xffffffff that the driver misinterprets as an invalid state.
When this happens user will see messages like below on the console:
pxa2xx-spi INT33C0:00: bad message state in interrupt handler
Fix this by checking the status register for ~0 and returning IRQ_NONE in
that case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is an additional bit in the Intel LPSS SPI private registers that
needs to be set in order to be able to use DMA with the SPI controller.
Enable this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Intel BayTrail has one general purpose SPI controller that is compatible
with Intel Low Power Subsystem SPI. The controller is enumerated from ACPI
namespace with ACPI ID 80860F0E.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we have these nice DMA API helper functions we can take advantage
of those instead of open-coding the channel/request line extraction from
ACPI. Use the _compat version which still allows passing the
channel/request line from platform data.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit cbfd6a21b6 (spi/pxa2xx: Convert to devm_ioremap_resource())
converted the driver to use devm_ioremap_resource(). However it causes
following warning to be emitted:
drivers/spi/spi-pxa2xx.c: In function ‘pxa2xx_spi_acpi_get_pdata’:
drivers/spi/spi-pxa2xx.c:1094:3: warning: return makes pointer from integer without a cast [enabled by default]
Fix this by returning NULL as it was done previously (error printing is
already done by devm_ioremap_resource()).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A fairly quiet release for SPI, mainly driver work. A few highlights:
- Supports bits per word compatibility checking in the core.
- Allow use of the IP used in Freescale SPI controllers outside
Freescale SoCs.
- DMA support for the Atmel SPI driver.
- New drivers for the BCM2835 and Tegra114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+Omc
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, mainly driver work. A few highlights:
- Supports bits per word compatibility checking in the core.
- Allow use of the IP used in Freescale SPI controllers outside
Freescale SoCs.
- DMA support for the Atmel SPI driver.
- New drivers for the BCM2835 and Tegra114"
* tag 'spi-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (68 commits)
spi-topcliff-pch: fix to use list_for_each_entry_safe() when delete list items
spi-topcliff-pch: missing platform_driver_unregister() on error in pch_spi_init()
ARM: dts: add pinctrl property for spi node for atmel SoC
ARM: dts: add spi nodes for the atmel boards
ARM: dts: add spi nodes for atmel SoC
ARM: at91: add clocks for spi dt entries
spi/spi-atmel: add dmaengine support
spi/spi-atmel: add flag to controller data for lock operations
spi/spi-atmel: add physical base address
spi/sirf: fix MODULE_DEVICE_TABLE
MAINTAINERS: Add git repository and update my address
spi/s3c64xx: Check for errors in dmaengine prepare_transfer()
spi/s3c64xx: Fix non-dmaengine usage
spi: omap2-mcspi: fix error return code in omap2_mcspi_probe()
spi/s3c64xx: let device core setup the default pin configuration
MAINTAINERS: Update Grant's email address and maintainership
spi: omap2-mcspi: Fix transfers if DMADEVICES is not set
spi: s3c64xx: move to generic dmaengine API
spi-gpio: init CS before spi_bitbang_setup()
spi: spi-mpc512x-psc: let transmiter/receiver enabled when in xfer loop
...
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ACPI handle of struct spi_master's dev member should not be
set, because this causes that struct spi_master to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct spi_master). Consequently,
acpi_register_spi_devices() should use the ACPI handle of the
parent of the struct spi_master it is called for rather than that
struct spi_master's ACPI handle (which should be NULL).
Make that happen and modify the spi-pxa2xx driver, which currently is
the only driver for ACPI-enumerated SPI controller chips, not to set
the ACPI handle for the struct spi_master it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Intel LPSS SPI controllers need to have bit 0 (disable_ssp_dma_finish) set
in SSP_REG in order to properly perform DMA transfers spanning over
multiple blocks.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Intel Lynxpoint PCH Low Power Subsystem has two general purpose SPI
controllers that are LPSS_SSP compatible. These controllers are enumerated
from ACPI namespace with ACPI IDs INT33C0 and INT33C1.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Intel LPSS SPI is pretty much the same as the PXA27xx SPI except that it
has few additional features over the original:
o FIFO depth is 256 entries
o RX FIFO has one watermark
o TX FIFO has two watermarks, low and high
o chip select can be controlled by writing to a register
The new FIFO registers follow immediately the PXA27xx registers but then there
are some additional LPSS private registers at offset 1k or 2k from the base
address. For these private registers we add new accessors that take advantage
of drv_data->lpss_base once it is resolved.
We add a new type LPSS_SSP that can be used to distinguish the LPSS devices
from others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is useful when testing the functionality of the controller from userspace
and there aren't any real SPI slave devices connected to the bus.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of SPI traffic within short period of time.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to use DMA with this driver on non-PXA platforms we implement
support for the generic DMA engine API. This lets user to use different DMA
engines with little or no modification to the driver.
Request lines and channel numbers can be passed to the driver from the
platform specific data.
The DMA engine implementation will be selected by default even on PXA
platform. User can select the legacy DMA API by enabling Kconfig option
CONFIG_SPI_PXA2XX_PXADMA.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).
While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.
Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare() respectively in order to support the common clk
framework. Otherwise we get warnings on the console as the clock is not
prepared before it is enabled.
In addition we must cache the maximum clock rate to drv_data->max_clk_rate
at probe time because clk_get_rate() cannot be called in tasklet context.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SPI core provides infrastructure for standard message queueing so use
that instead of handling everything in the driver. This simplifies the
driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix following warnings seen when compiling 64-bit:
drivers/spi/spi-pxa2xx.c: In function ‘map_dma_buffers’: drivers/spi/spi-pxa2xx.c:384:7: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:384:40: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c: In function ‘pxa2xx_spi_probe’:
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:27: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spi-pxa2xx-pci glue driver had to implement pxa_ssp_request()/free() in
order to support the spi-pxa2xx platform driver. Since the ACPI enabled
platforms can use the same platform driver we would need to implement
pxa_ssp_request()/free() in some central place that can be shared by the
ACPI and PCI glue code.
Instead of doing that we can make pxa_ssp_request()/free() to be available
only when CONFIG_ARCH_PXA is set. On other arches these are being stubbed
out in preference to passing the ssp_device from the platform data
directly.
We also change the SPI bus number to be taken from ssp->port_id instead of
platform device id. This way the supporting code that passes the ssp can
decide the number (or it can set it to the same as pdev->id).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Alan Cox