The IBS timers are not stopped properly once BT OFF is triggered.
we could see IBS commands being sent along with version command,
so stopped IBS timers while Bluetooth is off.
Fixes: 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Signed-off-by: Panicker Harish <quic_pharish@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch add missing HCI quirks and MSFT extension for legacy
bootloader when it is running in the operational firmware.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If there are failure cases in getting patch status, it should return the
error code (-EIO).
Fixes: fc342c4dc4 ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For Mediatek chipset, it can not enabled if there are something wrong
in btmtk_setup_firmware_79xx(). Thus, the process must be terminated
and returned error code.
Fixes: fc342c4dc4 ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes btusb to queue ACL and events during a polling interval
by using of a delayed work, with the interval working as a time window
where frames received from different endpoints are considered to be
arrived at same time and then attempt to resolve potential conflics by
processing the events ahead of ACL packets.
It worth noting though that priorizing events over ACL data may result
in inverting the order compared to how they appeared over the air, for
instance there may be packets received before a disconnect event that
will be discarded and unencrypted packets received before encryption
change which would considered encrypted, because of these potential
changes on the order the support for queuing during the polling
interval is not enabled by default so it requires setting
force_poll_sync debugfs while the adapter is down.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some Macs with the T2 security chip had Bluetooth not working.
To fix it we add DMI based quirks to disable querying of LE Tx power.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Tested-by: Orlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea521 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to MT7921 btusb, we enable AOSP extension for MT7921 btmtksdio
as well.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmtksdio have to rely on MMC_PM_KEEP_POWER in pm_flags to avoid that
SDIO power is being shut off during the device is in suspend. That fixes
the SDIO command fails to access the bus after the device is resumed.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Runtime pm ops is not aware the sdio_func status that is probably
being disabled by btmtksdio_close. Thus, we are only able to access the
sdio_func for the runtime pm operations only when the sdio_func is
available.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cancel sync commands when transmission of URBs fail. This is done for
both failures to send a command URB and also when the interrupt URB used
to retrieve a response fails.
This approach is sufficient to quickly deal with certain errors such as
a device being disconnected while synchronous commands are done during
initialization.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
After the previous patches, noone needs 'file' parameter in neither
ioctl hook from tty_ldisc_ops. So remove 'file' from both of them.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> [NFC]
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122094529.24171-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The board ID should be split into two bytes.
The 1st byte is chip ID, and the 2nd byte is platform ID.
For example, board ID 0x010A, 0x01 is platform ID. 0x0A is chip ID.
we have several platforms, and platform IDs are continuously added.
We would not distinguish different chips if we get these mixed up.
Platform ID:
0x00 is for Mobile
0x01 is for X86
0x02 is for Automotive
0x03 is for Consumer electronic
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the existent variable to drop the unnecessary variable created.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support of processing the firmware coredump and log for the diagnostic
purpose.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Do not use "/**" to begin a non-kernel-doc comment.
Fixes this build warning:
drivers/bluetooth/btmrvl_main.c:2: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
it is erroneous to calculate padding by subtracting length of type
indication from skb->len, it will cause data analysis error for
alignment which is greater than 1, so fixed by adding length of type
indication with skb->len.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPczQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykWbwCfaIScbUoCUx+h/uP93nKKD8B3KgYAoMvFuhhD
D/fTLggs12x5NsvLBgtZ
=rq0R
-----END PGP SIGNATURE-----
Merge tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits)
tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description
serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
tty: rpmsg: Define tty name via constant string literal
tty: rpmsg: Add pr_fmt() to prefix messages
tty: rpmsg: Use dev_err_probe() in ->probe()
tty: rpmsg: Unify variable used to keep an error code
tty: rpmsg: Assign returned id to a local variable
serial: stm32: push DMA RX data before suspending
serial: stm32: terminate / restart DMA transfer at suspend / resume
serial: stm32: rework RX dma initialization and release
serial: 8250_pci: Remove empty stub pci_quatech_exit()
serial: 8250_pci: Replace custom pci_match_id() implementation
serial: xilinx_uartps: Fix race condition causing stuck TX
serial: sunzilog: Mark sunzilog_putchar() __maybe_unused
Revert "tty: hvc: pass DMA capable memory to put_chars()"
Revert "virtio-console: remove unnecessary kmemdup()"
serial: 8250_pci: Replace dev_*() by pci_*() macros
serial: 8250_pci: Get rid of redundant 'else' keyword
serial: 8250_pci: Refactor the loop in pci_ite887x_init()
tty: add rpmsg driver
...
the RF performance of wcn6855 soc chip from different foundries will be
difference, so we should use different nvm to configure them.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
add MT7921s Bluetooth support
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Each packet should be sent out until the device emits the TX_EMPTY signal
to the host, that is firmware people suggested to add to meet the actual
firmware behavior and that is compatible among all the devices.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
That is a preliminary patch to introduce mt7921s support.
Use the register CRPLR to read packet length to make all the devices
share the common logic.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
That is a preliminary patch to introduce mt7921s support.
Update register CSDIOCSR operation that is suggested from the vendor
driver and is compatible to the all devices.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmtksdio belongs to WIFI/BT combo chip that would serve two radios in one
sdio_irq so that we have to move interrupt service to worker to ensure ISR
as short as possible.
The worker would serve the both Tx and Rx in a batch to effectively reduce
many interrupts to the host and to avoid excessive sdio lock contention
between various context (even from WiFi driver) and help to be more
efficient to complete command/event transation.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
That is a preliminary patch to introduce mt7921s support.
Explicitly set WHISR as write-1-clear method to all devices that is
the expected behavior the driver rely on.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add BT_MTK module that is a preliminary patch to introduce mt7921s support
to share the logic betweem btusb and btmtksdio.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The entry "brcm,bcm4330-bt" was listed twice in the table.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the missing bulk-out endpoint sanity check to probe() to avoid
division by zero in bfusb_send_frame() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
msft_opcode shall be use a vendor ogf (0x3f) but the check was
swifting the bits in the wrong order due to a missing parantesis
over val & 0xffff, but since the code already checks for values over
0xffff it shall not be necessary to perform that operation it now just
removes which makes it work properly when setting opcodes like 0xfce1.
Fixes: b8f5482c96 ("Bluetooth: vhci: Add support for setting msft_opcode and aosp_capable")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BCM4345 and BCM43455 devices soldered onto the PCB (non-removable),
use an UART connection for Bluetooth, such as in the Pinebook Pro,
and the advertised btsdio support as an SDIO function is ignored.
Reviewed-by: Dragan Simic <dragan.simic@gmail.com>
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On the reception of packets with an invalid packet type, the memory of
the allocated socket buffers is never freed. Add a default case that frees
these to avoid a memory leak.
Fixes: afd2daa26c ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a debugfs entries to set msft_opcode and aosp_capable enabling
vhci to emulate controllers with MSFT/AOSP extension support.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Intel Read Verision(TLV) data is parsed into a local structure variable
and it contains a field for bd address. Bd address is returned only in
bootloader mode and hence bd address in TLV structure needs to be validated
only if controller is present in boot loader mode.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The coccinelle check report:
"./drivers/bluetooth/btusb.c:2239:36-42:
ERROR: application of sizeof to pointer".
Using the real size to fix it.
Fixes: 5a87679ffd ("Bluetooth: btusb: Support public address configuration for MediaTek Chip.")
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: David Yang <davidcomponentone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the wakeup state of the vhci driver when the
force_wakeup is updated.
Fixes: 60edfad4fd ("Bluetooth: hci_vhci: Add force_prevent_wake entry")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Defer calls to hci_{suspend,resume}_dev to work so it doesn't block the
processing of the events.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
prevent_wake logic is backward since what it is really checking is
if the device may wakeup the system or not, not that it will prevent
the to be awaken.
Also looking on how other subsystems have the entry as power/wakeup
this also renames the force_prevent_wake to force_wakeup in vhci driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some un-support wakeup platforms keep USB power and suspend signal
is coming late, this makes Realtek some chip keep its firmware,
and make it never load new firmware.
So use vendor specific HCI command to ask them drop its firmware after
system shutdown or resume.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The rtl8821c class of Realtek devices does support the Microsoft
extensions and thus enable them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds force_prevent_wake which can be used to force a certain state
while interacting with force_suspend.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds force_suspend which can be used to force the controller into
suspend/resume state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btrsi.c hasn't use any macro or function declared in net/genetlink.h.
Thus, these files can be removed from btrsi.c safely without
affecting the compilation of the ./drivers/bluetooth module
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device table already has the option to hold device specific details
and thus include the support for Microsoft extensions there as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch enables Realtek 8822C and 8852A to support the AOSP
extension.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables Qualcomm WCN399x to support the AOSP extension.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the hci_uart_register_device() call is the last thing we do in
h5_serdev_probe() we can simply directly return its return-value.
Cc: Archie Pusaka <apusaka@google.com>
Suggested-by: Archie Pusaka <apusaka@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The recently added H5_WAKEUP_DISABLE h5->flags flag gets checked in
h5_btrtl_open(), but it gets set in h5_serdev_probe() *after*
calling hci_uart_register_device() and thus after h5_btrtl_open()
is called, set this flag earlier.
Also on devices where suspend/resume involves fully re-probing the HCI,
runtime-pm suspend should not be used, make the runtime-pm setup
conditional on the H5_WAKEUP_DISABLE flag too.
This fixes the HCI being removed and then re-added every 10 seconds
because it was being reprobed as soon as it was runtime-suspended.
Fixes: 66f077dde7 ("Bluetooth: hci_h5: add WAKEUP_DISABLE flag")
Fixes: d9dd833cf6 ("Bluetooth: hci_h5: Add runtime suspend")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After the previous patch, there are no users of 'file' in
n_tty_ioctl_helper. So remove it also from there.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bdev->evt_skb will get freed in the normal path and one error path
of mtk_hci_wmt_sync, while the other error paths do not free it,
which may cause a memleak. This bug is suggested by a static analysis
tool, please advise.
Fixes: e0b67035a9 ("Bluetooth: mediatek: update the common setup between MT7622 and other devices")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Any unprivileged user can attach N_HCI ldisc and send packets coming from a
virtual controller by using PTYs.
Require initial namespace CAP_NET_ADMIN to do that.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
if platform provide gpio connect to BT_EN reset pin of qca btsoc chip,
we can do hardware reset instead of usb port reset.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot hit general protection fault in h5_recv(). The problem was in
missing NULL check.
hu->serdev can be NULL and we cannot blindly pass &serdev->dev
somewhere, since it can cause GPF.
Fixes: d9dd833cf6 ("Bluetooth: hci_h5: Add runtime suspend")
Reported-and-tested-by: syzbot+7d41312fe3f123a6f605@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently *ven_data is being assigned the return from a kmalloc call but
the out-of-memory check is checking ven_data and not *ven_data. Fix this
by adding the missing dereference * operator,
Addresses-Coverity: ("Dereference null return")
Fixes: 70dd978952 ("Bluetooth: btintel: Define a callback to fetch codec config data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Define the callbacks required to support offload codecs
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Define callback function to get codec config data. In HFP offload
usecase, controllers need to be set codec details before opening SCO.
This callback function is used to fetch vendor specific codec config
data.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For Intel controllers supporting HFP offload usecase,
define a callback function to fetch data_path_id
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Read offload use cases supported by controller.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The MediaTek chip support vendor specific HCI command(0xfc1a) to
change the public address. Add hdev->set_bdaddr handler for MediaTek
Chip. After doing a power cycle or MediaTek Bluetooth reset, BD_ADDR
will bring back the original one.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Boot address was not getting updated when controller is present
in boot mode which is required to move the controller from boot mode
to operation mode after firmware download. This patch reads boot address
even if controller is present in boot mode.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cache Boot address present in firmware file which
is later used in Intel_Soft_Reset command to bring
controller from boot mode to operational mode.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets up set_quality_report callback for Intel to
set and reset the debug features.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch supports the link statistics telemetry events for
intel controllers
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
To avoid the overhead on both the controller and the host, the
Intel link statistics telemetry events are disabled by default.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For the commit of 9e45524a01, wakeup is
always disabled for Realtek devices. However, there's the capability
for Realtek devices to apply USB wakeup.
In this commit, remove WAKEUP_DISABLE feature for Realtek devices.
If users would switch wakeup, they should access
"/sys/bus/usb/.../power/wakeup"
In this commit, it also adds the feature as WAKEUP_AUTOSUSPEND
for Realtek devices because it should set do_remote_wakeup on autosuspend.
Signed-off-by: Max Chou <max.chou@realtek.com>
Tested-by: Hilda Wu <hildawu@realtek.com>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth on the BCM43752 needs a patchram file to function correctly.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some USB BT adapters don't satisfy the MTU requirement mentioned in
commit e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
and have ALT 3 setting that produces no/garbled audio. Some adapters
with larger MTU were also reported to have problems with ALT 3.
Add a flag and check it and MTU before selecting ALT 3, falling back to
ALT 1. Enable the flag for Realtek, restoring the previous behavior for
non-Realtek devices.
Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1
works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3
works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling
ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad
audio) Intel 8087:0a2b.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Fixes: e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Jonathan Lampérth <jon@h4n.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch combines the setting up MSFT extension for the legacy and TLV
based bootloader into the common function based on hw_variant.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
From the ThP, it supports both legacy and TLV based HCI_Intel_Read_Version
command after downloading the operational firmware, and it causes the
driver to choose the wrong setup routines and missing firmware/ddc file.
So, as a workaround, this patch checks the fw variant from the TLV based
version, and if the device is legacy bootloader device, the legacy
HCI_Intel_Read_Version command is used to get the legacy version
information and run the legacy bootloader setup with it.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the exported functions to static if they are no
longer used by others.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the hci quirks for Intel devices into the setup
routines and cleaned up the driver flags.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch refactors the setup routines for legacy and TLV based
bootloader devices to the combined setup, and move the related functions
from btusb to btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a combined set_diag functions.
It also changes the btintel_set_diag_mfg() to static since it is no
longer used by others.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some platforms have an issue with BT LED when the interface is
down or BT radio is turned off, which takes 5 seconds to BT LED
goes off. This command turns off the BT LED immediately.
This patch sends the Intel vendor command to turn off the LED.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The some legacy ROM controllers have a bug with the first HCI command
sent to it returning number of completed commands as zero, which would
stall the command processing in the Bluetooth core.
As a workaround, send HCI Rest command first which will reset the
controller to fix the issue.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a data structure for btintel for btintel object, and the
definition of bootloder states. It also adds macros to set/test/clear
the flags.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch refactors the setup routines for legacy ROM product into
combined setup, and move the related functions from btusb to btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are multiple setup and shutdown functions for Intel device and the
setup function to be used is depends on the USB PID/VID, which makes
difficult to maintain the code and increases the code size.
This patch adds combined setup and shutdown functions to provide a
single entry point for all Intel devices and choose the setup functions
based on the information read with HCI_Intel_Read_Version command.
Starting from TyP device, the command and response parameters for
HCI_Intel_Read_Version command are changed even though OCF remains
same. However, the legacy devices still can handle the command without
error even if it has a extra parameter, so to simplify the flow,
the new command format is used to read the version information for
both legacy and new (tlv based) format.
Also, it also adds a routine to setup the hdev callbacks in btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the firmware hang or command no response, driver can reset the
bluetooth mcu via USB to recovery it. The reset steps as follows.
1. Cancel USB transfer requests before reset.
2. It use speicific USB HW Register to reset Bluetooth MCU, at the
same time, the USB Endpoint0 still keep alive.
3. Poll the USB HW register until reset is completed by Endpoint0.
4. To recovery unexpected USB state and behavior during resetting the
Bluetooth MCU, the driver need to reset the USB device for MT7921.
5. After the reset is completed, the Bluetooth MCU need to re-setup,
such as download patch, power-on sequence and etc.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Reviewed-by: Michael Sun <michaelfsun@google.com>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Kernel doc validator complains about few missed parameter descriptions.
Fill the gap by describing them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Mdiatek MT7921(7961) support MSFT HCI extensions, we are using
0xFD30 for VsMsftOpCode.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Turns out Hans de Goede completed the work I started last year trying to
improve Chinese-clone detection of CSR controller chips. Quirk after quirk
these Bluetooth dongles are more usable now.
Even after a few BlueZ regressions; these clones are so fickle that some
days they stop working altogether. Except on Windows, they work fine.
But this force-suspend initialization quirk seems to mostly do the trick,
after a lot of testing Bluetooth now seems to work *all* the time.
The only problem is that the solution ended up being masked under a very
stringent check; when there are probably hundreds of fake dongle
models out there that benefit from a good reset. Make it so.
Fixes: 81cac64ba2 ("Bluetooth: Deal with USB devices that are faking CSR vendor")
Fixes: cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")
Fixes: d74e0ae7e0 ("Bluetooth: btusb: Fix detection of some fake CSR controllers with a bcdDevice val of 0x0134")
Fixes: 0671c06623 ("Bluetooth: btusb: Add workaround for remote-wakeup issues with Barrot 8041a02 fake CSR controllers")
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel TyphoonPeak, GarfieldPeak Bluetooth controllers
support the Microsoft vendor extension and they are using
0xFC1E for VsMsftOpCode.
Verified on a GarfieldPeak device through bluetoothctl show
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Qualcomm WCN6855 Bluetooth controller supports the Microsoft vendor
extension, enable them by setting VsMsftOpCode to 0xFD70.
Verified on a WCN6855 device through bluetoothctl show
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy() but in
this case it is better to use the scnprintf to simplify the arithmetic.
This is a previous step in the path to remove the strcpy() function
entirely from the kernel.
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the valid le states quirk for WCN6855 and GarfieldPeak controller
so the 'central-peripheral' role is exposed in userspace.
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch allows the controller to suspend after a short period of
inactivity.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For chips that doesn't reset on suspend, we need to provide the correct
value of flow_control when it resumes. Therefore, store the flow
control value when reading from the config file to be reused upon
suspend.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some RTL chips resets the FW on suspend, so wakeup is disabled on
those chips. This patch introduces this WAKEUP_DISABLE flag so that
chips that doesn't reset FW on suspend can leave the flag unset and
is allowed to wake the host.
This patch also left RTL8822 WAKEUP_DISABLE flag unset, therefore
allowing it to wake the host, and preventing reprobing on resume.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
kernel-doc complains about a non-kernel-doc comment that uses "/**"
to begin the comment, so change it to just "/*".
drivers/bluetooth/btrsi.c:2: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Copyright (c) 2017 Redpine Signals Inc.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When reading the support debug features failed, there are not available
features init. Continue to set the debug features is illogical, we should
skip btintel_set_debug_features(), even if check it by "if (!features)".
Fixes: c453b10c2b ("Bluetooth: btusb: Configure Intel debug feature based on available support")
Signed-off-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_suspend_notifier which was introduced last year, is causing
problems for uart attached btrtl devices. These devices may loose their
firmware and their baudrate setting over a suspend/resume.
Since we don't even know the baudrate after a suspend/resume recovering
from this is tricky. The driver solves this by treating these devices
the same as USB BT HCIs which drop of the bus during suspend.
Specifically the driver:
1. Simply unconditionally turns the device fully off during
system-suspend to save maximum power.
2. Calls device_reprobe() from a workqueue to fully re-init the device
from scratch on system-resume (unregistering the old HCI and
registering a new HCI).
This means that these devices do not benefit from the suspend / resume
handling work done by the hci_suspend_notifier. At best this unnecessarily
adds some time to the suspend/resume time.
But in practice this is actually causing problems:
1. These btrtl devices seem to not like the HCI_OP_WRITE_SCAN_ENABLE(
SCAN_DISABLED) request being send to them when entering the
BT_SUSPEND_CONFIGURE_WAKE state. The same request send on
BT_SUSPEND_DISCONNECT works fine, but the second one send (unnecessarily?)
from the BT_SUSPEND_CONFIGURE_WAKE transition causes the device to hang:
[ 573.497754] PM: suspend entry (s2idle)
[ 573.554615] Filesystems sync: 0.056 seconds
[ 575.837753] Bluetooth: hci0: Timed out waiting for suspend events
[ 575.837801] Bluetooth: hci0: Suspend timeout bit: 4
[ 575.837925] Bluetooth: hci0: Suspend notifier action (3) failed: -110
2. The PM_POST_SUSPEND / BT_RUNNING transition races with the
driver-unbinding done by the device_reprobe() work.
If the hci_suspend_notifier wins the race it is talking to a dead
device leading to the following errors being logged:
[ 598.686060] Bluetooth: hci0: Timed out waiting for suspend events
[ 598.686124] Bluetooth: hci0: Suspend timeout bit: 5
[ 598.686237] Bluetooth: hci0: Suspend notifier action (4) failed: -110
In both cases things still work, but the suspend-notifier is causing
these ugly errors getting logged and ut increase both the suspend- and
the resume-time by 2 seconds.
This commit avoids these problems by disabling the hci_suspend_notifier.
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
The variable fw_ptr is assigned a value that is not read and the same value
is assigned in the patch goto. The assignment is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The continue statement in the for-loop has no effect,
remove it.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is btsoc timing issue, after host start to downloading bt firmware,
ep2 need time to switch from function acl to function dfu, so host add
20ms delay as workaround.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
if boardID is 0, will use the default nvm file without surfix.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According Realteks own BT drivers firmware RTL8761B is for UART
and RTL8761BU is for USB.
Change existing 8761B to UART and add an 8761BU entry for USB
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RTL8822 chipset supports WBS, and this information is conveyed in
btusb.c. However, the UART driver doesn't have this information just
yet.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Because mSBC frames do not need to be aligned to the SCO packet
boundary. Using USB ALT 3 let HCI payload >= 60 bytes, let mSBC
data satisfy 60 Bytes avoid payload unaligned situation and fixed
some headset no voise issue.
USB Alt 3 supported also need HFP support transparent MTU in 72 Bytes.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Moved extracting rom version info to common place as this code is
common in all if else ladder in qca_uart_setup.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1. Added support to download firmware image with mbn type for wcn6750
as it supports mbn type image.
2. If mbn type image is not present then check for tlv type image.
3. Added debug logs for mbn type image.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added regulators,GPIOs and changes required to power on/off wcn6750.
Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and
renamed it to qca_regulator_init().
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the device ID for the BCM43430B0 module, found e.g. in
certain revisions of AMPAK AP6212 chip. The required firmware file is
named 'BCM43430B0.hcd'.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In qca_power_shutdown() qcadev local variable is
initialized by hu->serdev.dev private data, but
hu->serdev can be NULL and there is a check for it.
Since, qcadev is not used before
if (!hu->serdev)
return;
we can move its initialization after this "if" to
prevent GPF.
Fixes: 5559904ccc ("Bluetooth: hci_qca: Add QCA Rome power off support to the qca_power_shutdown()")
Cc: stable@vger.kernel.org # v5.6+
Cc: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If btusb_mtk_submit_wmt_recv_urb returns error, wc should be freed and
then error should be returned to prevent memory leak.
Addresses-Coverity: ("Prevent memory leak")
Fixes: 4cbb375e997d ("Bluetooth: btusb: Fixed too many in-token issue for Mediatek Chip.")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The call to alloc_skb with the GFP_KERNEL flag can return a null sk_buff
pointer, so add a null check to avoid any null pointer deference issues.
Addresses-Coverity: ("Dereference null return value")
Fixes: afd2daa26c ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netfilter and wireguard trees.
The bpf vs lockdown+audit fix is the most notable.
Current release - regressions:
- virtio-net: fix page faults and crashes when XDP is enabled
- mlx5e: fix HW timestamping with CQE compression, and make sure they
are only allowed to coexist with capable devices
- stmmac:
- fix kernel panic due to NULL pointer dereference of mdio_bus_data
- fix double clk unprepare when no PHY device is connected
Current release - new code bugs:
- mt76: a few fixes for the recent MT7921 devices and runtime
power management
Previous releases - regressions:
- ice: - track AF_XDP ZC enabled queues in bitmap to fix copy mode Tx
- fix allowing VF to request more/less queues via virtchnl
- correct supported and advertised autoneg by using PHY capabilities
- allow all LLDP packets from PF to Tx
- kbuild: quote OBJCOPY var to avoid a pahole call break the build
Previous releases - always broken:
- bpf, lockdown, audit: fix buggy SELinux lockdown permission checks
- mt76: address the recent FragAttack vulnerabilities not covered
by generic fixes
- ipv6: fix KASAN: slab-out-of-bounds Read in fib6_nh_flush_exceptions
- Bluetooth:
- fix the erroneous flush_work() order, to avoid double free
- use correct lock to prevent UAF of hdev object
- nfc: fix NULL ptr dereference in llcp_sock_getname() after failed connect
- ieee802154: multiple fixes to error checking and return values
- igb: fix XDP with PTP enabled
- intel: add correct exception tracing for XDP
- tls: fix use-after-free when TLS offload device goes down and back up
- ipvs: ignore IP_VS_SVC_F_HASHED flag when adding service
- netfilter: nft_ct: skip expectations for confirmed conntrack
- mptcp: fix falling back to TCP in presence of out of order packets
early in connection lifetime
- wireguard: switch from O(n) to a O(1) algorithm for maintaining peers,
fixing stalls and a large memory leak in the process
Misc:
- devlink: correct VIRTUAL port to not have phys_port attributes
- Bluetooth: fix VIRTIO_ID_BT assigned number
- net: return the correct errno code ENOBUF -> ENOMEM
- wireguard:
- peer: allocate in kmem_cache saving 25% on peer memory
- do not use -O3
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=sNP5
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from bpf, wireless, netfilter and
wireguard trees.
The bpf vs lockdown+audit fix is the most notable.
Things haven't slowed down just yet, both in terms of regressions in
current release and largish fixes for older code, but we usually see a
slowdown only after -rc5.
Current release - regressions:
- virtio-net: fix page faults and crashes when XDP is enabled
- mlx5e: fix HW timestamping with CQE compression, and make sure they
are only allowed to coexist with capable devices
- stmmac:
- fix kernel panic due to NULL pointer dereference of
mdio_bus_data
- fix double clk unprepare when no PHY device is connected
Current release - new code bugs:
- mt76: a few fixes for the recent MT7921 devices and runtime power
management
Previous releases - regressions:
- ice:
- track AF_XDP ZC enabled queues in bitmap to fix copy mode Tx
- fix allowing VF to request more/less queues via virtchnl
- correct supported and advertised autoneg by using PHY
capabilities
- allow all LLDP packets from PF to Tx
- kbuild: quote OBJCOPY var to avoid a pahole call break the build
Previous releases - always broken:
- bpf, lockdown, audit: fix buggy SELinux lockdown permission checks
- mt76: address the recent FragAttack vulnerabilities not covered by
generic fixes
- ipv6: fix KASAN: slab-out-of-bounds Read in
fib6_nh_flush_exceptions
- Bluetooth:
- fix the erroneous flush_work() order, to avoid double free
- use correct lock to prevent UAF of hdev object
- nfc: fix NULL ptr dereference in llcp_sock_getname() after failed
connect
- ieee802154: multiple fixes to error checking and return values
- igb: fix XDP with PTP enabled
- intel: add correct exception tracing for XDP
- tls: fix use-after-free when TLS offload device goes down and back
up
- ipvs: ignore IP_VS_SVC_F_HASHED flag when adding service
- netfilter: nft_ct: skip expectations for confirmed conntrack
- mptcp: fix falling back to TCP in presence of out of order packets
early in connection lifetime
- wireguard: switch from O(n) to a O(1) algorithm for maintaining
peers, fixing stalls and a large memory leak in the process
Misc:
- devlink: correct VIRTUAL port to not have phys_port attributes
- Bluetooth: fix VIRTIO_ID_BT assigned number
- net: return the correct errno code ENOBUF -> ENOMEM
- wireguard:
- peer: allocate in kmem_cache saving 25% on peer memory
- do not use -O3"
* tag 'net-5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
cxgb4: avoid link re-train during TC-MQPRIO configuration
sch_htb: fix refcount leak in htb_parent_to_leaf_offload
wireguard: allowedips: free empty intermediate nodes when removing single node
wireguard: allowedips: allocate nodes in kmem_cache
wireguard: allowedips: remove nodes in O(1)
wireguard: allowedips: initialize list head in selftest
wireguard: peer: allocate in kmem_cache
wireguard: use synchronize_net rather than synchronize_rcu
wireguard: do not use -O3
wireguard: selftests: make sure rp_filter is disabled on vethc
wireguard: selftests: remove old conntrack kconfig value
virtchnl: Add missing padding to virtchnl_proto_hdrs
ice: Allow all LLDP packets from PF to Tx
ice: report supported and advertised autoneg using PHY capabilities
ice: handle the VF VSI rebuild failure
ice: Fix VFR issues for AVF drivers that expect ATQLEN cleared
ice: Fix allowing VF to request more/less queues via virtchnl
virtio-net: fix for skb_over_panic inside big mode
ipv6: Fix KASAN: slab-out-of-bounds Read in fib6_nh_flush_exceptions
fib: Return the correct errno code
...
Some firmware when operation don't may have broken versions leading to
error like the following:
[ 6.176482] Bluetooth: hci0: Firmware revision 0.0 build 121 week 7 2021
[ 6.177906] bluetooth hci0: Direct firmware load for intel/ibt-20-0-0.sfi failed with error -2
[ 6.177910] Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-20-0-0.sfi (-2)
Since we load the firmware file just to check if its version had changed
comparing to the one already loaded we can just skip since the firmware
is already operation.
Fixes: ac0565462e ("Bluetooth: btintel: Check firmware version before
download")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some models of the RTL8822ce utilize a different USB ID. Add this
new one to the Bluetooth driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tty_unregister_ldisc now returns 0 = success. No need to check the
return value. In fact, the users only warned if an error occured and
didn't do anything useful anyway -- the ldisc module was unloaded in any
case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make tty_unregister_ldisc symmetric to tty_register_ldisc by accepting
struct tty_ldisc_ops as a parameter instead of ldisc number. This avoids
checking of the ldisc number bounds in tty_unregister_ldisc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to pass the ldisc number to tty_register_ldisc
separately. Just set it in the already defined tty_ldisc_ops in all the
ldiscs.
This simplifies tty_register_ldisc a bit too (no need to set the num
member there).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Char pointer (cp) passed to tty_ldisc_ops::receive_buf{,2} is const.
There is no reason for flag pointer (fp) not to be too. So switch it in
the definition and all uses.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If
anyone shows up with this hardware, it is trivial to restore
these but we really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios
setting corner cases that loads of drivers got wrong as well
as removing unneeded code due to tty core changes from long
ago that were never propagated out to the drivers
- loads of platform-specific serial port driver updates and
fixes
- coding style cleanups and other small fixes and updates all
over the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa3NQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykMXgCfX3FZgKveI4l94ChXSy4OyKwycHUAn00BzrMC
/7BwA1FnjQnC4zSzuHnm
=bAas
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If anyone
shows up with this hardware, it is trivial to restore these but we
really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios setting
corner cases that loads of drivers got wrong as well as removing
unneeded code due to tty core changes from long ago that were never
propagated out to the drivers
- loads of platform-specific serial port driver updates and fixes
- coding style cleanups and other small fixes and updates all over
the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
serial: extend compile-test coverage
serial: stm32: add FIFO threshold configuration
dt-bindings: serial: 8250: update TX FIFO trigger level
dt-bindings: serial: stm32: override FIFO threshold properties
dt-bindings: serial: add RX and TX FIFO properties
serial: xilinx_uartps: drop low-latency workaround
serial: vt8500: drop low-latency workaround
serial: timbuart: drop low-latency workaround
serial: sunsu: drop low-latency workaround
serial: sifive: drop low-latency workaround
serial: txx9: drop low-latency workaround
serial: sa1100: drop low-latency workaround
serial: rp2: drop low-latency workaround
serial: rda: drop low-latency workaround
serial: owl: drop low-latency workaround
serial: msm_serial: drop low-latency workaround
serial: mpc52xx_uart: drop low-latency workaround
serial: meson: drop low-latency workaround
serial: mcf: drop low-latency workaround
serial: lpc32xx_hs: drop low-latency workaround
...
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/usb/core/hub.c: usb_new_device() contains the following:
/* By default, forbid autosuspend for all devices. It will be
* allowed for hubs during binding.
*/
usb_disable_autosuspend(udev);
So for anything which is not a hub, such as btusb devices, autosuspend is
disabled by default and we must call usb_enable_autosuspend(udev) to
enable it.
This means that the "Fix the autosuspend enable and disable" commit,
which drops the usb_enable_autosuspend() call when the enable_autosuspend
module option is true, is completely wrong, revert it.
This reverts commit 7bd9fb058d.
Cc: Hui Wang <hui.wang@canonical.com>
Fixes: 7bd9fb058d ("Bluetooth: btusb: Fix the autosuspend enable and disable")
Acked-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Proper support for BCM4330 and BMC4334
- Various improvements for firmware download of Intel controllers
- Update management interface revision to 20
- Support for AOSP HCI vendor commands
- Initial Virtio support
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE7E6oRXp8w05ovYr/9JCA4xAyCykFAmBvL7UZHGx1aXoudm9u
LmRlbnR6QGludGVsLmNvbQAKCRD0kIDjEDILKU+eD/4qGiwnwQVia4hjnQ5PZ0c/
sBmZvzzZE43RNRvy8gAwcVLypLaiIkEYml4ruVdF6RGoqaDA6kRB7D0tdk8EtZc4
6h72LX0zefnyZNj/Fcl6+dKuq7bSHjdOK0G+oXFmpvYfScPsI6Oq0ntpYOFYwUE0
cDdeZyb/sW4f6L5AXUgLjD9AIjzlBOJEU5HcRL/uY+E/fH1oe757/IhUDerXjTIh
9EhY28mrI7KeoEcJ1NIgvjPnRCxPRLAKgrzc8NXkUsLeNZSIywrwjgRfTvCZ+qQf
g/MmNv+n7yFlUzA7Fu2d8YAgRtgF9nZc45geqOSHqcSZURORSs0CzEoYinqwT7f0
xdMBi/UoSzJsLksgv+OfXOyoQ4lPNJ47pcH/edmT/ZJ/Ai2yTqUUSODHQ3MLC4Dp
kQj34thQvfTf5b6+9HwKmBjlfMK0QGPqWjp6dth2bzos/ugurDP+XimAv0urvFz+
NkES5kCMUs/1z7Yh+Nj1MyU3Wfdwol0wOh+PXBTAw2fxSy6kmKYGyLw7HEdWegB0
K2w/ZS58g0EGK89ZSiqlZKmXtAd22dQqS6JlZje+9YTtEtRWu+rAF1dddS8vJDjl
Rq3VSQ1B6Qw0rdGpyfxdgm/sWwq5S1YgQQcAZgVaeo9ZiIhfscVD5v5L0Ol6k9ms
3eCK/2brsX0IaV61eVnoOw==
=jiCz
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-04-08' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Proper support for BCM4330 and BMC4334
- Various improvements for firmware download of Intel controllers
- Update management interface revision to 20
- Support for AOSP HCI vendor commands
- Initial Virtio support
====================
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for Bluetooth HCI transport over virtio.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Adding support LE scatternet and WBS for Mediatek Chip
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This skips parsing the firmware version information from the firmware
file while controller is in bootloader mode. As in bootloader mode,
we are supposed to patch unconditionally.
Signed-off-by: Lokendra Singh <lokendra.singh@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In Operational firmware mode, 'Minimum FW version' TLV ID is not available.
So, we cannot fetch already running firmware info for comparison against
another build. However, It can be collected using a combination of other
TLV ID's information.
Signed-off-by: Lokendra Singh <lokendra.singh@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves limited_cce and sbe_type checks under bootloader during tlv parsing
as operational firmware don't have access to these values. Any attempt to read
such values in operational firmware will only fetch garbage data.
Signed-off-by: Lokendra Singh <lokendra.singh@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves duplicated code for waiting firmware download completion to
a function that can be reused.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves duplicated code for waiting firmware download completion to
a function that can be reused.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves version checks of intel_version() to btintel_version_info().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves version checks of intel_version_tlv() to btintel_version_info_tlv().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to allow new firmware to load, it first needs to check if the
firmware version on file matches the one loaded if it doesn't, then it
needs to revert to bootloader mode in order to load the new firmware.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This checks the firmware build number, week and year against the
repective loaded version. If details are a match, skip the download
process.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the missing brcm,bcm4330-bt and brcm,bcm4334-bt to the
match table so device trees can use this compatible as well
and not need to use the fallback brcm,bcm4329-bt.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on device may wakeup status, Bluez stack will enable/disable
passive scanning with whitelist in BT controller while suspending.
As interrupt from BT SoC is handled by UART driver,we need to use
device handle of UART driver to get the status of device may wakeup
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
First, it is never checked. Second, use of it as a debugging aid is
at least questionable. With the current tools, I don't think anyone used
this kind of thing for debugging purposes for years.
On the top of that, e.g. serdev does not set this field of tty_ldisc_ops
at all.
So get rid of this legacy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boot address parameter was not getting updated properly
due to wrong offset
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
print the firmware file name on error loading from fie system
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Obtain and drive the optional reset GPIO line if this is
not hardwired in the platform. This is needed on the
Samsung GT-I9070 mobile phone.
The invers of power is used, this should be OK to apply
simultaneously as the power signal according to
figures 47-51 on pages 159-161 in the BCM4330 datasheet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Warnings: drivers/bluetooth/btusb.c:3775 btusb_mtk_setup() error:
uninitialized symbol 'fw_version'.
-> add initial value for fw_version.
Warnings: sparse: sparse: incorrect type in assignment (different base
types)
-> add le32_to_cpu to fix incorrect type in assignment.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here is the big set of tty/serial driver changes for 5.12-rc1.
Nothing huge, just lots of good cleanups and additions:
- Your n_tty line discipline cleanups
- vt core cleanups and reworks to make the code more "modern"
- stm32 driver additions
- tty led support added to the tty core and led layer
- minor serial driver fixups and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYCqgqw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJYQCgnxHmkhzJ2VarTDR3cWm1gu0NU7AAoNe5wWUh
4TQbhB9LSNo78HnIVze0
=Chcg
-----END PGP SIGNATURE-----
Merge tag 'tty-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver changes for 5.12-rc1.
Nothing huge, just lots of good cleanups and additions:
- n_tty line discipline cleanups
- vt core cleanups and reworks to make the code more "modern"
- stm32 driver additions
- tty led support added to the tty core and led layer
- minor serial driver fixups and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (54 commits)
serial: core: Remove BUG_ON(in_interrupt()) check
vt_ioctl: Remove in_interrupt() check
dt-bindings: serial: imx: Switch to my personal address
vt: keyboard, use new API for keyboard_tasklet
serial: stm32: improve platform_get_irq condition handling in init_port
serial: ifx6x60: Remove driver for deprecated platform
tty: fix up iterate_tty_read() EOVERFLOW handling
tty: fix up hung_up_tty_read() conversion
tty: fix up hung_up_tty_write() conversion
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
serial: remove sirf prima/atlas driver
serial: mxs-auart: Remove <asm/cacheflush.h>
serial: mxs-auart: Remove serial_mxs_probe_dt()
serial: fsl_lpuart: Use of_device_get_match_data()
dt-bindings: serial: renesas,hscif: Add r8a779a0 support
tty: serial: Drop unused efm32 serial driver
...
If BT SoC is running with ROM FW then just return in
qca_suspend function as ROM FW does not support
in-band sleep.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This issue starts from linux-5.10-rc1, I reproduced this issue on my
Dell Inspiron 7447 with BT adapter 0cf3:e005, the kernel will print
out: "Bluetooth: hci0: don't support firmware rome 0x31010000", and
someone else also reported the similar issue to bugzilla #211571.
I found this is a regression introduced by 'commit b40f58b973
("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support"), the
patch assumed that if high ROM version is not zero, it is an adapter
on WCN6855, but many old adapters don't need to load rampatch or nvm,
and they have non-zero high ROM version.
To fix it, let the driver match the rom_version in the
qca_devices_table first, if there is no entry matched, check the
high ROM version, if it is not zero, we assume this adapter is ready
to work and no need to load rampatch and nvm like previously.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211571
Fixes: b40f58b973 ("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enlarging the size of 'struct btmtk_hci_wmt_cmd' makes it no longer
fit on the kernel stack, as seen from this compiler warning:
drivers/bluetooth/btusb.c:3365:12: error: stack frame size of 1036 bytes in function 'btusb_mtk_hci_wmt_sync' [-Werror,-Wframe-larger-than=]
Change the function to dynamically allocate the buffer instead.
As there are other sleeping functions called from the same location,
using GFP_KERNEL should be fine here, and the runtime overhead should
not matter as this is rarely called.
Unfortunately, I could not figure out why the message size is
increased in the previous patch. Using dynamic allocation means
any size is possible now, but there is still a range check that
limits the total size (including the five-byte header) to 255
bytes, so whatever was intended there is now undone.
Fixes: 48c13301e6 ("Bluetooth: btusb: Fine-tune mt7663 mechanism.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix follow warning:
drivers/bluetooth/btusb.c:3479:9: warning: variable ‘fw_size’ set but not used [-Wunused-but-set-variable]
size_t fw_size;
^~~~~~~
drivers/bluetooth/btusb.c:3473:29: warning: variable ‘patchhdr’ set but not used [-Wunused-but-set-variable]
struct btmtk_patch_header *patchhdr = NULL;
^~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
I tried to disable the autosuspend on btusb through the module
parameter enable_autosuspend, this parameter is set to N, but the usb
bluetooth device is still runtime suspended.
$ cat /sys/module/btusb/parameters/enable_autosuspend
N
$ cat /sys/bus/usb/devices/3-10/power/runtime_status
suspended
$ cat /sys/bus/usb/devices/3-10/power/runtime_suspended_time
65187
We already set ".supports_autosuspend = 1" in the usb_driver, this
device will be set autosuspend enabled by usb core, we don't need
to call usb_enable_autosuspend() in the btusb_probe(). Instead if
users set the parameter enable_autosuspend to N, we need to call
usb_disable_autosuspend() in the btusb_probe(). After this change
and set the parameter to N, we could see the device is not runtime
suspended anymore.
$ cat /sys/module/btusb/parameters/enable_autosuspend
N
$ cat /sys/bus/usb/devices/3-10/power/runtime_status
active
$ cat /sys/bus/usb/devices/3-10/power/runtime_suspended_time
0
And if we disable the autosuspend in the btusb_probe(), we need to
enable the autosuspend in the disconnect(), this could guarantee
that the device could be runtime suspended after we rmmod the btusb.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In btusb_mtk_wmt_recv if skb_clone fails, the alocated skb should be
released.
Omit the labels “err_out” and “err_free_skb” in this function
implementation so that the desired exception handling code
would be directly specified in the affected if branches.
Fixes: a1c49c434e ("btusb: Add protocol support for MediaTek MT7668U USB devices")
Signed-off-by: Jupeng Zhong <zhongjupeng@yulong.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fine-tune read register for mt7663/mt7921.
For mediatek chip spcific wmt protocol, we add more delay to send EP0
In-Token.
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA_IBS_DISABLED flag will be set after memorydump started from
controller.Currently qca_suspend() is waiting for SSR to complete
based on flag QCA_IBS_DISABLED.Added to check for QCA_SSR_TRIGGERED
flag too.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By this change, it will enable WBS supported on the specific Realtek BT
devices, such as RTL8822C and RTL8852A.
In the future, it's able to maintain what the Realtek devices support WBS
here.
Tested-by: Hilda Wu <hildawu@realtek.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Realtek Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixes both the "splice/sendfile to a tty" and "splice/sendfile from a
tty" regression from 5.10.
* 'tty-splice' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
tty: implement write_iter
The tty line discipline .read() function was passed the final user
pointer destination as an argument, which doesn't match the 'write()'
function, and makes it very inconvenient to do a splice method for
ttys.
This is a conversion to use a kernel buffer instead.
NOTE! It does this by passing the tty line discipline ->read() function
an additional "cookie" to fill in, and an offset into the cookie data.
The line discipline can fill in the cookie data with its own private
information, and then the reader will repeat the read until either the
cookie is cleared or it runs out of data.
The only real user of this is N_HDLC, which can use this to handle big
packets, even if the kernel buffer is smaller than the whole packet.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During SSR after memory dump collection,BT controller will be powered off,
powered on and then FW will be downloaded.During suspend if BT controller
is powered off due to SSR then we should wait until SSR is completed and
then suspend.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When __le32_to_cpu() fails, qca_memdump should be freed
just like when vmalloc() fails.
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RTL8723DS could be handled by btrtl-driver, so add ability to bind it
using device tree.
Signed-off-by: John-Eric Kamps <johnny86@gmx.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btrtl_dev->ic_info is only available from the controller on cold boot
(the lmp subversion matches the device model and this is used to look up
the ic_info). On warm boots (firmware already loaded),
btrtl_dev->ic_info is null.
Fixes: 05672a2c14 (Bluetooth: btrtl: Enable central-peripheral role)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable the central-peripheral role on RTL8822CE. This enables creating
connections while there is an existing connection in the slave role.
This change can be confirmed in userspace via `bluetoothctl show` which
will now show "Roles: central-peripheral".
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit a63f23c9d139377833a139b179793fea79ee198f.
get_unaligned_{le16|le32|le64}(p) is meant to replace code of the form
le16_to_cpu(get_unaligned((__le16 *)p)). There is no need to explicitly
do leXX_to_cpu() if get_unaligned_leXX() is used.
https://lwn.net/Articles/277779/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables bcm driver to properly handle ISO packets.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Realtek RTL8822CE Bluetooth controller support Microsoft vendor
extension and it uses 0xFCF0 for VsMsftOpCode.
The following test step was performed.
- Boot the test device with RTL8822CE and verify the INFO print in
dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel JeffersonPeak, HarrisonPeak and CyclonePeak Bluetooth
controllers support the Microsoft vendor extension and they are using
0xFC1E for VsMsftOpCode.
< HCI Command: Vendor (0x3f|0x001e) plen 1
00
> HCI Event: Command Complete (0x0e) plen 15
Vendor (0x3f|0x001e) ncmd 1
Status: Success (0x00)
00 3f 00 00 00 00 00 00 00 01 50
The following test step was performed.
- Boot the test devices with HarrisonPeak and verify INFO print in
dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The following Qualcomm WCN399x Bluetooth controllers support the
Microsoft vendor extension and they are using 0xFD70 for VsMsftOpCode.
-WCN3990
-WCN3991
-WCN3998
< HCI Command: ogf 0x3f, ocf 0x0170, plen 1
00
> HCI Event: 0x0e plen 18
01 70 FD 00 00 1F 00 00 00 00 00 00 00 04 4D 53 46 54
The following test step was performed.
- Boot the device with WCN3991 and verify INFO print in dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
we should send hci reset command before bt turn off, which can reset bt
firmware status.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In hci_uart_write_work, there is a loop/goto checking the value of
HCI_UART_TX_WAKEUP. If HCI_UART_TX_WAKEUP is set again, it keeps trying
hci_uart_dequeue; otherwise, it clears HCI_UART_SENDING and returns.
In hci_uart_tx_wakeup, if HCI_UART_SENDING is already set, it sets
HCI_UART_TX_WAKEUP, skips schedule_work and assumes the running/pending
hci_uart_write_work worker will do hci_uart_dequeue properly.
However, if the HCI_UART_SENDING check in hci_uart_tx_wakeup is done after
the loop breaks, but before HCI_UART_SENDING is cleared in
hci_uart_write_work, the schedule_work is skipped incorrectly.
Fix this race by changing the order of HCI_UART_SENDING and
HCI_UART_TX_WAKEUP modification.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 82f5169bf3 ("Bluetooth: hci_uart: add serdev driver support library")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to read FW build version from debugfs node.
This info can be read from
/sys/kernel/debug/bluetooth/hci0/firmware_info
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When alt mode 6 is not available, fallback to the kernel <= 5.7 behavior
of always using alt mode 1.
Prior to kernel 5.8, btusb would always use alt mode 1 for WBS (Wide
Band Speech aka mSBC aka transparent SCO). In commit baac6276c0
("Bluetooth: btusb: handle mSBC audio over USB Endpoints") this
was changed to use alt mode 6, which is the recommended mode in the
Bluetooth spec (Specifications of the Bluetooth System, v5.0, Vol 4.B
§2.2.1). However, many if not most BT USB adapters do not support alt
mode 6. In fact, I have been unable to find any which do.
In kernel 5.8, this was changed to use alt mode 6, and if not available,
use alt mode 0. But mode 0 has a zero byte max packet length and can
not possibly work. It is just there as a zero-bandwidth dummy mode to
work around a USB flaw that would prevent device enumeration if
insufficient bandwidth were available for the lowest isoc mode
supported.
In effect, WBS was broken for all USB-BT adapters that do not support
alt 6, which appears to nearly all of them.
Then in commit 461f95f04f ("Bluetooth: btusb: USB alternate setting 1 for
WBS") the 5.7 behavior was restored, but only for Realtek adapters.
I've tested a Broadcom BRCM20702A and CSR 8510 adapter, both work with
the 5.7 behavior and do not with the 5.8.
So get rid of the Realtek specific flag and use the 5.7 behavior for all
adapters as a fallback when alt 6 is not available. This was the
kernel's behavior prior to 5.8 and I can find no adapters for which it
is not correct. And even if there is an adapter for which this does not
work, the current behavior would be to fall back to alt 0, which can not
possibly work either, and so is no better.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some resource should be released in the error handling path of the probe
function, as already done in the remove function.
The remove function was fixed in commit 5052de8def ("soc: qcom: smd:
Transition client drivers from smd to rpmsg")
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the recent btusb change to detect and deal with more fake CSR
controllers, I decided to see if fake CSR controllers with Barrot
8041a02 chips would now work.
After much experimentation I came to the conclusion that it works, if I
have autosuspend enabled initially and then disable it after the device
has suspended at least once. Yes this is very weird, but I've tried many
things, like manually clearing the remote-wakeup feature. Doing a
runtime-resume + runtime suspend is the only way to get the receiver
to actually report received data (and/or pairing info) through its
bulk rx endpoint.
But the funkyness of the bulk-endpoint does not stop there, I mainly
found out about this problem, because with autosuspend enabled
(which usually ensures the suspend at least once condition is met),
the receiver stops reporting received data through its bulk rx endpoint
as soon as autosuspend kicks in. So I initially just disabled
autosuspend, but then the receiver does not work at all.
This was with a fake CSR receiver with a Barrot 8041a02 chip with a
bcdDevice value of 0x8891, a lmp_subver of 0x1012, a hci_rev of 0x0810
and a hci_ver of BLUETOOTH_VER_4_0.
Summarizing this specific fake CSR receiver has the following 2 issues:
1. The bulk rx endpoint will never report any data unless
the device was suspended at least once.
2. They will not wakeup when autosuspended and receiving data on their
bulk rx endpoint from e.g. a keyboard or mouse (IOW remote-wakeup support
is broken for the bulk endpoint).
Add a workaround for 1. which enables runtime-suspend, force-suspends
the hci and then wakes-it up by disabling runtime-suspend again.
Add a workaround for 2. which clears the hci's can_wake flag, this way
the hci will still be autosuspended when it is not open.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Commit cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the
Chinese Bluetooth controllers") made the detection of fake controllers
more generic fixing it for much of the newer fakes / clones.
But this does not work for a fake CSR controller with a bcdDevice
value of 0x0134, which was correctly identified as fake before
this change.
Add an extra check for this special case, checking for a combination
of a bcdDevice value of 0x0134, together with a lmp_subver of 0x0c5c
and a hci_ver of BLUETOOTH_VER_2_0.
The chip inside this fake dongle is marked as with "clockwise cw6629d".
Fixes: cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
we define many nvm files for wcn6855 btsoc and host driver
should find the correct nvm file based on board ID and then
download it.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define a helper function to download firmware for new generation Intel
controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define a new function to construct firmware/ddc filename for new
generation Intel controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define a new *setup* function for new generation Intel controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Sathish Narasimman <Sathish.Narasimman@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
do __le32_to_cpu to tlv data fields to make sure driver runs
correctly when running on big endian system.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
mtk_setup_firmware() misses to call release_firmware() in an error
path. Jump to free_fw to fix it.
Fixes: 737cd06072 ("Bluetooth: btmtksdio: fix up firmware download sequence")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
btusb_mtk_setup_firmware() misses to call release_firmware() in an error
path. Jump to err_release_fw to fix it.
Fixes: f645125711 ("Bluetooth: btusb: fix up firmware download sequence")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This change will allow to use different NVM file based
on WCN3991 BT SoC ID.Need to use different NVM file based on
fab location for WCN3991 BT SoC.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add OBDA0623 ACPI HID to the acpi_device_id table. This HID is used
for the RTL8723BS Bluetooth part on the Acer Switch 10E SW3-016.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1665610
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There have been multiple revisions of the patch fix the h5->rx_skb
leak. Accidentally the first revision (which is buggy) and v5 have
both been merged:
v1 commit 70f259a3f4 ("Bluetooth: hci_h5: close serdev device and free
hu in h5_close");
v5 commit 855af2d74c ("Bluetooth: hci_h5: fix memory leak in h5_close")
The correct v5 makes changes slightly higher up in the h5_close()
function, which allowed both versions to get merged without conflict.
The changes from v1 unconditionally frees the h5 data struct, this
is wrong because in the serdev enumeration case the memory is
allocated in h5_serdev_probe() like this:
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
So its lifetime is tied to the lifetime of the driver being bound
to the serdev and it is automatically freed when the driver gets
unbound. In the serdev case the same h5 struct is re-used over
h5_close() and h5_open() calls and thus MUST not be free-ed in
h5_close().
The serdev_device_close() added to h5_close() is incorrect in the
same way, serdev_device_close() is called on driver unbound too and
also MUST no be called from h5_close().
This reverts the changes made by merging v1 of the patch, so that
just the changes of the correct v5 remain.
Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently qca_suspend() is relied on IBS mechanism. During
FW download and memory dump collections, IBS will be disabled.
In those cases, driver will allow suspend and still uses the
serdev port, which results to errors. Now added a wait timeout
if suspend is triggered during FW download and memory collections.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the check for a failed bt_skb_alloc allocation is incorrectly
checking using IS_ERR and this can lead to a null pointer dereference. Fix
this by checking for a null pointer return using the !skb idiom.
Addresses-Coverity: ("Dereference null return")
Fixes: 1996d9cad6 ("Bluetooth: btrtl: Ask 8821C to drop old firmware")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using the wl1271 Bluetooth function of am335x, it is found that the
Bluetooth module cannot respond in time after Bluetooth is enabled, and
a small delay is needed to work normally, so whether to add a small
mdelay.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace symbolic permissions with octal values. Use usleep_range
for small msec values due to the fact that msleep() less than
20ms may have unexpected behavior/sleep longer.
- https://lkml.org/lkml/2016/8/2/1945
- Documentation/timers/timers-howto.rst
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently driver only retries to download FW if FW downloading
is failed. Sometimes observed command timeout for version request
command, if this happen on some platforms during boot time, then
a reboot is needed to turn ON BT. Instead to avoid a reboot, now
extended retry logic for version request command too.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When h5_close() is called, h5 is directly freed when !hu->serdev.
However, h5->rx_skb is not freed, which causes a memory leak.
Freeing h5->rx_skb and setting it to NULL, fixes this memory leak.
Fixes: ce945552fd ("Bluetooth: hci_h5: Add support for serdev enumerated devices")
Reported-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com
Tested-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some platforms keep USB power even when they are powered off and in S5,
this makes Realtek 8821C keep its firmware even after a cold boot, and
make 8821C never load new firmware.
So use vendor specific HCI command to ask 8821C drop its firmware after
system shutdown.
Newer firmware doesn't have this issue so we only use this trick for old
8821C firmware version.
Suggested-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enhance the ic_id_table that it's able to maintain regularly.
To judge which chip should be initialized by LMP subversion, HCI revision,
HCI version and HCI bus which were given in the ic_id_table.
Also, refine the incorrect LMP subversion of ROM for RTL8723D and
RTL8723A.
Suggested-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports connectable advertisements so we need to add the valid
le states quirk so the 'central-peripheral' role is exposed in
userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAl+ItRwACgkQMUZtbf5S
IrtTMg//UxpdR/MirT1DatBU0K/UGAZY82hV7F/UC8tPgjfHZeHvWlDFxfi3YP81
PtPKbhRZ7DhwBXefUp6nY3UdvjftrJK2lJm8prJUPSsZRye8Wlcb7y65q7/P2y2U
Efucyopg6RUrmrM0DUsIGYGJgylQLHnMYUl/keCsD4t5Bp4ksyi9R2t5eitGoWzh
r3QGdbSa0AuWx4iu0i+tqp6Tj0ekMBMXLVb35dtU1t0joj2KTNEnSgABN3prOa8E
iWYf2erOau68Ogp3yU3miCy0ZU4p/7qGHTtzbcp677692P/ekak6+zmfHLT9/Pjy
2Stq2z6GoKuVxdktr91D9pA3jxG4LxSJmr0TImcGnXbvkMP3Ez3g9RrpV5fn8j6F
mZCH8TKZAoD5aJrAJAMkhZmLYE1pvDa7KolSk8WogXrbCnTEb5Nv8FHTS1Qnk3yl
wSKXuvutFVNLMEHCnWQLtODbTST9DI/aOi6EctPpuOA/ZyL1v3pl+gfp37S+LUTe
owMnT/7TdvKaTD0+gIyU53M6rAWTtr5YyRQorX9awIu/4Ha0F0gYD7BJZQUGtegp
HzKt59NiSrFdbSH7UdyemdBF4LuCgIhS7rgfeoUXMXmuPHq7eHXyHZt5dzPPa/xP
81P0MAvdpFVwg8ij2yp2sHS7sISIRKq17fd1tIewUabxQbjXqPc=
=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, and they can handle data off
of the stack, so move the driver over to using those calls instead,
saving some logic when dynamically allocating memory.
v2: changed API of use usb_control_msg_send() and usb_control_msg_recv()
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-15-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QCA Rome supports wide band speech, this patch enables the wide band
speech support by set the BTUSB_WIDEBAND_SPEECH flag.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, and they can handle data off
of the stack, so move the driver over to using those calls instead,
saving some logic when dynamically allocating memory.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New generation controllers supports ECDSA secure boot engine.
This patch adds,
1) function to send ECDSA header
2) function to download complete firmware for new generation Intel
controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
New generation Intel controllers returns version information in TLV
format. This patch adds,
1) Enums, structures for TLV
2) function to read controller information, parse TLV data and populate
intel_version_tlv structure
3) function to print version information
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Split firmware download code into two functions - one to download
header and other to download payload. This patch enhances readability
and reusabiltiy of code
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Sathish Narasimman <Sathish.Narasimman@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During serdev unregister, hdev->shutdown is called before
proto close. Removing duplicates power OFF call.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_QUIRK_NON_PERSISTENT_SETUP is set by drivers,
it indicates that BT SoC will be completely powered OFF
during BT OFF. On next BT ON firmware must be downloaded
again. Holding UART port open during BT OFF is draining
the battery. Now during BT OFF, UART port is closed if
qurik HCI_QUIRK_NON_PERSISTENT_SETUP is set by clearing
HCI_UART_PROTO_READY proto flag. On next BT ON, UART
port is opened if HCI_UART_PROTO_READY proto flag is cleared.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On new Intel platform the device is provided with INT33E3 ID.
Append it to the list.
This will require ACPI_GPIO_QUIRK_ONLY_GPIOIO to be enabled because
the relevant ASL looks like:
UartSerialBusV2 ( ... )
GpioInt ( ... ) { ... }
GpioIo ( ... ) { ... }
which means that first GPIO resource is an interrupt, while we are expecting it
to be reset one (output). Do the same for host-wake because in case of
GpioInt() the platform_get_irq() will do the job and should return correct
Linux IRQ number. That said, host-wake GPIO can only be GpioIo() resource.
While here, drop commas in terminator lines.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no need to have list_for_each() followed by list_entry()
when we simply may use list_for_each_entry() directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sparse rightfully complains:
hci_intel.c:696:26: warning: cast to restricted __le16
hci_intel.c:701:26: warning: cast to restricted __le16
hci_intel.c:702:26: warning: cast to restricted __le16
hci_intel.c:703:26: warning: cast to restricted __le16
hci_intel.c:725:26: warning: cast to restricted __le16
hci_intel.c:730:26: warning: cast to restricted __le16
hci_intel.c:731:26: warning: cast to restricted __le16
hci_intel.c:732:26: warning: cast to restricted __le16
because we access non-restricted types with le16_to_cpu().
More confusion is added by using above against u8. On big-endian
architecture we will get all zeroes. I bet it's not what should be
in such case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Because clk_disable_unprepare already checked
NULL clock parameter, so the additional check is
unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When kmalloc() on buf fails, urb should be freed just like
when kmalloc() on dr fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
boot parameter gets updated during firmware download process. Use the
updated boot parameter while doing soft reset of controller. This patch
fixes updating of boot parameter.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
