After initial start-up, the driver triggers ATI (calibration) with
the newly loaded register configuration in place. Next, the driver
polls a register field to ensure ATI completed in a timely fashion
and that the device is ready to sense.
However, communicating with the device over I2C while ATI is under-
way may induce noise in the device and cause ATI to fail. As such,
the vendor recommends not to poll the device during ATI.
To solve this problem, let the device naturally signal to the host
that ATI is complete by way of an interrupt. A completion prevents
the device from successfully probing until this happens.
As an added benefit, initial switch states are now reported in the
interrupt handler at the same time ATI status is checked. As such,
duplicate code that reports initial switch states has been removed
from iqs269_input_init().
The former logic that scaled ATI timeout and filter settling delay
is not carried forward with the new implementation, as it produces
overly conservative delays at the lower clock rate.
Rather, a single timeout that covers both clock rates is used. The
filter settling delay does not happen to be necessary and has been
removed as well.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7RtB2T7AF9rYMjK@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Polling the device while it transitions from automatic to manual
power mode switching may keep the device from actually finishing
the transition. The process appears to time out depending on the
polling rate and the device's core clock frequency.
This is ultimately unnecessary in the first place; instead it is
sufficient to write the desired mode during initialization, then
disable automatic switching at suspend. This eliminates the need
to ensure the device is prepared for a manual change and removes
the 'suspend_mode' variable.
Similarly, polling the device while it transitions from one mode
to another under manual control may time out as well. This added
step does not appear to be necessary either, so drop it.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs+eEXlRw4Vq57@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unless it is being done as part of servicing a soft reset interrupt,
configuring channels on-the-fly (as is the case when writing to the
ati_trigger attribute) may cause GPIO3 (which reflects the state of
touch for a selected channel) to be inadvertently asserted.
To solve this problem, follow the vendor's recommendation and write
all channel configuration as well as the REDO_ATI register field as
part of a single block write. This ensures the device has been told
to re-calibrate itself following an I2C stop condition, after which
sensing resumes and GPIO3 may be asserted.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs8GyV7g0nF5Yy@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The time the device takes to deassert its RDY output following an
I2C stop condition scales with the core clock frequency.
To prevent level-triggered interrupts from being reasserted after
the interrupt handler returns, increase the time before returning
to account for the worst-case delay (~140 us) plus margin.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs484ypy4dab5G@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Each call to device/fwnode_get_named_child_node() must be matched
with a call to fwnode_handle_put() once the corresponding node is
no longer in use. This ensures a reference count remains balanced
in the case of dynamic device tree support.
Currently, the driver does not call fwnode_handle_put() on nested
event nodes. This patch solves this problem by adding the missing
instances of fwnode_handle_put().
As part of this change, the logic which parses each channel's key
code is gently refactored in order to reduce the number of places
from which fwnode_handle_put() is called.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/Y7Rsx68k/gvDVXAt@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
SIMPLE_DEV_PM_OPS() is deprecated as it requires explicit protection
against unused function warnings. The new combination of pm_sleep_ptr()
and DEFINE_SIMPLE_DEV_PM_OPS() allows the compiler to see the functions,
thus suppressing the warning, but still allowing the unused code to be
removed. Thus also drop the __maybe_unused markings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230102181842.718010-9-jic23@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
