Looking at the ADF code from the Android kernel sources for a
cherrytrail tablet I noticed that it is calling the
MIPI_SEQ_ASSERT_RESET sequence from the panel prepare hook.
Until commit b1cb1bd291 ("drm/i915/dsi: update reset and power sequences
in panel prepare/unprepare hooks") the mainline i915 code was doing the
same. That commits effectively swaps the calling of MIPI_SEQ_ASSERT_RESET /
MIPI_SEQ_DEASSERT_RESET.
Looking at the naming of the sequences that is the right thing to do,
but the problem is, that the old mainline code and the ADF code was
actually calling the right sequence (tested on a cube iwork8 air tablet),
and the swapping of the calling breaks things.
This breakage was likely not noticed in testing because on cherrytrail,
currently chv_exec_gpio ends up disabling the gpio pins rather then
setting them (this is fixed in the next patch in this patch-set).
This commit fixes the swapping by fixing MIPI_SEQ_ASSERT/DEASSERT_RESET's
places in the enum defining them, so that their (new) names match their
actual use.
Changes in v2:
-Add a comment to the enum explaining that the assert/reassert names
are swapped in the spec
Fixes: b1cb1bd291 ("drm/i915/dsi: update reset and power sequences...")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161202150128.29871-1-hdegoede@redhat.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 2b8208ac93)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For dual link panel scenarios there are new fields added in the
VBT which indicate on which port the PWM cntrl and CABC ON/OFF
commands needs to be sent.
v2: Moving the comment to intel_dsi.h(Jani)
v3: Renaming the field names (Jani)
v4 by Jani: make this patch only about VBT
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459346623-30752-2-git-send-email-jani.nikula@intel.com
We've been accumulating code across the driver that depends on the VBT
specific structures and defines. The VBT is an uncontrollable
beast. Encourage encapsulation of the VBT data by hiding the structures
and defines in a private header only to be included from intel_bios.c.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-7-git-send-email-jani.nikula@intel.com
Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT and DEVICE_TYPE_DIGITAL_OUTPUT when
trying to determine the presence of eDP based on the VBT child device
type. Apparently a significant portion of VLV systems have these bits
set incorrectly, and so we currently fail to detect eDP on said systems.
This is based on an earlier patch [1] from Andreas Lampersperger.
Instead of ignoring the bits just on VLV as was done in the orignal
patch, we now ignore them for all platforms. We should still have
enough bits in there to avoid false positives (unless the VBT is totally
bonkers).
Quoting the orignal patch:
> When the i915.ko identify an eDP output on a valleyview
> board, it should be more slackly. The reason for that is,
> that BIOS DATA TABLES generated with intel BMP (Binary
> Modification Program) do not set bits for NOT_HDMI or
> DIGITAL_OUTPUT on the device type. Due to Adolfo
> Sanchez from Intel EMGD, this is not possible.
> To solve this problem and enable i915.ko on embedded
> vlv boards with eDP, we ignore this two bits.
[1] http://lists.freedesktop.org/archives/intel-gfx/2015-June/069416.html
Cc: Andreas Lampersperger <lampersperger.andreas@heidenhain.de>
Cc: "Sanchez, AdolfoX" <adolfox.sanchez@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers exist only before GEN5, so currently we may access
undefined registers on VLV/CHV and BXT. Apply the workaround only pre
GEN5.
Since the workaround is relevant only when LVDS is present, for clarity
apply it only if this is the case.
This triggered an unclaimed register access warning on BXT.
v2: (Ville)
- move the workaround to the LVDS init code
- print a debug note about the workaround
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable eDP on DDI-E.
Also let's remove duplicated definitions to avoid later confusion.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are OEMs using DDI-E out there,
so let's enable it.
Unfortunately there is no detection bit for DDI-E
So we need to rely on VBT for that.
I also need to give credits to Xiong since before seing
his approach to check info->support_* I was creating an ugly
vbt->ddie_sfuse_strap in order to propagate the ddi presence info
v2: Rebased as last patch in the series. since all other patches
in this series are needed for anything working propperly on DDI-E.
Credits-to: "Zhang, Xiong Y" <xiong.y.zhang@intel.com>
Cc: "Zhang, Xiong Y" <xiong.y.zhang@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
VBT version 196 increased the size of common_child_dev_config. The
parser code assumed that the size of this structure would not change.
The modified code now copies the amount needed based on the VBT version,
and emits a debug message if the VBT version is unknown (too new); since
the struct config block won't shrink in newer versions it should be
harmless to copy the maximum known size in such cases, so that's what we
do, but emitting the warning is probably sensible anyway.
In the longer run it might make sense to modify the parser code to use a
version/feature mapping, rather than hardcoding things like this, but
for now the variants are fairly manageable.
This fixes a regression introduced in
commit 75067ddecf
Author: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Date: Fri Jul 10 14:10:55 2015 +0300
drm/i915: Per-DDI I_boost override
since that commit changed the child device config size without updating
the checks and memcpy.
v2: Stricter size checks
v3 by Jani:
- Keep the checks strict, and warnigns verbose, but keep going anyway.
- Take care to copy the max amount of child device config we can.
- Fix the messages.
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The CRC (Crystal Cove) PMIC, controls the panel enable and disable
signals for BYT for dsi panels. This is indicated in the VBT fields. Use
that to initialize and use GPIO based control for these signals.
v2: Use the newer gpiod interface(Alexandre)
v3: Remove the redundant checks and unused code (Ville)
v4: Moved PWM vs SoC backlight #defines to intel_bios.h (Jani)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Recent BSW VBT has a VBT child device size 37 bytes instead of the 33
bytes our code assumes. This means we fail to parse the VBT and thus
fail to detect eDP ports properly and just register them as DP ports
instead.
Fix it up by using the reported child device size from the VBT instead
of assuming it matches out struct defintions.
The latest spec I have shows that the child device size should be 36
bytes for rev >= 195, however on my BSW the size is actually 37 bytes.
And our current struct definition is 33 bytes.
Feels like the entire VBT parses would need to be rewritten to handle
changes in the layout better, but for now I've decided to do just the
bare minimum to get my eDP port back.
Cc: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Adding VBT version check for low_vswing field, and correcting parsing
v3: (Damien)
- Restrain the scope of the 'vswing' variable
- Use the more idiomatic "ev_priv->vbt.edp_low_vswing = vswing == 0;"
instead of if (foo) var = true; else var = false;
- Shorten edp_vswing_premph_setting to edp_vswing_premph to fit in 80 chars
- Add the version from which the edp_vswing_premph field is valid in the
struct definition
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 371abae844.
This data seems unreliable and causing many issues and blocking other
teams and feature implementation. Safest way is to revert that for now.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88081
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88039
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87671
Cc: Vandana Kannan <vandana.kannan@intel.com>
Cc: Deepak M <m.deepak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Kristian Høgsberg <hoegsberg@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LFP brighness control from the VBT block 43 indicates which
controller is used for brightness.
LFP1 brightness control method:
Bit 7-4 = This field controller number of the brightnes controller.
0 = Controller 0
1 = Controller 1
2 = Controller 2
3 = Controller 3
Others = Reserved
Bits 3-0 = This field specifies the brightness control pin to be used on the
platform.
0 = PMIC pin is used for brightness control
1 = LPSS PWM is used for brightness control
2 = Display DDI is used for brightness control
3 = CABC method to control brightness
Others = Reserved
Adding the above fields in dev_priv->vbt and corresponding changes in
parse_backlight()
v2: Jani's review comments addressed
- Move PWM definitions to intel_bios.h
- Moving vbt_version to intel_vbt_data
- Rename brightness to bl_ctrl_data
- Logging just control_pin instead of string
- Avoid adding vbt_version in dev_priv
- Since only DDI option is available as of now, let control pin DDI
affect dev_priv->vbt.backlight.present
v3: Jani's review comments addressed
- Drop control_pin
- Use bdb->version
- set controller to 0 instead of using control pin define
- check controller bounds
- remove superfluous changes in intel_parse_bios
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.
v2 : Address review comments by Jani
- Removed the bit mask used for ->dual_link
- Used DSI instead of MIPI for #define variables
v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PSR (aka SRD) block is defined at VBT and currently being used.
Mainly/At-least to configure the amount of idle_frames require to get
back to PSR Entry.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This does not seem to make a difference for the structs in question, but
document the intent.
v2: also pack union child_device_config (Daniel)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Updated the error log as suggested by Imre
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems by default the VBT has MIPI configuration block as well. The
Generic driver will assume always MIPI if MIPI configuration block is found.
This is causing probelm when actually there is eDP. Fix this by looking
into general definition block which will have device configurations. From here
we can figure out what is the LFP type and initialize MIPI only if MIPI
is found.
v2: Addressed review comments by Damien
- Moved PORT definitions to intel_bios.h and renamed as DVO_PORT_MIPIA
- renamed is_mipi to has_mipi and moved definition as suggested
- Check has_mipi inside parse_mipi and intel_dsi_init insted of outside
v3: Make has_mipi as a bitfield as suggested
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: fold in conditions to pack everything neatly below 80 chars.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
The parser extracts the config block(#52) and sequence(#53) data
and store in private data structures.
v2: Address review comments by Jani
- adjust code for the structure changes for bdb_mipi_config
- add boundry and buffer overflow checks as suggested
- use kmemdup instead of kmalloc and memcpy
v3: More strict check while parsing VBT
- Ensure that at anytime we do not go beyond sequence block
while parsing
- On unknown element fail the whole parsing
v4: Style changes and spell check mostly as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only supported types are none and PWM. Other values are obsolete or
reserved, don't add them.
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch reads the DRRS support and Mode type from VBT fields.
The read information will be stored in VBT struct during BIOS
parsing. The above functionality is needed for decision making
whether DRRS feature is supported in i915 driver for eDP panels.
This information helps us decide if seamless DRRS can be done
at runtime to support certain power saving features. This patch
was tested by setting necessary bit in VBT struct and merging
the new VBT with system BIOS so that we can read the value.
v2: Incorporated review comments from Chris Wilson
Removed "intel_" as a prefix for DRRS specific declarations.
v3: Incorporated Jani's review comments
Removed function which deducts drrs mode from panel_type. Modified some
print statements. Made changes to use DRRS_NOT_SUPPORTED as 0 instead of -1.
v4: Incorporated Jani's review comments.
Modifications around setting vbt drrs_type.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
[danvet: Drop the misleading/redundant comment about the added drrs
field in the vbt struct as discussed with Jani on irc.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MIPI Block #52 which provides configuration details for the MIPI panel
including dphy settings as per panel and tcon specs
Block #53 gives information on panel enable sequences
v2: Address review comemnts from Jani
- Move panel ids from intel_dsi.h to intel_bios.h
- bdb_mipi_config structure improvements for cleaner code
- Adding units for the pps delays, all in ms
- change data structure to be more cleaner and simple
v3: Corrected the unit for pps delays as 100us
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't actually do anything with the information yet, but parse and
log what's in the VBT.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checkpatch tells me
WARNING: __packed is preferred over __attribute__((packed))
so switch over to __packed across the driver before adding new packed
structs.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the bits in the VBT child device type have some speciifc meaning,
so looking for an exact match isn't always the right thing. On some
VLVs for example the device type for eDP panels is 0x1806.
If we mask out the bits that could concievably change between different
eDP panels, we are left with the set of bits that should still
tell us if the port is eDP or not.
v2: Use the named bits for VBT child device type
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently use the recommended values from BSpec, but the VBT
specifies the correct value to use for the hardware we have, so use
it. We also fall back to the recommended value in case we can't find
the VBT.
In addition, this code also provides some infrastructure to parse more
information about the DDI ports. There's a lot more information we
could extract and use in the future.
v2: - Move some code to init_vbt_defaults.
v3: - Rebase
- Clarify the "DVO Port" matching code
v4: - Use I915_MAX_PORTS
- Change the HAS_DDI checks
- Replace DRM_ERROR with DRM_DEBUG_KMS
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently treat the child_device_config as a simple struct, but
this is not correct: new BDB versions change the meaning of some
offsets, so the struct needs to be adjusted for each version.
Since there are too many changes (today we're in version 170!), making
a big versioned union would be too complicated, so child_device_config
is now a union of 3 things: (i) a "raw" byte array that's safe to use
anywhere; (ii) an "old" structure that's the one we've been using and
should be safe to keep in the SDVO and TV code; and (iii) a "common"
structure that should contain only fields that are common for all the
known VBT versions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Initial parsing of the VBT MIPI block. For now, just store the panel id
if found.
Note: Again there seems to be no documentation for this piece of lore.
The doc situation for byt+ is just a bad joke :(
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the VBT to see if the machine has inverted FDI RX polarity on
CPT. Based on this bit, set the appropriate bit on the TRANS_CHICKEN2
registers.
This should fix some machines that were showing black screens on all
outputs.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60029
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
These are unintuitive. These are type bool and return -1 casted to true
on failure. Let's just make it return an int. The callers don't care,
but let's change this as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Support for parsing parameters for S3D support and T3 optimization
support is implemented. The order for the bdb_edp struct was also
made similar to that indicated in spec.
Signed-off-by: Rohit Jain <rohit.jain@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Vijay A. Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
I have no evidence for this byte being used this way, and lots of
counterexamples. Restore the struct to its empirical definition and
patch up gmbus setup to match.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Store the panel power sequencing delays in the dp private structure,
rather than the global device structure. Who knows, maybe we'll get
more than one eDP device in the future.
From the eDP spec, we need the following numbers:
T1 + T3 Power on to Aux Channel operation (panel_power_up_delay)
This marks how long it takes the panel to boot up and
get ready to receive aux channel communications.
T8 Video signal to backlight on (backlight_on_delay)
Once a valid video signal is being sent to the device,
it can take a while before the panel is actuall
showing useful data. This delay allows the panel
to get something reasonable up before the backlight
is turned on.
T9 Backlight off to video off (backlight_off_delay)
Turning the backlight off can take a moment, so
this delay makes sure there is still valid video
data on the screen.
T10 Video off to power off (panel_power_down_delay)
Presumably this delay allows the panel to perform
an orderly shutdown of the display.
T11 + T12 Power off to power on (panel_power_cycle_delay)
So, once you turn the panel off, you have to wait a
while before you can turn it back on. This delay is
usually the longest in the entire sequence.
Neither the VBIOS source code nor the hardware documentation has a
clear mapping between the delay values they provide and those required
by the eDP spec. The VBIOS code actually uses two different labels for
the delay values in the five words of the relevant VBT table.
**** MORE LATER ***
Look at both the current hardware register settings and the VBT
specified panel power sequencing timings. Use the maximum of the two
delays, to make sure things work reliably. If there is no VBT data,
then those values will be initialized to zero, so we'll just use the
values as programmed in the hardware. Note that the BIOS just fetches
delays from the VBT table to place in the hardware registers, so we
should get the same values from both places, except for rounding.
VBT doesn't provide any values for T1 or T2, so we'll always just use
the hardware value for that.
The panel power up delay is thus T1 + T2 + T3, which should be
sufficient in all cases.
The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy
for T11, which isn't available anywhere.
For the backlight delays, the eDP spec says T6 + T8 is the delay from the
end of link training to backlight on and T9 is the delay from
backlight off until video off. The hardware provides a 'backlight on'
delay, which I'm taking to be T6 + T8 while the VBT provides something
called 'T7', which I'm assuming is s
On the macbook air I'm testing with, this yields a power-up delay of
over 200ms and a power-down delay of over 600ms. It all works now, but
we're frobbing these power controls several times during mode setting,
making the whole process take an awfully long time.
Signed-off-by: Keith Packard <keithp@keithp.com>
This includes whether an eDP panel is present, and whether that should
use SSC (and at what frequency)
Signed-off-by: Keith Packard <keithp@keithp.com>
This tells the driver whether a CK505 clock source is available on
pre-PCH hardware. If so, it should be used as the non-SSC source,
leaving the internal clock for use as the SSC source.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wison <chris@chris-wilson.co.uk>
