Remove unnecessary delay during the TX ring configuration.
This will cause delay, especially during link down and
link up activity.
Furthermore, old SKUs like as I225 will call the reset_adapter
to reset the controller during TSN mode Gate Control List (GCL)
setting. This will add more time to the configuration of the
real-time use case.
It doesn't mentioned about this delay in the Software User Manual.
It might have been ported from legacy code I210 in the past.
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add condition to increase the qbv counter during taprio qbv
configuration only.
There might be a case when TC already been setup then user configure
the ETF/CBS qdisc and this counter will increase if no condition above.
Fixes: ae4fe46983 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Before requesting a packet transmission to be hardware timestamped,
check if the user has TX timestamping enabled. Fixes an issue that if
a packet was internally forwarded to the NIC, and it had the
SKBTX_HW_TSTAMP flag set, the driver would mark that timestamp as
skipped.
In reality, that timestamp was "not for us", as TX timestamp could
never be enabled in the NIC.
Checking if the TX timestamping is enabled earlier has a secondary
effect that when TX timestamping is disabled, there's no need to check
for timestamp timeouts.
We should only take care to free any pending timestamp when TX
timestamping is disabled, as that skb would never be released
otherwise.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the igc driver supports timestamping only one tx packet at a
time. During the transmission flow, the skb that requires hardware
timestamping is saved in adapter->ptp_tx_skb. Once hardware has the
timestamp, an interrupt is delivered, and adapter->ptp_tx_work is
scheduled. In igc_ptp_tx_work(), we read the timestamp register, update
adapter->ptp_tx_skb, and notify the network stack.
While the thread executing the transmission flow (the user process
running in kernel mode) and the thread executing ptp_tx_work don't
access adapter->ptp_tx_skb concurrently, there are two other places
where adapter->ptp_tx_skb is accessed: igc_ptp_tx_hang() and
igc_ptp_suspend().
igc_ptp_tx_hang() is executed by the adapter->watchdog_task worker
thread which runs periodically so it is possible we have two threads
accessing ptp_tx_skb at the same time. Consider the following scenario:
right after __IGC_PTP_TX_IN_PROGRESS is set in igc_xmit_frame_ring(),
igc_ptp_tx_hang() is executed. Since adapter->ptp_tx_start hasn't been
written yet, this is considered a timeout and adapter->ptp_tx_skb is
cleaned up.
This patch fixes the issue described above by adding the ptp_tx_lock to
protect access to ptp_tx_skb and ptp_tx_start fields from igc_adapter.
Since igc_xmit_frame_ring() called in atomic context by the networking
stack, ptp_tx_lock is defined as a spinlock, and the irq safe variants
of lock/unlock are used.
With the introduction of the ptp_tx_lock, the __IGC_PTP_TX_IN_PROGRESS
flag doesn't provide much of a use anymore so this patch gets rid of it.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Guarantee that when probe() is run again, PTM and PCI busmaster will be
in the same state as it was if the driver was never loaded.
Avoid an i225/i226 hardware issue that PTM requests can be made even
though PCI bus mastering is not enabled. These unexpected PTM requests
can crash some systems.
So, "force" disable PTM and busmastering before removing the driver,
so they can be re-enabled in the right order during probe(). This is
more like a workaround and should be applicable for i225 and i226, in
any platform.
Fixes: 1b5d73fb86 ("igc: Enable PCIe PTM")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
High XDP load triggers the netdev watchdog:
|NETDEV WATCHDOG: enp3s0 (igc): transmit queue 2 timed out
The reason is the Tx queue transmission start (txq->trans_start) is not updated
in XDP code path. Therefore, add it for all XDP transmission functions.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZGKqEAAKCRDbK58LschI
g6LYAQDp1jAszCOkmJ8VUA0ZyC5NAFDv+7y9Nd1toYWYX1btzAEAkf8+5qBJ1qmI
P5M0hjMTbH4MID9Aql10ZbMHheyOBAo=
=NUQM
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-05-16
We've added 57 non-merge commits during the last 19 day(s) which contain
a total of 63 files changed, 3293 insertions(+), 690 deletions(-).
The main changes are:
1) Add precision propagation to verifier for subprogs and callbacks,
from Andrii Nakryiko.
2) Improve BPF's {g,s}setsockopt() handling with wrong option lengths,
from Stanislav Fomichev.
3) Utilize pahole v1.25 for the kernel's BTF generation to filter out
inconsistent function prototypes, from Alan Maguire.
4) Various dyn-pointer verifier improvements to relax restrictions,
from Daniel Rosenberg.
5) Add a new bpf_task_under_cgroup() kfunc for designated task,
from Feng Zhou.
6) Unblock tests for arm64 BPF CI after ftrace supporting direct call,
from Florent Revest.
7) Add XDP hint kfunc metadata for RX hash/timestamp for igc,
from Jesper Dangaard Brouer.
8) Add several new dyn-pointer kfuncs to ease their usability,
from Joanne Koong.
9) Add in-depth LRU internals description and dot function graph,
from Joe Stringer.
10) Fix KCSAN report on bpf_lru_list when accessing node->ref,
from Martin KaFai Lau.
11) Only dump unprivileged_bpf_disabled log warning upon write,
from Kui-Feng Lee.
12) Extend test_progs to directly passing allow/denylist file,
from Stephen Veiss.
13) Fix BPF trampoline memleak upon failure attaching to fentry,
from Yafang Shao.
14) Fix emitting struct bpf_tcp_sock type in vmlinux BTF,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (57 commits)
bpf: Fix memleak due to fentry attach failure
bpf: Remove bpf trampoline selector
bpf, arm64: Support struct arguments in the BPF trampoline
bpftool: JIT limited misreported as negative value on aarch64
bpf: fix calculation of subseq_idx during precision backtracking
bpf: Remove anonymous union in bpf_kfunc_call_arg_meta
bpf: Document EFAULT changes for sockopt
selftests/bpf: Correctly handle optlen > 4096
selftests/bpf: Update EFAULT {g,s}etsockopt selftests
bpf: Don't EFAULT for {g,s}setsockopt with wrong optlen
libbpf: fix offsetof() and container_of() to work with CO-RE
bpf: Address KCSAN report on bpf_lru_list
bpf: Add --skip_encoding_btf_inconsistent_proto, --btf_gen_optimized to pahole flags for v1.25
selftests/bpf: Accept mem from dynptr in helper funcs
bpf: verifier: Accept dynptr mem as mem in helpers
selftests/bpf: Check overflow in optional buffer
selftests/bpf: Test allowing NULL buffer in dynptr slice
bpf: Allow NULL buffers in bpf_dynptr_slice(_rw)
selftests/bpf: Add testcase for bpf_task_under_cgroup
bpf: Add bpf_task_under_cgroup() kfunc
...
====================
Link: https://lore.kernel.org/r/20230515225603.27027-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Result after this patch:
found skb hwtstamp = 1677800973.642836757
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC hardware RX timestamping mechanism adds an optional tailored
header before the MAC header containing packet reception time. Optional
depending on RX descriptor TSIP status bit (IGC_RXDADV_STAT_TSIP). In
case this bit is set driver does offset adjustments to packet data start
and extracts the timestamp.
The timestamp need to be extracted before invoking the XDP bpf_prog,
because this area just before the packet is also accessible by XDP via
data_meta context pointer (and helper bpf_xdp_adjust_meta). Thus, an XDP
bpf_prog can potentially overwrite this and corrupt data that we want to
extract with the new kfunc for reading the timestamp.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182465791.616355.2583922957423587914.stgit@firesoul
This implements XDP hints kfunc for RX-hash (xmo_rx_hash).
The HW rss hash type is handled via mapping table.
This igc driver (default config) does L3 hashing for UDP packets
(excludes UDP src/dest ports in hash calc). Meaning RSS hash type is
L3 based. Tested that the igc_rss_type_num for UDP is either
IGC_RSS_TYPE_HASH_IPV4 or IGC_RSS_TYPE_HASH_IPV6.
This patch also updates AF_XDP zero-copy function igc_clean_rx_irq_zc()
to use the xdp_buff wrapper struct igc_xdp_buff.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182465285.616355.2701740913376314790.stgit@firesoul
Driver specific metadata data for XDP-hints kfuncs are propagated via tail
extending the struct xdp_buff with a locally scoped driver struct.
Zero-Copy AF_XDP/XSK does similar tricks via struct xdp_buff_xsk. This
xdp_buff_xsk struct contains a CB area (24 bytes) that can be used for
extending the locally scoped driver into. The XSK_CHECK_PRIV_TYPE define
catch size violations build time.
The changes needed for AF_XDP zero-copy in igc_clean_rx_irq_zc()
is done in next patch, because the member rx_desc isn't available
at this point.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182464779.616355.3761989884165609387.stgit@firesoul
When function igc_rx_hash() was introduced in v4.20 via commit 0507ef8a03
("igc: Add transmit and receive fastpath and interrupt handlers"), the
hardware wasn't configured to provide RSS hash, thus it made sense to not
enable net_device NETIF_F_RXHASH feature bit.
The NIC hardware was configured to enable RSS hash info in v5.2 via commit
2121c2712f ("igc: Add multiple receive queues control supporting"), but
forgot to set the NETIF_F_RXHASH feature bit.
The original implementation of igc_rx_hash() didn't extract the associated
pkt_hash_type, but statically set PKT_HASH_TYPE_L3. The largest portions of
this patch are about extracting the RSS Type from the hardware and mapping
this to enum pkt_hash_types. This was based on Foxville i225 software user
manual rev-1.3.1 and tested on Intel Ethernet Controller I225-LM (rev 03).
For UDP it's worth noting that RSS (type) hashing have been disabled both for
IPv4 and IPv6 (see IGC_MRQC_RSS_FIELD_IPV4_UDP + IGC_MRQC_RSS_FIELD_IPV6_UDP)
because hardware RSS doesn't handle fragmented pkts well when enabled (can
cause out-of-order). This results in PKT_HASH_TYPE_L3 for UDP packets, and
hash value doesn't include UDP port numbers. Not being PKT_HASH_TYPE_L4, have
the effect that netstack will do a software based hash calc calling into
flow_dissect, but only when code calls skb_get_hash(), which doesn't
necessary happen for local delivery.
For QA verification testing I wrote a small bpftrace prog:
[0] https://github.com/xdp-project/xdp-project/blob/master/areas/hints/monitor_skb_hash_on_dev.bt
Fixes: 2121c2712f ("igc: Add multiple receive queues control supporting")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/bpf/168182464270.616355.11391652654430626584.stgit@firesoul
The check introduced in the commit a5fd39464a ("igc: Lift TAPRIO schedule
restriction") can detect a false positive error in some corner case.
For instance,
tc qdisc replace ... taprio num_tc 4
...
sched-entry S 0x01 100000 # slot#1
sched-entry S 0x03 100000 # slot#2
sched-entry S 0x04 100000 # slot#3
sched-entry S 0x08 200000 # slot#4
flags 0x02 # hardware offload
Here the queue#0 (the first queue) is on at the slot#1 and #2,
and off at the slot#3 and #4. Under the current logic, when the slot#4
is examined, validate_schedule() returns *false* since the enablement
count for the queue#0 is two and it is already off at the previous slot
(i.e. #3). But this definition is truely correct.
Let's fix the logic to enforce a strict validation for consecutively-opened
slots.
Fixes: a5fd39464a ("igc: Lift TAPRIO schedule restriction")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-07 (igc)
This series contains updates to igc driver only.
Muhammad adds tracking and reporting of QBV config errors.
Tan Tee adds support for configuring max SDU for each Tx queue.
Sasha removes check for alternate media as only one media type is
supported.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Clean up and optimize watchdog task
igc: offload queue max SDU from tc-taprio
igc: Add qbv_config_change_errors counter
====================
Link: https://lore.kernel.org/r/20230307221332.3997881-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i225/i226 parts used only one media type copper. The copper media type is
not replaceable. Clean up the code accordingly, and remove the obsolete
media replacement and reset options.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for configuring the max SDU for each Tx queue.
If not specified, keep the default.
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add ConfigChangeError(qbv_config_change_errors) when user try to set the
AdminBaseTime to past value while the current GCL is still running.
The ConfigChangeError counter should not be increased when a gate control
list is scheduled into the future.
User can use "ethtool -S <interface> | grep qbv_config_change_errors"
command to check the counter values.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
netserver -p 16604
netperf -H 192.168.0.2 -l 600 -p 16604 -t UDP_STREAM -- -m 64000
Fixes: b27b8dc77b ("igc: Increase timeout value for Speed 100/1000/2500")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230206235818.662384-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are 2 classes of in-tree drivers currently:
- those who act upon struct tc_taprio_sched_entry :: gate_mask as if it
holds a bit mask of TXQs
- those who act upon the gate_mask as if it holds a bit mask of TCs
When it comes to the standard, IEEE 802.1Q-2018 does say this in the
second paragraph of section 8.6.8.4 Enhancements for scheduled traffic:
| A gate control list associated with each Port contains an ordered list
| of gate operations. Each gate operation changes the transmission gate
| state for the gate associated with each of the Port's traffic class
| queues and allows associated control operations to be scheduled.
In typically obtuse language, it refers to a "traffic class queue"
rather than a "traffic class" or a "queue". But careful reading of
802.1Q clarifies that "traffic class" and "queue" are in fact
synonymous (see 8.6.6 Queuing frames):
| A queue in this context is not necessarily a single FIFO data structure.
| A queue is a record of all frames of a given traffic class awaiting
| transmission on a given Bridge Port. The structure of this record is not
| specified.
i.o.w. their definition of "queue" isn't the Linux TX queue.
The gate_mask really is input into taprio via its UAPI as a mask of
traffic classes, but taprio_sched_to_offload() converts it into a TXQ
mask.
The breakdown of drivers which handle TC_SETUP_QDISC_TAPRIO is:
- hellcreek, felix, sja1105: these are DSA switches, it's not even very
clear what TXQs correspond to, other than purely software constructs.
Only the mqprio configuration with 8 TCs and 1 TXQ per TC makes sense.
So it's fine to convert these to a gate mask per TC.
- enetc: I have the hardware and can confirm that the gate mask is per
TC, and affects all TXQs (BD rings) configured for that priority.
- igc: in igc_save_qbv_schedule(), the gate_mask is clearly interpreted
to be per-TXQ.
- tsnep: Gerhard Engleder clarifies that even though this hardware
supports at most 1 TXQ per TC, the TXQ indices may be different from
the TC values themselves, and it is the TXQ indices that matter to
this hardware. So keep it per-TXQ as well.
- stmmac: I have a GMAC datasheet, and in the EST section it does
specify that the gate events are per TXQ rather than per TC.
- lan966x: again, this is a switch, and while not a DSA one, the way in
which it implements lan966x_mqprio_add() - by only allowing num_tc ==
NUM_PRIO_QUEUES (8) - makes it clear to me that TXQs are a purely
software construct here as well. They seem to map 1:1 with TCs.
- am65_cpsw: from looking at am65_cpsw_est_set_sched_cmds(), I get the
impression that the fetch_allow variable is treated like a prio_mask.
This definitely sounds closer to a per-TC gate mask rather than a
per-TXQ one, and TI documentation does seem to recomment an identity
mapping between TCs and TXQs. However, Roger Quadros would like to do
some testing before making changes, so I'm leaving this driver to
operate as it did before, for now. Link with more details at the end.
Based on this breakdown, we have 5 drivers with a gate mask per TC and
4 with a gate mask per TXQ. So let's make the gate mask per TXQ the
opt-in and the gate mask per TC the default.
Benefit from the TC_QUERY_CAPS feature that Jakub suggested we add, and
query the device driver before calling the proper ndo_setup_tc(), and
figure out if it expects one or the other format.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230202003621.2679603-15-vladimir.oltean@nxp.com/#25193204
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Siddharth Vadapalli <s-vadapalli@ti.com>
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
I225 have limitation when programming the BaseTime register which required
a power cycle of the controller. This limitation already lifted in I226.
This patch removes the restriction so that when user configure/remove any
TSN mode, it would not go into power cycle reset adapter.
How to test:
Schedule any gate control list configuration or delete it.
Example:
1)
BASE_TIME=$(date +%s%N)
tc qdisc replace dev $interface_name parent root handle 100 taprio \
num_tc 4 \
map 3 1 0 2 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time $BASE_TIME \
sched-entry S 0F 1000000 \
flags 0x2
2) tc qdisc del dev $intername_name root
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make reset task only executes for i225 and Qbv disabling to allow
i226 configure for 2nd GCL without resetting the adapter.
In i226, Tx won't hang if there is a GCL is already running, so in
this case we don't need to set FutScdDis bit.
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the Qbv BaseTime restriction for I226 so that the BaseTime can be
scheduled to the future time. A new register bit of Tx Qav Control
(Bit-7: FutScdDis) was introduced to allow I226 scheduling future time as
Qbv BaseTime and not having the Tx hang timeout issue.
Besides, according to datasheet section 7.5.2.9.3.3, FutScdDis bit has to
be configured first before the cycle time and base time.
Indeed the FutScdDis bit is only active on re-configuration, thus we have
to set the BASET_L to zero and then only set it to the desired value.
Please also note that the Qbv configuration flow is moved around based on
the Qbv programming guideline that is documented in the latest datasheet.
Co-developed-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The default setting of end_time minus start_time is whole 1 second.
Thus, if it's not being configured in any GCL entry then it will be
staying at original 1 second.
This patch is changing the start_time and end_time to be end_time as
if setting zero will be having weird HW behavior where the gate will
not be fully closed.
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Qbv users can specify a cycle time that is not equal to the total GCL
intervals. Hence, recalculation is necessary here to exclude the time
interval that exceeds the cycle time. As those GCL which exceeds the
cycle time will be truncated.
According to IEEE Std. 802.1Q-2018 section 8.6.9.2, once the end of
the list is reached, it will switch to the END_OF_CYCLE state and
leave the gates in the same state until the next cycle is started.
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce qbv_enable flag in igc_adapter struct to store the Qbv on/off.
So this allow the BaseTime to enroll with zero value.
Fixes: 61572d5f8f ("igc: Simplify TSN flags handling")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using the tc qdisc command, the user can set basetime to any value.
Checking should be done on the driver's side to prevent registering
basetime values that are less than zero.
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The I225 hardware has a limitation that packets can only be scheduled
in the [0, cycle-time] interval. So, scheduling a packet to the start
of the next cycle doesn't usually work.
To overcome this, we use the Transmit Descriptor first flag to indicates
that a packet should be the first packet (from a queue) in a cycle
according to the section 7.5.2.9.3.4 The First Packet on Each QBV Cycle
in Intel Discrete I225/6 User Manual.
But this only works if there was any packet from that queue during the
current cycle, to avoid this issue, we issue an empty packet if that's
not the case. Also require one more descriptor to be available, to take
into account the empty packet that might be issued.
Test Setup:
Talker: Use l2_tai to generate the launchtime into packet load.
Listener: Use timedump.c to compute the delta between packet arrival
and LaunchTime packet payload.
Test Result:
Before:
1666000610127300000,1666000610127300096,96,621273
1666000610127400000,1666000610127400192,192,621274
1666000610127500000,1666000610127500032,32,621275
1666000610127600000,1666000610127600128,128,621276
1666000610127700000,1666000610127700224,224,621277
1666000610127800000,1666000610127800064,64,621278
1666000610127900000,1666000610127900160,160,621279
1666000610128000000,1666000610128000000,0,621280
1666000610128100000,1666000610128100096,96,621281
1666000610128200000,1666000610128200192,192,621282
1666000610128300000,1666000610128300032,32,621283
1666000610128400000,1666000610128301056,-98944,621284
1666000610128500000,1666000610128302080,-197920,621285
1666000610128600000,1666000610128302848,-297152,621286
1666000610128700000,1666000610128303872,-396128,621287
1666000610128800000,1666000610128304896,-495104,621288
1666000610128900000,1666000610128305664,-594336,621289
1666000610129000000,1666000610128306688,-693312,621290
1666000610129100000,1666000610128307712,-792288,621291
1666000610129200000,1666000610128308480,-891520,621292
1666000610129300000,1666000610128309504,-990496,621293
1666000610129400000,1666000610128310528,-1089472,621294
1666000610129500000,1666000610128311296,-1188704,621295
1666000610129600000,1666000610128312320,-1287680,621296
1666000610129700000,1666000610128313344,-1386656,621297
1666000610129800000,1666000610128314112,-1485888,621298
1666000610129900000,1666000610128315136,-1584864,621299
1666000610130000000,1666000610128316160,-1683840,621300
1666000610130100000,1666000610128316928,-1783072,621301
1666000610130200000,1666000610128317952,-1882048,621302
1666000610130300000,1666000610128318976,-1981024,621303
1666000610130400000,1666000610128319744,-2080256,621304
1666000610130500000,1666000610128320768,-2179232,621305
1666000610130600000,1666000610128321792,-2278208,621306
1666000610130700000,1666000610128322816,-2377184,621307
1666000610130800000,1666000610128323584,-2476416,621308
1666000610130900000,1666000610128324608,-2575392,621309
1666000610131000000,1666000610128325632,-2674368,621310
1666000610131100000,1666000610128326400,-2773600,621311
1666000610131200000,1666000610128327424,-2872576,621312
1666000610131300000,1666000610128328448,-2971552,621313
1666000610131400000,1666000610128329216,-3070784,621314
1666000610131500000,1666000610131500032,32,621315
1666000610131600000,1666000610131600128,128,621316
1666000610131700000,1666000610131700224,224,621317
After:
1666073510646200000,1666073510646200064,64,2676462
1666073510646300000,1666073510646300160,160,2676463
1666073510646400000,1666073510646400256,256,2676464
1666073510646500000,1666073510646500096,96,2676465
1666073510646600000,1666073510646600192,192,2676466
1666073510646700000,1666073510646700032,32,2676467
1666073510646800000,1666073510646800128,128,2676468
1666073510646900000,1666073510646900224,224,2676469
1666073510647000000,1666073510647000064,64,2676470
1666073510647100000,1666073510647100160,160,2676471
1666073510647200000,1666073510647200256,256,2676472
1666073510647300000,1666073510647300096,96,2676473
1666073510647400000,1666073510647400192,192,2676474
1666073510647500000,1666073510647500032,32,2676475
1666073510647600000,1666073510647600128,128,2676476
1666073510647700000,1666073510647700224,224,2676477
1666073510647800000,1666073510647800064,64,2676478
1666073510647900000,1666073510647900160,160,2676479
1666073510648000000,1666073510648000000,0,2676480
1666073510648100000,1666073510648100096,96,2676481
1666073510648200000,1666073510648200192,192,2676482
1666073510648300000,1666073510648300032,32,2676483
1666073510648400000,1666073510648400128,128,2676484
1666073510648500000,1666073510648500224,224,2676485
1666073510648600000,1666073510648600064,64,2676486
1666073510648700000,1666073510648700160,160,2676487
1666073510648800000,1666073510648800000,0,2676488
1666073510648900000,1666073510648900096,96,2676489
1666073510649000000,1666073510649000192,192,2676490
1666073510649100000,1666073510649100032,32,2676491
1666073510649200000,1666073510649200128,128,2676492
1666073510649300000,1666073510649300224,224,2676493
1666073510649400000,1666073510649400064,64,2676494
1666073510649500000,1666073510649500160,160,2676495
1666073510649600000,1666073510649600000,0,2676496
1666073510649700000,1666073510649700096,96,2676497
1666073510649800000,1666073510649800192,192,2676498
1666073510649900000,1666073510649900032,32,2676499
1666073510650000000,1666073510650000128,128,2676500
Fixes: 82faa9b799 ("igc: Add support for ETF offloading")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Co-developed-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Co-developed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Malli C <mallikarjuna.chilakala@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The launchtime offset should be corrected according to sections 7.5.2.6
Transmit Scheduling Latency of the Intel Ethernet I225/I226 Software
User Manual.
Software can compensate the latency between the transmission scheduling
and the time that packet is transmitted to the network by setting this
GTxOffset register. Without setting this register, there may be a
significant delay between the packet scheduling and the network point.
This patch helps to reduce the latency for each of the link speed.
Before:
10Mbps : 11000 - 13800 nanosecond
100Mbps : 1300 - 1700 nanosecond
1000Mbps : 190 - 600 nanosecond
2500Mbps : 1400 - 1700 nanosecond
After:
10Mbps : less than 750 nanosecond
100Mbps : less than 192 nanosecond
1000Mbps : less than 128 nanosecond
2500Mbps : less than 128 nanosecond
Test Setup:
Talker : Use l2_tai.c to generate the launchtime into packet payload.
Listener: Use timedump.c to compute the delta between packet arrival and
LaunchTime packet payload.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the capability to map non-linear xdp frames in XDP_TX and
ndo_xdp_xmit callback.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220817173628.109102-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The initially merged version of the igc driver code (via commit
146740f9ab, "igc: Add support for PF") contained the following
IGC_REMOVED checks in the igc_rd32/wr32() MMIO accessors:
u32 igc_rd32(struct igc_hw *hw, u32 reg)
{
u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr);
u32 value = 0;
if (IGC_REMOVED(hw_addr))
return ~value;
value = readl(&hw_addr[reg]);
/* reads should not return all F's */
if (!(~value) && (!reg || !(~readl(hw_addr))))
hw->hw_addr = NULL;
return value;
}
And:
#define wr32(reg, val) \
do { \
u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \
if (!IGC_REMOVED(hw_addr)) \
writel((val), &hw_addr[(reg)]); \
} while (0)
E.g. igb has similar checks in its MMIO accessors, and has a similar
macro E1000_REMOVED, which is implemented as follows:
#define E1000_REMOVED(h) unlikely(!(h))
These checks serve to detect and take note of an 0xffffffff MMIO read
return from the device, which can be caused by a PCIe link flap or some
other kind of PCI bus error, and to avoid performing MMIO reads and
writes from that point onwards.
However, the IGC_REMOVED macro was not originally implemented:
#ifndef IGC_REMOVED
#define IGC_REMOVED(a) (0)
#endif /* IGC_REMOVED */
This led to the IGC_REMOVED logic to be removed entirely in a
subsequent commit (commit 3c215fb18e, "igc: remove IGC_REMOVED
function"), with the rationale that such checks matter only for
virtualization and that igc does not support virtualization -- but a
PCIe device can become detached even without virtualization being in
use, and without proper checks, a PCIe bus error affecting an igc
adapter will lead to various NULL pointer dereferences, as the first
access after the error will set hw->hw_addr to NULL, and subsequent
accesses will blindly dereference this now-NULL pointer.
This patch reinstates the IGC_REMOVED checks in igc_rd32/wr32(), and
implements IGC_REMOVED the way it is done for igb, by checking for the
unlikely() case of hw_addr being NULL. This change prevents the oopses
seen when a PCIe link flap occurs on an igc adapter.
Fixes: 146740f9ab ("igc: Add support for PF")
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
igc_set_spd_dplx method is not used. This patch comes to tidy up
the driver code.
Reported-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, igc_construct_skb_zc() currently allocates and reserves
additional `xdp->data_meta - xdp->data_hard_start`, which is about
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only (+ meta) to
__napi_alloc_skb() and don't reserve anything. This will give
enough headroom for stack processing.
Also, net_prefetch() xdp->data_meta and align the copy size to
speed-up memcpy() a little and better match igc_construct_skb().
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Muhammad Husaini Zulkifli