[ Upstream commit 853a603030 ]
RZ/G2L interrupt chips require that the interrupt is masked before changing
the NMI, IRQ, TINT interrupt settings. Aside of that, after setting an edge
trigger type it is required to clear the interrupt status register in order
to avoid spurious interrupts.
The current implementation fails to do either of that and therefore is
prone to generate spurious interrupts when setting the trigger type.
Address this by:
- Ensuring that the interrupt is masked at the chip level across the
update for the TINT chip
- Clearing the interrupt status register after updating the trigger mode
for edge type interrupts
[ tglx: Massaged changelog and reverted the spin_lock_irqsave() change as
the set_type() callback is always called with interrupts disabled. ]
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eca4731cc ]
There are 2 TITSR registers available on the IA55 interrupt controller.
Add a macro that retrieves the TITSR register offset based on it's
index. This macro is useful in when adding suspend/resume support so both
TITSR registers can be accessed in a for loop.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20231120111820.87398-7-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 853a603030 ("irqchip/renesas-rzg2l: Prevent spurious interrupts when setting trigger type")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eec61df55 ]
The irq_eoi() callback of the RZ/G2L interrupt chip clears the relevant
interrupt cause bit in the TSCR register by writing to it.
This write is not sufficient because the write is posted and therefore not
guaranteed to immediately clear the bit. Due to that delay the CPU can
raise the just handled interrupt again.
Prevent this by reading the register back which causes the posted write to
be flushed to the hardware before the read completes.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef88eefb1a ]
The RZ/G2L manual (chapter "IRQ Status Control Register (ISCR)") describes
the operation to clear interrupts through the ISCR register as follows:
[Write operation]
When "Falling-edge detection", "Rising-edge detection" or
"Falling/Rising-edge detection" is set in IITSR:
- In case ISTAT is 1
0: IRQn interrupt detection status is cleared.
1: Invalid to write.
- In case ISTAT is 0
Invalid to write.
When "Low-level detection" is set in IITSR.:
Invalid to write.
Take the interrupt type into account when clearing interrupts through the
ISCR register to avoid writing the ISCR when the interrupt type is level.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231120111820.87398-6-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 9eec61df55 ("irqchip/renesas-rzg2l: Flush posted write in irq_eoi()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9c92006b89 upstream.
RISC-V PLIC cannot "end-of-interrupt" (EOI) disabled interrupts, as
explained in the description of Interrupt Completion in the PLIC spec:
"The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the claim/complete
register. The PLIC does not check whether the completion ID is the same
as the last claim ID for that target. If the completion ID does not match
an interrupt source that *is currently enabled* for the target, the
completion is silently ignored."
Commit 69ea463021 ("irqchip/sifive-plic: Fixup EOI failed when masked")
ensured that EOI is successful by enabling interrupt first, before EOI.
Commit a1706a1c50 ("irqchip/sifive-plic: Separate the enable and mask
operations") removed the interrupt enabling code from the previous
commit, because it assumes that interrupt should already be enabled at the
point of EOI.
However, this is incorrect: there is a window after a hart claiming an
interrupt and before irq_desc->lock getting acquired, interrupt can be
disabled during this window. Thus, EOI can be invoked while the interrupt
is disabled, effectively nullify this EOI. This results in the interrupt
never gets asserted again, and the device who uses this interrupt appears
frozen.
Make sure that interrupt is really enabled before EOI.
Fixes: a1706a1c50 ("irqchip/sifive-plic: Separate the enable and mask operations")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: linux-riscv@lists.infradead.org
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240131081933.144512-1-namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec4308ecfc upstream.
The GIC/ITS code is designed to ensure to pick up any preallocated LPI
tables on the redistributors, as enabling LPIs is a one-way switch. There
is no such restriction for vLPIs, and for GICv4.1 it is expected to
allocate a new vPE table at boot.
This works as intended when initializing an ITS, however when setting up a
redistributor in cpu_init_lpis() the early return for preallocated RD
tables skips straight past the GICv4 setup. This all comes to a head when
trying to kexec() into a new kernel, as the new kernel silently fails to
set up GICv4, leading to a complete loss of SGIs and LPIs for KVM VMs.
Slap a band-aid on the problem by ensuring its_cpu_init_lpis() always
initializes GICv4 on the way out, even if the other RD tables were
preallocated.
Fixes: 6479450f72 ("irqchip/gic-v4: Fix occasional VLPI drop")
Reported-by: George Cherian <gcherian@marvell.com>
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240219185809.286724-2-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af9acbfc2c upstream.
When updating the affinity of a VPE, the VMOVP command is currently skipped
if the two CPUs are part of the same VPE affinity.
But this is wrong, as the doorbell corresponding to this VPE is still
delivered on the 'old' CPU, which screws up the balancing. Furthermore,
offlining that 'old' CPU results in doorbell interrupts generated for this
VPE being discarded.
The harsh reality is that VMOVP cannot be elided when a set_affinity()
request occurs. It needs to be obeyed, and if an optimisation is to be
made, it is at the point where the affinity change request is made (such as
in KVM).
Drop the VMOVP elision altogether, and only use the vpe_table_mask
to try and stay within the same ITS affinity group if at all possible.
Fixes: dd3f050a21 (irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP)
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240213101206.2137483-4-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0344d6854 upstream.
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1c2765c6a ]
eiointc_domain_alloc() uses struct eiointc, which is not defined, for a
pointer. Older compilers treat that as a forward declaration and due to
assignment of a void pointer there is no warning emitted. As the variable
is then handed in as a void pointer argument to irq_domain_set_info() the
code is functional.
Use struct eiointc_priv instead.
[ tglx: Rewrote changelog ]
Fixes: dd281e1a1a ("irqchip: Add Loongson Extended I/O interrupt controller support")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20240130082722.2912576-2-maobibo@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8554cba1d6 ]
The STM32F4/7 EXTI driver was missing the xlate callback, so IRQ trigger
flags specified in the device tree were being ignored. This was
preventing the RTC alarm interrupt from working, because it must be set
to trigger on the rising edge to function correctly.
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20231003162003.1649967-1-ben.wolsieffer@hefring.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e13cd66bd8 ]
The RISC-V INTC local interrupts are per-HART (or per-CPU) so we
create INTC IRQ domain only for the INTC node belonging to the boot
HART. This means only the boot HART INTC node will be marked as
initialized and other INTC nodes won't be marked which results
downstream interrupt controllers (such as PLIC, IMSIC and APLIC
direct-mode) not being probed due to missing device suppliers.
To address this issue, we mark all INTC node for which we don't
create IRQ domain as initialized.
Reported-by: Dmitry Dunaev <dunaev@tecon.ru>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230926102801.1591126-1-dunaev@tecon.ru
Link: https://lore.kernel.org/r/20231003044403.1974628-4-apatel@ventanamicro.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b8df572ba upstream.
The logic to clear the TINT interrupt source in rzg2l_irqc_irq_disable()
is wrong as the mask is correct only for LSB on the TSSR register.
This issue is found when testing with two TINT interrupt sources. So fix
the logic for all TINTs by using the macro TSSEL_SHIFT() to multiply
tssr_offset with 8.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230918122411.237635-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e99b73afd ]
Return value of function eiointc_index is int, however it is converted
into uint32_t and then compared smaller than zero, this will cause logic
problem.
Fixes: dd281e1a1a ("irqchip: Add Loongson Extended I/O interrupt controller support")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230811095805.2974722-2-maobibo@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 926846a703 ]
We normally rely on the irq_to_cpuid_[un]lock() primitives to make
sure nothing will change col->idx while performing a LPI invalidation.
However, these primitives do not cover VPE doorbells, and we have
some open-coded locking for that. Unfortunately, this locking is
pretty bogus.
Instead, extend the above primitives to cover VPE doorbells and
convert the whole thing to it.
Fixes: f3a059219b ("irqchip/gic-v4.1: Ensure mutual exclusion between vPE affinity change and RD access")
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Cc: wanghaibin.wang@huawei.com
Tested-by: Kunkun Jiang <jiangkunkun@huawei.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20230617073242.3199746-1-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55ad248573 ]
The irq to block mapping is fixed, and interrupts from the first block
will always be routed to the first parent IRQ. But the parent interrupts
themselves can be routed to any available CPU.
This is used by the bootloader to map the first parent interrupt to the
boot CPU, regardless wether the boot CPU is the first one or the second
one.
When booting from the second CPU, the assumption that the first block's
IRQ is mapped to the first CPU breaks, and the system hangs because
interrupts do not get routed correctly.
Fix this by passing the appropriate bcm6434_l1_cpu to the interrupt
handler instead of the chip itself, so the handler always has the right
block.
Fixes: c7c42ec2ba ("irqchips/bmips: Add bcm6345-l1 interrupt controller")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230629072620.62527-1-jonas.gorski@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f679616565 upstream.
In an ACPI-based dual-bridge system, IRQ of each bridge's
PCH PIC sent to CPU is always a zero-based number, which
means that the IRQ on PCH PIC of each bridge is mapped into
vector range from 0 to 63 of upstream irqchip(e.g. EIOINTC).
EIOINTC N: [0 ... 63 | 64 ... 255]
-------- ----------
^ ^
| |
PCH PIC N |
PCH MSI N
For example, the IRQ vector number of sata controller on
PCH PIC of each bridge is 16, which is sent to upstream
irqchip of EIOINTC when an interrupt occurs, which will set
bit 16 of EIOINTC. Since hwirq of 16 on EIOINTC has been
mapped to a irq_desc for sata controller during hierarchy
irq allocation, the related mapped IRQ will be found through
irq_resolve_mapping() in the IRQ domain of EIOINTC.
So, the IRQ number set in HT vector register should be fixed
to be a zero-based number.
Cc: stable@vger.kernel.org
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Co-developed-by: liuyun <liuyun@loongson.cn>
Signed-off-by: liuyun <liuyun@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230614115936.5950-2-lvjianmin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 783422e704 upstream.
In DeviceTree path, when ht_vec_base is not zero, the hwirq of PCH PIC
will be assigned incorrectly. Because when pch_pic_domain_translate()
adds the ht_vec_base to hwirq, the hwirq does not have the ht_vec_base
subtracted when calling irq_domain_set_info().
The ht_vec_base is designed for the parent irq chip/domain of the PCH PIC.
It seems not proper to deal this in callbacks of the PCH PIC domain and
let's put this back like the initial commit ef8c01eb64 ("irqchip: Add
Loongson PCH PIC controller").
Fixes: bcdd75c596 ("irqchip/loongson-pch-pic: Add ACPI init support")
Cc: stable@vger.kernel.org
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Liu Peibao <liupeibao@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230614115936.5950-3-lvjianmin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4848229494 ]
The initialization function for the J-Core AIC aic_irq_of_init() is
currently missing the call to irq_alloc_descs() which allocates and
initializes all the IRQ descriptors. Add missing function call and
return the error code from irq_alloc_descs() in case the allocation
fails.
Fixes: 981b58f66c ("irqchip/jcore-aic: Add J-Core AIC driver")
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: Rob Landley <rob@landley.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230510163343.43090-1-glaubitz@physik.fu-berlin.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f31e4964 ]
While compiling with W=1, both gcc and clang complain about a
tricky way to initialize an array by filling it with a non-zero
value and then overrride some of the array elements.
In this case the override is intentional, so just disable the
specific warning for only this part of the code.
Note: the flag "-Woverride-init" is recognized by both compilers,
but the warning msg from clang reports "-Winitializer-overrides".
The doc of clang clarifies that the two flags are synonyms, so use
here only the flag name common on both compilers.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Fixes: c297493336 ("irqchip/stm32-exti: Simplify irq description table")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230601155614.34490-1-antonio.borneo@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91539341a3 ]
When checking for OF quirks, make sure either 'compatible' or 'property'
is set, and give up otherwise.
This avoids non-OF quirks being randomly applied as they don't have any
of the OF data that need checking.
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 44bd78dd2b ("irqchip/gic-v3: Disable pseudo NMIs on Mediatek devices w/ firmware issues")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14130211be ]
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/irqchip/irq-meson-gpio.c:153:34: error: ‘meson_irq_gpio_matches’ defined but not used [-Werror=unused-const-variable=]
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230512164506.212267-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44bd78dd2b ]
Some Chromebooks with Mediatek SoCs have a problem where the firmware
doesn't properly save/restore certain GICR registers. Newer
Chromebooks should fix this issue and we may be able to do firmware
updates for old Chromebooks. At the moment, the only known issue with
these Chromebooks is that we can't enable "pseudo NMIs" since the
priority register can be lost. Enabling "pseudo NMIs" on Chromebooks
with the problematic firmware causes crashes and freezes.
Let's detect devices with this problem and then disable "pseudo NMIs"
on them. We'll detect the problem by looking for the presence of the
"mediatek,broken-save-restore-fw" property in the GIC device tree
node. Any devices with fixed firmware will not have this property.
Our detection plan works because we never bake a Chromebook's device
tree into firmware. Instead, device trees are always bundled with the
kernel. We'll update the device trees of all affected Chromebooks and
then we'll never enable "pseudo NMI" on a kernel that is bundled with
old device trees. When a firmware update is shipped that fixes this
issue it will know to patch the device tree to remove the property.
In order to make this work, the quick detection mechanism of the GICv3
code is extended to be able to look for properties in addition to
looking at "compatible".
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230515131353.v2.2.I88dc0a0eb1d9d537de61604cd8994ecc55c0cac1@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3d6a0e4197 upstream.
Since we may hold gic_lock in hardirq context, use raw spinlock
makes more sense given that it is for low-level interrupt handling
routine and the critical section is small.
Fixes BUG:
[ 0.426106] =============================
[ 0.426257] [ BUG: Invalid wait context ]
[ 0.426422] 6.3.0-rc7-next-20230421-dirty #54 Not tainted
[ 0.426638] -----------------------------
[ 0.426766] swapper/0/1 is trying to lock:
[ 0.426954] ffffffff8104e7b8 (gic_lock){....}-{3:3}, at: gic_set_type+0x30/08
Fixes: 95150ae8b3 ("irqchip: mips-gic: Implement irq_set_type callback")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-3-jiaxun.yang@flygoat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c6c9c0495 upstream.
When a GIC local interrupt is not routable, it's vl_map will be used
to control some internal states for core (providing IPTI, IPPCI, IPFDC
input signal for core). Overriding it will interfere core's intetrupt
controller.
Do not touch vl_map if a local interrupt is not routable, we are not
going to remap it.
Before dd098a0e03 (" irqchip/mips-gic: Get rid of the reliance on
irq_cpu_online()"), if a local interrupt is not routable, then it won't
be requested from GIC Local domain, and thus gic_all_vpes_irq_cpu_online
won't be called for that particular interrupt.
Fixes: dd098a0e03 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-2-jiaxun.yang@flygoat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35727af2b1 ]
The T241 platform suffers from the T241-FABRIC-4 erratum which causes
unexpected behavior in the GIC when multiple transactions are received
simultaneously from different sources. This hardware issue impacts
NVIDIA server platforms that use more than two T241 chips
interconnected. Each chip has support for 320 {E}SPIs.
This issue occurs when multiple packets from different GICs are
incorrectly interleaved at the target chip. The erratum text below
specifies exactly what can cause multiple transfer packets susceptible
to interleaving and GIC state corruption. GIC state corruption can
lead to a range of problems, including kernel panics, and unexpected
behavior.
>From the erratum text:
"In some cases, inter-socket AXI4 Stream packets with multiple
transfers, may be interleaved by the fabric when presented to ARM
Generic Interrupt Controller. GIC expects all transfers of a packet
to be delivered without any interleaving.
The following GICv3 commands may result in multiple transfer packets
over inter-socket AXI4 Stream interface:
- Register reads from GICD_I* and GICD_N*
- Register writes to 64-bit GICD registers other than GICD_IROUTERn*
- ITS command MOVALL
Multiple commands in GICv4+ utilize multiple transfer packets,
including VMOVP, VMOVI, VMAPP, and 64-bit register accesses."
This issue impacts system configurations with more than 2 sockets,
that require multi-transfer packets to be sent over inter-socket
AXI4 Stream interface between GIC instances on different sockets.
GICv4 cannot be supported. GICv3 SW model can only be supported
with the workaround. Single and Dual socket configurations are not
impacted by this issue and support GICv3 and GICv4."
Link: https://developer.nvidia.com/docs/t241-fabric-4/nvidia-t241-fabric-4-errata.pdf
Writing to the chip alias region of the GICD_In{E} registers except
GICD_ICENABLERn has an equivalent effect as writing to the global
distributor. The SPI interrupt deactivate path is not impacted by
the erratum.
To fix this problem, implement a workaround that ensures read accesses
to the GICD_In{E} registers are directed to the chip that owns the
SPI, and disable GICv4.x features. To simplify code changes, the
gic_configure_irq() function uses the same alias region for both read
and write operations to GICD_ICFGR.
Co-developed-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com> (for SMCCC/SOC ID bits)
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230319024314.3540573-2-sdonthineni@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdd60211ee ]
When support suspend/resume for loongson-eiointc, the syscore_ops
is registered twice in dual-bridges machines where there are two
eiointc IRQ domains. Repeated registration of an same syscore_ops
broke syscore_ops_list. Also, cpuhp_setup_state_nocalls is only
needed to call for once. So the patch will corret them.
Fixes: a90335c2df ("irqchip/loongson-eiointc: Add suspend/resume support")
Cc: stable@vger.kernel.org
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230407083453.6305-4-lvjianmin@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64cc451e45 ]
In eiointc_acpi_init(), a *eiointc* node is passed into
acpi_get_vec_parent() instead of a required *NUMA* node (on some chip
like 3C5000L, a *NUMA* node means a *eiointc* node, but on some chip
like 3C5000, a *NUMA* node contains 4 *eiointc* nodes), and node in
struct acpi_vector_group is essentially a *NUMA* node, which will
lead to no parent matched for passed *eiointc* node. so the patch
adjusts code to use *NUMA* node for parameter node of
acpi_set_vec_parent/acpi_get_vec_parent.
Cc: stable@vger.kernel.org
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230407083453.6305-3-lvjianmin@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d12938dbc ]
1, Adjust the return of acpi_cascade_irqdomain_init() and check its
return value.
2, Combine unnecessary short lines to one long line.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221020142514.1725514-1-chenhuacai@loongson.cn
Stable-dep-of: 64cc451e45 ("irqchip/loongson-eiointc: Fix incorrect use of acpi_get_vec_parent")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 112eaa8fec upstream.
In pch_pic_parse_madt(), a NULL parent pointer will be
returned from acpi_get_vec_parent() for second pch-pic domain
related to second bridge while calling eiointc_acpi_init() at
first time, where the parent of it has not been initialized
yet, and will be initialized during second time calling
eiointc_acpi_init(). So, it's reasonable to return zero so
that failure of acpi_table_parse_madt() will be avoided, or else
acpi_cascade_irqdomain_init() will return and initialization of
followed pch_msi domain will be skipped.
Although it does not matter when pch_msi_parse_madt() returns
-EINVAL if no invalid parent is found, it's also reasonable to
return zero for that.
Cc: stable@vger.kernel.org
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230407083453.6305-2-lvjianmin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48ce2d722f upstream.
For dual-bridges scenario, pch_pic_acpi_init() will be called
in following path:
cpuintc_acpi_init
acpi_cascade_irqdomain_init(in cpuintc driver)
acpi_table_parse_madt
eiointc_parse_madt
eiointc_acpi_init /* this will be called two times
correspondingto parsing two
eiointc entries in MADT under
dual-bridges scenario*/
acpi_cascade_irqdomain_init(in eiointc driver)
acpi_table_parse_madt
pch_pic_parse_madt
pch_pic_acpi_init /* this will be called depend
on valid parent IRQ domain
handle for one or two times
corresponding to parsing
two pchpic entries in MADT
druring calling
eiointc_acpi_init() under
dual-bridges scenario*/
During the first eiointc_acpi_init() calling, the
pch_pic_acpi_init() will be called just one time since only
one valid parent IRQ domain handle will be found for current
eiointc IRQ domain.
During the second eiointc_acpi_init() calling, the
pch_pic_acpi_init() will be called two times since two valid
parent IRQ domain handles will be found. So in pch_pic_acpi_init(),
we must have a reasonable way to prevent from creating second same
pch_pic IRQ domain.
The patch matches gsi base information in created pch_pic IRQ
domains to check if the target domain has been created to avoid the
bug mentioned above.
Cc: stable@vger.kernel.org
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230407083453.6305-6-lvjianmin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13a157b38c ]
When support for the interrupt controller was added with a5042de268,
we forgot to update the flags to be set to contain IRQ_LEVEL. While the
flow handler is correct, the output from /proc/interrupts does not show
such interrupts as being level triggered when they are, correct that.
Fixes: a5042de268 ("irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221216230934.2478345-3-f.fainelli@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94debe03e8 ]
When support for the level triggered interrupt controller flavor was
added with c0ca726208, we forgot to update the flags to be set to
contain IRQ_LEVEL. While the flow handler is correct, the output from
/proc/interrupts does not show such interrupts as being level triggered
when they are, correct that.
Fixes: c0ca726208 ("irqchip/brcmstb-l2: Add support for the BCM7271 L2 controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221216230934.2478345-2-f.fainelli@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02298b7bae ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: cd844b0715 ("irqchip/ti-sci-intr: Add support for Interrupt Router driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102085611.3955984-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9419e70002 ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: a68a63cb4d ("irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102084208.3951758-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 071d068b89 ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: e6b78f2c3e ("irqchip: Add the Alpine MSIX interrupt controller")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102082811.3947760-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6caa5a2b78 ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: f8410e6265 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102121318.3990586-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a60a3cdcf ]
For cores less than 4, eg, loongson2k1000 with 2 cores, the
of_property_match_string() may return with an error value,
which causes that liointc could not work. At least isr0 is
what should be checked like previous commit b2c4c3969f
("irqchip/loongson-liointc: irqchip add 2.0 version") did.
Fixes: 0858ed035a ("irqchip/loongson-liointc: Add ACPI init support")
Signed-off-by: Liu Peibao <liupeibao@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104110712.23300-1-liupeibao@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4208d4faf3 ]
If of_iomap() failed, 'aic' should be freed before return. Otherwise
there is a memory leak.
Fixes: fead4dd496 ("irqchip: Add driver for WPCM450 interrupt controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221115092532.1704032-1-weiyongjun@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9ee20c85b ]
gic_probe() calls pm_runtime_get_sync() and added fail path as
rpm_put to put usage_counter. However, pm_runtime_get_sync()
will increment usage_counter even it failed. Fix it by replacing it with
pm_runtime_resume_and_get() to keep usage counter balanced.
Fixes: 9c8edddfc9 ("irqchip/gic: Add platform driver for non-root GICs that require RPM")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124065150.22809-1-shangxiaojing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c0013801 ]
In DT path of translate callback, if fwspec->param_count==1
and of_node is non-null, fwspec->param[1] will be accessed,
which is introduced from previous commit bcdd75c596
(irqchip/loongson-pch-pic: Add ACPI init support).
Before the patch, for non-null of_node, translate callback
(use irq_domain_translate_twocell()) will return -EINVAL if
fwspec->param_count < 2, so the check in the patch is added.
Fixes: bcdd75c596 ("irqchip/loongson-pch-pic: Add ACPI init support")
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221022075955.11726-3-lvjianmin@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3ae977d0e4 upstream.
parent is the interrupt parent, not the parent of node. Use
node->parent. This fixes endianness detection on big-endian platforms.
Fixes: 1b00adce8a ("irqchip/ls-extirq: Fix invalid wait context by avoiding to use regmap")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221201212807.616191-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Core code:
- Provide a generic wrapper which can be utilized in drivers to handle
the problem of force threaded demultiplex interrupts on RT enabled
kernels. This avoids conditionals and horrible quirks in drivers all
over the place.
- Fix up affected pinctrl and GPIO drivers to make them cleanly RT safe.
- Interrupt drivers:
- A new driver for the FSL MU platform specific MSI implementation.
- Make irqchip_init() available for pure ACPI based systems.
- Provide a functional DT binding for the Realtek RTL interrupt chip.
- The usual DT updates and small code improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=2ok5
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt updates from Thomas Gleixner:
"Core code:
- Provide a generic wrapper which can be utilized in drivers to
handle the problem of force threaded demultiplex interrupts on RT
enabled kernels. This avoids conditionals and horrible quirks in
drivers all over the place
- Fix up affected pinctrl and GPIO drivers to make them cleanly RT
safe
Interrupt drivers:
- A new driver for the FSL MU platform specific MSI implementation
- Make irqchip_init() available for pure ACPI based systems
- Provide a functional DT binding for the Realtek RTL interrupt chip
- The usual DT updates and small code improvements all over the
place"
* tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
irqchip: IMX_MU_MSI should depend on ARCH_MXC
irqchip/imx-mu-msi: Fix wrong register offset for 8ulp
irqchip/ls-extirq: Fix invalid wait context by avoiding to use regmap
dt-bindings: irqchip: Describe the IMX MU block as a MSI controller
irqchip: Add IMX MU MSI controller driver
dt-bindings: irqchip: renesas,irqc: Add r8a779g0 support
irqchip/gic-v3: Fix typo in comment
dt-bindings: interrupt-controller: ti,sci-intr: Fix missing reg property in the binding
dt-bindings: irqchip: ti,sci-inta: Fix warning for missing #interrupt-cells
irqchip: Allow extra fields to be passed to IRQCHIP_PLATFORM_DRIVER_END
platform-msi: Export symbol platform_msi_create_irq_domain()
irqchip/realtek-rtl: use parent interrupts
dt-bindings: interrupt-controller: realtek,rtl-intc: require parents
irqchip/realtek-rtl: use irq_domain_add_linear()
irqchip: Make irqchip_init() usable on pure ACPI systems
bcma: gpio: Use generic_handle_irq_safe()
gpio: mlxbf2: Use generic_handle_irq_safe()
platform/x86: intel_int0002_vgpio: Use generic_handle_irq_safe()
ssb: gpio: Use generic_handle_irq_safe()
pinctrl: amd: Use generic_handle_irq_safe()
...
The Freescale/NXP i.MX Messaging Unit is only present on Freescale/NXP
i.MX SoCs. Hence add a dependency on ARCH_MXC, to prevent asking the
user about this driver when configuring a kernel without Freescale/NXP
i.MX SoC family support.
While at it, expand "MU" to "Messaging Unit" in the help text.
Fixes: 70afdab904 ("irqchip: Add IMX MU MSI controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/7f3bd932614ddbff46a1b750ef45b231130364ad.1664900434.git.geert+renesas@glider.be
Including:
- Removal of the bus_set_iommu() interface which became
unnecesary because of IOMMU per-device probing
- Make the dma-iommu.h header private
- Intel VT-d changes from Lu Baolu:
- Decouple PASID and PRI from SVA
- Add ESRTPS & ESIRTPS capability check
- Cleanups
- Apple DART support for the M1 Pro/MAX SOCs
- Support for AMD IOMMUv2 page-tables for the DMA-API layer. The
v2 page-tables are compatible with the x86 CPU page-tables.
Using them for DMA-API prepares support for hardware-assisted
IOMMU virtualization
- Support for MT6795 Helio X10 M4Us in the Mediatek IOMMU driver
- Some smaller fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=h0sT
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- remove the bus_set_iommu() interface which became unnecesary because
of IOMMU per-device probing
- make the dma-iommu.h header private
- Intel VT-d changes from Lu Baolu:
- Decouple PASID and PRI from SVA
- Add ESRTPS & ESIRTPS capability check
- Cleanups
- Apple DART support for the M1 Pro/MAX SOCs
- support for AMD IOMMUv2 page-tables for the DMA-API layer.
The v2 page-tables are compatible with the x86 CPU page-tables. Using
them for DMA-API prepares support for hardware-assisted IOMMU
virtualization
- support for MT6795 Helio X10 M4Us in the Mediatek IOMMU driver
- some smaller fixes and cleanups
* tag 'iommu-updates-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (59 commits)
iommu/vt-d: Avoid unnecessary global DMA cache invalidation
iommu/vt-d: Avoid unnecessary global IRTE cache invalidation
iommu/vt-d: Rename cap_5lp_support to cap_fl5lp_support
iommu/vt-d: Remove pasid_set_eafe()
iommu/vt-d: Decouple PASID & PRI enabling from SVA
iommu/vt-d: Remove unnecessary SVA data accesses in page fault path
dt-bindings: iommu: arm,smmu-v3: Relax order of interrupt names
iommu: dart: Support t6000 variant
iommu/io-pgtable-dart: Add DART PTE support for t6000
iommu/io-pgtable: Add DART subpage protection support
iommu/io-pgtable: Move Apple DART support to its own file
iommu/mediatek: Add support for MT6795 Helio X10 M4Us
iommu/mediatek: Introduce new flag TF_PORT_TO_ADDR_MT8173
dt-bindings: mediatek: Add bindings for MT6795 M4U
iommu/iova: Fix module config properly
iommu/amd: Fix sparse warning
iommu/amd: Remove outdated comment
iommu/amd: Free domain ID after domain_flush_pages
iommu/amd: Free domain id in error path
iommu/virtio: Fix compile error with viommu_capable()
...
- arm64 perf: DDR PMU driver for Alibaba's T-Head Yitian 710 SoC, SVE
vector granule register added to the user regs together with SVE perf
extensions documentation.
- SVE updates: add HWCAP for SVE EBF16, update the SVE ABI documentation
to match the actual kernel behaviour (zeroing the registers on syscall
rather than "zeroed or preserved" previously).
- More conversions to automatic system registers generation.
- vDSO: use self-synchronising virtual counter access in gettimeofday()
if the architecture supports it.
- arm64 stacktrace cleanups and improvements.
- arm64 atomics improvements: always inline assembly, remove LL/SC
trampolines.
- Improve the reporting of EL1 exceptions: rework BTI and FPAC exception
handling, better EL1 undefs reporting.
- Cortex-A510 erratum 2658417: remove BF16 support due to incorrect
result.
- arm64 defconfig updates: build CoreSight as a module, enable options
necessary for docker, memory hotplug/hotremove, enable all PMUs
provided by Arm.
- arm64 ptrace() support for TPIDR2_EL0 (register provided with the SME
extensions).
- arm64 ftraces updates/fixes: fix module PLTs with mcount, remove
unused function.
- kselftest updates for arm64: simple HWCAP validation, FP stress test
improvements, validation of ZA regs in signal handlers, include larger
SVE and SME vector lengths in signal tests, various cleanups.
- arm64 alternatives (code patching) improvements to robustness and
consistency: replace cpucap static branches with equivalent
alternatives, associate callback alternatives with a cpucap.
- Miscellaneous updates: optimise kprobe performance of patching
single-step slots, simplify uaccess_mask_ptr(), move MTE registers
initialisation to C, support huge vmalloc() mappings, run softirqs on
the per-CPU IRQ stack, compat (arm32) misalignment fixups for
multiword accesses.
-----BEGIN PGP SIGNATURE-----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=jl3Z
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 perf: DDR PMU driver for Alibaba's T-Head Yitian 710 SoC, SVE
vector granule register added to the user regs together with SVE perf
extensions documentation.
- SVE updates: add HWCAP for SVE EBF16, update the SVE ABI
documentation to match the actual kernel behaviour (zeroing the
registers on syscall rather than "zeroed or preserved" previously).
- More conversions to automatic system registers generation.
- vDSO: use self-synchronising virtual counter access in gettimeofday()
if the architecture supports it.
- arm64 stacktrace cleanups and improvements.
- arm64 atomics improvements: always inline assembly, remove LL/SC
trampolines.
- Improve the reporting of EL1 exceptions: rework BTI and FPAC
exception handling, better EL1 undefs reporting.
- Cortex-A510 erratum 2658417: remove BF16 support due to incorrect
result.
- arm64 defconfig updates: build CoreSight as a module, enable options
necessary for docker, memory hotplug/hotremove, enable all PMUs
provided by Arm.
- arm64 ptrace() support for TPIDR2_EL0 (register provided with the SME
extensions).
- arm64 ftraces updates/fixes: fix module PLTs with mcount, remove
unused function.
- kselftest updates for arm64: simple HWCAP validation, FP stress test
improvements, validation of ZA regs in signal handlers, include
larger SVE and SME vector lengths in signal tests, various cleanups.
- arm64 alternatives (code patching) improvements to robustness and
consistency: replace cpucap static branches with equivalent
alternatives, associate callback alternatives with a cpucap.
- Miscellaneous updates: optimise kprobe performance of patching
single-step slots, simplify uaccess_mask_ptr(), move MTE registers
initialisation to C, support huge vmalloc() mappings, run softirqs on
the per-CPU IRQ stack, compat (arm32) misalignment fixups for
multiword accesses.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (126 commits)
arm64: alternatives: Use vdso/bits.h instead of linux/bits.h
arm64/kprobe: Optimize the performance of patching single-step slot
arm64: defconfig: Add Coresight as module
kselftest/arm64: Handle EINTR while reading data from children
kselftest/arm64: Flag fp-stress as exiting when we begin finishing up
kselftest/arm64: Don't repeat termination handler for fp-stress
ARM64: reloc_test: add __init/__exit annotations to module init/exit funcs
arm64/mm: fold check for KFENCE into can_set_direct_map()
arm64: ftrace: fix module PLTs with mcount
arm64: module: Remove unused plt_entry_is_initialized()
arm64: module: Make plt_equals_entry() static
arm64: fix the build with binutils 2.27
kselftest/arm64: Don't enable v8.5 for MTE selftest builds
arm64: uaccess: simplify uaccess_mask_ptr()
arm64: asm/perf_regs.h: Avoid C++-style comment in UAPI header
kselftest/arm64: Fix typo in hwcap check
arm64: mte: move register initialization to C
arm64: mm: handle ARM64_KERNEL_USES_PMD_MAPS in vmemmap_populate()
arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()
arm64/sve: Add Perf extensions documentation
...
Offset 0x124 should be for IMX_MU_TSR, not IMX_MU_GSR.
Fixes: 70afdab904 ("irqchip: Add IMX MU MSI controller driver")
Reported-by: Colin King <colin.i.king@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[maz: updated commit message, tags]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221004202414.216577-1-Frank.Li@nxp.com
The irqchip->irq_set_type method is called by __irq_set_trigger() under
the desc->lock raw spinlock.
The ls-extirq implementation, ls_extirq_irq_set_type(), uses an MMIO
regmap created by of_syscon_register(), which uses plain spinlocks
(the kind that are sleepable on RT).
Therefore, this is an invalid locking scheme for which we get a kernel
splat stating just that ("[ BUG: Invalid wait context ]"), because the
context in which the plain spinlock may sleep is atomic due to the raw
spinlock. We need to go raw spinlocks all the way.
Make this driver ioremap its INTPCR register on its own, and stop
relying on syscon to provide a regmap.
Fixes: 0dcd9f8727 ("irqchip: Add support for Layerscape external interrupt lines")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[maz: trimmed down commit log]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220728144254.175385-1-vladimir.oltean@nxp.com
* irq/misc-6.1:
: .
: Misc irqchip updates for 6.1:
:
: - Allow generic irqchip support without selecting CONFIG_OF_IRQ
:
: - Fix a couple of bindings for TI interrupts controllers
:
: - Yet another binding update for a Renesas SoC
:
: - The obligatory fixes from the spelling police
: .
dt-bindings: irqchip: renesas,irqc: Add r8a779g0 support
irqchip/gic-v3: Fix typo in comment
dt-bindings: interrupt-controller: ti,sci-intr: Fix missing reg property in the binding
dt-bindings: irqchip: ti,sci-inta: Fix warning for missing #interrupt-cells
irqchip: Make irqchip_init() usable on pure ACPI systems
Signed-off-by: Marc Zyngier <maz@kernel.org>
Biju Das