commit b0344d6854 upstream.
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94debe03e8 ]
When support for the level triggered interrupt controller flavor was
added with c0ca726208, we forgot to update the flags to be set to
contain IRQ_LEVEL. While the flow handler is correct, the output from
/proc/interrupts does not show such interrupts as being level triggered
when they are, correct that.
Fixes: c0ca726208 ("irqchip/brcmstb-l2: Add support for the BCM7271 L2 controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221216230934.2478345-2-f.fainelli@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Allow the user selection and building of this interrupt controller
driver as a module since it is used on ARM/ARM64 based systems as a
second level interrupt controller hanging off the ARM GIC and is
therefore loadable during boot.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-9-f.fainelli@gmail.com
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The UPG_AUX_AON_INTR2 Level 2 interrupt controller node is defined with
the "brcm,upg-aux-aon-l2-intc" compatible string in Device Tree and
behaves as an edge triggered standard Broadcom STB L2 interrupt
controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-7-f.fainelli@gmail.com
The HIF_SPI_INTR2 Level 2 interrupt controller node is defined with the
"brcm,hif-spi-l2-intc" compatible string in Device Tree and behaves as
an edge triggered standard Broadcom STB L2 interrupt controller.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-5-f.fainelli@gmail.com
Utilize the Broadcom interrupt controller standard property
"brcm,irq-can-wake" to flag whether this particular interrupt controller
instance is wake-up capable.
Since we do not know what type of parent interrupt controller we are
interfaced with, ensure that enable_irq_wake() is called early on.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200709223016.989-3-f.fainelli@gmail.com
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useful to print which interrupt controllers are registered in the
system and which parent IRQ they use, especially given that L2 interrupt
controllers do not call request_irq() on their parent interrupt and do
not appear under /proc/interrupts for that reason.
We used to print the base register address virtual address which had
little value, use %pOF to print the path to the Device Tree node which
maps to the physical address more easily and is what people need to
troubleshoot systems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix sparse warnings:
drivers/irqchip/irq-brcmstb-l2.c:278:12: warning:
symbol 'brcmstb_l2_edge_intc_of_init' was not declared. Should it be static?
drivers/irqchip/irq-brcmstb-l2.c:285:12: warning:
symbol 'brcmstb_l2_lvl_intc_of_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Using the irq_gc_lock/irq_gc_unlock functions in the suspend and
resume functions creates the opportunity for a deadlock during
suspend, resume, and shutdown. Using the irq_gc_lock_irqsave/
irq_gc_unlock_irqrestore variants prevents this possible deadlock.
Cc: stable@vger.kernel.org
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[maz: tidied up $SUBJECT]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful. so delete the prints.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the initialization of the generic irq chip for the BCM7271 L2
interrupt controller. This controller only supports level
interrupts and uses the "brcm,bcm7271-l2-intc" compatibility
string.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Added register block offsets to the brcmstb_l2_intc_data structure
for the status and mask registers to support reading the active
interupts in an abstracted way. It seems like an irq_chip method
should have been provided for this, but it's not there yet.
Abstracted the implementation of the handler, suspend, and resume
functions to not use any hard coded register offsets.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Saving the generic chip pointer in the brcmstb_l2_intc_data prevents
the need to call irq_get_domain_generic_chip(). Also don't need to
save parent_irq and base there since local variables in the
brcmstb_l2_intc_of_init() function are just as good.
The handle_edge_irq flow or chained_irq_enter takes care of the
acknowledgment of the interrupt so it is redundant to clear it in
brcmstb_l2_intc_irq_handle().
irq_linear_revmap() is a fast path equivalent of irq_find_mapping()
that is appropriate to use for domain controllers of this type.
Defining irq_mask_ack is slightly more efficient than just
implementing irq_mask and irq_ack separately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Broadcom STB platforms support S5 and we allow specific hardware
wake-up events to take us out of this state. Because we were not
defining an irq_pm_shutdown() function pointer, we would not be
correctly masking non-wakeup events, which would result in spurious
wake-ups from sources that were not explicitly configured for wake-up.
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The probe functions in this driver is not exported or declared
so make it static to fix the following warning:
drivers/irqchip/irq-brcmstb-l2.c:115:12: warning: symbol 'brcmstb_l2_intc_of_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lkml.kernel.org/r/1465408940-16414-1-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Pull irq core updates from Thomas Gleixner:
"This is the first (boring) part of irq updates:
- support for big endian I/O accessors in the generic irq chip
- cleanup of brcmstb/bcm7120 drivers so they can be reused for non
ARM SoCs
- the usual pile of fixes and updates for the various ARM irq chips"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip: dw-apb-ictl: Add PM support
irqchip: dw-apb-ictl: Enable IRQ_GC_MASK_CACHE_PER_TYPE
irqchip: dw-apb-ictl: Always use use {readl|writel}_relaxed
ARM: orion: convert the irq_reg_{readl,writel} calls to the new API
irqchip: atmel-aic: Add missing entry for rm9200 irq fixups
irqchip: atmel-aic: Rename at91sam9_aic_irq_fixup for naming consistency
irqchip: atmel-aic: Add specific irq fixup function for sam9g45 and sam9rl
irqchip: atmel-aic: Add irq fixups for at91sam926x SoCs
irqchip: atmel-aic: Add irq fixup for RTT block
irqchip: brcmstb-l2: Convert driver to use irq_reg_{readl,writel}
irqchip: bcm7120-l2: Convert driver to use irq_reg_{readl,writel}
irqchip: bcm7120-l2: Decouple driver from brcmstb-l2
irqchip: bcm7120-l2: Extend driver to support 64+ bit controllers
irqchip: bcm7120-l2: Use gc->mask_cache to simplify suspend/resume functions
irqchip: bcm7120-l2: Fix missing nibble in gc->unused mask
irqchip: bcm7120-l2: Make sure all register accesses use base+offset
irqchip: bcm7120-l2, brcmstb-l2: Remove ARM Kconfig dependency
irqchip: bcm7120-l2: Eliminate bad IRQ check
irqchip: brcmstb-l2: Eliminate dependency on ARM code
genirq: Generic chip: Add big endian I/O accessors
...
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Kevin Cernekee <cernekee@gmail.com>
Link: https://lkml.kernel.org/r/20141114221642.GA37468@dtor-ws
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This effectively converts the __raw_ accessors to the non-__raw_
equivalents. To handle BE, we pass IRQ_GC_BE_IO, similar to what was
done in irq-bcm7120-l2.c.
Since irq_reg_writel now takes an irq_chip_generic argument, writel must
be used for the initial hardware reset in the probe function. But that
operation never needs endian swapping, so it's probably not a big deal.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1415342669-30640-15-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The irq-brcmstb-l2 driver has a single dependency on the ARM code, the
do_bad_IRQ macro. Expand this macro in-place so that the driver can be
built on non-ARM platforms.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lkml.kernel.org/r/1415342669-30640-6-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The driver was configuring the interrupt handler for the Level-2
interrupts to be "level" triggered while they are in fact "edge"
triggered. Fix this by using the correct handler.
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lkml.kernel.org/r/1402337102-19428-1-git-send-email-f.fainelli@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds support for the Level-2 interrupt controller hardware
found in Broadcom Set Top Box System-on-a-Chip devices. This interrupt
controller is implemented using the generic IRQ chip driver with
separate enable and disable registers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Link: https://lkml.kernel.org/r/1400892054-24457-2-git-send-email-f.fainelli@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Doug Berger