[ Upstream commit b5ff74c1ef ]
For a physical PCI device that is passed through to a Hyper-V guest VM,
current code specifies the VMBus ring buffer size as 4 pages. But this
is an inappropriate dependency, since the amount of ring buffer space
needed is unrelated to PAGE_SIZE. For example, on x86 the ring buffer
size ends up as 16 Kbytes, while on ARM64 with 64 Kbyte pages, the ring
size bloats to 256 Kbytes. The ring buffer for PCI pass-thru devices
is used for only a few messages during device setup and removal, so any
space above a few Kbytes is wasted.
Fix this by declaring the ring buffer size to be a fixed 16 Kbytes.
Furthermore, use the VMBUS_RING_SIZE() macro so that the ring buffer
header is properly accounted for, and so the size is rounded up to a
page boundary, using the page size for which the kernel is built. While
w/64 Kbyte pages this results in a 64 Kbyte ring buffer header plus a
64 Kbyte ring buffer, that's the smallest possible with that page size.
It's still 128 Kbytes better than the current code.
Link: https://lore.kernel.org/linux-pci/20240216202240.251818-1-mhklinux@outlook.com
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilpo Jarvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72e34b8593 ]
The commit message in commit fc9a77040b ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf79e33cdd ]
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c93988221 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f70939871 ]
qcom_pcie_config_sid_sm8250() function no longer applies only to SM8250.
So let's rename it to reflect the actual IP version and also move its
definition to keep it sorted as per IP revisions.
Link: https://lore.kernel.org/r/20230316081117.14288-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Stable-dep-of: bf79e33cdd ("PCI: qcom: Enable BDF to SID translation properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 002bf2fbc0 ]
PM runtime can be done simultaneously with AER error handling. Avoid that
by using pm_runtime_get_sync() before and pm_runtime_put() after reset in
pcie_do_recovery() for all recovering devices.
pm_runtime_get_sync() will increase dev->power.usage_count counter to
prevent any possible future request to runtime suspend a device. It will
also resume a device, if it was previously in D3hot state.
I tested with igc device by doing simultaneous aer_inject and rpm
suspend/resume via /sys/bus/pci/devices/PCI_ID/power/control and can
reproduce:
igc 0000:02:00.0: not ready 65535ms after bus reset; giving up
pcieport 0000:00:1c.2: AER: Root Port link has been reset (-25)
pcieport 0000:00:1c.2: AER: subordinate device reset failed
pcieport 0000:00:1c.2: AER: device recovery failed
igc 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
The problem disappears when this patch is applied.
Link: https://lore.kernel.org/r/20240212120135.146068-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627c6db207 ]
Commit 5459c0b704 ("PCI/DPC: Quirk PIO log size for certain Intel Root
Ports") and commit 3b8803494a ("PCI/DPC: Quirk PIO log size for Intel Ice
Lake Root Ports") add quirks for Ice, Tiger and Alder Lake Root Ports.
System firmware for Raptor Lake still has the bug, so Linux logs the
warning below on several Raptor Lake systems like Dell Precision 3581 with
Intel Raptor Lake processor (0W18NX) system firmware/BIOS version 1.10.1.
pci 0000:00:07.0: [8086:a76e] type 01 class 0x060400
pci 0000:00:07.0: DPC: RP PIO log size 0 is invalid
pci 0000:00:07.1: [8086:a73f] type 01 class 0x060400
pci 0000:00:07.1: DPC: RP PIO log size 0 is invalid
Apply the quirk for Raptor Lake Root Ports as well.
This also enables the DPC driver to dump the RP PIO Log registers when DPC
is triggered.
Link: https://lore.kernel.org/r/20240305113057.56468-1-pmenzel@molgen.mpg.de
Reported-by: Niels van Aert <nvaert1986@hotmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218560
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Niels van Aert <nvaert1986@hotmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d5286d4e7 ]
A race condition between the .runtime_idle() callback and the .remove()
callback in the rtsx_pcr PCI driver leads to a kernel crash due to an
unhandled page fault [1].
The problem is that rtsx_pci_runtime_idle() is not expected to be running
after pm_runtime_get_sync() has been called, but the latter doesn't really
guarantee that. It only guarantees that the suspend and resume callbacks
will not be running when it returns.
However, if a .runtime_idle() callback is already running when
pm_runtime_get_sync() is called, the latter will notice that the runtime PM
status of the device is RPM_ACTIVE and it will return right away without
waiting for the former to complete. In fact, it cannot wait for
.runtime_idle() to complete because it may be called from that callback (it
arguably does not make much sense to do that, but it is not strictly
prohibited).
Thus in general, whoever is providing a .runtime_idle() callback needs
to protect it from running in parallel with whatever code runs after
pm_runtime_get_sync(). [Note that .runtime_idle() will not start after
pm_runtime_get_sync() has returned, but it may continue running then if it
has started earlier.]
One way to address that race condition is to call pm_runtime_barrier()
after pm_runtime_get_sync() (not before it, because a nonzero value of the
runtime PM usage counter is necessary to prevent runtime PM callbacks from
being invoked) to wait for the .runtime_idle() callback to complete should
it be running at that point. A suitable place for doing that is in
pci_device_remove() which calls pm_runtime_get_sync() before removing the
driver, so it may as well call pm_runtime_barrier() subsequently, which
will prevent the race in question from occurring, not just in the rtsx_pcr
driver, but in any PCI drivers providing .runtime_idle() callbacks.
Link: https://lore.kernel.org/lkml/20240229062201.49500-1-kai.heng.feng@canonical.com/ # [1]
Link: https://lore.kernel.org/r/5761426.DvuYhMxLoT@kreacher
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Ricky Wu <ricky_wu@realtek.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf67aefbe ]
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
This fixes PCI Parity Errors like :
3w-9xxx: scsi0: ERROR: (0x06:0x000C): PCI Parity Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000E): Controller Queue Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x0010): Microcontroller Error: clearing.
Link: https://lore.kernel.org/r/20240219132811.8351-1-joerg@wedekind.de
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=202425
Signed-off-by: Jörg Wedekind <joerg@wedekind.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aebfdfe39b ]
If device_register() fails in ntb_register_device(), the device name
allocated by dev_set_name() should be freed. As per the comment in
device_register(), callers should use put_device() to give up the
reference in the error path. So fix this by calling put_device() in the
error path so that the name can be freed in kobject_cleanup().
As a result of this, put_device() in the error path of
ntb_register_device() is removed and the actual error is returned.
Fixes: a1bd3baeb2 ("NTB: Add NTB hardware abstraction layer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20231201033057.1399131-1-yangyingliang@huaweicloud.com
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 956578e3d3 ]
As ntb_register_device() don't handle error of device_register(),
if ntb_register_device() returns error in pci_vntb_probe(), name of kobject
which is allocated in dev_set_name() called in device_add() is leaked.
As comment of device_add() says, it should call put_device() to drop the
reference count that was set in device_initialize()
when it fails, so the name can be freed in kobject_cleanup().
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Stable-dep-of: aebfdfe39b ("NTB: fix possible name leak in ntb_register_device()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dec529b0b0 ]
The commit in Fixes changed the logic on how resources are released and
introduced a new switchtec_exit_pci() that need to be called explicitly in
order to undo a corresponding switchtec_init_pci().
This was done in the remove function, but not in the probe.
Fix the probe now.
Fixes: df25461119 ("PCI: switchtec: Fix stdev_release() crash after surprise hot remove")
Link: https://lore.kernel.org/r/01446d2ccb91a578239915812f2b7dfbeb2882af.1703428183.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6568d82512 ]
The TLP Prefix Log Register consists of multiple DWORDs (PCIe r6.1 sec
7.9.14.13) but the loop in dpc_process_rp_pio_error() keeps reading from
the first DWORD, so we print only the first PIO TLP Prefix (duplicated
several times), and we never print the second, third, etc., Prefixes.
Add the iteration count based offset calculation into the config read.
Fixes: f20c4ea49e ("PCI/DPC: Add eDPC support")
Link: https://lore.kernel.org/r/20240118110815.3867-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: add user-visible details to commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39714fd73c ]
Make pci_dev_is_disconnected() public so that it can be called from
Intel VT-d driver to quickly fix/workaround the surprise removal
unplug hang issue for those ATS capable devices on PCIe switch downstream
hotplug capable ports.
Beside pci_device_is_present() function, this one has no config space
space access, so is light enough to optimize the normal pure surprise
removal and safe removal flow.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Tested-by: Haorong Ye <yehaorong@bytedance.com>
Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com>
Link: https://lore.kernel.org/r/20240301080727.3529832-2-haifeng.zhao@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stable-dep-of: 4fc82cd907 ("iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17cf8661ee ]
The endpoint controller loses the Maximum Link Width and Supported Link Speed
value from the Link Capabilities Register - initially configured by the Reset
Configuration Word (RCW) - during a link-down or hot reset event.
Address this issue in the endpoint event handler.
Link: https://lore.kernel.org/r/20230720135834.1977616-2-Frank.Li@nxp.com
Fixes: a805770d8a ("PCI: layerscape: Add EP mode support")
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 061cbfab09 ]
Layerscape has PME interrupt, which can be used as linkup notifier. Set
CFG_READY bit of PEX_PF0_CONFIG to enable accesses from root complex when
linkup detected.
Link: https://lore.kernel.org/r/20230515151049.2797105-1-Frank.Li@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit db744ddd59 upstream.
While calculating the hardware interrupt number for a MSI interrupt, the
higher bits (i.e. from bit-5 onwards a.k.a domain_nr >= 32) of the PCI
domain number gets truncated because of the shifted value casting to return
type of pci_domain_nr() which is 'int'. This for example is resulting in
same hardware interrupt number for devices 0019:00:00.0 and 0039:00:00.0.
To address this cast the PCI domain number to 'irq_hw_number_t' before left
shifting it to calculate the hardware interrupt number.
Please note that this fixes the issue only on 64-bit systems and doesn't
change the behavior for 32-bit systems i.e. the 32-bit systems continue to
have the issue. Since the issue surfaces only if there are too many PCIe
controllers in the system which usually is the case in modern server
systems and they don't tend to run 32-bit kernels.
Fixes: 3878eaefb8 ("PCI/MSI: Enhance core to support hierarchy irqdomain")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115135649.708536-1-vidyas@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5d1b4b46f upstream.
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd6 ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1291b716bb ]
When a device with AER detects an error, it logs error information in its
own AER Error Status registers. It may send an Error Message to the Root
Port (RCEC in the case of an RCiEP), which logs the fact that an Error
Message was received (Root Error Status) and the Requester ID of the
message source (Error Source Identification).
aer_print_port_info() prints the Requester ID from the Root Port Error
Source in the usual Linux "bb:dd.f" format, but when find_source_device()
finds no error details in the hierarchy below the Root Port, it printed the
raw Requester ID without decoding it.
Decode the Requester ID in the usual Linux format so it matches other
messages.
Sample message changes:
- pcieport 0000:00:1c.5: AER: Correctable error received: 0000:00:1c.5
- pcieport 0000:00:1c.5: AER: can't find device of ID00e5
+ pcieport 0000:00:1c.5: AER: Correctable error message received from 0000:00:1c.5
+ pcieport 0000:00:1c.5: AER: found no error details for 0000:00:1c.5
Link: https://lore.kernel.org/r/20231206224231.732765-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df25461119 ]
A PCI device hot removal may occur while stdev->cdev is held open. The call
to stdev_release() then happens during close or exit, at a point way past
switchtec_pci_remove(). Otherwise the last ref would vanish with the
trailing put_device(), just before return.
At that later point in time, the devm cleanup has already removed the
stdev->mmio_mrpc mapping. Also, the stdev->pdev reference was not a counted
one. Therefore, in DMA mode, the iowrite32() in stdev_release() will cause
a fatal page fault, and the subsequent dma_free_coherent(), if reached,
would pass a stale &stdev->pdev->dev pointer.
Fix by moving MRPC DMA shutdown into switchtec_pci_remove(), after
stdev_kill(). Counting the stdev->pdev ref is now optional, but may prevent
future accidents.
Reproducible via the script at
https://lore.kernel.org/r/20231113212150.96410-1-dns@arista.com
Link: https://lore.kernel.org/r/20231122042316.91208-2-dns@arista.com
Signed-off-by: Daniel Stodden <dns@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e585a37e50 ]
By running a Van Gogh device (Steam Deck), the following message
was noticed in the kernel log:
pci 0000:04:00.3: PCI class overridden (0x0c03fe -> 0x0c03fe) so dwc3 driver can claim this instead of xhci
Effectively this means the quirk executed but changed nothing, since the
class of this device was already the proper one (likely adjusted by newer
firmware versions).
Check and perform the override only if necessary.
Link: https://lore.kernel.org/r/20231120160531.361552-1-gpiccoli@igalia.com
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Vicki Pfau <vi@endrift.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed48c80b2 ]
Spectrum-{1,2,3,4} devices report that a D3hot->D0 transition causes a
reset (i.e., they advertise NoSoftRst-). However, this transition does
not have any effect on the device: It continues to be operational and
network ports remain up. Advertising this support makes it seem as if a
PM reset is viable for these devices. Mark it as unavailable to skip it
when testing reset methods.
Before:
# cat /sys/bus/pci/devices/0000\:03\:00.0/reset_method
pm bus
After:
# cat /sys/bus/pci/devices/0000\:03\:00.0/reset_method
bus
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ccc1318cf ]
When using the fls() helper, the translation table should be a power of
two; otherwise, the resulting value will not be correct.
For example, given fls(0x3e00000) - 1 = 25, the PCIe translation window
size will be set to 0x2000000 instead of the expected size 0x3e00000.
Fix the translation window by splitting the MMIO space into multiple tables
if its size is not a power of two.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231023081423.18559-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12ca110c6 ]
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4e11c29873 upstream.
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db6 ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2217fffcd6 upstream.
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f93e71aea6 upstream.
This reverts commit 08d0cc5f34.
Michael reported that when attempting to resume from suspend to RAM on ASUS
mini PC PN51-BB757MDE1 (DMI model: MINIPC PN51-E1), 08d0cc5f34
("PCI/ASPM: Remove pcie_aspm_pm_state_change()") caused a 12-second delay
with no output, followed by a reboot.
Workarounds include:
- Reverting 08d0cc5f34 ("PCI/ASPM: Remove pcie_aspm_pm_state_change()")
- Booting with "pcie_aspm=off"
- Booting with "pcie_aspm.policy=performance"
- "echo 0 | sudo tee /sys/bus/pci/devices/0000:03:00.0/link/l1_aspm"
before suspending
- Connecting a USB flash drive
Link: https://lore.kernel.org/r/20240102232550.1751655-1-helgaas@kernel.org
Fixes: 08d0cc5f34 ("PCI/ASPM: Remove pcie_aspm_pm_state_change()")
Reported-by: Michael Schaller <michael@5challer.de>
Link: https://lore.kernel.org/r/76c61361-b8b4-435f-a9f1-32b716763d62@5challer.de
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef61a04057 upstream.
This is a partial revert of 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") for MIPS-based Loongson.
Some MIPS Loongson systems don't support arbitrary Max_Read_Request_Size
(MRRS) settings. 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") worked around that by (1) assuming that firmware configured
MRRS to the maximum supported value and (2) preventing the PCI core from
increasing MRRS.
Unfortunately, some firmware doesn't set that maximum MRRS correctly, which
results in devices not being initialized correctly. One symptom, from the
Debian report below, is this:
ata4.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6 frozen
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/20:e8:00:f0:e1/00:00:00:00:00/40 tag 29 ncq dma 16384 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
Limit MRRS to 256 because MIPS Loongson with higher MRRS support is
considered rare.
This must be done at device enablement stage because the MRRS setting may
get lost if PCI_COMMAND_MASTER on the parent bridge is cleared, and we are
only sure parent bridge is enabled at this point.
Fixes: 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS increases")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217680
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1035587
Link: https://lore.kernel.org/r/20231201115028.84351-1-jiaxun.yang@flygoat.com
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5df12742b7 upstream.
This reverts commit 40613da52b and the
subsequent fix to it:
cc22522fd5 ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root bus")
40613da52b fixed a problem where hot-adding a device with large BARs
failed if the bridge windows programmed by firmware were not large enough.
cc22522fd5 ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources()
only for non-root bus") fixed a problem with 40613da52b13: an ACPI hot-add
of a device on a PCI root bus (common in the virt world) or firmware
sending ACPI Bus Check to non-existent Root Ports (e.g., on Dell Inspiron
7352/0W6WV0) caused a NULL pointer dereference and suspend/resume hangs.
Unfortunately the combination of 40613da52b and cc22522fd5 caused other
problems:
- Fiona reported that hot-add of SCSI disks in QEMU virtual machine fails
sometimes.
- Dongli reported a similar problem with hot-add of SCSI disks.
- Jonathan reported a console freeze during boot on bare metal due to an
error in radeon GPU initialization.
Revert both patches to avoid adding these problems. This means we will
again see the problems with hot-adding devices with large BARs and the NULL
pointer dereferences and suspend/resume issues that 40613da52b and
cc22522fd5 were intended to fix.
Fixes: 40613da52b ("PCI: acpiphp: Reassign resources on bridge if necessary")
Fixes: cc22522fd5 ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root bus")
Reported-by: Fiona Ebner <f.ebner@proxmox.com>
Closes: https://lore.kernel.org/r/9eb669c0-d8f2-431d-a700-6da13053ae54@proxmox.com
Reported-by: Dongli Zhang <dongli.zhang@oracle.com>
Closes: https://lore.kernel.org/r/3c4a446a-b167-11b8-f36f-d3c1b49b42e9@oracle.com
Reported-by: Jonathan Woithe <jwoithe@just42.net>
Closes: https://lore.kernel.org/r/ZXpaNCLiDM+Kv38H@marvin.atrad.com.au
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a07d2497ed ]
The DWC core driver exposes the write_dbi2() callback for writing to the
DBI2 registers in a vendor-specific way.
On the Qcom EP platforms, the DBI_CS2 bit in the ELBI region needs to be
asserted before writing to any DBI2 registers and deasserted once done.
So, let's implement the callback for the Qcom PCIe EP driver so that the
DBI2 writes are correctly handled in the hardware.
Without this callback, the DBI2 register writes like BAR size won't go
through and as a result, the default BAR size is set for all BARs.
[kwilczynski: commit log, renamed function to match the DWC convention]
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231025130029.74693-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: stable@vger.kernel.org # 5.16+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9260693aa ]
Commit ac91e69805 ("PCI: Unify delay handling for reset and resume")
shortened an unconditional 1 sec delay after a Secondary Bus Reset to 100
msec for PCIe (per PCIe r6.1 sec 6.6.1). The 1 sec delay is only required
for Conventional PCI.
But it turns out that there are PCIe devices which require a longer delay
than prescribed before first config space access after reset recovery or
resume from D3cold:
Chad reports that a "VideoPropulsion Torrent QN16e" MPEG QAM Modulator
"raises a PCI system error (PERR), as reported by the IPMI event log, and
the hardware itself would suffer a catastrophic event, cycling the server"
unless the longer delay is observed.
The card is specified to conform to PCIe r1.0 and indeed only supports Gen1
speed (2.5 GT/s) according to lspci. PCIe r1.0 sec 7.6 prescribes the same
100 msec delay as PCIe r6.1 sec 6.6.1:
To allow components to perform internal initialization, system software
must wait for at least 100 ms from the end of a reset (cold/warm/hot)
before it is permitted to issue Configuration Requests
The behavior of the Torrent QN16e card thus appears to be a quirk. Treat
it as such and lengthen the reset delay for this specific device.
Fixes: ac91e69805 ("PCI: Unify delay handling for reset and resume")
Link: https://lore.kernel.org/r/47727e792c7f0282dc144e3ec8ce8eb6e713394e.1695304512.git.lukas@wunner.de
Reported-by: Chad Schroeder <CSchroeder@sonifi.com>
Closes: https://lore.kernel.org/linux-pci/DM6PR16MB2844903E34CAB910082DF019B1FAA@DM6PR16MB2844.namprd16.prod.outlook.com/
Tested-by: Chad Schroeder <CSchroeder@sonifi.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 83a939f0fd upstream.
With CONFIG_PCI_EXYNOS=y and exynos_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
WARNING: modpost: drivers/pci/controller/dwc/pci-exynos: section mismatch in reference: exynos_pcie_driver+0x8 (section: .data) -> exynos_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 340cba6092 ("pci: Add PCIe driver for Samsung Exynos")
Link: https://lore.kernel.org/r/20231001170254.2506508-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3064ef2e88 upstream.
With CONFIG_PCIE_KIRIN=y and kirin_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
drivers/pci/controller/dwc/pcie-kirin: section mismatch in reference: kirin_pcie_driver+0x8 (section: .data) -> kirin_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 000f60db78 ("PCI: kirin: Add support for a PHY layer")
Link: https://lore.kernel.org/r/20231001170254.2506508-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e37372ad0 upstream.
aspm_attr_store_common(), which handles sysfs control of ASPM, has the same
problem as fb097dcd5a ("PCI/ASPM: Disable only ASPM_STATE_L1 when driver
disables L1"): disabling L1 adds only ASPM_L1 (but not any of the L1.x
substates) to the "aspm_disable" mask.
Enabling one substate, e.g., L1.1, via sysfs removes ASPM_L1 from the
disable mask. Since disabling L1 via sysfs doesn't add any of the
substates to the disable mask, enabling L1.1 actually enables *all* the
substates.
In this scenario:
- Write 0 to "l1_aspm" to disable L1
- Write 1 to "l1_1_aspm" to enable L1.1
the intention is to disable L1 and all L1.x substates, then enable just
L1.1, but in fact, *all* L1.x substates are enabled.
Fix this by explicitly disabling all the L1.x substates when disabling L1.
Fixes: 72ea91afbf ("PCI/ASPM: Add sysfs attributes for controlling ASPM link states")
Link: https://lore.kernel.org/r/6ba7dd79-9cfe-4ed0-a002-d99cb842f361@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7994db905c upstream.
The __init annotation makes the ks_pcie_probe() function disappear after
booting completes. However a device can also be bound later. In that case,
we try to call ks_pcie_probe(), but the backing memory is likely already
overwritten.
The right thing to do is do always have the probe callback available. Note
that the (wrong) __refdata annotation prevented this issue to be noticed by
modpost.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 200bddbb3f upstream.
With CONFIG_PCIE_KEYSTONE=y and ks_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
Note that this driver cannot be compiled as a module, so ks_pcie_remove()
was always discarded before this change and modpost couldn't warn about
this issue. Furthermore the __ref annotation also prevents a warning.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70b70a4307 upstream.
struct pci_dev contains two flags which govern whether the device may
suspend to D3cold:
* no_d3cold provides an opt-out for drivers (e.g. if a device is known
to not wake from D3cold)
* d3cold_allowed provides an opt-out for user space (default is true,
user space may set to false)
Since commit 9d26d3a8f1 ("PCI: Put PCIe ports into D3 during suspend"),
the user space setting overwrites the driver setting. Essentially user
space is trusted to know better than the driver whether D3cold is
working.
That feels unsafe and wrong. Assume that the change was introduced
inadvertently and do not overwrite no_d3cold when d3cold_allowed is
modified. Instead, consider d3cold_allowed in addition to no_d3cold
when choosing a suspend state for the device.
That way, user space may opt out of D3cold if the driver hasn't, but it
may no longer force an opt in if the driver has opted out.
Fixes: 9d26d3a8f1 ("PCI: Put PCIe ports into D3 during suspend")
Link: https://lore.kernel.org/r/b8a7f4af2b73f6b506ad8ddee59d747cbf834606.1695025365.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04e82fa595 ]
Use FIELD_GET() to remove dependences on the field position, i.e., the
shift value. No functional change intended.
Separate because this isn't as trivial as the other FIELD_GET() changes.
See 907830b0fc ("PCI: Add a REBAR size quirk for Sapphire RX 5600 XT
Pulse")
Link: https://lore.kernel.org/r/20231010204436.1000644-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18615b1cf ]
Due to a hardware issue in A and B steppings of Intel IPU E2000, it expects
wrong endianness in ATS invalidation message body. This problem can lead to
outdated translations being returned as valid and finally cause system
instability.
To prevent such issues, add quirk_intel_e2000_no_ats() to disable ATS for
vulnerable IPU E2000 devices.
Link: https://lore.kernel.org/r/20230908143606.685930-3-bartosz.pawlowski@intel.com
Signed-off-by: Bartosz Pawlowski <bartosz.pawlowski@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f18b1137d3 ]
Introduce quirk_no_ats() helper function to provide a standard way to
disable ATS capability in PCI quirks.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230908143606.685930-2-bartosz.pawlowski@intel.com
Signed-off-by: Bartosz Pawlowski <bartosz.pawlowski@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1f9b39da4 ]
Use FIELD_GET() to extract PCIe Negotiated and Maximum Link Width fields
instead of custom masking and shifting.
Link: https://lore.kernel.org/r/20230919125648.1920-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: drop duplicate include of <linux/bitfield.h>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d15f18053e ]
Placing PCI error code check inside "if" condition usually results in need
to split lines. Combined with additional conditions the "if" condition
becomes messy.
Convert to the usual error handling pattern with an additional variable to
improve code readability. In addition, reverse the logic in
pci_find_vsec_capability() to get rid of &&.
No functional changes intended.
Link: https://lore.kernel.org/r/20230911125354.25501-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: PCI_POSSIBLE_ERROR()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 408599ec56 ]
mvebu_pcie_setup_hw() setups the Maximum Link Width field in the Link
Capabilities registers using an open-coded variant of FIELD_PREP() with
a literal in shift. Improve readability by using
FIELD_PREP(PCI_EXP_LNKCAP_MLW, ...).
Link: https://lore.kernel.org/r/20230919125648.1920-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 759574abd7 ]
Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.
Similarly, change custom code that misleadingly used
PCI_EXP_LNKSTA_NLW_SHIFT to prepare value for PCI_EXP_LNKCAP write
to use FIELD_PREP() with correct field define (PCI_EXP_LNKCAP_MLW).
Link: https://lore.kernel.org/r/20230919125648.1920-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5827e17d05 ]
vmd_domain_reset() attempts to find whether the device may contain multiple
functions by checking 0x80 (Multi-Function Device), however, the hdr_type
variable has already been masked with PCI_HEADER_TYPE_MASK so the check can
never true.
To fix the issue, don't mask the read with PCI_HEADER_TYPE_MASK.
Fixes: 6aab562229 ("PCI: vmd: Clean up domain before enumeration")
Link: https://lore.kernel.org/r/20231003125300.5541-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7e6f3b6d2c upstream.
The AMD VanGogh SoC contains a DesignWare USB3 Dual-Role Device that can be
operated as either a USB Host or a USB Device, similar to on the AMD Nolan
platform.
be6646bfba ("PCI: Prevent xHCI driver from claiming AMD Nolan USB3 DRD
device") added a quirk to let the dwc3 driver claim the Nolan device since
it provides more specific support.
Extend that quirk to include the VanGogh SoC USB3 device.
Link: https://lore.kernel.org/r/20230927202212.2388216-1-vi@endrift.com
Signed-off-by: Vicki Pfau <vi@endrift.com>
[bhelgaas: include be6646bfba reference, add stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a878a54d0 upstream.
PARF_SLV_ADDR_SPACE_SIZE_2_3_3 is used by qcom_pcie_post_init_2_3_3().
This PCIe slave address space size register offset is 0x358 but was
incorrectly changed to 0x16c by 39171b33f6 ("PCI: qcom: Remove PCIE20_
prefix from register definitions").
This prevented access to slave address space registers like iATU, etc.,
so the IPQ8074 PCIe controller was not enumerated.
Revert back to the correct 0x358 offset and remove the unused
PARF_SLV_ADDR_SPACE_SIZE_2_3_3.
Fixes: 39171b33f6 ("PCI: qcom: Remove PCIE20_ prefix from register definitions")
Link: https://lore.kernel.org/r/20230919102948.1844909-1-quic_srichara@quicinc.com
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 551a60e122 ]
The iMSI-RX module of the DW PCIe controller provides multiple sets of
MSI_CTRL_INT_i_* registers, and each set is capable of handling 32 MSI
interrupts. However, the fu740 PCIe controller driver only enabled one set
of MSI_CTRL_INT_i_* registers, as the total number of supported interrupts
was not specified.
Set the supported number of MSI vectors to enable all the MSI_CTRL_INT_i_*
registers on the fu740 PCIe core, allowing the system to fully utilize the
available MSI interrupts.
Link: https://lore.kernel.org/r/20230807055621.2431-1-yongxuan.wang@sifive.com
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f73eedc90b ]
During domain reset process vmd_domain_reset() clears PCI
configuration space of VMD root ports. But certain platform
has observed following errors and failed to boot.
...
DMAR: VT-d detected Invalidation Queue Error: Reason f
DMAR: VT-d detected Invalidation Time-out Error: SID ffff
DMAR: VT-d detected Invalidation Completion Error: SID ffff
DMAR: QI HEAD: UNKNOWN qw0 = 0x0, qw1 = 0x0
DMAR: QI PRIOR: UNKNOWN qw0 = 0x0, qw1 = 0x0
DMAR: Invalidation Time-out Error (ITE) cleared
The root cause is that memset_io() clears prefetchable memory base/limit
registers and prefetchable base/limit 32 bits registers sequentially.
This seems to be enabling prefetchable memory if the device disabled
prefetchable memory originally.
Here is an example (before memset_io()):
PCI configuration space for 10000:00:00.0:
86 80 30 20 06 00 10 00 04 00 04 06 00 00 01 00
00 00 00 00 00 00 00 00 00 01 01 00 00 00 00 20
00 00 00 00 01 00 01 00 ff ff ff ff 75 05 00 00
...
So, prefetchable memory is ffffffff00000000-575000fffff, which is
disabled. When memset_io() clears prefetchable base 32 bits register,
the prefetchable memory becomes 0000000000000000-575000fffff, which is
enabled and incorrect.
Here is the quote from section 7.5.1.3.9 of PCI Express Base 6.0 spec:
The Prefetchable Memory Limit register must be programmed to a smaller
value than the Prefetchable Memory Base register if there is no
prefetchable memory on the secondary side of the bridge.
This is believed to be the reason for the failure and in addition the
sequence of operation in vmd_domain_reset() is not following the PCIe
specs.
Disable the bridge window by executing a sequence of operations
borrowed from pci_disable_bridge_window() and pci_setup_bridge_io(),
that comply with the PCI specifications.
Link: https://lore.kernel.org/r/20230810215029.1177379-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michael Kelley