[ Upstream commit 321da3dc1f ]
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cf33e6ca12 which is
commit d094956581 upstream.
It is known to cause problems and has asked to be dropped.
Link: https://lore.kernel.org/r/yq1frvvpymp.fsf@ca-mkp.ca.oracle.com
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Sasha Levin <sashal@kernel.org>
Reported-by: John David Anglin <dave.anglin@bell.net>
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b73dd5f999 which is
commit 321da3dc1f upstream.
It is known to cause problems and has asked to be dropped.
Link: https://lore.kernel.org/r/yq1frvvpymp.fsf@ca-mkp.ca.oracle.com
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Sasha Levin <sashal@kernel.org>
Reported-by: John David Anglin <dave.anglin@bell.net>
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ae917d4bc ]
The call to lpfc_sli4_resume_rpi() in lpfc_rcv_padisc() may return an
unsuccessful status. In such cases, the elsiocb is not issued, the
completion is not called, and thus the elsiocb resource is leaked.
Check return value after calling lpfc_sli4_resume_rpi() and conditionally
release the elsiocb resource.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240131185112.149731-3-justintee8345@gmail.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0296bea01c ]
"if device_add() succeeds, you should call device_del() when you want to
get rid of it."
In sd_probe(), device_add_disk() fails when device_add() has already
succeeded, so change put_device() to device_unregister() to ensure device
resources are released.
Fixes: 2a7a891f4c ("scsi: sd: Add error handling support for add_disk()")
Signed-off-by: Li Nan <linan122@huawei.com>
Link: https://lore.kernel.org/r/20231208082335.1754205-1-linan666@huaweicloud.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1197c5b209 ]
The myrb and myrs drivers use an odd way of implementing their sysfs files,
calling snprintf() with a fixed length of 32 bytes to print into a page
sized buffer. One of the strings is actually longer than 32 bytes, which
clang can warn about:
drivers/scsi/myrb.c:1906:10: error: 'snprintf' will always be truncated; specified size is 32, but format string expands to at least 34 [-Werror,-Wformat-truncation]
drivers/scsi/myrs.c:1089:10: error: 'snprintf' will always be truncated; specified size is 32, but format string expands to at least 34 [-Werror,-Wformat-truncation]
These could all be plain sprintf() without a length as the buffer is always
long enough. On the other hand, sysfs files should not be overly long
either, so just double the length to make sure the longest strings don't
get truncated here.
Fixes: 7726618639 ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Fixes: 081ff398c5 ("scsi: myrb: Add Mylex RAID controller (block interface)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240326223825.4084412-8-arnd@kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e68a458bc upstream.
As of commit d8649fc1c5 ("scsi: libsas: Do discovery on empty PHY to
update PHY info"), do discovery will send a new SMP_DISCOVER and update
phy->phy_change_count. We found that if the disk is reconnected and phy
change_count changes at this time, the disk scanning process will not be
triggered.
Therefore, call sas_set_ex_phy() to update the PHY info with the results of
the last query. And because the previous phy info will be used when calling
sas_unregister_devs_sas_addr(), sas_unregister_devs_sas_addr() should be
called before sas_set_ex_phy().
Fixes: d8649fc1c5 ("scsi: libsas: Do discovery on empty PHY to update PHY info")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240307141413.48049-3-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a57345279f upstream.
Add a helper to get attached_sas_addr and device type from disc_resp.
Suggested-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240307141413.48049-2-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28d4199118 upstream.
The wqe is of type lpfc_wqe128. It should be memset with the same type.
Fixes: 6c621a2229 ("scsi: lpfc: Separate NVMET RQ buffer posting from IO resources SGL/iocbq/context")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240304090649.833953-1-usama.anjum@collabora.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Justin Tee <justintee8345@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16cc2ba71b upstream.
The cmdwqe and rspwqe are of type lpfc_wqe128. They should be memset() with
the same type.
Fixes: 61910d6a52 ("scsi: lpfc: SLI path split: Refactor CT paths")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240304091119.847060-1-usama.anjum@collabora.com
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 591c1fdf20 upstream.
Currently when PCI error is detected, I/O is aborted manually through the
ABORT IOCB mechanism which is not guaranteed to succeed.
Instead, wait for the OS or system to notify driver to wind down I/O
through the pci_error_handlers api. Set eeh_busy flag to pause all traffic
and wait for I/O to drain.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240227164127.36465-11-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5a3084072 upstream.
Upon driver unload, purge_mbox flag is set and the heartbeat monitor thread
detects this flag and does not send the mailbox command down to FW with a
debug message "Error detected: purge[1] eeh[0] cmd=0x0, Exiting". This
being not a real error, change the debug message.
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240227164127.36465-10-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69aecdd410 upstream.
Changing of [FCP|NVME] prefer flag in flash has no effect on driver. For
device that supports both FCP + NVMe over the same connection, driver
continues to connect to this device using the previous successful login
mode.
On completion of flash update, adapter will be reset. Driver will
reset the prefer flag based on setting from flash.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240227164127.36465-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76a192e1a5 upstream.
Current code combines the allocation of FCE|EFT trace buffers and enables
the features all in 1 step.
Split this step into separate steps in preparation for follow-on patch to
allow user to have a choice to enable / disable FCE trace feature.
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240227164127.36465-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 881eb861ca upstream.
Disk failed to rediscover after chip reset error injection. The chip reset
happens at the time when a PLOGI is being sent. This causes a flag to be
left on which blocks the retry. Clear the blocking flag.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240227164127.36465-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4895009c4b upstream.
Currently IOCBs are allowed to push through while chip reset could be in
progress. During chip reset the outstanding_cmds array is cleared
twice. Once when any command on this array is returned as failed and
secondly when the array is initialize to zero. If a command is inserted on
to the array between these intervals, then the command will be lost. Check
for chip reset before sending IOCB.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20240227164127.36465-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c76106cb9 upstream.
Commit 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop
management") introduced the manage_system_start_stop scsi_device flag to
allow libata to indicate to the SCSI disk driver that nothing should be
done when resuming a disk on system resume. This change turned the
execution of sd_resume() into a no-op for ATA devices on system
resume. While this solved deadlock issues during device resume, this change
also wrongly removed the execution of opal_unlock_from_suspend(). As a
result, devices with TCG OPAL locking enabled remain locked and
inaccessible after a system resume from sleep.
To fix this issue, introduce the SCSI driver resume method and implement it
with the sd_resume() function calling opal_unlock_from_suspend(). The
former sd_resume() function is renamed to sd_resume_common() and modified
to call the new sd_resume() function. For non-ATA devices, this result in
no functional changes.
In order for libata to explicitly execute sd_resume() when a device is
resumed during system restart, the function scsi_resume_device() is
introduced. libata calls this function from the revalidation work executed
on devie resume, a state that is indicated with the new device flag
ATA_DFLAG_RESUMING. Doing so, locked TCG OPAL enabled devices are unlocked
on resume, allowing normal operation.
Fixes: 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop management")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218538
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240319071209.1179257-1-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f23a4d6e07 upstream.
Commit fc663711b9 ("scsi: core: Remove the /proc/scsi/${proc_name}
directory earlier") fixed a bug related to modules loading/unloading, by
adding a call to scsi_proc_hostdir_rm() on scsi_remove_host(). But that led
to a potential duplicate call to the hostdir_rm() routine, since it's also
called from scsi_host_dev_release(). That triggered a regression report,
which was then fixed by commit be03df3d4b ("scsi: core: Fix a procfs host
directory removal regression"). The fix just dropped the hostdir_rm() call
from dev_release().
But it happens that this proc directory is created on scsi_host_alloc(),
and that function "pairs" with scsi_host_dev_release(), while
scsi_remove_host() pairs with scsi_add_host(). In other words, it seems the
reason for removing the proc directory on dev_release() was meant to cover
cases in which a SCSI host structure was allocated, but the call to
scsi_add_host() didn't happen. And that pattern happens to exist in some
error paths, for example.
Syzkaller causes that by using USB raw gadget device, error'ing on
usb-storage driver, at usb_stor_probe2(). By checking that path, we can see
that the BadDevice label leads to a scsi_host_put() after a SCSI host
allocation, but there's no call to scsi_add_host() in such path. That leads
to messages like this in dmesg (and a leak of the SCSI host proc
structure):
usb-storage 4-1:87.51: USB Mass Storage device detected
proc_dir_entry 'scsi/usb-storage' already registered
WARNING: CPU: 1 PID: 3519 at fs/proc/generic.c:377 proc_register+0x347/0x4e0 fs/proc/generic.c:376
The proper fix seems to still call scsi_proc_hostdir_rm() on dev_release(),
but guard that with the state check for SHOST_CREATED; there is even a
comment in scsi_host_dev_release() detailing that: such conditional is
meant for cases where the SCSI host was allocated but there was no calls to
{add,remove}_host(), like the usb-storage case.
This is what we propose here and with that, the error path of usb-storage
does not trigger the warning anymore.
Reported-by: syzbot+c645abf505ed21f931b5@syzkaller.appspotmail.com
Fixes: be03df3d4b ("scsi: core: Fix a procfs host directory removal regression")
Cc: stable@vger.kernel.org
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20240313113006.2834799-1-gpiccoli@igalia.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b69600231f ]
Some callback functions used here take a boolean argument, others take a
status argument. This breaks KCFI type checking, so clang now warns about
the function pointer cast:
drivers/scsi/bfa/bfad_bsg.c:2138:29: error: cast from 'void (*)(void *, enum bfa_status)' to 'bfa_cb_cbfn_t' (aka 'void (*)(void *, enum bfa_boolean)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Assuming the code is actually correct here and the callers always match the
argument types of the callee, rework this to replace the explicit cast with
a union of the two pointer types. This does not change the behavior of the
code, so if something is actually broken here, a larger rework may be
necessary.
Fixes: 37ea0558b8 ("[SCSI] bfa: Added support to collect and reset fcport stats")
Fixes: 3ec4f2c8bf ("[SCSI] bfa: Added support to configure QOS and collect stats.")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240222124433.2046570-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f3dbcb563 ]
csiostor uses function pointer casts to keep the csio_ln_ev state machine
hidden, but this causes warnings about control flow integrity (KCFI)
violations in clang-16 and higher:
drivers/scsi/csiostor/csio_lnode.c:1098:33: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1098 | return (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1369:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1369 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_uninit)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1373:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1373 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1377:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1377 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_offline)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Move the enum into a shared header so the correct types can be used without
the need for casts.
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213100518.457623-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0017c3ed ]
If the driver detects that the controller is not ready before sending the
first IOC facts command, it will wait for a maximum of 10 seconds for it to
become ready. However, even if the controller becomes ready within 10
seconds, the driver will still issue a diagnostic reset.
Modify the driver to avoid sending a diag reset if the controller becomes
ready within the 10-second wait time.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240221071724.14986-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 321da3dc1f ]
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d094956581 ]
Move the SCSI execution functions to use a struct for passing in optional
args. This commit adds the new struct, temporarily converts scsi_execute()
and scsi_execute_req() ands a new helper, scsi_execute_cmd(), which takes
the scsi_exec_args struct.
There should be no change in behavior. We no longer allow users to pass in
any request->rq_flags value, but they were only passing in RQF_PM which we
do support by allowing users to pass in the BLK_MQ_REQ flags used by
blk_mq_alloc_request().
Subsequent commits will convert scsi_execute() and scsi_execute_req() users
to the new helpers then remove scsi_execute() and scsi_execute_req().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 321da3dc1f ("scsi: sd: usb_storage: uas: Access media prior to querying device properties")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ddf190a7d ]
JAZZ_ESP is a bool kconfig symbol that selects SCSI_SPI_ATTRS. When
CONFIG_SCSI=m, this results in SCSI_SPI_ATTRS=m while JAZZ_ESP=y, which
causes many undefined symbol linker errors.
Fix this by only offering to build this driver when CONFIG_SCSI=y.
[mkp: JAZZ_ESP is unique in that it does not support being compiled as a
module unlike the remaining SPI SCSI HBA drivers]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20240214055953.9612-1-rdunlap@infradead.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402112222.Gl0udKyU-lkp@intel.com/
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b5fc07a5fb upstream.
Commit c92a6b5d63 ("scsi: core: Query VPD size before getting full
page") removed the logic which checks whether a VPD page is present on
the supported pages list before asking for the page itself. That was
done because SPC helpfully states "The Supported VPD Pages VPD page
list may or may not include all the VPD pages that are able to be
returned by the device server". Testing had revealed a few devices
that supported some of the 0xBn pages but didn't actually list them in
page 0.
Julian Sikorski bisected a problem with his drive resetting during
discovery to the commit above. As it turns out, this particular drive
firmware will crash if we attempt to fetch page 0xB9.
Various approaches were attempted to work around this. In the end,
reinstating the logic that consults VPD page 0 before fetching any
other page was the path of least resistance. A firmware update for the
devices which originally compelled us to remove the check has since
been released.
Link: https://lore.kernel.org/r/20240214221411.2888112-1-martin.petersen@oracle.com
Fixes: c92a6b5d63 ("scsi: core: Query VPD size before getting full page")
Cc: stable@vger.kernel.org
Cc: Bart Van Assche <bvanassche@acm.org>
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Reviewed-by: Lee Duncan <lee.duncan@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6c1b19153 ]
LUNs going into "failed ready running" state observed on >1T and on even
numbers of size (2T, 4T, 6T, 8T and 10T). The issue occurs when DIF is
enabled at the host.
The kernel logs:
Cannot setup S/G List for HBAIO segs 1/1 SGL 512 SCSI 256: 3 0
The host lpfc driver is failing to setup scatter/gather list (protection
data) for the I/Os.
The return type lpfc_bg_setup_sgl()/lpfc_bg_setup_sgl_prot() causes the
compiler to remove the most significant bit. Use an unsigned type instead.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[dwagner: added commit message]
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Link: https://lore.kernel.org/r/20231220162658.12392-1-dwagner@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 977fe773dc upstream.
This reverts commit 1a19755519.
This commit causes interrupts to be lost for FCoE devices, since it changed
sping locks from "bh" to "irqsave".
Instead, a work queue should be used, and will be addressed in a separate
commit.
Fixes: 1a19755519 ("scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock")
Signed-off-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/c578cdcd46b60470535c4c4a953e6a1feca0dffd.1707500786.git.lduncan@suse.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4469f3858 upstream.
Current code uses the specified ring buffer size (either the default of 128
Kbytes or a module parameter specified value) to encompass the one page
ring buffer header plus the actual ring itself. When the page size is 4K,
carving off one page for the header isn't significant. But when the page
size is 64K on ARM64, only half of the default 128 Kbytes is left for the
actual ring. While this doesn't break anything, the smaller ring size
could be a performance bottleneck.
Fix this by applying the VMBUS_RING_SIZE macro to the specified ring buffer
size. This macro adds a page for the header, and rounds up the size to a
page boundary, using the page size for which the kernel is built. Use this
new size for subsequent ring buffer calculations. For example, on ARM64
with 64K page size and the default ring size, this results in the actual
ring being 128 Kbytes, which is intended.
Cc: stable@vger.kernel.org # 5.15.x
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240122170956.496436-1-mhklinux@outlook.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e6c901199 ]
Commit 4373534a98 ("scsi: core: Move scsi_host_busy() out of host lock
for waking up EH handler") intended to fix a hard lockup issue triggered by
EH. The core idea was to move scsi_host_busy() out of the host lock when
processing individual commands for EH. However, a suggested style change
inadvertently caused scsi_host_busy() to remain under the host lock. Fix
this by calling scsi_host_busy() outside the lock.
Fixes: 4373534a98 ("scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler")
Cc: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240203024521.2006455-1-ming.lei@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4373534a98 ]
Inside scsi_eh_wakeup(), scsi_host_busy() is called & checked with host
lock every time for deciding if error handler kthread needs to be waken up.
This can be too heavy in case of recovery, such as:
- N hardware queues
- queue depth is M for each hardware queue
- each scsi_host_busy() iterates over (N * M) tag/requests
If recovery is triggered in case that all requests are in-flight, each
scsi_eh_wakeup() is strictly serialized, when scsi_eh_wakeup() is called
for the last in-flight request, scsi_host_busy() has been run for (N * M -
1) times, and request has been iterated for (N*M - 1) * (N * M) times.
If both N and M are big enough, hard lockup can be triggered on acquiring
host lock, and it is observed on mpi3mr(128 hw queues, queue depth 8169).
Fix the issue by calling scsi_host_busy() outside the host lock. We don't
need the host lock for getting busy count because host the lock never
covers that.
[mkp: Drop unnecessary 'busy' variables pointed out by Bart]
Cc: Ewan Milne <emilne@redhat.com>
Fixes: 6eb045e092 ("scsi: core: avoid host-wide host_busy counter for scsi_mq")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240112070000.4161982-1-ming.lei@redhat.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com>
Tested-by: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 658365c6b0 ]
Clang static complains that Value stored to 'status' is never read. Return
'status' rather than 'SCI_SUCCESS'.
Fixes: f1f52e7593 ("isci: uplevel request infrastructure")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20240112041926.3924315-1-suhui@nfschina.com
Reviewed-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce26497c74 ]
Currently in directly attached scenario, the phyup event
HISI_PHYE_PHY_UP_PM is notified before .phy_attached is set - this may
cause the phyup work hisi_sas_bytes_dmaed() execution failed and the
attached device will not be found.
To fix it, set .phy_attached before notifing phyup event.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53122a49f4 ]
We should set the status to FC_TIMED_OUT when a timeout error is passed to
fc_fcp_rec_error().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231129165832.224100-3-hare@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b57c4db5d2 ]
The current FC error recovery is sending up to three REC (recovery) frames
in 10 second intervals, and as a final step sending an ABTS after 30
seconds for the command itself. Unfortunately sending an ABTS is also the
action for the SCSI abort handler, and the default timeout for SCSI
commands is also 30 seconds. This causes two ABTS to be scheduled, with the
libfc one slightly earlier. The ABTS scheduled by SCSI EH then sees the
command to be already aborted, and will always return with a 'GOOD' status
irrespective on the actual result from the first ABTS. This causes the
SCSI EH abort handler to always succeed, and SCSI EH never to be engaged.
Fix this by not issuing an ABTS when a SCSI command is present for the
exchange, but rather wait for the abort scheduled from SCSI EH. And warn
if an abort is already scheduled to avoid similar errors in the future.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231129165832.224100-2-hare@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9260ff28e ]
Add PCI IDs checks for the cases where SAS5116 diverges from SAS4116 in
behavior.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20231123160132.4155-3-sumit.saxena@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5779b5292 ]
Because file_name and phba->ModelName are both declared a size 80 bytes,
the extra ".grp" file extension could cause an overflow into file_name.
Define a ELX_FW_NAME_SIZE macro with value 84. 84 incorporates the 4 extra
characters from ".grp". file_name is changed to be declared as a char and
initialized to zeros i.e. null chars.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20231031191224.150862-3-justintee8345@gmail.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f8fb3f3914 upstream.
If a controller reset is underway or the controller is in an unrecoverable
state, the PEL enable management command will be returned as EAGAIN or
EFAULT.
Cc: <stable@vger.kernel.org> # v6.1+
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-4-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73e33f969e ]
In function debugfs_debugfs_snapshot_global_reg_v3_hw() it uses
debugfs_axi_reg.count (which is the number of axi debugfs registers) to
acquire the number of global debugfs registers.
Use debugfs_global_reg.count to acquire the number of global debugfs
registers instead.
Fixes: 623a4b6d5c ("scsi: hisi_sas: Move debugfs code to v3 hw driver")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-6-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ea3e7763c ]
We obtain the semaphore and set HISI_SAS_RESETTING_BIT in
hisi_sas_reset_prepare_v3_hw(), block the scsi host and set
HISI_SAS_REJECT_CMD_BIT in hisi_sas_controller_reset_prepare(), released
them in hisi_sas_controller_reset_done(). However, if the HW reset failure
in FLR results in early return, the semaphore and flag bits will not be
release.
Rollback some operations including clearing flags / releasing semaphore
when FLR is failed.
Fixes: e5ea48014a ("scsi: hisi_sas: Implement handlers of PCIe FLR for v3 hw")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-5-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d34ee53570 ]
In function hisi_sas_controller_prereset(), -ENOSYS (Function not
implemented) should be returned if the driver does not support .soft_reset.
Returns -EPERM (Operation not permitted) if HISI_SAS_RESETTING_BIT is
already be set.
In function _suspend_v3_hw(), returns -EPERM (Operation not permitted) if
HISI_SAS_RESETTING_BIT is already be set.
Fixes: 4522204ab2 ("scsi: hisi_sas: tidy host controller reset function a bit")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5f27a332a ]
In fnic_init_module() exists redundant check for return value from
fnic_debugfs_init(), because at moment it only can return zero. It make
sense to process theoretical vmalloc() failure.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 9730ddfb12 ("scsi: fnic: remove redundant assignment of variable rc")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Link: https://lore.kernel.org/r/20231128111008.2280507-1-artem.chernyshev@red-soft.ru
Reviewed-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 066c5b46b6 upstream.
In commit 8930a6c207 ("scsi: core: add support for request batching") the
block layer bd->last flag was mapped to SCMD_LAST and used as an indicator
to send the batch for the drivers that implement this feature. However, the
error handling code was not updated accordingly.
scsi_send_eh_cmnd() is used to send error handling commands and request
sense. The problem is that request sense comes as a single command that
gets into the batch queue and times out. As a result the device goes
offline after several failed resets. This was observed on virtio_scsi
during a device resize operation.
[ 496.316946] sd 0:0:4:0: [sdd] tag#117 scsi_eh_0: requesting sense
[ 506.786356] sd 0:0:4:0: [sdd] tag#117 scsi_send_eh_cmnd timeleft: 0
[ 506.787981] sd 0:0:4:0: [sdd] tag#117 abort
To fix this always set SCMD_LAST flag in scsi_send_eh_cmnd() and
scsi_reset_ioctl().
Fixes: 8930a6c207 ("scsi: core: add support for request batching")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Atanasov <alexander.atanasov@virtuozzo.com>
Link: https://lore.kernel.org/r/20231215121008.2881653-1-alexander.atanasov@virtuozzo.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5becf57dd upstream.
This reverts commit 9dc704dcc0.
Several reports have been made indicating that this commit caused
hangs. Numerous attempts at root causing and fixing the issue have
been unsuccessful so let's revert for now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217599
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08c94d80b2 ]
skb_share_check() already drops the reference to the skb when returning
NULL. Using kfree_skb() in the error handling path leads to an skb double
free.
Fix this by removing the variable tmp_skb, and return directly when
skb_share_check() returns NULL.
Fixes: 01a4cc4d0c ("bnx2fc: do not add shared skbs to the fcoe_rx_list")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20221114110626.526643-1-weiyongjun@huaweicloud.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
