[ Upstream commit 321da3dc1f ]
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b73dd5f999 which is
commit 321da3dc1f upstream.
It is known to cause problems and has asked to be dropped.
Link: https://lore.kernel.org/r/yq1frvvpymp.fsf@ca-mkp.ca.oracle.com
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Tasos Sahanidis <tasos@tasossah.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Sasha Levin <sashal@kernel.org>
Reported-by: John David Anglin <dave.anglin@bell.net>
Reported-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0296bea01c ]
"if device_add() succeeds, you should call device_del() when you want to
get rid of it."
In sd_probe(), device_add_disk() fails when device_add() has already
succeeded, so change put_device() to device_unregister() to ensure device
resources are released.
Fixes: 2a7a891f4c ("scsi: sd: Add error handling support for add_disk()")
Signed-off-by: Li Nan <linan122@huawei.com>
Link: https://lore.kernel.org/r/20231208082335.1754205-1-linan666@huaweicloud.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0c76106cb9 upstream.
Commit 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop
management") introduced the manage_system_start_stop scsi_device flag to
allow libata to indicate to the SCSI disk driver that nothing should be
done when resuming a disk on system resume. This change turned the
execution of sd_resume() into a no-op for ATA devices on system
resume. While this solved deadlock issues during device resume, this change
also wrongly removed the execution of opal_unlock_from_suspend(). As a
result, devices with TCG OPAL locking enabled remain locked and
inaccessible after a system resume from sleep.
To fix this issue, introduce the SCSI driver resume method and implement it
with the sd_resume() function calling opal_unlock_from_suspend(). The
former sd_resume() function is renamed to sd_resume_common() and modified
to call the new sd_resume() function. For non-ATA devices, this result in
no functional changes.
In order for libata to explicitly execute sd_resume() when a device is
resumed during system restart, the function scsi_resume_device() is
introduced. libata calls this function from the revalidation work executed
on devie resume, a state that is indicated with the new device flag
ATA_DFLAG_RESUMING. Doing so, locked TCG OPAL enabled devices are unlocked
on resume, allowing normal operation.
Fixes: 3cc2ffe5c1 ("scsi: sd: Differentiate system and runtime start/stop management")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218538
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240319071209.1179257-1-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 321da3dc1f ]
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b09d7f8fd5 upstream.
It is not always possible to keep a device in the runtime suspended state
when a system level suspend/resume cycle is executed. E.g. for ATA devices
connected to AHCI adapters, system resume resets the ATA ports, which
causes connected devices to spin up. In such case, a runtime suspended disk
will incorrectly be seen with a suspended runtime state because the device
is not resumed by sd_resume_system(). The power state seen by the user is
different than the actual device physical power state.
Fix this issue by introducing the struct scsi_device flag
force_runtime_start_on_system_start. When set, this flag causes
sd_resume_system() to request a runtime resume operation for runtime
suspended devices. This results in the user seeing the device runtime_state
as active after a system resume, thus correctly reflecting the device
physical power state.
Fixes: 9131bff6a9 ("scsi: core: pm: Only runtime resume if necessary")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20231120225631.37938-3-dlemoal@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24eca2dce0 upstream.
Commit aa3998dbeb ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") change setting the manage_system_start_stop
flag to false for libata managed disks to enable libata internal
management of disk suspend/resume. However, a side effect of this change
is that on system shutdown, disks are no longer being stopped (set to
standby mode with the heads unloaded). While this is not a critical
issue, this unclean shutdown is not recommended and shows up with
increased smart counters (e.g. the unexpected power loss counter
"Unexpect_Power_Loss_Ct").
Instead of defining a shutdown driver method for all ATA adapter
drivers (not all of them define that operation), this patch resolves
this issue by further refining the sd driver start/stop control of disks
using the new flag manage_shutdown. If this new flag is set to true by
a low level driver, the function sd_shutdown() will issue a
START STOP UNIT command with the start argument set to 0 when a disk
needs to be powered off (suspended) on system power off, that is, when
system_state is equal to SYSTEM_POWER_OFF.
Similarly to the other manage_xxx flags, the new manage_shutdown flag is
exposed through sysfs as a read-write device attribute.
To avoid any confusion between manage_shutdown and
manage_system_start_stop, the comments describing these flags in
include/scsi/scsi.h are also improved.
Fixes: aa3998dbeb ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218038
Link: https://lore.kernel.org/all/cd397c88-bf53-4768-9ab8-9d107df9e613@gmail.com/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99398d2070 ]
If an error occurs when resuming a host adapter before the devices
attached to the adapter are resumed, the adapter low level driver may
remove the scsi host, resulting in a call to sd_remove() for the
disks of the host. This in turn results in a call to sd_shutdown() which
will issue a synchronize cache command and a start stop unit command to
spindown the disk. sd_shutdown() issues the commands only if the device
is not already runtime suspended but does not check the power state for
system-wide suspend/resume. That is, the commands may be issued with the
device in a suspended state, which causes PM resume to hang, forcing a
reset of the machine to recover.
Fix this by tracking the suspended state of a disk by introducing the
suspended boolean field in the scsi_disk structure. This flag is set to
true when the disk is suspended is sd_suspend_common() and resumed with
sd_resume(). When suspended is true, sd_shutdown() is not executed from
sd_remove().
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cc2ffe5c1 ]
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 99398d2070 ("scsi: sd: Do not issue commands to suspended disks on shutdown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a85890559 ]
During system resume, ata_port_pm_resume() triggers ata EH to
1) Resume the controller
2) Reset and rescan the ports
3) Revalidate devices
This EH execution is started asynchronously from ata_port_pm_resume(),
which means that when sd_resume() is executed, none or only part of the
above processing may have been executed. However, sd_resume() issues a
START STOP UNIT to wake up the drive from sleep mode. This command is
translated to ATA with ata_scsi_start_stop_xlat() and issued to the
device. However, depending on the state of execution of the EH process
and revalidation triggerred by ata_port_pm_resume(), two things may
happen:
1) The START STOP UNIT fails if it is received before the controller has
been reenabled at the beginning of the EH execution. This is visible
with error messages like:
ata10.00: device reported invalid CHS sector 0
sd 9:0:0:0: [sdc] Start/Stop Unit failed: Result: hostbyte=DID_OK driverbyte=DRIVER_OK
sd 9:0:0:0: [sdc] Sense Key : Illegal Request [current]
sd 9:0:0:0: [sdc] Add. Sense: Unaligned write command
sd 9:0:0:0: PM: dpm_run_callback(): scsi_bus_resume+0x0/0x90 returns -5
sd 9:0:0:0: PM: failed to resume async: error -5
2) The START STOP UNIT command is received while the EH process is
on-going, which mean that it is stopped and must wait for its
completion, at which point the command is rather useless as the drive
is already fully spun up already. This case results also in a
significant delay in sd_resume() which is observable by users as
the entire system resume completion is delayed.
Given that ATA devices will be woken up by libata activity on resume,
sd_resume() has no need to issue a START STOP UNIT command, which solves
the above mentioned problems. Do not issue this command by introducing
the new scsi_device flag no_start_on_resume and setting this flag to 1
in ata_scsi_dev_config(). sd_resume() is modified to issue a START STOP
UNIT command only if this flag is not set.
Reported-by: Paul Ausbeck <paula@soe.ucsc.edu>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215880
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Tanner Watkins <dalzot@gmail.com>
Tested-by: Paul Ausbeck <paula@soe.ucsc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Stable-dep-of: 99398d2070 ("scsi: sd: Do not issue commands to suspended disks on shutdown")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 288b3271d9 ]
When the sd driver revalidates host-managed SMR disks, it calls
disk_set_zoned() which changes the zone_write_granularity attribute value
to the logical block size regardless of the device type. After that, the sd
driver overwrites the value in sd_zbc_read_zone() with the physical block
size, since ZBC/ZAC requires this for host-managed disks. Between the calls
to disk_set_zoned() and sd_zbc_read_zone(), there exists a window where the
attribute shows the logical block size as the zone_write_granularity value,
which is wrong for host-managed disks. The duration of the window is from
20ms to 200ms, depending on report zone command execution time.
To avoid the wrong zone_write_granularity value between disk_set_zoned()
and sd_zbc_read_zone(), modify the value not in sd_zbc_read_zone() but
just after disk_set_zoned() call.
Fixes: a805a4fa4f ("block: introduce zone_write_granularity limit")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20230306063024.3376959-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Although commit 88f1669019 ("scsi: sd: Rework asynchronous resume support")
eliminates a delay for some ATA disks after resume, it causes resume of ATA
disks to fail on other setups. See also:
* "Resume process hangs for 5-6 seconds starting sometime in 5.16"
(https://bugzilla.kernel.org/show_bug.cgi?id=215880).
* Geert's regression report
(https://lore.kernel.org/linux-scsi/alpine.DEB.2.22.394.2207191125130.1006766@ramsan.of.borg/).
This is what I understand about this issue:
* During resume, ata_port_pm_resume() starts the SCSI error handler. This
changes the SCSI host state into SHOST_RECOVERY and causes
scsi_queue_rq() to return BLK_STS_RESOURCE.
* sd_resume() calls sd_start_stop_device() for ATA devices. That function
in turn calls sd_submit_start() which tries to submit a START STOP UNIT
command. That command can only be submitted after the SCSI error handler
has changed the SCSI host state back to SHOST_RUNNING.
* The SCSI error handler runs on its own thread and calls
schedule_work(&(ap->scsi_rescan_task)). That causes
ata_scsi_dev_rescan() to be called from the context of a kernel
workqueue. That call hangs in blk_mq_get_tag(). I'm not sure why - maybe
because all available tags have been allocated by sd_submit_start()
calls (this is a guess).
Link: https://lore.kernel.org/r/20220816172638.538734-1-bvanassche@acm.org
Fixes: 88f1669019 ("scsi: sd: Rework asynchronous resume support")
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: gzhqyz@gmail.com
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: gzhqyz@gmail.com
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: John Garry <john.garry@huawei.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- convert arm32 to the common dma-direct code (Arnd Bergmann, Robin Murphy,
Christoph Hellwig)
- restructure the PCIe peer to peer mapping support (Logan Gunthorpe)
- allow the IOMMU code to communicate an optional DMA mapping length
and use that in scsi and libata (John Garry)
- split the global swiotlb lock (Tianyu Lan)
- various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang,
Lukas Bulwahn, Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=Bv19
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- convert arm32 to the common dma-direct code (Arnd Bergmann, Robin
Murphy, Christoph Hellwig)
- restructure the PCIe peer to peer mapping support (Logan Gunthorpe)
- allow the IOMMU code to communicate an optional DMA mapping length
and use that in scsi and libata (John Garry)
- split the global swiotlb lock (Tianyu Lan)
- various fixes and cleanup (Chao Gao, Dan Carpenter, Dongli Zhang,
Lukas Bulwahn, Robin Murphy)
* tag 'dma-mapping-5.20-2022-08-06' of git://git.infradead.org/users/hch/dma-mapping: (45 commits)
swiotlb: fix passing local variable to debugfs_create_ulong()
dma-mapping: reformat comment to suppress htmldoc warning
PCI/P2PDMA: Remove pci_p2pdma_[un]map_sg()
RDMA/rw: drop pci_p2pdma_[un]map_sg()
RDMA/core: introduce ib_dma_pci_p2p_dma_supported()
nvme-pci: convert to using dma_map_sgtable()
nvme-pci: check DMA ops when indicating support for PCI P2PDMA
iommu/dma: support PCI P2PDMA pages in dma-iommu map_sg
iommu: Explicitly skip bus address marked segments in __iommu_map_sg()
dma-mapping: add flags to dma_map_ops to indicate PCI P2PDMA support
dma-direct: support PCI P2PDMA pages in dma-direct map_sg
dma-mapping: allow EREMOTEIO return code for P2PDMA transfers
PCI/P2PDMA: Introduce helpers for dma_map_sg implementations
PCI/P2PDMA: Attempt to set map_type if it has not been set
lib/scatterlist: add flag for indicating P2PDMA segments in an SGL
swiotlb: clean up some coding style and minor issues
dma-mapping: update comment after dmabounce removal
scsi: sd: Add a comment about limiting max_sectors to shost optimal limit
ata: libata-scsi: cap ata_device->max_sectors according to shost->max_sectors
scsi: scsi_transport_sas: cap shost opt_sectors according to DMA optimal limit
...
Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr). The main driver change that might cause issues on down the
road is the conversion of some of our oldest surviving drivers to the
DMA API (should only affect m68k). The only major core change is the
rework of async resume; the rest are either completely trivial or for
updating deprecated APIs.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYuvakyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfvOAP4m0N6b
e3JwoBtB1c0JMKv6G4gka8suEG8p5f4khDu8wwD+LfGUCzG49Y5Ts7rByXfEiGgO
krSdwsAZiV6yKg/HuPw=
=Ak9L
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
mpi3mr).
The main driver change that might cause issues on down the road is the
conversion of some of our oldest surviving drivers to the DMA API
(should only affect m68k).
The only major core change is the rework of async resume; the rest are
either completely trivial or for updating deprecated APIs"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (195 commits)
scsi: target: Remove XDWRITEREAD emulated support
scsi: megaraid: Remove the static variable initialisation
scsi: ch: Do not initialise statics to 0
scsi: ufs: core: Fix spelling mistake "Cannnot" -> "Cannot"
scsi: target: iscsi: Do not require target authentication
scsi: target: iscsi: Allow AuthMethod=None
scsi: target: iscsi: Support base64 in CHAP
scsi: target: iscsi: Add support for extended CDB AHS
scsi: ufs: dt-bindings: Add SC8280XP binding
scsi: target: iscsi: Fix clang -Wformat warnings
scsi: ufs: core: Read device property for ref clock
scsi: libsas: Resume SAS host for phy reset or enable via sysfs
scsi: hisi_sas: Modify v3 HW SATA completion error processing
scsi: hisi_sas: Relocate DMA unmap of SMP task
scsi: hisi_sas: Remove unnecessary variable to hold DMA map elements
scsi: hisi_sas: Call hisi_sas_slave_configure() from slave_configure_v3_hw()
scsi: mpi3mr: Delete a stray tab
scsi: mpi3mr: Unlock on error path
scsi: mpi3mr: Reduce VD queue depth on detecting throttling
scsi: mpi3mr: Resource Based Metering
...
Add a comment about limiting the default the SCSI disk request_queue
max_sectors initial value to that of the SCSI host optimal sectors limit.
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Streaming DMA mappings may be considerably slower when mappings go through
an IOMMU and the total mapping length is somewhat long. This is because the
IOMMU IOVA code allocates and free an IOVA for each mapping, which may
affect performance.
New member Scsi_Host.opt_sectors is added, which is the optimal host
max_sectors, and use this value to cap the request queue max_sectors when
set.
It could be considered to have request queues io_opt value initially
set at Scsi_Host.opt_sectors in __scsi_init_queue(), but that is not
really the purpose of io_opt.
Finally, even though Scsi_Host.opt_sectors value should never be greater
than the request queue max_hw_sectors value, continue to limit to this
value for safety.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For some technologies, e.g. an ATA bus, resuming can take multiple
seconds. Waiting for resume to finish can cause a very noticeable delay.
Hence this commit that restores the behavior from before "scsi: core: pm:
Rely on the device driver core for async power management" for most SCSI
devices.
This commit introduces a behavior change: if the START command fails, do
not consider this as a SCSI disk resume failure.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215880
Link: https://lore.kernel.org/r/20220630195703.10155-3-bvanassche@acm.org
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: ericspero@icloud.com
Cc: jason600.groome@gmail.com
Tested-by: jason600.groome@gmail.com
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prepare for storing the zone related field in struct gendisk instead
of struct request_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set the queue dying flag and call blk_mq_exit_queue from del_gendisk for
all disks that do not have separately allocated queues, and thus remove
the need to call blk_cleanup_queue for them.
Rename blk_cleanup_disk to blk_mq_destroy_queue to make it clear that
this function is intended only for separately allocated blk-mq queues.
This saves an extra queue freeze for devices without a separately
allocated queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20220619060552.1850436-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixing the interpretation of the length of the B9h VPD page (Concurrent
Positioning Ranges). Adding 4 is necessary as the first 4 bytes of the page
is the header with page number and length information. Adding 3 was likely
a misinterpretation of the SBC-5 specification which sets all offsets
starting at zero.
This fixes the error in dmesg:
[ 9.014456] sd 1:0:0:0: [sda] Invalid Concurrent Positioning Ranges VPD page
Link: https://lore.kernel.org/r/20220602225113.10218-4-tyler.erickson@seagate.com
Fixes: e815d36548 ("scsi: sd: add concurrent positioning ranges support")
Cc: stable@vger.kernel.org
Tested-by: Michael English <michael.english@seagate.com>
Reviewed-by: Muhammad Ahmad <muhammad.ahmad@seagate.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tyler Erickson <tyler.erickson@seagate.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mostly small bug fixes plus other trivial updates. The major change
of note is moving ufs out of scsi and a minor update to lpfc vmid
handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYptvayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishb1rAPwJWSl1
kB9Qt1xPa1JK0Z7To2LRkrQ4uxYbAnpTLEP6UgEA3YuBccXRppcYQe5CXCrcZryz
BtTbtI3ApiV40xC/SRk=
=Uit3
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes plus other trivial updates.
The major change of note is moving ufs out of scsi and a minor update
to lpfc vmid handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: qla2xxx: Remove unused 'ql_dm_tgt_ex_pct' parameter
scsi: qla2xxx: Remove setting of 'req' and 'rsp' parameters
scsi: mpi3mr: Fix kernel-doc
scsi: lpfc: Add support for ATTO Fibre Channel devices
scsi: core: Return BLK_STS_TRANSPORT for ALUA transitioning
scsi: sd_zbc: Prevent zone information memory leak
scsi: sd: Fix potential NULL pointer dereference
scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
scsi: myrb: Fix up null pointer access on myrb_cleanup()
scsi: core: Unexport scsi_bus_type
scsi: sd: Don't call blk_cleanup_disk() in sd_probe()
scsi: ufs: ufshcd: Delete unnecessary NULL check
scsi: isci: Fix typo in comment
scsi: pmcraid: Fix typo in comment
scsi: smartpqi: Fix typo in comment
scsi: qedf: Fix typo in comment
scsi: esas2r: Fix typo in comment
scsi: storvsc: Fix typo in comment
scsi: ufs: Split the drivers/scsi/ufs directory
scsi: qla1280: Remove redundant variable
...
Make sure to always free a scsi disk zone information, even for regular
disks. This ensures that there is no memory leak, even in the case of a
zoned disk changing type to a regular disk (e.g. with a reformat using the
FORMAT WITH PRESET command or other vendor proprietary command).
To do this, rename sd_zbc_clear_zone_info() to sd_zbc_free_zone_info() and
remove sd_zbc_release_disk(). A call to sd_zbc_free_zone_info() is added to
sd_zbc_read_zones() for drives for which sd_is_zoned() returns
false. Furthermore, sd_zbc_free_zone_info() code make s sure that the sdkp
rev_mutex is never used while not being initialized by gating the cleanup
code with a a check on the zone_wp_update_buf field as it is never NULL
when rev_mutex has been initialized.
Link: https://lore.kernel.org/r/20220601062544.905141-3-damien.lemoal@opensource.wdc.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If sd_probe() sees an early error before sdkp->device is initialized,
sd_zbc_release_disk() is called. This causes a NULL pointer dereference
when sd_is_zoned() is called inside that function. Avoid this by removing
the call to sd_zbc_release_disk() in sd_probe() error path.
This change is safe and does not result in zone information memory leakage
because the zone information for a zoned disk is allocated only when
sd_revalidate_disk() is called, at which point sdkp->disk_dev is fully set,
resulting in sd_disk_release() being called when needed to cleanup a disk
zone information using sd_zbc_release_disk().
Link: https://lore.kernel.org/r/20220601062544.905141-2-damien.lemoal@opensource.wdc.com
Fixes: 89d9475610 ("sd: Implement support for ZBC devices")
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of a small set of driver updates (lpfc, ufs,
mpt3sas mpi3mr, iscsi target). Apart from that this is mostly small
fixes with very few core changes (the biggest one being VPD caching.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYo2WnyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfEiAP4zvniL
xidsiCXGQ4pWF4QW3UxukXpGh5xFREhNCYT9+QEA+DyilCALOI+ZT5GKu2V6gkby
R29ve48/NAWl3fwYjMQ=
=GPL1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of a small set of driver updates (lpfc, ufs, mpt3sas
mpi3mr, iscsi target). Apart from that this is mostly small fixes with
very few core changes (the biggest one being VPD caching)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (177 commits)
scsi: target: tcmu: Avoid holding XArray lock when calling lock_page
scsi: elx: efct: Remove NULL check after calling container_of()
scsi: dpt_i2o: Drop redundant spinlock initialization
scsi: qedf: Remove redundant variable op
scsi: hisi_sas: Fix memory ordering in hisi_sas_task_deliver()
scsi: fnic: Replace DMA mask of 64 bits with 47 bits
scsi: mpi3mr: Add target device related sysfs attributes
scsi: mpi3mr: Add shost related sysfs attributes
scsi: elx: efct: Remove redundant memset() statement
scsi: megaraid_sas: Remove redundant memset() statement
scsi: mpi3mr: Return error if dma_alloc_coherent() fails
scsi: hisi_sas: Fix rescan after deleting a disk
scsi: hisi_sas: Use sas_ata_wait_after_reset() in IT nexus reset
scsi: libsas: Refactor sas_ata_hard_reset()
scsi: mpt3sas: Update driver version to 42.100.00.00
scsi: mpt3sas: Fix junk chars displayed while printing ChipName
scsi: ipr: Use kobj_to_dev()
scsi: mpi3mr: Fix a NULL vs IS_ERR() bug in mpi3mr_bsg_init()
scsi: bnx2fc: Avoid using get_cpu() in bnx2fc_cmd_alloc()
scsi: libfc: Remove get_cpu() semantics in fc_exch_em_alloc()
...
In SCSI the midlayer has ownership of the request_queue, so on probe
failure we must only put the gendisk, but leave the request_queue alone.
Link: https://lore.kernel.org/r/20220523083813.227935-1-hch@lst.de
Fixes: 03252259e1 ("scsi: sd: Clean up gendisk if device_add_disk() failed")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During device discovery we ended up calling revalidate twice and thus
requested the same parameters multiple times. This was originally necessary
due to the request_queue and gendisk needing to be instantiated to
configure the block integrity profile.
Since this dependency no longer exists, reorganize the integrity probing
code so it can be run once at the end of discovery and drop the superfluous
revalidate call. Postponing the registration step involves splitting
sd_read_protection() into two functions, one to read the device protection
type and one to configure the mode of operation.
As part of this cleanup, make the printing code a bit less verbose.
Link: https://lore.kernel.org/r/20220302053559.32147-14-martin.petersen@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit a83da8a450 ("scsi: sd: Optimal I/O size should be a multiple of
physical block size") validated the reported optimal I/O size against the
physical block size to overcome problems with devices reporting nonsensical
transfer sizes.
However, some devices claim conformity to older SCSI versions that predate
the physical block size being reported. Other devices do not report a
physical block size at all. We need to be able to validate the optimal I/O
size on those devices as well.
Many devices report an OPTIMAL TRANSFER LENGTH GRANULARITY in the same VPD
page as the OPTIMAL TRANSFER LENGTH. Use this value to validate the optimal
I/O size. Also check that the reported granularity is a multiple of the
physical block size, if supported.
Link: https://lore.kernel.org/r/33fb522e-4f61-1b76-914f-c9e6a3553c9b@gmail.com
Link: https://lore.kernel.org/r/20220302053559.32147-9-martin.petersen@oracle.com
Reported-by: Bernhard Sulzer <micraft.b@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the VPD pages already provided by the SCSI midlayer. No need to request
them individually in the SCSI disk driver.
Link: https://lore.kernel.org/r/20220302053559.32147-8-martin.petersen@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the ATA Information VPD is now cached at device discovery time it is
no longer necessary to request this page when we configure WRITE SAME.
Instead use the cached information to determine if this disk sits behind a
SCSI-ATA translation layer.
Link: https://lore.kernel.org/r/20220302053559.32147-7-martin.petersen@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just use a non-zero max_discard_sectors as an indicator for discard
support, similar to what is done for write zeroes.
The only places where needs special attention is the RAID5 driver,
which must clear discard support for security reasons by default,
even if the default stacking rules would allow for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> [drbd]
Acked-by: Jan Höppner <hoeppner@linux.ibm.com> [s390]
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220415045258.199825-25-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As such it should be called inside the scsi_device_supports_vpd()
conditional.
Link: https://lore.kernel.org/r/20220302053559.32147-13-martin.petersen@oracle.com
Fixes: e815d36548 ("scsi: sd: add concurrent positioning ranges support")
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes. The high blast radius core update is the removal of
write same, which affects block and several non-SCSI devices. The
other big change, which is more local, is the removal of the SCSI
pointer.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYjzDQyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMYAQDEWUGV
6U0+736AHVtOfiMNfiRN79B1HfXVoHvemnPcTwD/UlndwFfy/3GGOtoZmqEpc73J
Ec1HDuUCE18H1H2QAh0=
=/Ty9
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes.
The high blast radius core update is the removal of write same, which
affects block and several non-SCSI devices. The other big change,
which is more local, is the removal of the SCSI pointer"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (281 commits)
scsi: scsi_ioctl: Drop needless assignment in sg_io()
scsi: bsg: Drop needless assignment in scsi_bsg_sg_io_fn()
scsi: lpfc: Copyright updates for 14.2.0.0 patches
scsi: lpfc: Update lpfc version to 14.2.0.0
scsi: lpfc: SLI path split: Refactor BSG paths
scsi: lpfc: SLI path split: Refactor Abort paths
scsi: lpfc: SLI path split: Refactor SCSI paths
scsi: lpfc: SLI path split: Refactor CT paths
scsi: lpfc: SLI path split: Refactor misc ELS paths
scsi: lpfc: SLI path split: Refactor VMID paths
scsi: lpfc: SLI path split: Refactor FDISC paths
scsi: lpfc: SLI path split: Refactor LS_RJT paths
scsi: lpfc: SLI path split: Refactor LS_ACC paths
scsi: lpfc: SLI path split: Refactor the RSCN/SCR/RDF/EDC/FARPR paths
scsi: lpfc: SLI path split: Refactor PLOGI/PRLI/ADISC/LOGO paths
scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path
scsi: lpfc: SLI path split: Introduce lpfc_prep_wqe
scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
scsi: lpfc: SLI path split: Refactor lpfc_iocbq
scsi: lpfc: Use kcalloc()
...
Implement the ->free_disk method to to put struct scsi_disk when the last
gendisk reference count goes away. This removes the need to clear
->private_data and thus freeze the queue on unbind.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Call free_opal_dev from scsi_disk_release as the opal_dev field is accessed
from the ioctl handler, which isn't synchronized vs sd_release and thus
can be accessed during or after sd_release was called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
sd_zbc_release_disk accesses disk->device, so ensure that actually still has
a valid reference.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
dev is very hard to grep for. Give the field a more descriptive name and
documents its purpose.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Requiring every ULP to have the scsi_drive as first member of the
private data is rather fragile and not necessary anyway. Just use
the driver hanging off the SCSI device instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220308055200.735835-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Kernel messages produced during runtime PM can cause a never-ending cycle
because user space utilities (e.g. journald or rsyslog) write the messages
back to storage, causing runtime resume, more messages, and so on.
Messages that tell of things that are expected to happen are arguably
unnecessary, so add a flag to suppress them. This flag is used by the UFS
driver.
Link: https://lore.kernel.org/r/20220228113652.970857-2-adrian.hunter@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that each scsi_request is backed by a scsi_cmnd, there is no need to
indirect the CDB storage. Change all submitters of SCSI passthrough
requests to store the CDB information directly in the scsi_cmnd, and while
doing so allocate the full 32 bytes that cover all Linux supported SCSI
hosts instead of requiring dynamic allocation for > 16 byte CDBs. On
64-bit systems this does not change the size of the scsi_cmnd at all, while
on 32-bit systems it slightly increases it for now, but that increase will
be made up by the removal of the remaining scsi_request fields.
Link: https://lore.kernel.org/r/20220224175552.988286-4-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are no more end-users of REQ_OP_WRITE_SAME left, so we can start
deleting it.
Link: https://lore.kernel.org/r/20220209082828.2629273-5-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no good reason to keep genhd.h separate from the main blkdev.h
header that includes it. So fold the contents of genhd.h into blkdev.h
and remove genhd.h entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220124093913.742411-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This series is all the stragglers that didn't quite make the first
merge window pull. It's mostly minor updates and bug fixes of merge
window code.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYetVgSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfElAQD/OZPx
dceTIXQixYGuHhGI3Il8O5ASYQVIU86gv+jRrgEA/MN4EWj4VsYaocrUdtTCBON1
wJYcC7VUekfNBX6KdeY=
=DcbH
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This series is all the stragglers that didn't quite make the first
merge window pull. It's mostly minor updates and bug fixes of merge
window code"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: nsp_cs: Check of ioremap return value
scsi: ufs: ufs-mediatek: Fix error checking in ufs_mtk_init_va09_pwr_ctrl()
scsi: ufs: Modify Tactive time setting conditions
scsi: efct: Remove useless DMA-32 fallback configuration
scsi: message: fusion: mptctl: Use dma_alloc_coherent()
scsi: message: fusion: mptsas: Use dma_alloc_coherent()
scsi: message: fusion: Use dma_alloc_coherent() in mptsas_exp_repmanufacture_info()
scsi: message: fusion: mptbase: Use dma_alloc_coherent()
scsi: message: fusion: Use dma_alloc_coherent() in mpt_alloc_fw_memory()
scsi: message: fusion: Remove usage of the deprecated "pci-dma-compat.h" API
scsi: megaraid: Avoid mismatched storage type sizes
scsi: hisi_sas: Remove unused variable and check in hisi_sas_send_ata_reset_each_phy()
scsi: aic79xx: Remove redundant error variable
scsi: pm80xx: Port reset timeout error handling correction
scsi: mpi3mr: Fix formatting problems in some kernel-doc comments
scsi: mpi3mr: Fix some spelling mistakes
scsi: mpt3sas: Update persistent trigger pages from sysfs interface
scsi: core: Fix scsi_mode_select() interface
scsi: aacraid: Fix spelling of "its"
scsi: qedf: Fix potential dereference of NULL pointer
This series consists of the usual driver updates (ufs, pm80xx, lpfc,
mpi3mr, mpt3sas, hisi_sas, libsas) and minor updates and bug fixes.
The most impactful change is likely the switch from GFP_DMA to
GFP_KERNEL in a bunch of drivers, but even that shouldn't affect too
many people.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYeCJZyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfMnAQCsERG9
V4yX8LDpBjD7leIccf+6krJNNWaIWYYkEdxpzQD9FShB7/yDakFq3erW2y5mVqac
dZ065M0ckE4bxk9uMIE=
=gPHF
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, pm80xx, lpfc,
mpi3mr, mpt3sas, hisi_sas, libsas) and minor updates and bug fixes.
The most impactful change is likely the switch from GFP_DMA to
GFP_KERNEL in a bunch of drivers, but even that shouldn't affect too
many people"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (121 commits)
scsi: mpi3mr: Bump driver version to 8.0.0.61.0
scsi: mpi3mr: Fixes around reply request queues
scsi: mpi3mr: Enhanced Task Management Support Reply handling
scsi: mpi3mr: Use TM response codes from MPI3 headers
scsi: mpi3mr: Add io_uring interface support in I/O-polled mode
scsi: mpi3mr: Print cable mngnt and temp threshold events
scsi: mpi3mr: Support Prepare for Reset event
scsi: mpi3mr: Add Event acknowledgment logic
scsi: mpi3mr: Gracefully handle online FW update operation
scsi: mpi3mr: Detect async reset that occurred in firmware
scsi: mpi3mr: Add IOC reinit function
scsi: mpi3mr: Handle offline FW activation in graceful manner
scsi: mpi3mr: Code refactor of IOC init - part2
scsi: mpi3mr: Code refactor of IOC init - part1
scsi: mpi3mr: Fault IOC when internal command gets timeout
scsi: mpi3mr: Display IOC firmware package version
scsi: mpi3mr: Handle unaligned PLL in unmap cmnds
scsi: mpi3mr: Increase internal cmnds timeout to 60s
scsi: mpi3mr: Do access status validation before adding devices
scsi: mpi3mr: Add support for PCIe Managed Switch SES device
...
The modepage argument is unused. Remove it.
Link: https://lore.kernel.org/r/20210929091744.706003-3-damien.lemoal@wdc.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove this include directive from code that does not use any functionality
from kernel/async.c.
Link: https://lore.kernel.org/r/20211129194609.3466071-13-bvanassche@acm.org
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that blk_execute_rq does not take a gendisk argument there is no need
to pass it through the scsi_ioctl callchain either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20211126121802.2090656-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just use the disk attached to the request_queue instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20211126121802.2090656-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All modern drivers can support extra partitions using the extended
dev_t. In fact except for the ioctl method drivers never even see
partitions in normal operation.
So remove the GENHD_FL_EXT_DEVT and allow extra partitions for all
block devices that do support partitions, and require those that
do not support partitions to explicit disallow them using
GENHD_FL_NO_PART.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211122130625.1136848-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
