This reverts commit d2c755e66617620b729041c625a6396c81d1231c
("drm: atmel-hlcdc: enable sys_clk during initalization."). With
commit "drm: atmel-hlcdc: enable clock before configuring timing engine"
there is no need for this patch. Code is also simpler.
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-7-git-send-email-claudiu.beznea@microchip.com
The intention was to only select a higher pixel-clock rate than the
requested, if a slight overclocking would result in a rate significantly
closer to the requested rate than if the conservative lower pixel-clock
rate is selected. The fixed patch has the logic the other way around and
actually prefers the higher frequency. Fix that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: 9946a3a9db ("drm/atmel-hlcdc: allow selecting a higher pixel-clock than requested")
Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: <stable@vger.kernel.org> # v4.20+
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-6-git-send-email-claudiu.beznea@microchip.com
Changing pixel clock source without having this clock source enabled
will block the timing engine and the next operations after (in this case
setting ATMEL_HLCDC_CFG(5) settings in atmel_hlcdc_crtc_mode_set_nofb()
will fail). It is recomended (although in datasheet this is not present)
to actually enabled pixel clock source before doing any changes on timing
enginge (only SAM9X60 datasheet specifies that the peripheral clock and
pixel clock must be enabled before using LCD controller).
Fixes: 1a396789f6 ("drm: add Atmel HLCDC Display Controller support")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # v4.0+
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-3-git-send-email-claudiu.beznea@microchip.com
Doubled system clock should be used as pixel cock source only if this
is supported. This is emphasized by the value of
atmel_hlcdc_crtc::dc::desc::fixed_clksrc.
Fixes: a6eca2abdd ("drm: atmel-hlcdc: add config option for clock selection")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-2-git-send-email-claudiu.beznea@microchip.com
Checking both is one too much, so wrap a WARN_ON around it to stope
the copypasta.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213172612.1514842-3-daniel.vetter@ffwll.ch
Spotted while looking through them all.
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20191115092120.4445-3-daniel.vetter@ffwll.ch
The drm panel bridge creates a connector using a connector type
explicitly passed by the display controller or bridge driver that
instantiates the panel bridge. Now that drm_panel reports its connector
type, we can use it to avoid passing an explicit (and often incorrect)
connector type to drm_panel_bridge_add() and
devm_drm_panel_bridge_add().
Several drivers report incorrect or unknown connector types to
userspace. Reporting a different type may result in a breakage. For that
reason, rename (devm_)drm_panel_bridge_add() to
(devm_)drm_panel_bridge_add_typed(), and add new
(devm_)drm_panel_bridge_add() functions that use the panel connector
type. Update all callers of (devm_)drm_panel_bridge_add() to the _typed
function, they will be converted one by one after testing.
The panel drivers have been updated with the following Coccinelle
semantic patch, with manual inspection and fixes to indentation.
@@
expression bridge;
expression dev;
expression panel;
identifier type;
@@
(
-bridge = drm_panel_bridge_add(panel, type);
+bridge = drm_panel_bridge_add_typed(panel, type);
|
-bridge = devm_drm_panel_bridge_add(dev, panel, type);
+bridge = devm_drm_panel_bridge_add_typed(dev, panel, type);
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904132804.29680-3-laurent.pinchart@ideasonboard.com
Drop use of the deprecated header drmP.h.
Make header file self-contained, with only the required set
of include files.
And fixed fallout in remaining files.
Divide include files in blocks and sort them within each block.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190630061922.7254-15-sam@ravnborg.org
This bit enables replication logic to expand an RGB color less than 24
bits, to 24 bits, which is used internally for all formats. Otherwise,
the least significant bits are always set to zero and the color may not
be what is expected.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1562686509-8747-1-git-send-email-joshua.henderson@microchip.com
They're the default.
Aside: Would be really nice to switch the others over to
drm_gem_object_funcs.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190614203615.12639-13-daniel.vetter@ffwll.ch
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SAM9X60 SoC, sys_clk is through lcd_gclk clock source and this
needs to be enabled before enabling lcd_clk.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[claudiu.beznea@microchip.com: add fixed_clksrc checks]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-5-git-send-email-claudiu.beznea@microchip.com
SAM9x60 LCD Controller has no option to select clock source as previous
controllers have. To be able to use the same driver even for this LCD
controller add a config option to know if controller supports this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1556195748-11106-2-git-send-email-claudiu.beznea@microchip.com
Cross-subsystem Changes:
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
-----BEGIN PGP SIGNATURE-----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=2K7c
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-05-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3, try #2:
UAPI Changes:
- Add HDR source metadata property.
- Make drm.h compile on GNU/kFreeBSD by including stdint.h
- Clarify how the userspace reviewer has to review new kernel UAPI.
- Clarify that for using new UAPI, merging to drm-next or drm-misc-next should be enough.
Cross-subsystem Changes:
- video/hdmi: Add unpack function for DRM infoframes.
- Device tree bindings:
* Updating a property for Mali Midgard GPUs
* Updating a property for STM32 DSI panel
* Adding support for FriendlyELEC HD702E 800x1280 panel
* Adding support for Evervision VGG804821 800x480 5.0" WVGA TFT panel
* Adding support for the EDT ET035012DM6 3.5" 320x240 QVGA 24-bit RGB TFT.
* Adding support for Three Five displays TFC S9700RTWV43TR-01B 800x480 panel
with resistive touch found on TI's AM335X-EVM.
* Adding support for EDT ETM0430G0DH6 480x272 panel.
- Add OSD101T2587-53TS driver with DT bindings.
- Add Samsung S6E63M0 panel driver with DT bindings.
- Add VXT VL050-8048NT-C01 800x480 panel with DT bindings.
- Dma-buf:
- Make mmap callback actually optional.
- Documentation updates.
- Fix debugfs refcount inbalance.
- Remove unused sync_dump function.
- Fix device tree bindings in drm-misc-next after a botched merge.
Core Changes:
- Add support for HDR infoframes and related EDID parsing.
- Remove prime sg_table caching, now done inside dma-buf.
- Add shiny new drm_gem_vram helpers for simple VRAM drivers;
with some fixes to the new API on top.
- Small fix to job cleanup without timeout handler.
- Documentation fixes to drm_fourcc.
- Replace lookups of drm_format with struct drm_format_info;
remove functions that become obsolete by this conversion.
- Remove double include in bridge/panel.c and some drivers.
- Remove drmP.h include from drm/edid and drm/dp.
- Fix null pointer deref in drm_fb_helper_hotplug_event().
- Remove most members from drm_fb_helper_crtc, only mode_set is kept.
- Remove race of fb helpers with userspace; only restore mode
when userspace is not master.
- Move legacy setup from drm_file.c to drm_legacy_misc.c
- Rework scheduler job destruction.
- drm/bus was removed, remove from TODO.
- Add __drm_atomic_helper_crtc_reset() to subclass crtc_state,
and convert some drivers to use it (conversion is not complete yet).
- Bump vblank timeout wait to 100 ms for atomic.
- Docbook fix for drm_hdmi_infoframe_set_hdr_metadata.
Driver Changes:
- sun4i: Use DRM_GEM_CMA_VMAP_DRIVER_OPS instead of definining manually.
- v3d: Small cleanups, adding support for compute shaders,
reservation/synchronization fixes and job management refactoring,
fixes MMU and debugfs.
- lima: Fix null pointer in irq handler on startup, set default timeout for scheduled jobs.
- stm/ltdc: Assorted fixes and adding FB modifier support.
- amdgpu: Avoid hw reset if guilty job was already signaled.
- virtio: Add seqno to fences, add trace events, use correct flags for fence allocation.
- Convert AST, bochs, mgag200, vboxvideo, hisilicon to the new drm_gem_vram API.
- sun6i_mipi_dsi: Support DSI GENERIC_SHORT_WRITE_2 transfers.
- bochs: Small fix to use PTR_RET_OR_ZERO and driver unload.
- gma500: header fixes
- cirrus: Remove unused files.
- mediatek: Fix compiler warning after merging the HDR series.
- vc4: Rework binner bo handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/052875a5-27ba-3832-60c2-193d950afdff@linux.intel.com
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_format_horz_chroma_subsampling and drm_format_vert_chroma_subsampling
are basically a lookup in the drm_format_info table plus an access to the
hsub and vsub fields of the appropriate entry.
Most drivers are using this function while having access to the entry
already, which means that we will perform an unnecessary lookup. Removing
the call to these functions is therefore more efficient.
Some drivers will not have access to that entry in the function, but in
this case the overhead is minimal (we just have to call drm_format_info()
to perform the lookup) and we can even avoid multiple, inefficient lookups
in some places that need multiple fields from the drm_format_info
structure.
This is amplified by the fact that most of the time the callers will have
to retrieve both the vsub and hsub fields, meaning that they would perform
twice the lookup.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6b3cceb8161e2c1d40c2681de99202328b0a8abc.1558002671.git-series.maxime.ripard@bootlin.com
With the help from drm_atomic_helper_check_plane_state function, clipping
now handles planes to be partially or totally off-screen. The plane is
disabled if it is not visible.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190110151020.30468-4-peda@axentia.se
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-7-noralf@tronnes.org
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <contact@tzimmermann.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180701132415.10161-1-contact@tzimmermann.org
This beats the heuristic that the connector is involved in what format
should be output for cases where this fails.
E.g. if there is a bridge that changes format between the encoder and the
connector, or if some of the RGB pins between the lcd controller and the
encoder are not routed on the PCB.
This is critical for the devices that have the "conflicting output
formats" issue (SAM9N12, SAM9X5, SAMA5D3), since the most significant
RGB bits move around depending on the selected output mode. For
devices that do not have the "conflicting output formats" issue
(SAMA5D2, SAMA5D4), this is completely irrelevant.
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180825085620.10566-5-peda@axentia.se
This enables more flexible devicetrees. You can e.g. have two output
nodes where one is not enabled, without the ordering affecting things.
Prior to this patch the active nodes had to have endpoint id zero and
upwards consecutively.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180825085620.10566-4-peda@axentia.se
But only if the highest pixel-clock frequency lower than requested
is significantly less accurate than the lowest frequency higher than
requested.
I pulled "10 times" as the discriminator out of the hat, and went with
that.
This is useful, if e.g. the target pixel-clock is 65MHz and the sys_clk
is 132MHz. In this case the highest possible pixel-clock lower than the
requested 65MHz is 52.8MHz, which is almost 20% off (and outside the
spec for the panel). The lowest possible pixel-clock higher than 65MHz
is 66MHz, which is a *much* better match, and only 1.5% off.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824092458.13165-3-peda@axentia.se
If the divider used to get the pixel-clock is small, the granularity
of the frequencies possible for the pixel-clock is quite coarse. E.g.
requesting a pixel-clock of 65MHz with a sys_clk of 132MHz results
in the divider being set to 3 ending up with 44MHz.
By preferring the doubled sys_clk as base, the divider instead ends
up as 5 yielding a pixel-clock of 52.8Mhz, which is a definite
improvement.
While at it, clamp the divider so that it does not overflow in case
it gets big.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824092458.13165-2-peda@axentia.se
A new helper function(__drm_atomic_helper_plane_reset) has been added
for linking a plane with its state and resetting the core
properties(alpha, rotation, etc.) to their default values.
Use that instead of duplicating the logic.
__drm_atomic_helper_plane_reset initializes the alpha property to its
max value, which is defined by the drm core as DRM_BLEND_ALPHA_OPAQUE,
so nothing changes regarding the alpha value.
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180804161530.12275-5-alexandru-cosmin.gheorghe@arm.com
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
-----BEGIN PGP SIGNATURE-----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=ngPr
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
The statement always evaluates to true since the struct fields
are arrays. This has shown up as a warning when compiling with
clang:
warning: address of array 'desc->layout.xstride' will always
evaluate to 'true' [-Wpointer-bool-conversion]
Check for values in the first plane instead.
Fixes: 1a396789f6 ("drm: add Atmel HLCDC Display Controller support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180617084826.31885-1-stefan@agner.ch
We want to get rid of plane->fb on atomic drivers. Stop looking at it.
Daniel pointed out that the drm_framebuffer_put() in the plane cleanup
indicates that the driver doesn't shut things down cleanly. To do
that we should be able to just call drm_atomic_helper_shutdown(). Not
really sure the current cleanup sequence is actually sane, but whatever.
v2: Replace the drm_framebuffer_put() with
drm_atomic_helper_shutdown() (Daniel)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405151400.11326-10-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-6-noralf@tronnes.org
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's dead code because this is now handled in the core.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Engestrom <eric@engestrom.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-5-daniel.vetter@ffwll.ch
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
drm_*_reference() and drm_*_unreference() functions are just
compatibility alias for drm_*_get() and drm_*_put() and should not be
used by new code. So convert all users of compatibility functions to use
the new APIs.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501761585-11757-6-git-send-email-cakturk@gmail.com
