In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes: 91725d89b9 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.
The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.
Fixes: 55fd0cf320 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it has always been possible to infer that an HWRM command was
abandoned due to an unhealthy firmware status by the shortened timeout
reported, this change improves the log messaging to account for this
case explicitly. In the interests of further clarity, the firmware
status is now also reported in these new messages.
v2: Remove inline keyword for hwrm_wait_must_abort() in .c file.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 881d8353b0 ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current driver design relies on the PF netdev being open in order
to intercept the following HWRM commands from a VF:
- HWRM_FUNC_VF_CFG
- HWRM_CFA_L2_FILTER_ALLOC
- HWRM_PORT_PHY_QCFG (only if FW_CAP_LINK_ADMIN is not supported)
If the PF is closed, then VFs are subjected to rather inscrutable error
messages in response to any configuration requests involving the above
command types. Recent firmware distinguishes this problem case from
other errors by returning HWRM_ERR_CODE_PF_UNAVAILABLE. In most cases,
the appropriate course of action is still to fail, but this can now be
accomplished with the aid of more user informative log messages. For L2
filter allocations that are already asynchronous, an automatic retry
seems more appropriate.
v2: Delete extra newline.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add logging of firmware messages. These can be useful for diagnosing
issues in the field, but due to their verbosity are only appropriate
at a debug message level.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If NETIF_F_GRO_HW is disabled, the existing driver code uses kmalloc'ed
data for RX buffers. This causes inefficient SW GRO performance
because the GRO data is merged using the less efficient frag_list.
Use netdev_alloc_frag() and friends instead so that GRO data can be
merged into skb_shinfo(skb)->frags for better performance.
[Use skb_free_frag() - Vikas Gupta]
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xdp_do_flush_map function has been replaced with the more general
xdp_do_flush().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CQE coalescing mode is the same as the timer reset coalescing mode
on Broadcom devices. Currently this mode is always enabled if it
is supported by the device. Restructure the code slightly to support
dynamically changing this mode.
Add a flags field to struct bnxt_coal. Initially, the CQE flag will
be set for the RX and TX side if the device supports it. We need to
move bnxt_init_dflt_coal() to set up default coalescing until the
capability is determined.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5750X (P5) chips handle receiving packets on the NQ rather than the main
completion queue so we need to get and set stats from the correct spots
for dynamic interrupt moderation.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log the unrecognized error report type value as well.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW has been modified to send a new async event when it detects
a pause storm. Register for this new event and log it upon receipt.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
include/linux/netdevice.h became too big, move gro stuff
into include/net/gro.h
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Live patches are activated by using the 'limit no_reset' option when
performing a devlink dev reload fw_activate operation. These packages
must first be installed on the device in the usual way. For example,
via devlink dev flash or ethtool -f.
The devlink device info has also been enhanced to render stored and
running live patch versions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes are firmware live patch support and 2 additional FEC
standard counters.
Add the matching FEC counters to ethtool counter array. Firmware older
than 220 does not return the proper size of the extended RX counters so
we need to cap it at the smaller legacy size. Otherwise the new FEC
counters may show up with garbage values.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware provides coredump and crashdump size info via
DBG_QCFG command. Read the dump sizes from firmware, instead of
computing in the driver. This patch reduces the time taken
to collect the dump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware event counters as well as health state severity. In
the unhealthy state, recommend a remedy and inform the user as to
its impact.
Readability of the devlink tool's output is negatively impacted by
adding these fields to the diagnosis. The single line of text, as
rendered by devlink health diagnose, benefits from more terse
descriptions, which can be substituted without loss of clarity, even
in pretty printed JSON mode.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware resets initiated by the user are not errors and should not
be reported via devlink. Once only unsolicited resets remain, it is no
longer sensible to maintain a separate fw_reset reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recovery election messages are often mistaken for errors. Improve
the wording to clarify the meaning of these frequent and expected
events. Also, take the first step towards more inclusive language.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reported parameter value should not take into account the state
of remote drivers. Firmware will reject remote resets as appropriate,
thus it is not strictly necessary to check HOT_RESET_ALLOWED before
attempting to initiate a reset. But we add the check so that we can
provide more intuitive messages when reset is not permitted.
This firmware setting needs to be restored from all functions after
a firmware reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to reload driver_reinit, the RTNL lock is held across reload
down and up to prevent interleaving state changes. But we need to
subsequently release the RTNL lock while waiting for firmware reset
to complete.
Also keep a statistic on fw_activate resets initiated remotely from
other functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTNL lock must be held between down and up to prevent interleaving
state changes, especially since external state changes might release
and allocate different driver resource subsets that would otherwise
need to be tracked and carefully handled. If the down function fails,
then devlink will not call the corresponding up function, thus the
lock is released in the down error paths.
v2: Don't use devlink_reload_disable() and devlink_reload_enable().
Instead, check that the netdev is not in unregistered state before
proceeding with reload.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-Off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource reservations will also need to be reset after FUNC_DRV_UNRGTR
in the following devlink driver_reinit patch. Extract this logic into a
reusable function.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device info logged during probe will be reused by the devlink
driver_reinit code in a following patch. Extract this logic into
the new bnxt_print_device_info() function. The board index needs
to be saved in the driver context so that the board information
can be retrieved at a later time, outside of the probe function.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The open code which is dev->priv_flags & IFF_RXFH_CONFIGURED is defined as
a helper function on netdevice.h. So use netif_is_rxfh_configured()
function instead of open code. This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink is a software interface that doesn't depend on any hardware
capabilities. The failure in SW means memory issues, wrong parameters,
programmer error e.t.c.
Like any other such interface in the kernel, the returned status of
devlink APIs should be checked and propagated further and not ignored.
Fixes: 4ab0c6a8ff ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently changed the completion ring page arrays to be dynamically
allocated to better support the expanded range of ring depths. The
cleanup path for this was not quite complete. It might cause the
shutdown path to crash if we need to abort before the completion ring
arrays have been allocated and initialized.
Fix it by initializing the ring_mem->pg_arr to NULL after freeing the
completion ring page array. Add a check in bnxt_free_ring() to skip
referencing the rmem->pg_arr if it is NULL.
Fixes: 03c7448790 ("bnxt_en: Don't use static arrays for completion ring pages")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b918319 ("bnxt_en: Fix possible unintended driver initiated error recovery")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter. If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter. If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed. This will
trigger error recovery unintentionally.
The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check. But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.
Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state. Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.
Fixes: 7e914027f7 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic assumes that when the driver sends the message to the
firmware to add the VXLAN or Geneve port, the firmware will never fail
the operation. The UDP ports are always stored and are used to check
the tunnel packets in .ndo_features_check(). These tunnnel packets
will fail to offload on the transmit side if firmware fails the call to
add the UDP ports.
To fix the problem, bp->vxlan_port and bp->nge_port will only be set to
the offloaded ports when the HWRM_TUNNEL_DST_PORT_ALLOC firmware call
succeeds. When deleting a UDP port, we check that the port was
previously added successfuly first by checking the FW ID.
Fixes: 1698d600b3 ("bnxt_en: Implement .ndo_features_check().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver requires 64-bit doorbell writes to be atomic on 32-bit
architectures. So we redefined writeq as a new macro with spinlock
protection on 32-bit architectures. This created a new warning when
we added a new file in a recent patchset. writeq is defined on many
32-bit architectures to do the memory write non-atomically and it
generated a new macro redefined warning. This warning was fixed
incorrectly in the recent patch.
Fix this properly by adding a new bnxt_writeq() function that will
do the non-atomic write under spinlock on 32-bit systems. All callers
in the driver will now call bnxt_writeq() instead.
v2: Need to pass in bp to bnxt_writeq()
Use lo_hi_writeq() [suggested by Florian]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: f9ff578251 ("bnxt_en: introduce new firmware message API based on DMA pools")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure to maintain a pending list of HWRM commands awaiting
completion and reduce the scope of the hwrm_cmd_lock mutex so that it
protects only the request mailbox. The mailbox is free to use for one
or more concurrent commands after receiving deferred response events.
For uniformity and completeness, use the same pending list for
collecting completions for commands that respond via a completion ring.
These commands are only used for freeing rings and for IRQ test and
we only support one such command in flight.
Note deferred responses are also only supported on the main channel.
The secondary channel (KONG) does not support deferred responses.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no longer any callers relying on the old API.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion follows this general pattern for most of the calls:
1. The input message is changed from a stack variable initialized
using bnxt_hwrm_cmd_hdr_init() to a pointer allocated and intialized
using hwrm_req_init().
2. If we don't need to read the firmware response, the hwrm_send_message()
call is replaced with hwrm_req_send().
3. If we need to read the firmware response, the mutex lock is replaced
by hwrm_req_hold() to hold the response. When the response is read, the
mutex unlock is replaced by hwrm_req_drop().
If additional DMA buffers are needed for firmware response data, the
hwrm_req_dma_slice() is used instead of calling dma_alloc_coherent().
Some minor refactoring is also done while doing these conversions.
v2: Fix unintialized variable warnings in __bnxt_hwrm_get_tx_rings()
and bnxt_approve_mac()
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use the hwrm_cmd_lock to serialize the update of the
firmware's link status response data and the copying of link status data
to the VF. This won't work when we update the firmware message APIs, so
we use the link_lock mutex instead. All link_info data should be
updated under the link_lock mutex. Also add link_lock to functions that
touch link_info in __bnxt_open_nic() and bnxt_probe_phy(). The locking
is probably not strictly necessary during probe, but it's more consistent.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change constitutes a major step towards supporting multiple
firmware commands in flight by maintaining a separate response buffer
for the duration of each request. These firmware commands are also
known as Hardware Resource Manager (HWRM) commands. Using separate
response buffers requires an API change in order for callers to be
able to free the buffer when done.
It is impossible to keep the existing APIs unchanged. The existing
usage for a simple HWRM message request such as the following:
struct input req = {0};
bnxt_hwrm_cmd_hdr_init(bp, &req, REQ_TYPE, -1, -1);
rc = hwrm_send_message(bp, &req, sizeof(req), HWRM_CMD_TIMEOUT);
if (rc)
/* error */
changes to:
struct input *req;
rc = hwrm_req_init(bp, req, REQ_TYPE);
if (rc)
/* error */
rc = hwrm_req_send(bp, req); /* consumes req */
if (rc)
/* error */
The key changes are:
1. The req is no longer allocated on the stack.
2. The caller must call hwrm_req_init() to allocate a req buffer and
check for a valid buffer.
3. The req buffer is automatically released when hwrm_req_send() returns.
4. If the caller wants to check the firmware response, the caller must
call hwrm_req_hold() to take ownership of the response buffer and
release it afterwards using hwrm_req_drop(). The caller is no longer
required to explicitly hold the hwrm_cmd_lock mutex to read the
response.
5. Because the firmware commands and responses all have different sizes,
some safeguards are added to the code.
This patch maintains legacy API compatibiltiy, implementing the old
API in terms of the new. The follow-on patches will convert all
callers to use the new APIs.
v2: Fix redefined writeq with parisc .config
Fix "cast from pointer to integer of different size" warning in
hwrm_calc_sentinel()
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all firmware messaging functions and definitions to new
bnxt_hwrm.[ch]. The follow-on patches will make major modifications
to these APIs.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code so that __bnxt_hwrm_ver_get() does not call
bnxt_hwrm_do_send_msg() directly. The new APIs will not expose this
internal call. Add a new bnxt_hwrm_poll() to poll the HWRM_VER_GET
firmware call silently. The other bnxt_hwrm_ver_get() function will
send the HWRM_VER_GET message directly with error logs enabled.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The additional response buffer serves no useful purpose. There can
be only one firmware command in flight due to the hwrm_cmd_lock mutex,
which is taken for the entire duration of any command completion,
KONG or otherwise. It is thus safe to share a single DMA buffer.
Removing the code associated with the additional mapping will simplify
matters in the next patch, which allocates response buffers from DMA
pools on a per request basis.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count packets dropped due to buffer or skb allocation errors.
Report as part of rx_dropped.
v2: drop the ethtool -S entry [Vladimir]
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt may discard packets if Rx completions are consumed
in an attempt to let netpoll make progress. It should be
extremely rare in practice but nonetheless such events
should be counted.
Since completion ring memory is allocated dynamically use
a similar scheme to what is done for HW stats to save them.
Report the stats in rx_dropped and per-netdev ethtool
counter. Chances that users care which ring dropped are
very low.
v3: only save the stat to rx_dropped on reset,
rx_total_netpoll_discards will now only show drops since
last reset, similar to other "total_discard" counters.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Link: https://lore.kernel.org/r/62522a24-f39a-2b35-1577-1fbb41695bed@gmail.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Michael Chan