This patch populates the PCI bus info in the ethtool driver query data.
Users will be able to view PCI bus info using 'ethtool -i <interface>'.
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IP register MAC_HW_Feature1[ADDR64] only defines
32/40/64 bit width, but some SOCs support others like i.MX8MP
support 34 bits but it maps to 40 bits width in MAC_HW_Feature1[ADDR64].
So overwrite dma_cap.addr64 according to HW real design.
Fixes: 94abdad697 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding reference clock (1us tic) for all LPI timer on Intel platforms.
The reference clock is derived from ptp clk. This also enables all LPI
counter.
Signed-off-by: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.
When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
will pass up all rx packets that failed address filtering (similar to
promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
filters and get routed to selected VFFQ Rx queue.
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.
<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+ +----+ +---+ +----------+
| EQoS | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
| MAC | |xPCS| |IF | | PHY |
+----------+ +----+ +---+ +----------+
^ ^ ^ ^
| | | |
+---------------------MDIO-------------------------+
PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the initial hooks for TBS support. This needs a 32 byte descriptor
in order for it to work with current HW. Adds all the logic for Enhanced
Descriptors in main core but no HW related logic for now.
Changes from v2:
- Use bitfield for TBS status / support (Jakub)
- Remove unneeded cache alignment (Jakub)
- Fix checkpatch issues
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adds the support for EST in GMAC5+ cores. This feature allows to offload
scheduling of queues opening time to the IP.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhanced addressing mode is only required when more than 32 bits need to
be addressed. Add a DMA configuration parameter to enable this mode only
when needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In-between the MAC & PHY there can be a mode converter, which converts one
mode to another (e.g. GMII-to-RGMII).
The converter, can be passive (i.e. no driver or OS/SW information
required), so the MAC & PHY need to be configured differently.
For the `stmmac` driver, this is implemented via a `mac-mode` property in
the device-tree, which configures the MAC into a certain mode, and for the
PHY a `phy_interface` field will hold the mode of the PHY. The mode of the
PHY will be passed to the PHY and from there-on it work in a different
mode. If unspecified, the default `phy-mode` will be used for both.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EHL DW EQOS is running on a 200MHz clock. Setting up stmmac-clk,
ptp clock and ptp_max_adj to 200MHz.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RSS functionality and add the corresponding callbacks in
XGMAC core.
Changes from v1:
- Do not use magic constants (Jakub)
- Use ethtool_rxfh_indir_default() (Jakub)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tegra EQOS driver already resets the MDIO bus at probe time via the
reset GPIO specified in the phy-reset-gpios device tree property. There
is no need to reset the bus again later on.
This avoids the need to query the device tree for the snps,reset GPIO,
which is not part of the Tegra EQOS device tree bindings. This quiesces
an error message from the generic bus reset code if it doesn't find the
snps,reset related delays.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_reset hook is not set anywhere. Drop it to make
stmmac_mdio_reset() smaller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only OF platforms use the reset delays and these delays are only read in
stmmac_mdio_reset(). Move them from struct stmmac_mdio_bus_data to a
stack variable inside stmmac_mdio_reset() because that's the only usage
of these delays.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No platform uses the "reset_gpio" field from stmmac_mdio_bus_data
anymore. Drop it so we don't get any new consumers either.
Plain GPIO numbers are being deprecated in favor of GPIO descriptors. If
needed any new non-OF platform can add a GPIO descriptor lookup table.
devm_gpiod_get_optional() will find the GPIO in that case.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of PHYLINK conversion we stopped parsing the phy-handle property
from DT. Unfortunatelly, some wrapper drivers still rely on this phy
node to configure the PHY.
Let's restore the parsing of PHY handle while these wrapper drivers are
not fully converted to PHYLINK.
Fixes: 74371272f9 ("net: stmmac: Convert to phylink and remove phylib logic")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the
"snps,reset-gpio" for GPIO descriptors so we don't need to take care of
it inside the driver anymore.
The advantage of this is that we now preserve the GPIO flags which are
passed via devicetree. This is required on some newer Amlogic boards
which use an Open Drain pin for the reset GPIO. This pin can only output
a LOW signal or switch to input mode but it cannot output a HIGH signal.
There are already devicetree bindings for these special cases and GPIO
core already takes care of them but only if we use GPIO descriptors
instead of GPIO numbers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa the full gnu general public license is included in this
distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.706787045@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.
This way we can still use the coalesce command in PCI based setups.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new entry to HWIF table for XGMAC 2.10. For now we fill it with
empty callbacks which will be added in posterior patches.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of adding more ifthen logic for adding a new mac_device_info
setup function, it is easier to add a function pointer to the function
needed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to the recent multi-queue changes the driver would configure the
queues to use the AVB mode, but the mode then got switched to DCB. The
hardware still works fine in DCB mode, but my testing capabilities are
limited, so it's safer to revert to the prior setting anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX queues' routing.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX and TX queues' priority.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the multiple queues configuration in the Device Tree.
It was also created a set of structures to keep the RX and TX queues
configurations to be used in the driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to the
plat_stmmacenet_data structure. It also moves these platform variables
initialization to stmmac_platform. This was done for two reasons:
a) If PCI is used, platform related code is being executed in stmmac_main
resulting in warnings that have no sense and conceptually was not right
b) stmmac as a synopsys reference ethernet driver stack will be hosting
more and more drivers to its structure like synopsys/dwc_eth_qos.c.
These drivers have their own DT bindings that are not compatible with
stmmac's. One of the most important are the clock names, and so they need
to be parsed in the glue logic and initialized there, and that is the main
reason why the clocks were passed to the platform structure.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For core revision 3.x Address-Aligned Beats is available in two registers.
The DT property snps,aal was created for AAL in the DMA bus register,
which is a read/write bit.
The DT property snps,axi_all was created for AXI_AAL in the AXI bus mode
register, which is a read only bit that reflects the value of AAL in the
DMA bus register.
Since the value of snps,axi_all is never used in the driver,
and since the property was created for a bit that is read only,
it should be safe to remove the property.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of adding hooks inside stmmac_platform it is better to just use
the standard PM callbacks within the specific dwmac-driver. This only
used by the dwmac-rk driver.
This reverts commit cecbc5563a ("stmmac: allow to split suspend/resume
from init/exit callbacks").
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the stmmac platform drivers provide dedicated suspend and resume
callbacks rather than always re-using the init and exits callbacks.
If the driver does not provide the suspend or resume callback, we fall
back to the old behavior trying to use exit or init.
This allows a specific platform to perform only a partial power-down on
suspend if Wake-on-Lan is enabled but always perform the full shutdown
sequence if the module is unloaded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 88f8b1bb41.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch manages the case when you have an Ethernet MAC with
a "fixed link", and not connected to a normal MDIO-managed PHY device.
The test of phy_bus_name was not helpful because it was never affected
and replaced by the mdio test node.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.
After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.
For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all dwmac-* drivers have been converted to have a proper probe
function the setup callback can now be removed. Also remove the
free callback that wasn't used by any driver.
New dwmac-* drivers should implement standard probe and remove
functions to preform any needed setup and teardown.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As dwmac-* drivers that need OF match have been converted
to use their own internal OF match data structure this can
now be removed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of these fields are unused and has been unused since they
were added 3 and 5 years ago. Drop them since they are clearly
not very useful.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>