A couple of mlx5 fixes related to cvq
A couple of reverts dropping useless code (code that used it got reverted
earlier)
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmJKyK4PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpE40IAIvsq1WDsXfg/649lp0wMO5MPEzAvCfgQpub
hCti2lKY4K9Ykqh+uTipDTxpRmg3wt/4QlQ6NYZVmn8jQ1JsNAIFCkc7ptG1xwQI
0RypofGsFQwbar2vKh8jEzYUsIbwLKeLNlib113fH9zyDRw7KjRppUgC2cjMoYv6
JhlOFZAApzFknXC/I8fmJyzVYpX+v2GB8RX2wWiNXHQZ9hkdKd1IvJqRiuRuSY3L
haubMBFG8hrdW8qQ40ngvt+GnrxKUustmPM6x9DCJYaMkKRkXC6NxueUcIk6qWiw
UJz5IOXURdJ3i1qxmkMGSnJiYbFpmwVGlqRekN3qNVpXNovfbg0=
=l15S
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Fixes and cleanups:
- A couple of mlx5 fixes related to cvq
- A couple of reverts dropping useless code (code that used it got
reverted earlier)"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa: mlx5: synchronize driver status with CVQ
vdpa: mlx5: prevent cvq work from hogging CPU
Revert "virtio_config: introduce a new .enable_cbs method"
Revert "virtio: use virtio_device_ready() in virtio_device_restore()"
vdpa generic device type support
More virtio hardening for broken devices
On the same theme, revert some virtio hotplug hardening patches -
they were misusing some interrupt flags, will have to be reverted.
RSS support in virtio-net
max device MTU support in mlx5 vdpa
akcipher support in virtio-crypto
shared IRQ support in ifcvf vdpa
a minor performance improvement in vhost
Enable virtio mem for ARM64
beginnings of advance dma support
Cleanups, fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmJEEk8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpcpUH+wRIXrzveirsN4MYH0aAeF+SLYaA5pgtO4U7
da22HYtwlMrDRMxwjepKBOTSu89uP5LEK7IKWPj9VRZg+GLz/Cdfc6BZl/fND3qt
0yFpwG1ZLsBK1+WHbysWQneEbPjXqQdbh9eVkKVGcNkRuLJJwXbmF95dyQEJwzeh
dPHssDcEC2tRgHAMrLyjLPKwMCRwcgtdPoB1ZC+lqTs3G6lktAfREEvqVfJOVe1b
mQcgdAJ+aRM0J/w/PYTmxFOZPYAmQ6hmAQ8Hf7nkjfRWQ4EM91W0cKAoZPc/+7KN
ZfFKVL28GEZLJqnx+3xijwCR2gwVHsRYZHaTjfGgQUWZPoB3Vrc=
=ynRx
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- vdpa generic device type support
- more virtio hardening for broken devices (but on the same theme,
revert some virtio hotplug hardening patches - they were misusing
some interrupt flags and had to be reverted)
- RSS support in virtio-net
- max device MTU support in mlx5 vdpa
- akcipher support in virtio-crypto
- shared IRQ support in ifcvf vdpa
- a minor performance improvement in vhost
- enable virtio mem for ARM64
- beginnings of advance dma support
- cleanups, fixes all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (33 commits)
vdpa/mlx5: Avoid processing works if workqueue was destroyed
vhost: handle error while adding split ranges to iotlb
vdpa: support exposing the count of vqs to userspace
vdpa: change the type of nvqs to u32
vdpa: support exposing the config size to userspace
vdpa/mlx5: re-create forwarding rules after mac modified
virtio: pci: check bar values read from virtio config space
Revert "virtio_pci: harden MSI-X interrupts"
Revert "virtio-pci: harden INTX interrupts"
drivers/net/virtio_net: Added RSS hash report control.
drivers/net/virtio_net: Added RSS hash report.
drivers/net/virtio_net: Added basic RSS support.
drivers/net/virtio_net: Fixed padded vheader to use v1 with hash.
virtio: use virtio_device_ready() in virtio_device_restore()
tools/virtio: compile with -pthread
tools/virtio: fix after premapped buf support
virtio_ring: remove flags check for unmap packed indirect desc
virtio_ring: remove flags check for unmap split indirect desc
virtio_ring: rename vring_unmap_state_packed() to vring_unmap_extra_packed()
net/mlx5: Add support for configuring max device MTU
...
Currently, CVQ doesn't have any synchronization with the driver
status. Then CVQ emulation code run in the middle of:
1) device reset
2) device status changed
3) map updating
The will lead several unexpected issue like trying to execute CVQ
command after the driver has been teared down.
Fixing this by using reslock to synchronize CVQ emulation code with
the driver status changing:
- protect the whole device reset, status changing and set_map()
updating with reslock
- protect the CVQ handler with the reslock and check
VIRTIO_CONFIG_S_DRIVER_OK in the CVQ handler
This will guarantee that:
1) CVQ handler won't work if VIRTIO_CONFIG_S_DRIVER_OK is not set
2) CVQ handler will see a consistent state of the driver instead of
the partial one when it is running in the middle of the
teardown_driver() or setup_driver().
Cc: 5262912ef3 ("vdpa/mlx5: Add support for control VQ and MAC setting")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220329042109.4029-2-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>
A userspace triggerable infinite loop could happen in
mlx5_cvq_kick_handler() if userspace keeps sending a huge amount of
cvq requests.
Fixing this by introducing a quota and re-queue the work if we're out
of the budget (currently the implicit budget is one) . While at it,
using a per device work struct to avoid on demand memory allocation
for cvq.
Fixes: 5262912ef3 ("vdpa/mlx5: Add support for control VQ and MAC setting")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220329042109.4029-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>
If mlx5_vdpa gets unloaded while a VM is running, the workqueue will be
destroyed. However, vhost might still have reference to the kick
function and might attempt to push new works. This could lead to null
pointer dereference.
To fix this, set mvdev->wq to NULL just before destroying and verify
that the workqueue is not NULL in mlx5_vdpa_kick_vq before attempting to
push a new work.
Fixes: 5262912ef3 ("vdpa/mlx5: Add support for control VQ and MAC setting")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220321141303.9586-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change vdpa_device.nvqs and vhost_vdpa.nvqs to use u32
Signed-off-by: Longpeng <longpeng2@huawei.com>
Link: https://lore.kernel.org/r/20220315032553.455-3-longpeng2@huawei.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Longpeng <<a href="mailto:longpeng2@huawei.com" target="_blank">longpeng2@huawei.com</a>><br></blockquote><div><br></div><div>Acked-by: Jason Wang <<a href="mailto:jasowang@redhat.com">jasowang@redhat.com</a>></div><div> </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
When MAC Address has been modified in guest, we only re-add the
Mac to mpfs, it is not enough, because the guest network will
not work correctly: the reply package from outside will go
straight away to the host VF net interface.
This patch recreate the flow rules, and make it work correctly.
Signed-off-by: Michael Qiu <qiudayu@archeros.com>
Link: https://lore.kernel.org/r/1648446492-17614-1-git-send-email-08005325@163.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Allow an admin creating a vdpa device to specify the max MTU for the
net device.
For example, to create a device with max MTU of 1000, the following
command can be used:
$ vdpa dev add name vdpa-a mgmtdev auxiliary/mlx5_core.sf.1 mtu 1000
This configuration mechanism assumes that vdpa is the sole real user of
the function. mlx5_core could theoretically change the mtu of the
function using the ip command on the mlx5_core net device but this
should not be done.
Reviewed-by: Si-Wei Liu<si-wei.liu@oracle.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220221121927.194728-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
On some platforms/devices, there may not be enough MSI vectors
allocated for the virtqueues and config changes. In such a case,
the interrupt sources(virtqueues, config changes) must share
an IRQ/vector, to avoid initialization failures, keep
the device functional.
This commit handles three cases:
(1) number of the allocated vectors == the number of virtqueues + 1
(config changes), every virtqueue and the config interrupt has
a separated vector/IRQ, the best and the most likely case.
(2) number of the allocated vectors is less than the best case, but
greater than 1. In this case, all virtqueues share a vector/IRQ,
the config interrupt has a separated vector/IRQ
(3) only one vector is allocated, in this case, the virtqueues and
the config interrupt share a vector/IRQ. The worst and most
unlikely case.
Otherwise, it needs to fail.
This commit introduces some helper functions:
ifcvf_set_vq_vector() and ifcvf_set_config_vector() sets virtqueue
vector and config vector in the device config space, so that
the device can send interrupt DMA.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Link: https://lore.kernel.org/r/20220222115428.998334-5-lingshan.zhu@intel.com
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220315124130.1710030-1-trix@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Including:
- IOMMU Core changes:
- Removal of aux domain related code as it is basically dead
and will be replaced by iommu-fd framework
- Split of iommu_ops to carry domain-specific call-backs
separatly
- Cleanup to remove useless ops->capable implementations
- Improve 32-bit free space estimate in iova allocator
- Intel VT-d updates:
- Various cleanups of the driver
- Support for ATS of SoC-integrated devices listed in
ACPI/SATC table
- ARM SMMU updates:
- Fix SMMUv3 soft lockup during continuous stream of events
- Fix error path for Qualcomm SMMU probe()
- Rework SMMU IRQ setup to prepare the ground for PMU support
- Minor cleanups and refactoring
- AMD IOMMU driver:
- Some minor cleanups and error-handling fixes
- Rockchip IOMMU driver:
- Use standard driver registration
- MSM IOMMU driver:
- Minor cleanup and change to standard driver registration
- Mediatek IOMMU driver:
- Fixes for IOTLB flushing logic
-----BEGIN PGP SIGNATURE-----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=bcqr
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- IOMMU Core changes:
- Removal of aux domain related code as it is basically dead and
will be replaced by iommu-fd framework
- Split of iommu_ops to carry domain-specific call-backs separatly
- Cleanup to remove useless ops->capable implementations
- Improve 32-bit free space estimate in iova allocator
- Intel VT-d updates:
- Various cleanups of the driver
- Support for ATS of SoC-integrated devices listed in ACPI/SATC
table
- ARM SMMU updates:
- Fix SMMUv3 soft lockup during continuous stream of events
- Fix error path for Qualcomm SMMU probe()
- Rework SMMU IRQ setup to prepare the ground for PMU support
- Minor cleanups and refactoring
- AMD IOMMU driver:
- Some minor cleanups and error-handling fixes
- Rockchip IOMMU driver:
- Use standard driver registration
- MSM IOMMU driver:
- Minor cleanup and change to standard driver registration
- Mediatek IOMMU driver:
- Fixes for IOTLB flushing logic
* tag 'iommu-updates-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (47 commits)
iommu/amd: Improve amd_iommu_v2_exit()
iommu/amd: Remove unused struct fault.devid
iommu/amd: Clean up function declarations
iommu/amd: Call memunmap in error path
iommu/arm-smmu: Account for PMU interrupts
iommu/vt-d: Enable ATS for the devices in SATC table
iommu/vt-d: Remove unused function intel_svm_capable()
iommu/vt-d: Add missing "__init" for rmrr_sanity_check()
iommu/vt-d: Move intel_iommu_ops to header file
iommu/vt-d: Fix indentation of goto labels
iommu/vt-d: Remove unnecessary prototypes
iommu/vt-d: Remove unnecessary includes
iommu/vt-d: Remove DEFER_DEVICE_DOMAIN_INFO
iommu/vt-d: Remove domain and devinfo mempool
iommu/vt-d: Remove iova_cache_get/put()
iommu/vt-d: Remove finding domain in dmar_insert_one_dev_info()
iommu/vt-d: Remove intel_iommu::domains
iommu/mediatek: Always tlb_flush_all when each PM resume
iommu/mediatek: Add tlb_lock in tlb_flush_all
iommu/mediatek: Remove the power status checking in tlb flush all
...
When vp_vdpa driver is unbind, vp_vdpa is freed in vdpa_unregister_device
and then vp_vdpa->mdev.pci_dev is dereferenced in vp_modern_remove,
triggering use-after-free.
Call Trace of unbinding driver free vp_vdpa :
do_syscall_64
vfs_write
kernfs_fop_write_iter
device_release_driver_internal
pci_device_remove
vp_vdpa_remove
vdpa_unregister_device
kobject_release
device_release
kfree
Call Trace of dereference vp_vdpa->mdev.pci_dev:
vp_modern_remove
pci_release_selected_regions
pci_release_region
pci_resource_len
pci_resource_end
(dev)->resource[(bar)].end
Signed-off-by: Zhang Min <zhang.min9@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Link: https://lore.kernel.org/r/20220301091059.46869-1-wang.yi59@zte.com.cn
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: 64b9f64f80 ("vdpa: introduce virtio pci driver")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
This fixes the following smatch warnings:
drivers/vdpa/vdpa_user/iova_domain.c:305 vduse_domain_alloc_iova() warn: should 'iova_pfn << shift' be a 64 bit type?
Fixes: 8c773d53fb ("vduse: Implement an MMU-based software IOTLB")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Link: https://lore.kernel.org/r/20220121083940.102-1-xieyongji@bytedance.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
When control vq receives a VIRTIO_NET_CTRL_MQ_VQ_PAIRS_SET command
request from the driver, presently there is no validation against the
number of queue pairs to configure, or even if multiqueue had been
negotiated or not is unverified. This may lead to kernel panic due to
uninitialized resource for the queues were there any bogus request
sent down by untrusted driver. Tie up the loose ends there.
Fixes: 52893733f2 ("vdpa/mlx5: Add multiqueue support")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1642206481-30721-4-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Per VIRTIO v1.1 specification, section 5.1.3.1 Feature bit requirements:
"VIRTIO_NET_F_MQ Requires VIRTIO_NET_F_CTRL_VQ".
There's assumption in the mlx5_vdpa multiqueue code that MQ must come
together with CTRL_VQ. However, there's nowhere in the upper layer to
guarantee this assumption would hold. Were there an untrusted driver
sending down MQ without CTRL_VQ, it would compromise various spots for
e.g. is_index_valid() and is_ctrl_vq_idx(). Although this doesn't end
up with immediate panic or security loophole as of today's code, the
chance for this to be taken advantage of due to future code change is
not zero.
Harden the crispy assumption by failing the set_driver_features() call
when seeing (MQ && !CTRL_VQ). For that end, verify_min_features() is
renamed to verify_driver_features() to reflect the fact that it now does
more than just validate the minimum features. verify_driver_features()
is now used to accommodate various checks against the driver features
for set_driver_features().
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1642206481-30721-3-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
No functional change introduced. vdpa bus driver such as virtio_vdpa
or vhost_vdpa is not supposed to take care of the locking for core
by its own. The locked API vdpa_set_features should suffice the
bus driver's need.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/1642206481-30721-2-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Currently the rcache structures are allocated for all IOVA domains, even if
they do not use "fast" alloc+free interface. This is wasteful of memory.
In addition, fails in init_iova_rcaches() are not handled safely, which is
less than ideal.
Make "fast" users call a separate rcache init explicitly, which includes
error checking.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/1643882360-241739-1-git-send-email-john.garry@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
partial support for < MAX_ORDER - 1 granularity for virtio-mem
driver_override for vdpa
sysfs ABI documentation for vdpa
multiqueue config support for mlx5 vdpa
Misc fixes, cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHiDHkPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpVT4H/3Veixt3uYPOmuLU2tSx+8X+sFTtik81hyiE
okz5fRJrxxA8SqS76FnmO10FS4hlPOGNk0Z5WVhr0yihwFvPLvpCM/xi2Lmrz9I7
pB0sXOIocEL1xApsxukR9K1Twpb2hfYsflbJYUVlRfhS5G0izKJNZp5I7OPrzd80
vVNNDWKW2iLDlfqsavumI4Kvm4nsFuCHG03jzMtcIa7YTXYV3DORD4ZGFFVUOIQN
t5F74TznwHOeYgJeg7TzjFjfPWmXjLetvx10QX1A1uOvwppWW/QY6My0UafTXNXj
VB3gOwJPf+gxXAXl/4bafq4NzM0xys6cpcPpjvhmU+erY4UuyAU=
=Y1eO
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
Modify the code such that ndev->cur_num_vqs better reflects the actual
number of data virtqueues. The value can be accurately realized after
features have been negotiated.
This is to prevent possible failures when modifying the RQT object if
the cur_num_vqs bears invalid value.
No issue was actually encountered but this also makes the code more
readable.
Fixes: c5a5cd3d3217 ("vdpa/mlx5: Support configuring max data virtqueue")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220111183400.38418-5-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Si-Wei Liu<si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Make sure the decision whether an index received through a callback is
valid or not consults the negotiated features.
The motivation for this was due to a case encountered where I shut down
the VM. After the reset operation was called features were already
clear, I got get_vq_state() call which caused out array bounds
access since is_index_valid() reported the index value.
So this is more of not hit a bug since the call shouldn't have been made
first place.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220111183400.38418-4-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Si-Wei Liu<si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Avoid the wrapper holding cf_mutex since it is not protecting anything.
To avoid confusion and unnecessary overhead incurred by it, remove.
Fixes: f489f27bc0ab ("vdpa: Sync calls set/get config/status with cf_mutex")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220111183400.38418-2-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Si-Wei Liu<si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Configure max supported virtqueues features on the management device.
This info can be retrieved using:
$ vdpa mgmtdev show
vdpasim_net:
supported_classes net
max_supported_vqs 2
dev_features MAC ANY_LAYOUT VERSION_1 ACCESS_PLATFORM
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-15-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
All masks in this file are 64 bits. Change BIT to BIT_ULL.
Other occurences use (1 << val) which yields a 32 bit value. Change them
to use BIT_ULL too.
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-14-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Configure max supported virtqueues on the management device.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-13-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Configure max supported virtqueues and features on the management
device.
This info can be retrieved using:
$ vdpa mgmtdev show
auxiliary/mlx5_core.sf.1:
supported_classes net
max_supported_vqs 257
dev_features CSUM GUEST_CSUM MTU HOST_TSO4 HOST_TSO6 STATUS CTRL_VQ MQ \
CTRL_MAC_ADDR VERSION_1 ACCESS_PLATFORM
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-12-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Si-Wei Liu<si-wei.liu@oracle.com>
Add max_supported_vqs and supported_features fields to struct
vdpa_mgmt_dev. Upstream drivers need to feel these values according to
the device capabilities.
These values are reported back in a netlink message when showing management
devices.
Examples:
$ auxiliary/mlx5_core.sf.1:
supported_classes net
max_supported_vqs 257
dev_features CSUM GUEST_CSUM MTU HOST_TSO4 HOST_TSO6 STATUS CTRL_VQ MQ \
CTRL_MAC_ADDR VERSION_1 ACCESS_PLATFORM
$ vdpa -j mgmtdev show
{"mgmtdev":{"auxiliary/mlx5_core.sf.1":{"supported_classes":["net"], \
"max_supported_vqs":257,"dev_features":["CSUM","GUEST_CSUM","MTU", \
"HOST_TSO4","HOST_TSO6","STATUS","CTRL_VQ","MQ","CTRL_MAC_ADDR", \
"VERSION_1","ACCESS_PLATFORM"]}}}
$ vdpa -jp mgmtdev show
{
"mgmtdev": {
"auxiliary/mlx5_core.sf.1": {
"supported_classes": [ "net" ],
"max_supported_vqs": 257,
"dev_features": ["CSUM","GUEST_CSUM","MTU","HOST_TSO4", \
"HOST_TSO6","STATUS","CTRL_VQ","MQ", \
"CTRL_MAC_ADDR","VERSION_1","ACCESS_PLATFORM"]
}
}
}
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-11-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Si-Wei Liu<si-wei.liu@oracle.com>
Restore ndev->cur_num_vqs to the original value in case change_num_qps()
fails.
Fixes: 52893733f2 ("vdpa/mlx5: Add multiqueue support")
Reviewed-by: Si-Wei Liu<si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-10-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add netlink attribute to store the negotiated features. This can be used
by userspace to get the current state of the vdpa instance.
Examples:
$ vdpa dev config show vdpa-a
vdpa-a: mac 00:00:00:00:88:88 link up link_announce false max_vq_pairs 16 mtu 1500
negotiated_features CSUM GUEST_CSUM MTU MAC HOST_TSO4 HOST_TSO6 STATUS \
CTRL_VQ MQ CTRL_MAC_ADDR VERSION_1 ACCESS_PLATFORM
$ vdpa -j dev config show vdpa-a
{"config":{"vdpa-a":{"mac":"00:00:00:00:88:88","link ":"up","link_announce":false, \
"max_vq_pairs":16,"mtu":1500,"negotiated_features":["CSUM","GUEST_CSUM","MTU","MAC", \
"HOST_TSO4","HOST_TSO6","STATUS","CTRL_VQ","MQ","CTRL_MAC_ADDR","VERSION_1", \
"ACCESS_PLATFORM"]}}}
$ vdpa -jp dev config show vdpa-a
{
"config": {
"vdpa-a": {
"mac": "00:00:00:00:88:88",
"link ": "up",
"link_announce ": false,
"max_vq_pairs": 16,
"mtu": 1500,
"negotiated_features": [
"CSUM","GUEST_CSUM","MTU","MAC","HOST_TSO4","HOST_TSO6","STATUS","CTRL_VQ","MQ", \
"CTRL_MAC_ADDR","VERSION_1","ACCESS_PLATFORM"
]
}
}
}
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-9-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Check whether the max number of data virtqueue pairs was provided when a
adding a new device and verify the new value does not exceed device
capabilities.
In addition, change the arrays holding virtqueue and callback contexts
to be dynamically allocated.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-8-elic@nvidia.com
Includes fixup:
vdpa/mlx5: fix error handling in mlx5_vdpa_dev_add()
Clang build fails with
mlx5_vnet.c:2574:6: error: variable 'mvdev' is used uninitialized whenever
'if' condition is true
if (!ndev->vqs || !ndev->event_cbs) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlx5_vnet.c:2660:14: note: uninitialized use occurs here
put_device(&mvdev->vdev.dev);
^~~~~
This because mvdev is set after trying to allocate ndev->vqs,event_cbs.
So move the allocation to after mvdev is set but before the arrays
are used in init_mvqs()
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220107211352.3940570-1-trix@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Includes fixup:
vdpa/mlx5: fix endian-ness for max vqs
sparse warnings: (new ones prefixed by >>)
>> drivers/vdpa/mlx5/net/mlx5_vnet.c:1247:23: sparse: sparse: cast to restricted __le16
>> drivers/vdpa/mlx5/net/mlx5_vnet.c:1247:23: sparse: sparse: cast from restricted __virtio16
> 1247 num = le16_to_cpu(ndev->config.max_virtqueue_pairs);
Address this using the appropriate wrapper.
Cc: "Eli Cohen" <elic@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Fix VDPA_ATTR_DEV_NET_CFG_MACADDR assignment to be explicit 64 bit
assignment.
No issue was seen since the value is well below 64 bit max value.
Nevertheless it needs to be fixed.
Fixes: a007d94004 ("vdpa/mlx5: Support configuration of MAC")
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-7-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add netlink support to configure the max virtqueue pairs for a device.
At least one pair is required. The maximum is dictated by the device.
Example:
$ vdpa dev add name vdpa-a mgmtdev auxiliary/mlx5_core.sf.1 max_vqp 4
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-6-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid reading device configuration during feature negotiation. Read
device status and verify that VIRTIO_CONFIG_S_FEATURES_OK is set.
Protect the entire operation, including configuration read with cf_mutex
to ensure integrity of the results.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-5-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Add wrappers to get/set status and protect these operations with
cf_mutex to serialize these operations with respect to get/set config
operations.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-4-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Distribute the available rx virtqueues amongst the available RQT
entries.
RQTs require to have a power of two entries. When creating or modifying
the RQT, use the lowest number of power of two entries that is not less
than the number of rx virtqueues. Distribute them in the available
entries such that some virtqueus may be referenced twice.
This allows to configure any number of virtqueue pairs when multiqueue
is used.
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-3-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Provide an interface to read the negotiated features. This is needed
when building the netlink message in vdpa_dev_net_config_fill().
Also fix the implementation of vdpa_dev_net_config_fill() to use the
negotiated features instead of the device features.
To make APIs clearer, make the following name changes to struct
vdpa_config_ops so they better describe their operations:
get_features -> get_device_features
set_features -> set_driver_features
Finally, add get_driver_features to return the negotiated features and
add implementation to all the upstream drivers.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20220105114646.577224-2-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove overriding of virtio_version_1_0 which forced the virtqueue
object to version 1.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20211230142024.142979-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
When 'pcim_enable_device()' is used, some resources become automagically
managed.
There is no need to call 'pci_free_irq_vectors()' when the driver is
removed. The same will already be done by 'pcim_release()'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/02045bdcbbb25f79bae4827f66029cfcddc90381.1636301587.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Make sure to offer VIRTIO_NET_F_MTU since we configure the MTU based on
what was queried from the device.
This allows the virtio driver to allocate large enough buffers based on
the reported MTU.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20211124170949.51725-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
`driver_override` allows to control which of the vDPA bus drivers
binds to a vDPA device.
If `driver_override` is not set, the previous behaviour is followed:
devices use the first vDPA bus driver loaded (unless auto binding
is disabled).
Tested on Fedora 34 with driverctl(8):
$ modprobe virtio-vdpa
$ modprobe vhost-vdpa
$ modprobe vdpa-sim-net
$ vdpa dev add mgmtdev vdpasim_net name dev1
# dev1 is attached to the first vDPA bus driver loaded
$ driverctl -b vdpa list-devices
dev1 virtio_vdpa
$ driverctl -b vdpa set-override dev1 vhost_vdpa
$ driverctl -b vdpa list-devices
dev1 vhost_vdpa [*]
Note: driverctl(8) integrates with udev so the binding is
preserved.
Suggested-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211126164753.181829-3-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit fixes a misuse of virtio-net device config size issue
for virtio-block devices.
A new member config_size in struct ifcvf_hw is introduced and would
be initialized through vdpa_dev_add() to record correct device
config size.
To be more generic, rename ifcvf_hw.net_config to ifcvf_hw.dev_config,
the helpers ifcvf_read/write_net_config() to ifcvf_read/write_dev_config()
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Reported-and-suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Fixes: 6ad31d162a ("vDPA/ifcvf: enable Intel C5000X-PL virtio-block for vDPA")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211201081255.60187-1-lingshan.zhu@intel.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Including:
- Identity domain support for virtio-iommu
- Move flush queue code into iommu-dma
- Some fixes for AMD IOMMU suspend/resume support when x2apic
is used
- Arm SMMU Updates from Will Deacon:
- Revert evtq and priq back to their former sizes
- Return early on short-descriptor page-table allocation failure
- Fix page fault reporting for Adreno GPU on SMMUv2
- Make SMMUv3 MMU notifier ops 'const'
- Numerous new compatible strings for Qualcomm SMMUv2 implementations
- Various smaller fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=Q8LV
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Identity domain support for virtio-iommu
- Move flush queue code into iommu-dma
- Some fixes for AMD IOMMU suspend/resume support when x2apic is used
- Arm SMMU Updates from Will Deacon:
- Revert evtq and priq back to their former sizes
- Return early on short-descriptor page-table allocation failure
- Fix page fault reporting for Adreno GPU on SMMUv2
- Make SMMUv3 MMU notifier ops 'const'
- Numerous new compatible strings for Qualcomm SMMUv2 implementations
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (38 commits)
iommu/iova: Temporarily include dma-mapping.h from iova.h
iommu: Move flush queue data into iommu_dma_cookie
iommu/iova: Move flush queue code to iommu-dma
iommu/iova: Consolidate flush queue code
iommu/vt-d: Use put_pages_list
iommu/amd: Use put_pages_list
iommu/amd: Simplify pagetable freeing
iommu/iova: Squash flush_cb abstraction
iommu/iova: Squash entry_dtor abstraction
iommu/iova: Fix race between FQ timeout and teardown
iommu/amd: Fix typo in *glues … together* in comment
iommu/vt-d: Remove unused dma_to_mm_pfn function
iommu/vt-d: Drop duplicate check in dma_pte_free_pagetable()
iommu/vt-d: Use bitmap_zalloc() when applicable
iommu/amd: Remove useless irq affinity notifier
iommu/amd: X2apic mode: mask/unmask interrupts on suspend/resume
iommu/amd: X2apic mode: setup the INTX registers on mask/unmask
iommu/amd: X2apic mode: re-enable after resume
iommu/amd: Restore GA log/tail pointer on host resume
iommu/iova: Move fast alloc size roundup into alloc_iova_fast()
...
Here is the set of changes for the driver core for 5.17-rc1.
Lots of little things here, including:
- kobj_type cleanups
- auxiliary_bus documentation updates
- auxiliary_device conversions for some drivers (relevant
subsystems all have provided acks for these)
- kernfs lock contention reduction for some workloads
- other tiny cleanups and changes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYd7deA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym8ngCgw0ANwrRPE5b1dthEmfU2f8Knk5kAn0pHQv6R
VRZJypgNfU/Pt0ykstZD
=CO9J
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of changes for the driver core for 5.17-rc1.
Lots of little things here, including:
- kobj_type cleanups
- auxiliary_bus documentation updates
- auxiliary_device conversions for some drivers (relevant subsystems
all have provided acks for these)
- kernfs lock contention reduction for some workloads
- other tiny cleanups and changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (43 commits)
kobject documentation: remove default_attrs information
drivers/firmware: Add missing platform_device_put() in sysfb_create_simplefb
debugfs: lockdown: Allow reading debugfs files that are not world readable
driver core: Make bus notifiers in right order in really_probe()
driver core: Move driver_sysfs_remove() after driver_sysfs_add()
firmware: edd: remove empty default_attrs array
firmware: dmi-sysfs: use default_groups in kobj_type
qemu_fw_cfg: use default_groups in kobj_type
firmware: memmap: use default_groups in kobj_type
sh: sq: use default_groups in kobj_type
headers/uninline: Uninline single-use function: kobject_has_children()
devtmpfs: mount with noexec and nosuid
driver core: Simplify async probe test code by using ktime_ms_delta()
nilfs2: use default_groups in kobj_type
kobject: remove kset from struct kset_uevent_ops callbacks
driver core: make kobj_type constant.
driver core: platform: document registration-failure requirement
vdpa/mlx5: Use auxiliary_device driver data helpers
net/mlx5e: Use auxiliary_device driver data helpers
soundwire: intel: Use auxiliary_device driver data helpers
...
Use auxiliary_get_drvdata and auxiliary_set_drvdata helpers.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211221235852.323752-5-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It really is a property of the IOVA rcache code that we need to alloc a
power-of-2 size, so relocate the functionality to resize into
alloc_iova_fast(), rather than the callsites.
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1638875846-23993-1-git-send-email-john.garry@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
virtio device id value can be more than 31. Hence, use BIT_ULL in
assignment.
Fixes: 33b347503f ("vdpa: Define vdpa mgmt device, ops and a netlink interface")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20211130042949.88958-1-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This condition checks "len" but it does not check "offset" and that
could result in an out of bounds read if "offset > dev->config_size".
The problem is that since both variables are unsigned the
"dev->config_size - offset" subtraction would result in a very high
unsigned value.
I think these checks might not be necessary because "len" and "offset"
are supposed to already have been validated using the
vhost_vdpa_config_validate() function. But I do not know the code
perfectly, and I like to be safe.
Fixes: c8a6153b6c ("vduse: Introduce VDUSE - vDPA Device in Userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211208150956.GA29160@kili
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@vger.kernel.org
