KX022A is a 3-axis accelerometer from ROHM/Kionix. The sensor features
include variable ODRs, I2C and SPI control, FIFO/LIFO with watermark IRQ,
tap/motion detection, wake-up & back-to-sleep events, four acceleration
ranges (2, 4, 8 and 16g), and probably some other cool features.
Add support for the basic accelerometer features such as getting the
acceleration data via IIO. (raw reads, triggered buffer [data-ready] or
using the WMI IRQ).
Important things to be added include the double-tap, motion
detection and wake-up as well as the runtime power management.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/758b00d6aea0a6431a5a3a78d557d449c113b21e.1666614295.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MSA311 is a tri-axial, low-g accelerometer with I2C digital output for
sensitivity consumer applications. It has dynamic user-selectable full
scales range of +-2g/+-4g/+-8g/+-16g and allows acceleration measurements
with output data rates from 1Hz to 1000Hz.
This driver supports following MSA311 features:
- IIO interface
- Different power modes: NORMAL and SUSPEND (using pm_runtime)
- ODR (Output Data Rate) selection
- Scale and samp_freq selection
- IIO triggered buffer, IIO reg access
- NEW_DATA interrupt + trigger
Below features to be done:
- Motion Events: ACTIVE, TAP, ORIENT, FREEFALL
- Low Power mode
Datasheet: https://cdn-shop.adafruit.com/product-files/5309/MSA311-V1.1-ENG.pdf
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220822175011.2886-4-ddrokosov@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADXL367 is an ultralow power, 3-axis MEMS accelerometer.
The ADXL367 does not alias input signals to achieve ultralow power
consumption, it samples the full bandwidth of the sensor at all
data rates. Measurement ranges of +-2g, +-4g, and +-8g are available,
with a resolution of 0.25mg/LSB on the +-2 g range.
In addition to its ultralow power consumption, the ADXL367
has many features to enable true system level power reduction.
It includes a deep multimode output FIFO, a built-in micropower
temperature sensor, and an internal ADC for synchronous conversion
of an additional analog input.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220214073810.781016-6-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add basic support for NXP FXLS8962AF/FXLS8964AF Automotive
accelerometers.
It will allow setting up scale/gain and reading x,y,z
axis.
Datasheet: https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
Datasheet: https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BMI088 is a combined module with both accelerometer and gyroscope.
This adds the accelerometer driver support for the SPI interface.
The gyroscope part is already supported by the BMG160 driver.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210125150732.23873-2-mike.looijmans@topic.nl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add basic support for the Bosch Sensortec BMA400 3-axes ultra-low power
accelerometer when configured to use SPI.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a IIO driver for the Bosch BMA400 3-axes ultra-low power accelerometer.
The driver supports reading from the acceleration and temperature
registers. The driver also supports reading and configuring the output data
rate, oversampling ratio, and scale.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adxl372 is designed to communicate in either SPI or I2C protocol. It
autodetects the format being used, requiring no configuration control to
select the format.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch restructures the existing adxl372 driver by adding a module for
SPI and a header file, while the baseline module deals with the chip-logic.
This is a necessary step, as this driver should support in the future
a similar device which differs only in the type of interface used (I2C
instead of SPI).
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds basic support for Analog Devices ADXL372 SPI-Bus
Three-Axis Digital Accelerometer.
The device is probed and configured the with some initial default
values. With this basic driver, it is possible to read raw acceleration
data.
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL372.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the adis16209 driver out of staging directory and merge to the
mainline IIO subsystem.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move adis16201 driver out of staging and merge into mainline
IIO subsystem.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver to support older EC firmware that only support deprecated
ec command. Rely on ACPI memory map register to access sensor
information.
Present same interface as the regular cros_ec sensor stack:
- one iio device per accelerometer
- use HTML5 axis definition
- use iio abi units
- accept calibration calls, but do nothing
Chrome can use the same code than regular cros_ec sensor stack to
calculate orientation and lid angle.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI driver that initializes SPI regmap for the adxl345 core driver.
The driver supports the same functionality as I2C namely the x, y, z and
scale readings.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move I2C-specific code into its own file and rely on regmap to access
registers. The core code provides access to x, y, z and scale readings.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add basic IIO support for the Analog Devices ADXL345 3-axis accelerometer.
The datasheet can be found here:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL345.pdf
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now the driver is in a reasonable state, lets get it (finally) out
of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Add an iio driver for the MiraMEMS DA280 3-axis 14-bit accelerometer, as
well as for the DA226 which is a fully compatible 2-axis version.
Datasheets for the DA280 and DA226 can be found at the manufacturers site:
http://www.miramems.com/en/products.asp?list=1
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver is based on the DA311 Android driver which can be found here:
1e70113a5b/drivers/amlogic/input/sensor
the mir3da_* files are the DA311 driver.
Unfortunately there is no datasheet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a driver for the Domintech ARD10 3-axis Accelerometer, based on the
android driver found here: https://github.com/domintech/dmard10
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds I2C regmap transport for the KXSD9 driver.
Tested on the KXSD9 sensor on the APQ8060 Dragonboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This moves the KXSD9 SPI transport out to its own file and Kconfig
entry, so that we will be able to add another transport method.
We export the common probe and add a local header file for the
functionality shared between the main driver and the transport
driver.
We make the SPI transport the default for the driver if SPI is
available and the KXSD9 driver was selected, so the oldconfig
upgrade path will be clear.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Domintech DMARD09 3-axis
accelerometer. Only supports reading the x,y,z axes at the moment.
Implementation based on the Android driver from the Acer Liquid E2
kernel sources.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch add support for Domintech DMARD05, DMARD06 and DMARD07
accelerometers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit adds basic support for the Bosch Sensortec BMA220
digital triaxial acceleration sensor.
The device datasheet can be found here:
http://www.mouser.com/pdfdocs/BSTBMA220DS00308.PDF
Includes:
- raw readings
- ACPI detection
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Freescale
MMA7660FC 3-axis accelerometer. Datasheet:
http://www.nxp.com/files/sensors/doc/data_sheet/MMA7660FC.pdf
Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: Constantin Musca <constantin.musca@intel.com>
Reviewed-by: Martin Klepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Freescale MMA7455L/MMA7456L 3-axis in 10-bit mode for
I2C and SPI bus. This rather simple driver that currently doesn't
support all the hardware features of MMA7455L/MMA7456L.
Tested on Embedded Artist's LPC4357 Dev Kit with MMA7455L on I2C bus.
Data sheets for the two devices can be found here:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA7455L.pdfhttp://cache.freescale.com/files/sensors/doc/data_sheet/MMA7456L.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a minimal implementation for the Memsic MXC6255XC
orientation sensing accelerometer. The supported operations are reading
raw acceleration values for X/Y axis that can be scaled using the
exposed scale.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a simple SPI driver which initializes the spi regmap for the bmc150
core driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Memsic MXC4005XC 3-axis accelerometer. The
current implementation is a minimal one as it adds raw readings for the
three axes and setting scale from userspace.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Sensortek
STK8BA50 3-axis accelerometer. Datasheet:
http://szgsensor.com/uploads/soft/141229/STK8BA50%D2%E5%BC%CE.pdf
Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Sensortek
STK8312 3-axis accelerometer. Datasheet:
http://www.syi-group.com/uploadpic/data/201361817562681623.pdf
Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Freescale MMA9553L Intelligent Pedometer Platform.
The following functionalities are supported:
- step counter (counts the number of steps using a HW register)
- step detector (generates an iio event at every step the user takes)
- activity recognition (rest, walking, jogging, running)
- speed
- calories
- distance
To get accurate pedometer results, the user's height, weight and gender
need to be configured.
The specifications can be downloaded from:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA955xLSWRM.pdfhttp://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds accelerometer iio driver which uses sensorhub as data
provider.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Freescale has the MMA955xL family of devices that use the
same communication protocol (based on i2c messages):
http://www.freescale.com/files/sensors/doc/data_sheet/MMA955xL.pdf.
To support more devices from this family, we need to split the
mma9551 driver so we can export the common functions that will
be used by other mma955x drivers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Freescale MMA9551L Intelligent Motion-Sensing Platform.
The driver supports raw reads for acceleration and inclination, as well
as configuring inclination rate-of-change events. The events can be
used similarly to an Android sensor Tilt event.
The specifications can be downloaded from:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA955xLSWRM.pdf
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This change implements BMC150 accelerometer driver. A BMC150 package
consist of a compass and an accelerometer. This driver only implements
accelerometer part.
Spec downloaded from:
http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-03.pdf
This sensor chip supports many advanced features, but this driver
implements minimum feature set which is a must to be useful.
This driver can be enhanced incrementally.
If the sensor vendor wants to update full featured version, they
can substitute or enhance this driver when they get chance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds IIO driver for KXCJK 1013 triaxis accelerometer sensor.
The specifications for this driver is downloaded from:
http://www.kionix.com/sites/default/files/KXCJK-1013%20Specifications%20Rev%202.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
3-axis accelerometer sensor (2/4/8 g) with 12-bit resolution
and I2C interface
many extra features are unsupported (freefall detection, orientation
change, autosleep)
datasheet is here:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8452Q.pdf
v2: (thanks to Jonathan Cameron)
* use ARRAY_SIZE()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.
Also reorder those entries which weren't in alphabetical order yet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Matti Vaittinen