Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that URB_NO_SETUP_DMA_MAP is no longer in use, this patch (as1376)
removes all references to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the parallel port on the moschip MCS7715 device. The port
registers itself with the parport subsystem as a low-level driver. A separate
entry to the kernel configuration is added beneath that for the mos7720, to
avoid the need to link with the parport subsystem code for users who don't have
or don't want the parallel port. Only compatibility mode is currently supported
(no ECP/EPP). Tested with both moschip devices (7720 and 7715) on UP and SMP
hosts, including regression testing of serial port, concurrent operation of
serial and parallel ports, and various connect / disconnect scenarios.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bulk endpoint streams were added in the USB 3.0 specification. Streams
allow a device driver to overload a bulk endpoint so that multiple
transfers can be queued at once.
The device then decides which transfer it wants to work on first, and can
queue part of a transfer before it switches to a new stream. All this
switching is invisible to the device driver, which just gets a completion
for the URB. Drivers that use streams must be able to handle URBs
completing in a different order than they were submitted to the endpoint.
This requires adding new API to set up xHCI data structures to support
multiple queues ("stream rings") per endpoint. Drivers will allocate a
number of stream IDs before enqueueing URBs to the bulk endpoints of the
device, and free the stream IDs in their disconnect function. See
Documentation/usb/bulk-streams.txt for details.
The new mass storage device class, USB Attached SCSI Protocol (UASP), uses
these streams API.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1367) deprecates USB's power/level sysfs attribute in
favor of the power/control attribute provided by the runtime PM core.
The two attributes do the same thing.
It would be nice to replace power/level with a symlink to
power/control, but at the moment sysfs doesn't offer any way to do so.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_hid is a USB gadget driver implementing the Human Interface Device class
specification. The driver handles basic HID protocol handling in the
kernel, and allows userspace to read/write HID reports trough /dev/hidgX
character devices.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix obvious cases of "it's" being used when "its" was meant.
Signed-off-by: Francis Galiegue <fgaliegue@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework. This involves numerous changes throughout
usbcore, especially to hub.c and driver.c. Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.
Several fields in the usb_device and usb_interface structures are no
longer needed. Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).
The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else. They won't remain
suspended. But if they aren't in use then they will naturally
autosuspend again in a few seconds.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1326) adds usb_enable_autosuspend() and
usb_disable_autosuspend() routines for use by drivers. If a driver
knows that its device can handle suspends and resumes correctly, it
can enable autosuspend all by itself. This is equivalent to the user
writing "auto" to the device's power/level attribute.
The implementation differs slightly from what it used to be. Now
autosuspend is disabled simply by doing usb_autoresume_device() (to
increment the usage counter) and enabled by doing
usb_autosuspend_device() (to decrement the usage counter).
The set_level() attribute method is updated to use the new routines,
and the USB Power-Management documentation is updated.
The patch adds a usb_enable_autosuspend() call to the hub driver's
probe routine, allowing the special-case code for hubs in quirks.c to
be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1316) adds some error checking to usb_submit_urb().
It's conditional on CONFIG_USB_DEBUG, so it won't affect normal users.
The new check makes sure that the actual type of the endpoint
described by urb->pipe agrees with the type encoded in the pipe value.
The USB error code documentation is updated to include the code
returned by the new check, and the usbfs SUBMITURB handler is updated
to use the correct pipe type when legacy user code tries to submit a
bulk transfer to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1313) updates the documentation concerning USB power
management.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1303) revises the USB Power Management infrastructure to
make it compatible with the new driver-model Runtime PM framework:
Drivers are no longer allowed to access intf->pm_usage_cnt
directly; the PM framework manages its own usage counters.
usb_autopm_set_interface() is eliminated, because it directly
sets intf->pm_usage_cnt.
usb_autopm_enable() and usb_autopm_disable() are eliminated,
because they call usb_autopm_set_interface().
usb_autopm_get_interface_no_resume() and
usb_autopm_put_interface_no_suspend() are added. They
correspond to pm_runtime_get_noresume() and
pm_runtime_put_noidle() in the PM framework.
The power/level attribute no longer accepts "suspend", only
"on" and "auto". The PM framework doesn't allow devices to be
forced into a suspended mode.
The hub driver contains the only code that violates the new
guidelines. It is updated to use the new interface routines instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Neither /sys/usb/devices nor /sys/bus/devices exist. The correct path
is /sys/bus/usb/devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hi there.
On Aug 21 2009, Alan Stern wrote:
> On Thu, 20 Aug 2009, Rogério Brito wrote:
> > Again, just reiterating, what I said before, even though I am not sure
> > if I can reproduce it, I will try to.
>
> A usbmon trace showing what happens when you plug in the drive and
> when you run smartctl would help.
The documentation for usbmon in the kernel 2.6.31-rc7 kernel doesn't
match what the kernel exposes in the debug fs tree. This patch fixes it.
Signed-off-by: Rogério Brito <rbrito@ime.usp.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I think this sentence was confusing regarding the possible size
of the data area.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an extension to the binary API so it reaches parity with
existing text API (so-called "1u"). The extension delivers additional data,
such as ISO descriptors and the interrupt interval.
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1160b) adds support routines for asynchronous autosuspend
and autoresume, with accompanying documentation updates. There
already are several potential users of this interface, and others are
likely to arise as autosuspend support becomes more widespread.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a comment and clarifies the documentation about the
endianness of descriptors. The current policy is that descriptors will
be little-endian at the API even on big-endian systems; however the
/proc/bus/usb API predates this policy and presents descriptors with
some multibyte fields byte-swapped.
Signed-off-by: Phil Endecott <usb_endian_patch@chezphil.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 7bb5ea54 (usb gadget serial: use composite gadget framework)
changed the default for the use_acm parameter from 0 to 1.
Update the documentation to match.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The example is incorrect: there is no 0t socket (the '1t' format has no
bus number in it). Also, correct the broken sentence for USB Tag.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The UWB radio manager coordinates the use of the radio between the
PALs that may be using it. PALs request use of the radio with
uwb_radio_start() and the radio manager will start beaconing if its
not already doing so. When the last PAL has called uwb_radio_stop()
beaconing will be stopped.
In the future, the radio manager will have a more sophisticated channel
selection algorithm, probably following the Channel Selection Policy
from the WiMedia Alliance when it is finalized. For now, channel 9
(BG1, TFC1) is selected.
The user may override the channel selected by the radio manager and may
force the radio to stop beaconing.
The WUSB Host Controller PAL makes use of this and there are two new
debug PAL commands that can be used for testing.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Correct errors in the descriptions for usb_autopm_enable
and usb_autopm_disable in the USB PM doc.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds Documentation for the extensions of the anchor API.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added basic support for a Delcom USB 7-segment LED Display
Signed-off by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simplify the sysfs ABI of the wusb-cbaf (Cable Based Association)
driver: use one value per file and cause the write of the CHID to
fetch the CDID (instead of requiring a separate read).
Update the example wusb-cbaf script to work with this revised ABI.
Signed-off-by: Felipe Zimmerle <felipe.zimmerle@indt.org.br>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Documentation (and example utilities) for the UWB (and WUSB) stacks.
Some of the documentation may be out-of-date.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
this mentions a new deadlock due to advanced power management.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1109b) makes USB-Persist more resilient to errors. With
the current code, if a normal resume fails, it's an unrecoverable
error. With the patch, if a normal resume fails (and if the device is
enabled for USB-Persist) then a reset-resume is tried.
This fixes the problem reported in Bugzilla #10977.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Teach "gadget serial" to use the new abstracted (and bugfixed) TTY glue,
and remove all the orignal tangled-up code. Update the documentation
accordingly. This is a net object code shrink and cleanup; it should
make it a lot easier to see how the TTY glue should accomodate updates
to the TTY layer, be bugfixed, etc.
Notable behavior changes include: it can now support getty even when
there's no USB connection; it fits properly into the mdev/udev world;
and RX handling is better (throttling works, and low latency).
Configurations with scripts setting up the /dev/ttygserial device node
(with "experimental" major number) may want to change that to be a
symlink pointing to the /dev/ttyGS0 file, as a migration aid; else,
just switch entirely over to mdev/udev.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds documentation about the new usb anchor infrastructure.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1048) extends the descriptor checking after a device is
reset. Now the SerialNumber string descriptor is compared to its old
value, in addition to the device and configuration descriptors.
As a consequence, the kmalloc() call in usb_string() is now on the
error-handling pathway for usb-storage. Hence its allocation type is
changed to GFO_NOIO.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1047) removes the USB_PERSIST Kconfig option, enabling
it permanently. It also prevents the power/persist attribute from
being created for hub devices; there's no point in having it since
USB-PERSIST is always turned on for hubs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1014) was partly written by Tilman Schmidt. It
clarifies the USB power-management documentation by explaining that
when a disconnect occurs, a suspend method call might not be followed
by either a resume or a reset_resume call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as998) adds documentation on how USB power management
works and how to use it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a USB serial port driver for the Winchiphead
CH341 USB-RS232 Converter. This chip also implements an IEEE 1284
parallel port, I2C and SPI, but that is not supported by the driver.
Signed-off-by: Frank A Kingswood <frank@kingswood-consulting.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update usbmon documentation, mentioning the "zero" (wildcard) bus.
Possibly, in my first hunk, the 'either ... or ...' should be rephrased a bit to
be expressed better.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates some of the documentation about DMA buffer management
for USB, and ways to avoid extra copying. Our understanding of the issues
has improved over time.
- Most drivers should *avoid* the dma-coherent allocators. There are
a few exceptions (like the HID driver).
- Some methods are currently commented out; it seems folk writing
USB drivers aren't doing performance tuning at that level yet.
- Just avoid highmem; there's no good way to pass an "I can do highmem
DMA" capability through a driver stack. This is easy, everything
already avoids highmem. But it'd be nice if x86_32 systems with much
physical memory could use it directly with network adapters and mass
storage devices. (Patch, anyone?)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as920) adds an extra level of protection to the
USB-Persist facility. Now it will apply by default only to hubs; for
all other devices the user must enable it explicitly by setting the
power/persist device attribute.
The disconnect_all_children() routine in hub.c has been removed and
its code placed inline. This is the way it was originally as part of
hub_pre_reset(); the revised usage in hub_reset_resume() is
sufficiently different that the code can no longer be shared.
Likewise, mark_children_for_reset() is now inline as part of
hub_reset_resume(). The end result looks much cleaner than before.
The sysfs interface is updated to add the new attribute file, and
there are corresponding documentation updates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert files within the Documentation directory to UTF-8.
Adrian Bunk:
small additional fixes
Signed-off-by: John Anthony Kazos Jr. <jakj@j-a-k-j.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
I am no longer with CTI. The Support Department will handle all
inquiries regarding the WH.
Signed-off-by: Stuart MacDonald <stuartm@connecttech.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new text API, codenamed '1u', which captures more URB
fields than old '1t' interface did. Also the '1u' text API is compatible
with the future "bus zero" extension.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new, "binary" API in addition to the old, text API usbmon
had before. The new API allows for less CPU use, and it allows to capture
all data from a packet where old API only captured 32 bytes at most. There
are some limitations and conditions to this, e.g. in case someone constructs
a URB with 1GB of data, it's not likely to be captured, because even the
huge buffers of the new reader are finite. Nonetheless, I expect this new
capability to capture all data for all real life scenarios.
The downside is, a special user mode application is required where cat(1)
worked before. I have sample code at http://people.redhat.com/zaitcev/linux/
and Paolo Abeni is working on patching libpcap.
This patch was initially written by Paolo and later I tweaked it, and
we had a little back-and-forth. So this is a jointly authored patch, but
I am submitting this I am responsible for the bugs.
Signed-off-by: Paolo Abeni <paolo.abeni@email.it>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update /proc/bus/usb/devices output to report active altsettings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes a few mentions of my email address to point to the new one,
leaving things like old copyright messages alone.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes typos in various Documentation txts. The patch addresses some
misc words.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses some
+words starting with the letter 'T'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch add AIRcable USBto USB-HID blacklist, makes some little
changes things in the Kconfig to make AIRcable USB look as all the rest
of drivers. And it removes the readme part that was on
Documentation/usb/usb-serial.txt because it is not needed anymore.
Signed-off-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove many duplicated words under Documentation/ and do other small
cleanups.
Examples:
"and and" --> "and"
"in in" --> "in"
"the the" --> "the"
"the the" --> "to the"
...
Signed-off-by: Paolo Ornati <ornati@fastwebnet.it>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letter 'S'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letters 'N'-'P'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letters 'H'-'M'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. This patch addresses
some words starting with the letters 'D'-'E'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Now that devfs is removed, there's no longer any need to document how to
do this or that with devfs.
This patch includes some improvements by Joe Perches.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add driver for AIRcable USB Bluetooth dongle.
Signed-off-by: Naranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Text from the back of the box, for your information/amusement:
USB DATA CABLE
FOR K700 Series
The USB Cable is an ideal link between your mobile phone and PC. Employing
the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
such as synchronization of phone book and calendar,as well as Internet browsing via
a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.
MADE IN CHINA
From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the documentation. Apparently, I left unedited copy-paste results
in examples. Also, Alan helped me to improve the most confusing parts.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Move documentation for usb v4l devices from
Documentation/usb to Documentation/video4linux.
- Removed trailing whitespace.
- Update Kconfig help text links to reflect the new file locations.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ZC0301 driver updates.
Changes: + new, - removed, * cleanup, @ bugfix
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Cleanups and updates in the documentation
+ Use per-device sensor structures
+ Add frame_timeout module parameter
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ET61X[12]51 driver updates
Changes: + new, - removed, * cleanup, @ bugfix
@ Fix stream_interrupt()
@ Fix vidioc_enum_input() and split vidioc_gs_input()
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
when waiting for video frames
* replace wake_up_interruptible(&wait_stream) with wake_up(&wait_stream)
* Cleanups and updates in the documentation
* Use mutexes instead of semaphores
+ Use per-device sensor structures
+ Add support for PAS202BCA image sensors
+ Add frame_timeout module parameter
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates.
Changes: + new, - removed, * cleanup, @ bugfix
@ Fix stream_interrupt()
@ Fix vidioc_enum_input() and split vidioc_gs_input()
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
when waiting for video frames
* replace wake_up_interruptible(&wait_stream) with wake_up(&wait_stream)
* Cleanups and updates in the documentation
+ Use per-device sensor structures
+ Add support for PAS202BCA image sensors
+ Add frame_timeout module parameter
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"Cosmetic" driver updates for the ZC0301 driver:
- Fix stream_interrupt() (and work around a possible kernel bug);
- Fix vidioc_enum_input() and split vidioc_gs_input() in two parts;
- Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
when waiting for video frames;
- replace erroneous wake_up_interruptible(&wait_stream) with
wake_up(&wait_stream);
- Cosmetic cleanups in the documentation.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver for ZC0301
Image Processor and Control Chip.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- the w9968cf-vpp module is not intended for inclusion into the kernel
- the upstream w9968cf package shipping the w9968cf-vpp module suggests
to simply replace the w9968cf module shipped with the kernel
Therefore, there seems to be no good reason spending some bytes of
kernel memory for hooks for the w9968cf-vpp module.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver giving support
to ET61X151 and ET61X251 PC Camera Controllers made by
Etoms Electronics.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates:
- Use kzalloc() instead of kmalloc()
- Move some macro definitions from sn9c102.h to sn9c102_core.c
- Use vfree() and vmalloc_32() instead of rvfree() and rvmalloc()
- Fix mmap() sys call
- Documentation updates
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates and bugfixes.
Changes: + new, - removed, * cleanup, @ bugfix:
@ fix poll()
@ Remove bad get_ctrl()'s
* Reduce ioctl stack usage
* Remove final ";" from some macro definitions
* Better support for SN9C103
+ Add sn9c102_write_regs()
+ Add 0x0c45/0x602d to the list of SN9C10x based devices
+ Add support for OV7630 image sensors
+ Provide support for the built-in microphone interface of the SN9C103
+ Documentation updates
+ Add 0x0c45/0x602e to the list of SN9C10x based devices
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as611) fixes a minor mistake and misspelling in the USB
documentation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct lots of URLs in Documentation/ Also a few minor whitespace cleanups
and typo/spello fixes. Sadly there are still a lot of bad URLs remaining.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch deletes the bluetooth.txt help file of the bluetty driver and
hands over its major device nodes for character devices to the RFCOMM TTY
implementation of the Bluetooth subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (as564) updates Documentation/usb/URB.txt, bringing it roughly
up to the current level.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update Documentation/usb/proc_usb_info.txt:
- remove some trailing whitespace
- add a blank line before each T: line to match current kernel
and to make the text more readable.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch fixes the following spelling errors in Documentation/
- double "the"
- Several misspellings of function/functionality
- infomation
- memeory
- Recieved
- wether
and possibly others which I forgot ;-)
Trailing whitespaces on the same line as the typo are also deleted.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
