The command "ethtool -L <intf> combined 0" may clean the RX/TX channel
count and skip the error path, since the attrs
tb[ETHTOOL_A_CHANNELS_RX_COUNT] and tb[ETHTOOL_A_CHANNELS_TX_COUNT]
are NULL in this case when recent ethtool is used.
Tested using ethtool v5.10.
Fixes: 7be92514b9 ("ethtool: check if there is at least one channel for TX/RX in the core")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Link: https://lore.kernel.org/r/20210225125102.23989-1-simon.horman@netronome.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding.
For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.
Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also performs auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).
Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.
Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.
Export is_hsr_master so DSA can tell them apart from other devices in
dsa_slave_changeupper.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool does not expose how many lanes are used when the
link is up.
After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.
Extend ethtool to expose the number of lanes currently in use for
drivers that support it.
For example:
$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE Backplane ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
50000baseKR/Full
50000baseSR/Full
50000baseCR/Full
50000baseLR_ER_FR/Full
50000baseDR/Full
100000baseKR2/Full
100000baseSR2/Full
100000baseCR2/Full
100000baseLR2_ER2_FR2/Full
100000baseDR2/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Advertised link modes: 100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.
This would be a cleanup for next patch that would add another validation
to the new function.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a new netdev feature, NETIF_F_GRO_UDP_FWD, to allow user
to turn UDP GRO on and off for forwarding.
Defaults to off to not change current datapath.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix two error paths in ethnl_set_channels() to avoid lock-up caused
but unreleased RTNL.
Fixes: e19c591eaf ("ethtool: set device channel counts with CHANNELS_SET request")
Reported-by: LiLiang <liali@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/r/20201215090810.801777-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported a stack overflow in bitmap_from_arr32() called from
ethnl_parse_bitset() when bitset from netlink message is longer than
target bitmap length. While ethnl_compact_sanity_checks() makes sure that
trailing part is all zeros (i.e. the request does not try to touch bits
kernel does not recognize), we also need to cap change_bits to nbits so
that we don't try to write past the prepared bitmaps.
Fixes: 88db6d1e4f ("ethtool: add ethnl_parse_bitset() helper")
Reported-by: syzbot+9d39fa49d4df294aab93@syzkaller.appspotmail.com
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/r/3487ee3a98e14cd526f55b6caaa959d2dcbcad9f.1607465316.git.mkubecek@suse.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After updating userspace Ethtool from 5.7 to 5.9, I noticed that
NETDEV_FEAT_CHANGE is no more raised when changing netdev features
through Ethtool.
That's because the old Ethtool ioctl interface always calls
netdev_features_change() at the end of user request processing to
inform the kernel that our netdevice has some features changed, but
the new Netlink interface does not. Instead, it just notifies itself
with ETHTOOL_MSG_FEATURES_NTF.
Replace this ethtool_notify() call with netdev_features_change(), so
the kernel will be aware of any features changes, just like in case
with the ioctl interface. This does not omit Ethtool notifications,
as Ethtool itself listens to NETDEV_FEAT_CHANGE and drops
ETHTOOL_MSG_FEATURES_NTF on it
(net/ethtool/netlink.c:ethnl_netdev_event()).
From v1 [1]:
- dropped extra new line as advised by Jakub;
- no functional changes.
[1] https://lore.kernel.org/netdev/AlZXQ2o5uuTVHCfNGOiGgJ8vJ3KgO5YIWAnQjH0cDE@cp3-web-009.plabs.ch
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/r/ahA2YWXYICz5rbUSQqNG4roJ8OlJzzYQX7PTiG80@cp4-web-028.plabs.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This accidentally got wired up to the *get* policy instead
of the *set* policy, causing operations to be rejected. Fix
it by wiring up the correct policy instead.
Fixes: 5028588b62 ("ethtool: wire up set policies to ops")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ETHTOOL_A_STRSET_COUNTS_ONLY flag attribute was previously
not allowed to be used, but now due to the policy size reduction
we would access the tb[] array out of bounds since we tried to
check for the attribute despite it not being accepted.
Fix both issues by adding it correctly to the appropriate policy.
Fixes: ff419afa43 ("ethtool: trim policy tables")
Fixes: 71921690f9 ("ethtool: provide string sets with STRSET_GET request")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perform header flags validation through the policy.
Only pause command supports ETHTOOL_FLAG_STATS. Create a separate
policy to be able to express that in policy dumps to user space.
Note that even though the core will validate the header policy,
it cannot record multiple layers of attributes and we have to
re-parse header sub-attrs. When doing so we could skip attribute
validation, or use most permissive policy. Opt for the former.
We will no longer return the extack cookie for flags but since
we only added first new flag in this release it's not expected
that any user space had a chance to make use of it.
v2: - remove the re-validation in ethnl_parse_header_dev_get()
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get the most out of parsing by the core, and to allow dumping
full policies we need to specify which policy applies to nested
attrs. For headers it's ethnl_header_policy.
$ sed -i 's@\(ETHTOOL_A_.*HEADER\].*=\) { .type = NLA_NESTED },@\1\n\t\tNLA_POLICY_NESTED(ethnl_header_policy),@' net/ethtool/*
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ethtool uses strict attribute validation there's no need
to initialize all attributes in policy tables. 0 is NLA_UNSPEC
which is going to be rejected. Remove the NLA_REJECTs.
Similarly attributes above maxattrs are rejected, so there's
no need to always size the policy tables to ETHTOOL_A_..._MAX.
v2: - new patch
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to get commands wire up the policies of set commands
to get parsing by the core and policy dumps.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up policies for get commands in struct nla_policy of the ethtool
family. Make use of genetlink code attr validation and parsing, as well
as allow dumping policies to user space.
For every ETHTOOL_MSG_*_GET:
- add 'ethnl_' prefix to policy name
- add extern declaration in net/ethtool/netlink.h
- wire up the policy & attr in ethtool_genl_ops[].
- remove .request_policy and .max_attr from ethnl_request_ops.
Obviously core only records the first "layer" of parsed attrs
so we still need to parse the sub-attrs of the nested header
attribute.
v2:
- merge of patches 1 and 2 from v1
- remove stray empty lines in ops
- also remove .max_attr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define get/set phy tunable callbacks in ethtool ops.
This will allow MAC drivers with integrated PHY still to implement
these tunables.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like all genl families ethtool_genl_family needs to not
be a straight up constant, because it's modified/initialized
by genl_register_family(). After init, however, it's only
passed to genlmsg_put() & co. therefore we can mark it
as __ro_after_init.
Since genl_family structure contains function pointers
mark this as a fix.
Fixes: 2b4a8990b7 ("ethtool: introduce ethtool netlink interface")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel offload info code uses ETHTOOL_MSG_TUNNEL_INFO_GET message type (cmd
field in genetlink header) for replies to tunnel info netlink request, i.e.
the same value as the request have. This is a problem because we are using
two separate enums for userspace to kernel and kernel to userspace message
types so that this ETHTOOL_MSG_TUNNEL_INFO_GET (28) collides with
ETHTOOL_MSG_CABLE_TEST_TDR_NTF which is what message type 28 means for
kernel to userspace messages.
As the tunnel info request reached mainline in 5.9 merge window, we should
still be able to fix the reply message type without breaking backward
compatibility.
Fixes: c7d759eb7b ("ethtool: add tunnel info interface")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers have to report their pause frames statistics
via ethtool -S, and there is a wide variety of names used for
these statistics.
Add the two statistics defined in IEEE 802.3x to the standard
API. Create a new ethtool request header flag for including
statistics in the response to GET commands.
Always create the ETHTOOL_A_PAUSE_STATS nest in replies when
flag is set. Testing if driver declares the op is not a reliable
way of checking if any stats will actually be included and therefore
we don't want to give the impression that presence of
ETHTOOL_A_PAUSE_STATS indicates driver support.
Note that this patch does not include PFC counters, which may fit
better in dcbnl? But mostly I don't need them/have a setup to test
them so I haven't looked deeply into exposing them :)
v3:
- add a helper for "uninitializing" stats, rather than a cryptic
memset() (Andrew)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ops->set_phys_id() returned an error, previously we would only break
out of the inner loop, which neither stopped the outer loop nor returned
the error to the user (since 'rc' would be overwritten on the next pass
through the loop).
Thus, rewrite it to use a single loop, so that the break does the right
thing. Use u64 for 'count' and 'i' to prevent overflow in case of
(unreasonably) large values of id.data and n.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-09-01
The following pull-request contains BPF updates for your *net-next* tree.
There are two small conflicts when pulling, resolve as follows:
1) Merge conflict in tools/lib/bpf/libbpf.c between 88a8212028 ("libbpf: Factor
out common ELF operations and improve logging") in bpf-next and 1e891e513e
("libbpf: Fix map index used in error message") in net-next. Resolve by taking
the hunk in bpf-next:
[...]
scn = elf_sec_by_idx(obj, obj->efile.btf_maps_shndx);
data = elf_sec_data(obj, scn);
if (!scn || !data) {
pr_warn("elf: failed to get %s map definitions for %s\n",
MAPS_ELF_SEC, obj->path);
return -EINVAL;
}
[...]
2) Merge conflict in drivers/net/ethernet/mellanox/mlx5/core/en/xsk/rx.c between
9647c57b11 ("xsk: i40e: ice: ixgbe: mlx5: Test for dma_need_sync earlier for
better performance") in bpf-next and e20f0dbf20 ("net/mlx5e: RX, Add a prefetch
command for small L1_CACHE_BYTES") in net-next. Resolve the two locations by retaining
net_prefetch() and taking xsk_buff_dma_sync_for_cpu() from bpf-next. Should look like:
[...]
xdp_set_data_meta_invalid(xdp);
xsk_buff_dma_sync_for_cpu(xdp, rq->xsk_pool);
net_prefetch(xdp->data);
[...]
We've added 133 non-merge commits during the last 14 day(s) which contain
a total of 246 files changed, 13832 insertions(+), 3105 deletions(-).
The main changes are:
1) Initial support for sleepable BPF programs along with bpf_copy_from_user() helper
for tracing to reliably access user memory, from Alexei Starovoitov.
2) Add BPF infra for writing and parsing TCP header options, from Martin KaFai Lau.
3) bpf_d_path() helper for returning full path for given 'struct path', from Jiri Olsa.
4) AF_XDP support for shared umems between devices and queues, from Magnus Karlsson.
5) Initial prep work for full BPF-to-BPF call support in libbpf, from Andrii Nakryiko.
6) Generalize bpf_sk_storage map & add local storage for inodes, from KP Singh.
7) Implement sockmap/hash updates from BPF context, from Lorenz Bauer.
8) BPF xor verification for scalar types & add BPF link iterator, from Yonghong Song.
9) Use target's prog type for BPF_PROG_TYPE_EXT prog verification, from Udip Pant.
10) Rework BPF tracing samples to use libbpf loader, from Daniel T. Lee.
11) Fix xdpsock sample to really cycle through all buffers, from Weqaar Janjua.
12) Improve type safety for tun/veth XDP frame handling, from Maciej Żenczykowski.
13) Various smaller cleanups and improvements all over the place.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the AF_XDP zero-copy driver interface functions to better
reflect what they do after the replacement of umems with buffer
pools in the previous commit. Mostly it is about replacing the
umem name from the function names with xsk_buff and also have
them take the a buffer pool pointer instead of a umem. The
various ring functions have also been renamed in the process so
that they have the same naming convention as the internal
functions in xsk_queue.h. This so that it will be clearer what
they do and also for consistency.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-3-git-send-email-magnus.karlsson@intel.com
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
Set IP protocol mask only when IP protocol field is set.
This will allow flow-type ether with vlan rule which don't have
protocol field to apply.
ethtool -N ens5f4 flow-type ether proto 0x8100 vlan 0x600\
m 0x1FFF action 3 loc 16
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy ethtool userspace tool shows an error when no features could
be changed. It's useful to have a netlink reply to be able to show this
error when __netdev_update_features wasn't called, for example:
1. ethtool -k eth0
large-receive-offload: off
2. ethtool -K eth0 rx-fcs on
3. ethtool -K eth0 lro on
Could not change any device features
rx-lro: off [requested on]
4. ethtool -K eth0 lro on
# The output should be the same, but without this patch the kernel
# doesn't send the reply, and ethtool is unable to detect the error.
This commit makes ethtool-netlink always return a reply when requested,
and it still avoids unnecessary calls to __netdev_update_features if the
wanted features haven't changed.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool-netlink ignores dev->hw_features and may confuse the drivers by
asking them to enable features not in the hw_features bitmask. For
example:
1. ethtool -k eth0
tls-hw-tx-offload: off [fixed]
2. ethtool -K eth0 tls-hw-tx-offload on
tls-hw-tx-offload: on
3. ethtool -k eth0
tls-hw-tx-offload: on [fixed]
Fitler out dev->hw_features from req_wanted to fix it and to resemble
the legacy ethtool behavior.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool-netlink calculates new wanted bits as:
(req_wanted & req_mask) | (old_active & ~req_mask)
It completely discards the old wanted bits, so they are forgotten with
the next ethtool command. Sample steps to reproduce:
1. ethtool -k eth0
tx-tcp-segmentation: on # TSO is on from the beginning
2. ethtool -K eth0 tx off
tx-tcp-segmentation: off [not requested]
3. ethtool -k eth0
tx-tcp-segmentation: off [requested on]
4. ethtool -K eth0 rx off # Some change unrelated to TSO
5. ethtool -k eth0
tx-tcp-segmentation: off # "Wanted on" is forgotten
This commit fixes it by changing the formula to:
(req_wanted & req_mask) | (old_wanted & ~req_mask),
where old_active was replaced by old_wanted to account for the wanted
bits.
The shortcut condition for the case where nothing was changed now
compares wanted bitmasks, instead of wanted to active.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8oRdgACgkQSD+KveBX
+j4/LQgAkSjNzOaS7bVDzhoYL3aBQOMIzgocJUeVi7xXH8IO1uy55mNDrKBqjxbW
dy9U9VsvV5i2V2qkkQLvHVkoDSg8Buo2Uxu4OrZHOLN0KfbFrra4VvmB1CzEBix8
FICnQaZZcE7529P04TgZ8Mo9vRb5VdJFhqED5Nvegy+y8FolEsQYbjIoDBE6wa0j
Meqa/29+XCE5FzTOjbbQWizAnRZMbkxtSSreDNgeHxke9eMSO+fmwKScng63QUfl
7nfU6dW6A0d1kHhpL5RqAFOcmkpSdqYaA3SA+/8pPT9X3yOAkxE6KTKGIixpB9JX
zQt+Wkna49jJ/JfDQB5vgww5c0HjAQ==
=j0fG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-08-03
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 has the IANA VXLAN port (4789) hard coded by the device,
instead of being added dynamically when tunnels are created.
To support this add a workaround flag to struct udp_tunnel_nic_info.
Skipping updates for the port is fairly trivial, dumping the hard
coded port via ethtool requires some code duplication. The port
is not a part of any real table, we dump it in a special table
which has no tunnel types supported and only one entry.
This is the last known workaround / hack needed to convert
all drivers to the new infra.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the genlmsg_put() call in ethnl_default_dumpit() fails, we bail out
without checking if we already have some messages in current skb like we do
with ethnl_default_dump_one() failure later. Therefore if existing messages
almost fill up the buffer so that there is not enough space even for
netlink and genetlink header, we lose all prepared messages and return and
error.
Rather than duplicating the skb->len check, move the genlmsg_put(),
genlmsg_cancel() and genlmsg_end() calls into ethnl_default_dump_one().
This is also more logical as all message composition will be in
ethnl_default_dump_one() and only iteration logic will be left in
ethnl_default_dumpit().
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have moved the PHY ethtool statistics to be dynamically
registered, we no longer need to inline those for ethtool. This used to
be done to avoid cross symbol referencing and allow ethtool to be
decoupled from PHYLIB entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have introduced ethtool_phy_ops and the PHY library
dynamically registers its operations with that function pointer, we can
remove the direct PHYLIB dependency in favor of using dynamic
operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to decouple ethtool from its PHY library dependency, define an
ethtool_phy_ops singleton which can be overriden by the PHY library when
it loads with an appropriate set of function pointers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.
Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.
Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.
The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.
If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting SQI or maximum SQI value fails in linkstate_prepare_data(), we
must not return without calling ethnl_ops_complete(dev) as that could
result in imbalance between ethtool_ops ->begin() and ->complete() calls.
Fixes: 8066021915 ("ethtool: provide UAPI for PHY Signal Quality Index (SQI)")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
A last minute change put the TDR cable test parameters into a nest.
The validation is not sufficient, resulting in an oops if the nest is
missing. Set default values first, then update them if the nest is
provided.
Fixes: f2bc8ad31a ("net: ethtool: Allow PHY cable test TDR data to configured")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e585f23636 ("udp: Changes to udp_offload to support remote
checksum offload") added new GSO type and a corresponding netdev
feature, but missed Ethtool's 'netdev_features_strings' table.
Give it a name so it will be exposed to userspace and become available
for manual configuration.
v3:
- decouple from "netdev_features_strings[] cleanup" series;
- no functional changes.
v2:
- don't split the "Fixes:" tag across lines;
- no functional changes.
Fixes: e585f23636 ("udp: Changes to udp_offload to support remote checksum offload")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix check in ethtool_rx_flow_rule_create
Fixes: eca4205f9e ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b33583265 ("net: Add fraglist GRO/GSO feature flags") missed
an entry for NETIF_F_GSO_FRAGLIST in netdev_features_strings array. As
a result, fraglist GSO feature is not shown in 'ethtool -k' output and
can't be toggled on/off.
The fix is trivial.
Fixes: 3b33583265 ("net: Add fraglist GRO/GSO feature flags")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use array_size() helper instead of the open-coded version in
copy_to_user(). These sorts of multiplication factors need to
be wrapped in array_size().
This issue was found with the help of Coccinelle and, audited and fixed
manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code generates a Smatch warning:
net/ethtool/linkinfo.c:143 ethnl_set_linkinfo()
warn: variable dereferenced before check 'info' (see line 119)
Fortunately, the "info" pointer is never NULL so the check can be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot is reporting:
net/ethtool/cabletest.c:230:5: warning: no previous prototype for
Mark the function as static.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-05-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).
The main changes are:
1) Add a new AF_XDP buffer allocation API to the core in order to help
lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
as well as mlx5 have been moved over to the new API and also gained a
small improvement in performance, from Björn Töpel and Magnus Karlsson.
2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
in order to allow for e.g. reverse translation of load-balancer backend
to service address/port tuple from a connected peer, from Daniel Borkmann.
3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
being non-NULL, e.g. if after an initial test another non-NULL test on
that pointer follows in a given path, then it can be pruned right away,
from John Fastabend.
4) Larger rework of BPF sockmap selftests to make output easier to understand
and to reduce overall runtime as well as adding new BPF kTLS selftests
that run in combination with sockmap, also from John Fastabend.
5) Batch of misc updates to BPF selftests including fixing up test_align
to match verifier output again and moving it under test_progs, allowing
bpf_iter selftest to compile on machines with older vmlinux.h, and
updating config options for lirc and v6 segment routing helpers, from
Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.
6) Conversion of BPF tracing samples outdated internal BPF loader to use
libbpf API instead, from Daniel T. Lee.
7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
the XDP selftests, from Jesper Dangaard Brouer.
8) Minor improvements to libbpf's internal hashmap implementation, from
Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.
v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call drivers if nothing changed. Netlink code already
contains this logic.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a channel config with no ability to RX or TX traffic is
clearly wrong. Check for this in the core so the drivers don't
have to.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given that it takes time to run a cable test, send a notify message at
the start, as well as when it is completed.
v3:
EMSGSIZE when ethnl_bcastmsg_put() fails
Print an error message on failure, since this is a void function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PHY drivers can use these helpers for reporting the results. The
results get translated into netlink attributes which are added to the
pre-allocated skbuf.
v3:
Poison phydev->skb
Return -EMSGSIZE when ethnl_bcastmsg_put() fails
Return valid error code when nla_nest_start() fails
Use u8 for results
Actually put u32 length into message
v4:
s/ENOTSUPP/EOPNOTSUPP/g
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make some helpers for building ethtool netlink messages available
outside the compilation unit, so they can be used for building
messages which are not simple get/set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new ethtool netlink calls to trigger the starting of a PHY cable
test.
Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when
ETHTOOL_NETLINK is builtin, which would result in kernel linking errors.
v2:
Remove unwanted white space change
Remove ethnl_cable_test_act_ops and use doit handler
Rename cable_test_set_policy cable_test_act_policy
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY
v3:
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation
Remove unused cable_test_get_policy
Add Reviewed-by tags
v4:
Remove unwanted blank line
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is executing a self test, put the interface into
operative status testing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.
Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.
v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three string sets related to timestamping information:
ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
ETH_SS_TS_TX_TYPES: timestamping Tx types
ETH_SS_TS_RX_FILTERS: timestamping Rx filters
These will be used for TIMESTAMP_GET request.
v2: avoid compiler warning ("enumeration value not handled in switch")
in net_hwtstamp_validate()
v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network
device are modified using ETHTOOL_MSG_EEE_SET netlink message or
ETHTOOL_SEEE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_SET netlink request to set EEE settings of a network device.
These are traditionally set with ETHTOOL_SEEE ioctl request.
The netlink interface allows setting the EEE status for all link modes
supported by kernel but only first 32 link modes can be set at the moment
as only those are supported by the ethtool_ops callback.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_GET request to get EEE settings of a network device. These
are traditionally available via ETHTOOL_GEEE ioctl request.
The netlink interface allows reporting EEE status for all link modes
supported by kernel but only first 32 link modes are provided at the moment
as only those are reported by the ethtool_ops callback and drivers.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of
a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message
or ETHTOOL_SPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_SET netlink request to set pause parameters of a network
device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl
request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_GET request to get pause parameters of a network device.
These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters
of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink
message or ETHTOOL_SCOALESCE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement COALESCE_SET netlink request to set coalescing parameters of
a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Like the ioctl implementation, the generic ethtool code checks if only
supported parameters are modified; if not, first offending attribute is
reported using extack.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement COALESCE_GET request to get coalescing parameters of a network
device. These are traditionally available via ETHTOOL_GCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Omit attributes with zero values unless they are declared as supported
(i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is
set).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. One of them is
ethnl_set_privflags(), a simple reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool --set-priv-flags veth1 foo on
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
Fixes: f265d79959 ("ethtool: set device private flags with PRIVFLAGS_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduce a new netdev feature, which will be used by drivers
to state they can perform MACsec transformations in hardware.
The patchset was gathered by Mark, macsec functinality itself
was implemented by Dmitry, Mark and Pavel Belous.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.
The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).
Fixes: f70bb06563 ("ethtool: update mapping of features to legacy ioctl requests")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3af ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b3 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all in-tree drivers have been updated we can
make the supported_coalesce_params mandatory.
To save debugging time in case some driver was missed
(or is out of tree) add a warning when netdev is registered
with set_coalesce but without supported_coalesce_params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Jakub Kicinski, we ethtool netlink code should respond
with an error if request head has flags set which are not recognized by
kernel, either as a mistake or because it expects functionality introduced
in later kernel versions.
To avoid unnecessary roundtrips, use extack cookie to provide the
information about supported request flags.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of spelling mistakes in NL_SET_ERR_MSG_ATTR messages.
Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_CHANNELS_NTF notification whenever channel counts of
a network device are modified using ETHTOOL_MSG_CHANNELS_SET netlink
message or ETHTOOL_SCHANNELS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement CHANNELS_SET netlink request to set channel counts of a network
device. These are traditionally set with ETHTOOL_SCHANNELS ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack. Checks preventing removing channels
used for RX indirection table or zerocopy AF_XDP socket are also
implemented.
Move ethtool_get_max_rxfh_channel() helper into common.c so that it can be
used by both ioctl and netlink code.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement CHANNELS_GET request to get channel counts of a network device.
These are traditionally available via ETHTOOL_GCHANNELS ioctl request.
Omit attributes for channel types which are not supported by driver or
device (zero reported for maximum).
v2: (all suggested by Jakub Kicinski)
- minor cleanup in channels_prepare_data()
- more descriptive channels_reply_size()
- omit attributes with zero max count
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_RINGS_NTF notification whenever ring sizes of a network
device are modified using ETHTOOL_MSG_RINGS_SET netlink message or
ETHTOOL_SRINGPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement RINGS_SET netlink request to set ring sizes of a network device.
These are traditionally set with ETHTOOL_SRINGPARAM ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
