There is a new notification BUS_NOTIFY_DRIVER_NOT_BOUND that is issued when
driver fails during binding. In such case pm_clk_notify(), when PM_CLK=n,
leaves clocks enabled. Undo operations that have been done in
BUS_NOTIFY_BIND_DRIVER case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
If an architecture's main Kconfig file doesn't include
kernel/power/Kconfig, but CONFIG_PM=y and HAVE_CLK=y (e.g. m68knommu
allmodconfig):
drivers/base/power/clock_ops.c: In function ‘__pm_clk_add’:
drivers/base/power/clock_ops.c:106: error: ‘struct pm_subsys_data’ has no member named ‘clock_list’
drivers/base/power/clock_ops.c: At top level:
drivers/base/power/clock_ops.c:120: error: redefinition of ‘pm_clk_add’
include/linux/pm_clock.h:64: error: previous definition of ‘pm_clk_add’ was here
drivers/base/power/clock_ops.c:135: error: redefinition of ‘pm_clk_add_clk’
include/linux/pm_clock.h:69: error: previous definition of ‘pm_clk_add_clk’ was here
drivers/base/power/clock_ops.c:171: error: redefinition of ‘pm_clk_remove’
include/linux/pm_clock.h:73: error: previous definition of ‘pm_clk_remove’ was here
drivers/base/power/clock_ops.c: In function ‘pm_clk_remove’:
drivers/base/power/clock_ops.c:180: error: ‘struct pm_subsys_data’ has no member named ‘clock_list’
drivers/base/power/clock_ops.c:180: error: ‘struct pm_subsys_data’ has no member named ‘clock_list’
drivers/base/power/clock_ops.c: At top level:
drivers/base/power/clock_ops.c:207: error: redefinition of ‘pm_clk_init’
include/linux/pm_clock.h:54: error: previous definition of ‘pm_clk_init’ was here
drivers/base/power/clock_ops.c: In function ‘pm_clk_init’:
drivers/base/power/clock_ops.c:210: error: ‘struct pm_subsys_data’ has no member named ‘clock_list’
drivers/base/power/clock_ops.c: At top level:
drivers/base/power/clock_ops.c:221: error: redefinition of ‘pm_clk_create’
include/linux/pm_clock.h:57: error: previous definition of ‘pm_clk_create’ was here
drivers/base/power/clock_ops.c:234: error: redefinition of ‘pm_clk_destroy’
include/linux/pm_clock.h:61: error: previous definition of ‘pm_clk_destroy’ was here
drivers/base/power/clock_ops.c: In function ‘pm_clk_destroy’:
drivers/base/power/clock_ops.c:246: error: ‘struct pm_subsys_data’ has no member named ‘clock_list’
drivers/base/power/clock_ops.c:246: error: ‘struct pm_subsys_data’ has no member named ‘clock_list’
drivers/base/power/clock_ops.c: At top level:
drivers/base/power/clock_ops.c:263: error: expected identifier or ‘(’ before ‘void’
drivers/base/power/clock_ops.c:263: error: expected ‘)’ before numeric constant
drivers/base/power/clock_ops.c:293: error: expected identifier or ‘(’ before ‘void’
drivers/base/power/clock_ops.c:293: error: expected ‘)’ before numeric constant
drivers/base/power/clock_ops.c: In function ‘pm_clk_runtime_suspend’:
drivers/base/power/clock_ops.c:384: error: called object ‘0u’ is not a function
drivers/base/power/clock_ops.c: In function ‘pm_clk_runtime_resume’:
drivers/base/power/clock_ops.c:400: error: called object ‘0u’ is not a function
This happens because:
- drivers/base/power/clock_ops.c depends on CONFIG_HAVE_CLK,
- the failing code inside clock_ops.c additionally depends on
CONFIG_PM,
- the forward declarations and other definitions in <linux/pm_clock.h>
depend on CONFIG_PM_CLK,
- CONFIG_PM_CLK is defined as PM && HAVE_CLK in kernel/power/Kconfig,
but it is not included on all architectures.
Fix this by protecting the failing code inside clock_ops.c by
CONFIG_PM_CLK instead of CONFIG_PM, so it matches <linux/pm_clock.h>.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Clock references are on a per-user basis now, so they are not supposed
to be refcounted by itself anymore. Therefore multiple cascaded get and
put calls will fail.
When a clock reference gets passed into pm_clk_add_clk we can assume
that the pm clock handling will take control of the clock reference,
so after this functions returns the caller should've given up control
of that handle.
So remove the additional call to __clk_get() in __pm_clk_add().
The only current user of pm_clk_add_clk is drivers/clk/shmobile/clk-mstp.c
which already follows this paradigm by only getting the clock but not
puting it after passing the reference into pm_clk_add_clk.
In the error case the caller is expected to clean up the clock, as it
may very well try to do something different if pm_clk_add_clk() fails.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[add commit-message]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Static analysis by cppcheck found an issue that was recently introduced by
commit 471f7707b6 ("PM / clock_ops: make __pm_clk_enable more generic")
where a return status in ret was not being initialised and garbage
being returned when ce->status >= PCE_STATUS_ERROR.
The fact that ret is not being checked by the caller and that
ret is only used internally __pm_clk_enable() to check if clk_enable()
was OK means we can ignore returning it instead turn
__pm_clk_enable() into function with a void return.
Fixes: 471f7707b6 ("PM / clock_ops: make __pm_clk_enable more generic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the con_id of the acquired clock is printed for debugging
purposes. But in several cases, the con_id is NULL, which doesn't
provide much debugging information when printed. These cases are:
- When explicitly passing a NULL con_id (which means the first clock
tied to the device, if available),
- When not using pm_clk_add(), but pm_clk_add_clk() (which takes a
"struct clk *" directly).
Hence print the actual clock name in addition to (and not instead of;
thanks Grygorii Strashko!) the con_id.
Note that the clock name is not available with legacy clock frameworks,
and the hex pointer address will be printed instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the final iteration of commit 245bd6f6af ("PM / clock_ops: Add
pm_clk_add_clk()"), a refcount increment was added by Grygorii Strashko.
However, the accompanying IS_ERR() check operates on the wrong clock
pointer, which is always zero at this point, i.e. not an error.
This may lead to a NULL pointer dereference later, when __clk_get()
tries to dereference an error pointer.
Check the passed clock pointer instead to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 245bd6f6af ("PM / clock_ops: Add pm_clk_add_clk()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most users of PM clocks do the extact same things in the runtime
suspend/resume callbacks. Provide them USE_PM_CLK_RUNTIME_OPS so
as to avoid/remove boilerplate code.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch reduces the kernel size by removing error messages that duplicate
the normal OOM message.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr)
@@
identifier f,print,l;
expression e;
constant char[] c;
@@
e = \(kzalloc\|kmalloc\|devm_kzalloc\|devm_kmalloc\)(...);
if (e == NULL) {
<+...
- print(...,c,...);
... when any
(
goto l;
|
return ...;
)
...+> }
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM or even may be dropped entirely in some cases.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PM core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now there are two places in code which do the same things,
so allow __pm_clk_enable() to accept pointer on pm_clock_entry
structure as second parameter instead of pointer on clock and
remove duplicated code.
Also, updated function intended to be used by following patch.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The existing pm_clk_add() allows to pass a clock by con_id. However,
when referring to a specific clock from DT, no con_id is available.
Add pm_clk_add_clk(), which allows to specify the struct clk * directly.
The will will increment refcount on clock pointer, so the caller has
to use clk_put() on clock pointer when done.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Unlike the clocks management code for runtime PM, the code used for
system suspend does not check the pm_clock_entry.status field.
If pm_clk_acquire() failed, ce->status will be PCE_STATUS_ERROR, and
ce->clk will be a negative error code (e.g. 0xfffffffe = -2 = -ENOENT).
Depending on the clock implementation, suspend or resume may crash with:
Unable to handle kernel NULL pointer dereference at virtual address 00000026
(CCF clk_disable() has an IS_ERR_OR_NULL() check, while CCF clk_enable()
only has a NULL check; pre-CCF implementations may behave differently)
While just checking for PCE_STATUS_ERROR would be sufficient, it doesn't
hurt to use the same state machine as is done for runtime PM, as this
makes the two versions more similar, and eligible for a future
consolidation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If clk_enable() fails, then print a message so that the user can see
what is happening instead of silently failing to enable the clock.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The clk_enable() call in the pm_clk_resume() call returns an error
that is not being checked. If clk_enable() fails then we should
not set the state of the clock to PCE_STATUS_ENABLED.
Note, the issue of warning the user if this fails has not been
addressed in this patch as this is not the only place the driver
calls clk_enable().
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The drivers/base/power/clock_ops.c file is causing warnings from
the clock driver (as shown below) due to failing to do a clk_prepare()
call before enabling a clock. It also fails to check the balance of
prepare/unprepare as __pm_clk_remove() do clk_disable_unprepare() call.
This bug has probably been in since commit b2476490e ("clk: introduce
the common clock framework") as the warning was part of the original
commit. It is strange that it has not been noticed (although this has
also been coupled with a failure for certain SH builds to not build the
necessary glue to use this method of controlling the clocks).
In summary, this is probably needed in several stable branches but need
advice on which ones.
On the Renesas Lager board, this causes numerous warnings of the following
and even worse the clock system will not enable clocks, causing drivers
that are in development to fail to work:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:883 __clk_enable+0x2c/0xa0()
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When PM runtime is enabled in DaVinci and the machine migrates to
common clk framework, the clk_enable() gets called without
clk_prepare(). This patch is to fix this issue so that PM run
time can inter work with common clk framework.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commits 1d5fcfec22 (PM / Domains: Add device domain data reference
counter) and 62d4490294 (PM / Domains: Allow device callbacks to be
added at any time) added checks for the return value of
dev_pm_get_subsys_data(), but those checks were incorrect, because
that function returned 1 on success in some cases.
Since all of the existing users of dev_pm_get_subsys_data() don't use
the positive value returned by it on success, change its definition
so that it always returns 0 when successful.
Reported-by: Heiko Stübner <heiko@sntech.de>
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
For files that are actively using linux/device.h, make sure
that they call it out. This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.
Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered. This ensures we don't introduce
build regressions into the git history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Refrain from running clk_disable() on clocks that
have not been enabled. A typical case when this can
happen is during Suspend-to-RAM for devices that have
no driver associated with them. In such case the clock
may be in default ACQUIRED state.
Without this patch the sh7372 Mackerel board crashes
in __clk_disable() during Suspend-to-RAM with:
"Trying to disable clock 0xdeadbeef with 0 usecount"
This happens for the CEU device which is added during
boot. The test case has no CEU driver included in the
kernel configuration. Needed for v3.2-rc1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since kfree() checks it its argument is not NULL, it is not necessary
to duplicate this check in __pm_clk_remove().
[rjw: Added the changelog.]
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Merge commit e8b364b88c
(PM / Clocks: Do not acquire a mutex under a spinlock) fixing
a regression in drivers/base/power/clock_ops.c.
Conflicts:
drivers/base/power/clock_ops.c
Commit b7ab83e (PM: Use spinlock instead of mutex in clock
management functions) introduced a regression causing clocks_mutex
to be acquired under a spinlock. This happens because
pm_clk_suspend() and pm_clk_resume() call pm_clk_acquire() under
pcd->lock, but pm_clk_acquire() executes clk_get() which causes
clocks_mutex to be acquired. Similarly, __pm_clk_remove(),
executed under pcd->lock, calls clk_put(), which also causes
clocks_mutex to be acquired.
To fix those problems make pm_clk_add() call pm_clk_acquire(), so
that pm_clk_suspend() and pm_clk_resume() don't have to do that.
Change pm_clk_remove() and pm_clk_destroy() to separate
modifications of the pcd->clock_list list from the actual removal of
PM clock entry objects done by __pm_clk_remove().
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the PM clock management code in drivers/base/power/clock_ops.c
is used for both runtime PM and system suspend/hibernation, the
definitions of data structures and headers related to it should not
be located in include/linux/pm_rumtime.h. Move them to a separate
header file.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since the power.subsys_data device field will be used by multiple
filesystems, introduce a reference counting mechanism for it to avoid
freeing it prematurely or changing its value at a wrong time.
Make the PM clocks management code that currently is the only user of
power.subsys_data use the new reference counting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce struct pm_subsys_data that may be subclassed by subsystems
to store subsystem-specific information related to the device. Move
the clock management fields accessed through the power.subsys_data
pointer in struct device to the new strucutre.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The lock member of struct pm_clk_data is of type struct mutex,
which is a problem, because the suspend and resume routines
defined in drivers/base/power/clock_ops.c cannot be executed
with interrupts disabled for this reason. Modify
struct pm_clk_data so that its lock member is a spinlock.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The common PM clock management functions may be used for system
suspend/resume as well as for runtime PM, so rename them
accordingly. Modify kerneldoc comments describing these functions
and kernel messages printed by them, so that they refer to power
management in general rather that to runtime PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
The common clocks management code in drivers/base/power/clock_ops.c
is going to be used during system-wide power transitions as well as
for runtime PM, so it shouldn't depend on CONFIG_PM_RUNTIME.
However, the suspend/resume functions provided by it for
CONFIG_PM_RUNTIME unset, to be used during system-wide power
transitions, should not behave in the same way as their counterparts
defined for CONFIG_PM_RUNTIME set, because in that case the clocks
are managed differently at run time.
The names of the functions still contain the word "runtime" after
this change, but that is going to be modified by a separate patch
later.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
The naming convention used by commit 7538e3db6e015e890825fbd9f86599b
(PM: Add support for device power domains), which introduced the
struct dev_power_domain type for representing device power domains,
evidently confuses some developers who tend to think that objects
of this type must correspond to "power domains" as defined by
hardware, which is not the case. Namely, at the kernel level, a
struct dev_power_domain object can represent arbitrary set of devices
that are mutually dependent power management-wise and need not belong
to one hardware power domain. To avoid that confusion, rename struct
dev_power_domain to struct dev_pm_domain and rename the related
pointers in struct device and struct pm_clk_notifier_block from
pwr_domain to pm_domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
Commit 85eb8c8d0b (PM / Runtime:
Generic clock manipulation rountines for runtime PM (v6)) converted
the shmobile platform to using generic code for runtime PM clock
management, but it changed the behavior for CONFIG_PM_RUNTIME unset
incorrectly.
Specifically, for CONFIG_PM_RUNTIME unset pm_runtime_clk_notify()
should enable clocks for action equal to BUS_NOTIFY_BIND_DRIVER and
it should disable them for action equal to BUS_NOTIFY_UNBOUND_DRIVER
(instead of BUS_NOTIFY_ADD_DEVICE and BUS_NOTIFY_DEL_DEVICE,
respectively). Make this function behave as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The loops over connection ID strings in pm_runtime_clk_notify()
should actually iterate over the strings and not over the elements
of the first of them, so make them behave as appropriate.
This fixes a regression introduced by commit 600b776eb3
(OMAP1 / PM: Use generic clock manipulation routines for runtime PM).
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Many different platforms and subsystems may want to disable device
clocks during suspend and enable them during resume which is going to
be done in a very similar way in all those cases. For this reason,
provide generic routines for the manipulation of device clocks during
suspend and resume.
Convert the ARM shmobile platform to using the new routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
