commit 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback") skips data resets during tuning operation. Because of this,
a data error or data finish interrupt might still arrive after a command
error has been handled and the mrq ended. This ends up with a "mmc0: Got
data interrupt 0x00000002 even though no data operation was in progress"
error message.
Fix this by adding a platform specific callback for sdhci_irq. Mark the
mrq as a failure but wait for a data interrupt instead of calling
finish_mrq().
Fixes: 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The alcor driver is setting up data transfer and submitting the associated
MMC command at the same time. While this works most of the time, it
occasionally causes problems upon write.
In the working case, after setting up the data transfer and submitting
the MMC command, an interrupt comes in a moment later with CMD_END and
WRITE_BUF_RDY bits set. The data transfer then happens without problem.
However, on occasion, the interrupt that arrives at that point only
has WRITE_BUF_RDY set. The hardware notifies that it's ready to write
data, but the associated MMC command is still running. Regardless, the
driver was proceeding to write data immediately, and that would then cause
another interrupt indicating data CRC error, and the write would fail.
Additionally, the transfer setup function alcor_trigger_data_transfer()
was being called 3 times for each write operation, which was confusing
and may be contributing to this issue.
Solve this by tweaking the driver behaviour to follow the sequence observed
in the original ampe_stor vendor driver:
1. When starting request handling, write 0 to DATA_XFER_CTRL
2. Submit the command
3. Wait for CMD_END interrupt and then trigger data transfer
4. For the PIO case, trigger the next step of the data transfer only
upon the following DATA_END interrupt, which occurs after the block has
been written.
I confirmed that the read path still works (DMA & PIO) and also now
presents more consistency with the operations performed by ampe_stor.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R-Car Gen2 has two different SDHI incarnations in the same chip. The
older one does not support the recently introduced 32 bit register
access to the block count register. Make sure we use this feature only
after the first known version.
Thanks to the Renesas Testing team for this bug report!
Fixes: 5603731a15 ("mmc: tmio: fix access width of Block Count Register")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Phong Hoang <phong.hoang.wz@renesas.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting max_blk_count to 1 here was causing the mmc block layer
to always use the MMC_READ_SINGLE_BLOCK command here, which the
driver does not DMA-accelerate.
Drop the max_blk_ settings here. The mmc host defaults suffice,
along with the max_segs and max_seg_size settings, which I have
now documented in more detail.
Now each MMC command reads 4 512-byte blocks, using DMA instead of
PIO. On my SD card, this increases read performance (measured with dd)
from 167kb/sec to 4.6mb/sec.
Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 6d5cd068ee ("mmc: sdhci: use WP GPIO in
sdhci_check_ro()") and commit 39ee32ce48 ("mmc: sdhci-omap: drop
->get_ro() implementation"), sdhci-omap relied on SDHCI_PRESENT_STATE
to check if the card is read-only, if wp-gpios is not populated
in device tree. However SDHCI_PRESENT_STATE in sdhci-omap does not have
correct read-only state.
sdhci-omap can be used by platforms with both micro SD slot and standard
SD slot with physical write protect pin (using GPIO). Set caps2 to
MMC_CAP2_NO_WRITE_PROTECT based on if wp-gpios property is populated or
not.
This fix is required since existing device-tree node doesn't have
"disable-wp" property and to preserve old-dt compatibility.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Fixes: 39ee32ce48 ("mmc: sdhci-omap: drop ->get_ro() implementation")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Building with clang finds a mistaken __init tag:
WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host()
The function davinci_mmcsd_probe() references
the function __init init_mmcsd_host().
This is often because davinci_mmcsd_probe lacks a __init
annotation or the annotation of init_mmcsd_host is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clang points out several instances of mismatched types in this drivers,
all coming from a single declaration:
drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to
different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion]
direction = DMA_DEV_TO_MEM;
~ ^~~~~~~~~~~~~~
drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to
different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion]
tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction,
The behavior is correct, so this must be a simply typo from
dma_data_direction and dma_transfer_direction being similarly named
types with a similar purpose.
Fixes: 6464b71409 ("mmc: pxamci: switch over to dmaengine use")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAlx63XIQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpp2vEACfrrQsap7R+Av28mmXpmXi2FPa3g5Tev1t
yYjK2qHvhlMZjPTYw3hCmbYdDDczlF7PEgSE2x2DjdcsYapb8Fy1lZ2X16c7ztBR
HD/t9b5AVSQsczZzKgv3RqsNtTnjzS5V0A8XH8FAP2QRgiwDMwSN6G0FP0JBLbE/
ZgxQrH1Iy1F33Wz4hI3Z7dEghKPZrH1IlegkZCEu47q9SlWS76qUetSy2GEtchOl
3Lgu54mQZyVdI5/QZf9DyMDLF6dIz3tYU2qhuo01AHjGRCC72v86p8sIiXcUr94Q
8pbegJhJ/g8KBol9Qhv3+pWG/QUAZwi/ZwasTkK+MJ4klRXfOrznxPubW1z6t9Vn
QRo39Po5SqqP0QWAscDxCFjESIQlWlKa+LZurJL7DJDCUGrSgzTpnVwFqKwc5zTP
HJa5MT2tEeL2TfUYRYCfh0ZV0elINdHA1y1klDBh38drh4EWr2gW8xdseGYXqRjh
fLgEpoF7VQ8kTvxKN+E4jZXkcZmoLmefp0ZyAbblS6IawpPVC7kXM9Fdn2OU8f2c
fjVjvSiqxfeN6dnpfeLDRbbN9894HwgP/LPropJOQ7KmjCorQq5zMDkAvoh3tElq
qwluRqdBJpWT/F05KweY+XVW8OawIycmUWqt6JrVNoIDAK31auHQv47kR0VA4OvE
DRVVhYpocw==
=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
The original purpose of the code I fix is to replace max_discard with
max_trim if max_trim is less than max_discard. When max_discard is 0
we should replace max_discard with max_trim as well, because
max_discard equals 0 happens only when the max_do_calc_max_discard
process is overflowed, so if mmc_can_trim(card) is true, max_discard
should be replaced by an available max_trim.
However, in the original code, there are two lines of code interfere
the right process.
1) if (max_discard && mmc_can_trim(card))
when max_discard is 0, it skips the process checking if max_discard
needs to be replaced with max_trim.
2) if (max_trim < max_discard)
the condition is false when max_discard is 0. it also skips the process
that replaces max_discard with max_trim, in fact, we should replace the
0-valued max_discard with max_trim.
Signed-off-by: Jiong Wu <Lohengrin1024@gmail.com>
Fixes: b305882fbc (mmc: core: optimize mmc_calc_max_discard)
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card was removed in suspended state and a new one was inserted,
print a debug log when the check detects that it's not the old card.
Signed-off-by: hongjiefang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.
A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register. If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.
Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.
One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the response type of CMD6 is R1B, when the first CMD6 gets response
CRC error, do retry may get timeout error due to card may still in
busy state, which cause this retry make no sense.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 72a5af554d ("mmc: core: Add support for handling CQE requests")
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user of mmc_align_data_size() is sdio_align_size(), which is
called from SDIO func drivers to let them distinguish, how to optimally
allocate data buffers.
Let's move mmc_align_data_size() close to the SDIO code as to make it
static, rename it to _sdio_align_size() and simplify its definition, all
with the purpose of clarifying that this is SDIO specific.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
The call tree looks something like this:
mmc_spi_probe
mmc_add_host
mmc_start_host
_mmc_detect_change
mmc_schedule_delayed_work(&host->detect, 0)
mmc_rescan
host->bus_ops->detect(host)
mmc_detect
_mmc_detect_card_removed
host->ops->get_cd(host)
mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set)
mmc_gpiod_request_cd
ctx->cd_gpio = desc
To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ
is registered.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC OF parsing functions, which parses various host DT properties, should
stay close to each other. Therefore, let's move mmc_of_parse_voltage()
close to mmc_of_parse() into host.c.
Additionally, there is no reason to build the code only when CONFIG_OF is
set, as there should be stub functions for the OF helpers that is being
used, so let's drop this condition as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only left user of mmc_regulator_get_ocrmask() is the mmc core itself.
Therefore, let's drop the export and turn it into static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc regulator helper functions, are placed in the extensive core.c
file. In a step towards trying to create a better structure of files,
avoiding too many lines of code per file, let's move these helpers to a new
file, regulator.c.
Moreover, this within this context it makes sense to also drop the export
of mmc_vddrange_to_ocrmask(), but instead let's make it internal to the mmc
core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's drop the open-coding of the parsing of the "voltage-ranges" DT
property and convert to use the common mmc_of_parse_voltage() API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All callers of mmc_wait_for_app_cmd() set the retries in-parameter to
MMC_CMD_RETRIES. This is silly, so let's just drop the in-parameter
altogether, as to simplify the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_wait_for_app_cmd() is an internal function for sd_ops.c, thus let's
drop the unnecessary export and turn it into static function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SCC is used for SDR104/HS200/HS400. We need to change SCC_DT2FF
according to the mode. If it is inappropriate, CRC error tends to occur.
This adds variable "tap_hs400" for HS400 mode and configures SCC_DT2FF
as needed.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased to upstream and updated commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a
data transfer request, either because of using the open-ended transmission
type or because of receiving an error during a pre-defined data transfer,
isn't sufficient for the STM32 sdmmc variant. More precisely, this variant
needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for
all failing ADTC commands.
Support this, by adding a struct mmc_command inside the struct mmci_host
and initialize it to a CMD12 during ->probe(). Let's also add checks for
the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to
postpone the calls to mmci_request_end(), but instead send the CMD12.
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
according to what the compiler looks for, where we are expecting to fall
through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI core is know properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-tegra code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI core is now properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-omap code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though SDHCI controllers may have a dedicated WP pin that can be
queried using the SDHCI_PRESENT_STATE register, some platforms may
chose to use a separate regular GPIO to route the WP signal. Such a
GPIO is typically represented using the wp-gpios property in the
Device Tree.
Unfortunately, the current sdhci_check_ro() function does not make use
of such GPIO when available: it either uses a host controller specific
->get_ro() operation, or uses the SDHCI_PRESENT_STATE. Several host
controller specific ->get_ro() functions are implemented just to check
a WP GPIO state.
Instead of pushing this to more controller-specific implementations,
let's handle this in the core SDHCI code, just like it is already done
for the CD GPIO in sdhci_get_cd().
The below patch simply changes sdhci_check_ro() to use the value of
the WP GPIO if available.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The WMT SDMMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> so drop this surplus include.
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Sunxi MMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: cenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI PXAv2 driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> so drop this surplus include.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI BCM Kona driver uses slot GPIO helpers and does not
make any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MXS-MMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MXCMMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Jun Qian <hangdianqj@163.com>
Cc: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is an if block that is not indented, fix this. Also add a
break statement on the default case to clean up a cppcheck warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD specs version 4.x and 5.x have a dedicated slices in the SCR register.
Higher versions will rely on a combination of the existing fields.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In MMC, the discard arg is a read-only ext_csd parameter - set it once
on card init. To be consistent, do that for SD as well even though its
discard arg is always 0x0.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.
This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.
This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver uses a pointer to get from the private
bcm2835_host structure to the generic mmc_host structure. However the
latter is always immediately preceding the former in memory, so compute
its address with a subtraction (which is cheaper than a dereference) and
drop the superfluous pointer.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Alexander Graf <agraf@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
