The core clock and M2MC clocks are shared between some devices (Unicam
controllers and the HVS, and the HDMI controllers, respectively) that
will have various, varying, requirements depending on their current work
load.
Since those loads can require a fairly high clock rate in extreme
conditions (up to ~600MHz), we can end up running those clocks at their
maximum frequency even though we no longer require such a high rate.
Fortunately, those devices don't require an exact rate but a minimum
rate, and all the drivers are using clk_set_min_rate. Thus, we can just
rely on the fact that the clk_request minimum (which is the aggregated
minimum of all the clock users) is what we want at all times.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220225143534.405820-11-maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The M2MC clock provides the state machine clock for both HDMI
controllers.
However, if no HDMI monitor is plugged in at boot, its clock rate will
be left at 0 by the firmware and will make any register access end up in
a CPU stall, even though the clock was enabled.
We had some code in the HDMI controller to deal with this before, but it
makes more sense to have it in the clock driver. Move it there.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220225143534.405820-10-maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We only export a bunch of firmware clocks, and some of them require
special treatment.
This has been do so far using some tests on the clock id in various
places, but this is fairly hard to extend and doesn't scale very well.
Since we'll need some more cases in the next patches, let's switch to a
variant structure that defines the behaviour we need to have for a given
clock.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220225143534.405820-9-maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
drivers/clk/bcm/clk-raspberrypi.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
To use QHD or higher, we need to modify the pixel_bvb_clk value. So
add register to control this clock.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Link: https://lore.kernel.org/r/20200901040759.29992-2-hoegeun.kwon@samsung.com
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CPU clock has had so far a bunch of quirks to expose the clock tree
properly, but since we reverted to exposing them through the MMIO driver,
we can remove that code from the firmware driver.
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/acdf820c2f78a25dd7480a0c018b8b387acd013e.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We've registered the firmware clocks using their ID as name, but it's much
more convenient to register them using their proper name. Since the
firmware doesn't provide it, we have to duplicate it.
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/a52a5f5768cd33716cdd35237c6613f26ad75013.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The RaspberryPi4 firmware actually exposes more clocks than are currently
handled by the driver and we will need to change some of them directly
based on the pixel rate for the display related clocks, or the load for the
GPU.
Since the firmware implements DVFS, this rate change can have a number of
side-effects, including adjusting the various PLL voltages or the PLL
parents. The firmware also implements thermal throttling, so even some
thermal pressure can change those parameters behind Linux back.
DVFS is currently implemented on the arm, core, h264, v3d, isp and hevc
clocks, so updating any of them using the MMIO driver (and thus behind the
firmware's back) can lead to troubles, the arm clock obviously being the
most problematic.
In order to make Linux play as nice as possible with those constraints, it
makes sense to rely on the firmware clocks as much as possible. However,
the firmware doesn't seem to provide some equivalents to their MMIO
counterparts, so we can't really replace that driver entirely.
Fortunately, the firmware has an interface to discover the clocks it
exposes.
Let's use it to discover, register the clocks in the clocks framework and
then expose them through the device tree for consumers to use them.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/438d73962741a8c5f7c689319b7443b930a87fde.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
While the firmware allows us to discover the available clocks, we need to
discriminate those clocks to only register the ones meaningful to Linux.
The firmware also doesn't provide a clock name, so having a list of the ID
will help us to give clocks a proper name later on.
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/4738f77ee7de9b48a3bb1c558ead958d0cc064d9.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For the upcoming registration of the clocks provided by the firmware, make
sure it's exposed to the device tree providers.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/4d8dbe4aaae98b3d3812ad7c3dba53d645cadbaf.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The raspberrypi_register_pllb has been returning an integer so far to
notify whether the functions has exited successfully or not.
However, the OF provider functions in the clock framework require access to
the clk_hw structure so that we can expose those clocks to device tree
consumers.
Since we'll want that for the future clocks, let's return a clk_hw pointer
instead of the return code.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/97218559db643e62fdd2b5e3046a2a05b8c2e769.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The driver only supports the pllb for now and all the clock framework hooks
are a mix of the generic firmware interface and the specifics of the pllb.
Since we will support more clocks in the future let's split the generic and
specific hooks
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/fdc21962fdc7de5c46232f198672d5d5c868ec74.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The raspberrypi_fw_pll_is_on function doesn't only apply to PLL
registered in the driver, but any clock exposed by the firmware.
Since we also implement the is_prepared hook, make the function
consistent with the other function names.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/ac93cc4e245316bb7e7426ac5ab0de8f3d919731.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The raspberry_clock_property only takes the clock ID as an argument, but
now that we have a clock data structure it makes more sense to just pass
that structure instead.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/d7a3b4df3ca23feb6e0d9c7ae2d232bfb913f926.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The driver has really only supported one clock so far and has hardcoded the
ID used in communications with the firmware in all the functions
implementing the clock framework hooks. Let's store that in the clock data
structure so that we can support more clocks later on.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/e23c37961b97b027e21efa3b818578970f88527a.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
So far the driver has really only been providing a single clock, and stored
both the data associated to that clock in particular with the data
associated to the "controller".
Since we will change that in the future, let's decouple the clock data from
the provider data.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/ee7f508db226214fab4add7f93a351f4137c86a1.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The raspberrypi firmware clock driver has a min_rate / max_rate clamping by
storing the info it needs in a private structure.
However, the CCF already provides such a facility, so we can switch to it
to remove the boilerplate.
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/d4c53dab6de5d5f70743d9c139d0117589530e62.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clkdev lookup created for the cpufreq device is never removed if
there's an issue later in probe or at module removal time.
Let's convert to the managed variant of the clk_hw_register_clkdev function
to make sure it happens.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/075e2c6d315eccdaf8fb72b320712b86e6c25b22.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since we don't care about retrieving the clk_lookup structure pointer
returned by clkdev_hw_create, we can just use the clk_hw_register_clkdev
function.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/59f6208b6fe3367e735b0cca4f65c2c937639af9.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pllb_arm_lookup pointer in the struct raspberrypi_clk is not used for
anything but to store the returned pointer to clkdev_hw_create, and is not
used anywhere else in the driver.
Let's remove that global pointer from the structure.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/189407f54906d2b07c91de7a4eeb6d8c8934280f.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pllb_arm clock was created at probe time, but was never removed if
something went wrong later in probe, or if the driver was ever removed from
the system.
Now that we are using clk_hw_register(), we can just use its managed variant
to take care of that for us.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/34254ed1556614658e5dad5cca4cf4fe617df7fc.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pllb_arm clk_hw pointer in the raspberry_clk structure isn't used
anywhere but in the raspberrypi_register_pllb_arm.
Let's remove it, this will make our lives easier in future patches.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/842859cf1a77478620f45049178a588448202858.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pllb_arm clock is defined as a fixed factor clock with the pllb
clock as a parent. However, all its configuration is entirely static,
and thus we don't really need to call clk_hw_register_fixed_factor() but
can simply call clk_hw_register() with a static clk_fixed_factor
structure.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1146177664999eeda65856d28ce94025021dd85e.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Instead of declaring the clk_init_data and then calling memset on it, just
initialise properly.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/0342572daa561dc1bb4c9fd10641b2016493e32b.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The current firmware clock driver for the RaspberryPi can only be probed by
manually registering an associated platform_device.
While this works fine for cpufreq where the device gets attached a clkdev
lookup, it would be tedious to maintain a table of all the devices using
one of the clocks exposed by the firmware.
Since the DT on the other hand is the perfect place to store those
associations, make the firmware clocks driver probe-able through the device
tree so that we can represent it as a node.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/cb8203b862e386ac6c3df3eff0bb5a238b6ec97a.1592210452.git-series.maxime@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As 'clk-raspberrypi' depends on RPi's firmware interface, which might be
configured as a module, the cpu clock might not be available for the
cpufreq driver during it's init process. So we register the
'raspberrypi-cpufreq' platform device after the probe sequence succeeds.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Raspberry Pi's firmware offers an interface though which update it's
clock's frequencies. This is specially useful in order to change the CPU
clock (pllb_arm) which is 'owned' by the firmware and we're unable to
scale using the register interface provided by clk-bcm2835.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
