The WDT on RZ/V2M devices is basically the same as RZ/G2L, but without
the parity error registers. This means the driver has to reset the
hardware plus set the minimum timeout in order to do a restart and has
a single interrupt.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220823093233.8577-3-phil.edworthy@renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This code assumes that platform_get_irq() function returns zero on
failure. In fact, platform_get_irq() never returns zero. It returns
negative error codes or positive non-zero values on success.
Fixes: eca10ae600 ("watchdog: add driver for Cortina Gemini watchdog")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/YvTgRk/ABp62/hNA@kili
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Implement ftwdt010_wdt_restart(). It enables watchdog with timeout = 0
and disabled IRQ. Since it needs code similar to ftwdt010_wdt_start(),
add a new function ftwdt010_enable() and move common code there.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220829090436.452742-1-saproj@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The status bit in the status and control register can tell us whether
the last reboot was caused by the watchdog. Make sure to take that into
the bootstatus before clearing it.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220824152448.7736-1-henning.schild@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If the output driving type is push-pull mode, the output
polarity should be selected in advance. Otherwise, an unexpected
value will be output at the moment of changing to push-pull mode.
Thus, output polarity, WDT18[31], must be configured before
changing driving type, WDT18[30].
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bonnie Lo <Bonnie_Lo@wiwynn.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220819094905.1962513-1-chin-ting_kuo@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Enable HP_WATCHDOG for ARM64 systems.
HPWDT_NMI_DECODING requires X86 as NMI handlers are X86 specific.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220820202821.1263837-3-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fixes: d48b0e1737 ("x86, nmi, drivers: Fix nmi splitup build bug")
Arm64 does not support NMI and has no <asm/nmi.h>.
Include <asm/nmi.h> only if CONFIG_HPWDT_NMI_DECODING is defined to
avoid build failure on non-existent header file on Arm64.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220820202821.1263837-2-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The wdat_wdt driver is misusing the min_hw_heartbeat_ms field. This
field should only be used when the hardware watchdog device should not
be pinged more frequently than a specific period. The ACPI WDAT
"Minimum Count" field, on the other hand, specifies the minimum
timeout value that can be set. This corresponds to the min_timeout
field in Linux's watchdog infrastructure.
Setting min_hw_heartbeat_ms instead can cause pings to the hardware
to be delayed when there is no reason for that, eventually leading to
unexpected firing of the watchdog timer (and thus unexpected reboot).
Since commit 6d72c7ac9f ("watchdog: wdat_wdt: Using the existing
function to check parameter timeout"), min_timeout is being set too,
but to the arbitrary value of 1 second, which doesn't make sense and
allows setting timeout values lower that the ACPI WDAT "Minimum
Count" field.
I'm also changing max_hw_heartbeat_ms to max_timeout for symmetry,
although the use of this one isn't fundamentally wrong, but there is
also no reason to enable the software-driven ping mechanism for the
wdat_wdt driver.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 058dfc7670 ("ACPI / watchdog: Add support for WDAT hardware watchdog")
Fixes: 6d72c7ac9f ("watchdog: wdat_wdt: Using the existing function to check parameter timeout")
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Liu Xinpeng <liuxp11@chinatelecom.cn>
Link: https://lore.kernel.org/r/20220823154713.023ee771@endymion.delvare
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
I would like to stop exporting OF-specific devm_gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
fwnode property API.
While at it, switch the rest of the calls to read properties in
bd9576_wdt_probe() to the generic device property API as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-10-b29adfb27a6c@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmLvs58ACgkQ+iyteGJfRso79wCeNvcoRsn0oAyjuWaElPp0cTJq
5zwAni7zKz4VAOPaC9u5gNQoaj5+ZeKK
=XMqt
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.20-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add RTL9310 support
- sp805_wdt: add arm cmsdk apb wdt support
- Remove #ifdef guards for PM related functions for several watchdog
device drivers
- pm8916_wdt reboot improvements
- Several other fixes and improvements
* tag 'linux-watchdog-5.20-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
watchdog: armada_37xx_wdt: check the return value of devm_ioremap() in armada_37xx_wdt_probe()
watchdog: dw_wdt: Fix comment typo
watchdog: Fix comment typo
dt-bindings: watchdog: Add fsl,scu-wdt yaml file
watchdog:Fix typo in comment
watchdog: pm8916_wdt: Handle watchdog enabled by bootloader
watchdog: pm8916_wdt: Report reboot reason
watchdog: pm8916_wdt: Avoid read of write-only PET register
watchdog: wdat_wdt: Remove #ifdef guards for PM related functions
watchdog: tegra_wdt: Remove #ifdef guards for PM related functions
watchdog: st_lpc_wdt: Remove #ifdef guards for PM related functions
watchdog: sama5d4_wdt: Remove #ifdef guards for PM related functions
watchdog: s3c2410_wdt: Remove #ifdef guards for PM related functions
watchdog: mtk_wdt: Remove #ifdef guards for PM related functions
watchdog: dw_wdt: Remove #ifdef guards for PM related functions
watchdog: bcm7038_wdt: Remove #ifdef guards for PM related functions
watchdog: realtek-otto: add RTL9310 support
dt-bindings: watchdog: realtek,otto-wdt: add RTL9310
watchdog: sp805_wdt: add arm cmsdk apb wdt support
watchdog: sp5100_tco: Fix a memory leak of EFCH MMIO resource
...
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
Highlights:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop Studio
- thinkpad_acpi: AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
The following is an automated git shortlog grouped by driver:
ACPI:
- video: Fix acpi_video_handles_brightness_key_presses()
- video: Change how we determine if brightness key-presses are handled
Documentation/ABI:
- Add new attributes for mlxreg-io sysfs interfaces
- mlxreg-io: Fix contact info
Drop the PMC_ATOM Kconfig option:
- Drop the PMC_ATOM Kconfig option
EDAC, pnd2:
- convert to use common P2SB accessor
- Use proper I/O accessors and address space annotation
HID:
- surface-hid: Add support for hot-removal
ISST:
- PUNIT device mapping with Sub-NUMA clustering
Kconfig:
- Remove unnecessary "if X86"
MAINTAINERS:
- repair file entry in MICROSOFT SURFACE AGGREGATOR TABLET-MODE SWITCH
Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans:
- Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans
Move AMD platform drivers to separate directory:
- Move AMD platform drivers to separate directory
acer-wmi:
- Use backlight helper
acer_wmi:
- Cleanup Kconfig selects
apple-gmux:
- Use backlight helper
asus-wmi:
- Add mic-mute LED classdev support
- Add key mappings
compal-laptop:
- Use backlight helper
efi:
- Fix efi_power_off() not being run before acpi_power_off() when necessary
gigabyte-wmi:
- add support for B660I AORUS PRO DDR4
hp-wmi:
- Ignore Sanitization Mode event
i2c:
- i801: convert to use common P2SB accessor
ideapad-laptop:
- Add Ideapad 5 15ITL05 to ideapad_dytc_v4_allow_table[]
- Add allow_v4_dytc module parameter
intel/pmc:
- Add Alder Lake N support to PMC core driver
intel_atomisp2_led:
- Also turn off the always-on camera LED on the Asus T100TAF
leds:
- simatic-ipc-leds-gpio: Add GPIO version of Siemens driver
- simatic-ipc-leds: Convert to use P2SB accessor
mfd:
- lpc_ich: Add support for pinctrl in non-ACPI system
- lpc_ich: Switch to generic p2sb_bar()
- lpc_ich: Factor out lpc_ich_enable_spi_write()
mlx-platform:
- Add COME board revision register
- Add support for new system XH3000
- Introduce support for COMe NVSwitch management module for Vulcan chassis
- Add support for systems equipped with two ASICs
- Add cosmetic changes for alignment
- Make activation of some drivers conditional
p2sb:
- Move out of X86_PLATFORM_DEVICES dependency
panasonic-laptop:
- Use acpi_video_get_backlight_type()
- filter out duplicate volume up/down/mute keypresses
- don't report duplicate brightness key-presses
- revert "Resolve hotkey double trigger bug"
- sort includes alphabetically
- de-obfuscate button codes
pinctrl:
- intel: Check against matching data instead of ACPI companion
platform/mellanox:
- mlxreg-lc: Fix error flow and extend verbosity
- mlxreg-io: Add locking for io operations
- nvsw-sn2201: fix error code in nvsw_sn2201_create_static_devices()
platform/olpc:
- Fix uninitialized data in debugfs write
platform/surface:
- gpe: Add support for 13" Intel version of Surface Laptop 4
- tabletsw: Fix __le32 integer access
- Update copyright year of various drivers
- aggregator: Move subsystem hub drivers to their own module
- aggregator: Move device registry helper functions to core module
- aggregator_registry: Add support for tablet mode switch on Surface Laptop Studio
- aggregator_registry: Add support for tablet mode switch on Surface Pro 8
- Add KIP/POS tablet-mode switch driver
- aggregator: Add helper macros for requests with argument and return value
- aggregator: Reserve more event- and target-categories
- avoid flush_scheduled_work() usage
- aggregator_registry: Add support for keyboard cover on Surface Pro 8
- aggregator_registry: Add KIP device hub
- aggregator_registry: Change device ID for base hub
- aggregator_registry: Generify subsystem hub functionality
- aggregator: Add comment for KIP subsystem category
- aggregator_registry: Use client device wrappers for notifier registration
- aggregator: Allow notifiers to avoid communication on unregistering
- aggregator: Allow devices to be marked as hot-removed
- aggregator: Allow is_ssam_device() to be used when CONFIG_SURFACE_AGGREGATOR_BUS is disabled
platform/x86/amd/pmc:
- Add new platform support
- Add new acpi id for PMC controller
platform/x86/dell:
- Kconfig: Remove unnecessary "depends on X86_PLATFORM_DEVICES"
platform/x86/intel:
- Add Primary to Sideband (P2SB) bridge support
platform/x86/intel/ifs:
- Mark as BROKEN
platform/x86/intel/pmt:
- telemetry: Fix fixed region handling
platform/x86/intel/vsec:
- Fix wrong type for local status variables
- Add PCI error recovery support to Intel PMT
- Add support for Raptor Lake
- Rework early hardware code
pmc_atom:
- Fix comment typo
- Match all Lex BayTrail boards with critclk_systems DMI table
power/supply:
- surface_battery: Use client device wrappers for notifier registration
- surface_charger: Use client device wrappers for notifier registration
serial-multi-instantiate:
- Sort ACPI IDs by HID
- Get rid of redundant 'else'
- Use while (i--) pattern to clean up
- Improve dev_err_probe() messaging
- Drop duplicate check
- Improve autodetection
simatic-ipc:
- drop custom P2SB bar code
sony-laptop:
- Remove useless comparisons in sony_pic_read_possible_resource()
system76_acpi:
- Use dev_get_drvdata
thinkpad_acpi:
- Enable AMT by default on supported systems
- Add support for hotkey 0x131a
- Add support for automatic mode transitions
- profile capabilities as integer
- do not use PSC mode on Intel platforms
- Fix a memory leak of EFCH MMIO resource
- Replace custom str_on_off() etc
- Sort headers for better maintenance
- Use backlight helper
tools/power/x86/intel-speed-select:
- Remove unneeded semicolon
- Fix off by one check
watchdog:
- simatic-ipc-wdt: convert to use P2SB accessor
x86-android-tablets:
- Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmLrndEUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zeMgf7BjSCz6ZA8SSY1i8QHDTvdjySihHJ
j07Gn3j1T/5G00R/r6viMDE4PxcYvMAPXjq3azepKQd8H5kGfE323SA6fgWFPAvi
P2OvEfvWfI5S8FYGYPBkNP2MjQ5MFe7qzLEh3+wQH0ocJ7WRCi457B4Xvtd2gWI3
dHj5gMSWC3O5xNa2S4Mg3dnD9uJlwhX+FNjWIuRy8eh5+DikgByyC4B+uW6WtO5e
t0rmIm6q5wUzB7dIetJLoAQwrcpYAOkK7L33G9h/7knWAfiJfklaKTbftnoxbDSv
iGWODkLDyob4C48DmVusS6WMEhPUzl/R33+tk6LjVt/YOYOP030EMtCECQ==
=Krhc
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop
Studio
- thinkpad_acpi:
- AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
* tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (105 commits)
platform/x86/intel/vsec: Fix wrong type for local status variables
platform/x86: p2sb: Move out of X86_PLATFORM_DEVICES dependency
platform/x86: pmc_atom: Fix comment typo
platform/surface: gpe: Add support for 13" Intel version of Surface Laptop 4
platform/olpc: Fix uninitialized data in debugfs write
platform/mellanox: mlxreg-lc: Fix error flow and extend verbosity
platform/x86: pmc_atom: Match all Lex BayTrail boards with critclk_systems DMI table
platform/x86: sony-laptop: Remove useless comparisons in sony_pic_read_possible_resource()
tools/power/x86/intel-speed-select: Remove unneeded semicolon
tools/power/x86/intel-speed-select: Fix off by one check
platform/surface: tabletsw: Fix __le32 integer access
Documentation/ABI: Add new attributes for mlxreg-io sysfs interfaces
Documentation/ABI: mlxreg-io: Fix contact info
platform/mellanox: mlxreg-io: Add locking for io operations
platform/x86: mlx-platform: Add COME board revision register
platform/x86: mlx-platform: Add support for new system XH3000
platform/x86: mlx-platform: Introduce support for COMe NVSwitch management module for Vulcan chassis
platform/x86: mlx-platform: Add support for systems equipped with two ASICs
platform/x86: mlx-platform: Add cosmetic changes for alignment
platform/x86: mlx-platform: Make activation of some drivers conditional
...
The function devm_ioremap() in armada_37xx_wdt_probe() can fail, so
its return value should be checked.
Fixes: 54e3d9b518 ("watchdog: Add support for Armada 37xx CPU watchdog")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Reviewed-by: Marek Beh=C3=BAn <kabel@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220722030938.2925156-1-williamsukatube@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The double `have' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220716041951.34714-1-wangborong@cdjrlc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The double `and' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220716041856.34449-1-wangborong@cdjrlc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The bootloader might already enable the watchdog to catch hangs
during the boot process. In that case the kernel needs to ping
the watchdog temporarily until userspace is fully started.
Add a check for this in the probe() function and set the WDOG_HW_RUNNING
flag to make the watchdog core handle this automatically.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220629084816.125515-4-stephan.gerhold@kernkonzept.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The PM8916 PMIC provides "power-off reason" (POFF_REASON) registers
to allow detecting why the board was powered off or rebooted. This
can be used to expose if a reset happened due to a watchdog timeout.
The watchdog API also provides status bits for overtemperature and
undervoltage which happen to be reported in the same PMIC register.
Make this information available as part of the watchdog device
so userspace can decide to handle the situation accordingly.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220629084816.125515-3-stephan.gerhold@kernkonzept.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
PMIC_WD_RESET_PET is a write-only register that is used to ping
the watchdog. It does not make sense to use read-modify-write
for it: a register read will never return anything but zero.
(And actually even if it did we would still want to write again
to ensure the watchdog is pinged.)
Reduce the overhead for the watchdog ping slightly by using
regmap_write() directly instead.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220629084816.125515-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new NOIRQ_SYSTEM_SLEEP_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-9-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
While at it, the functions tegra_wdt_runtime_{suspend,resume} were
renamed to tegra_wdt_{suspend,resume}, as they are *not* runtime-PM
callbacks, but standard system suspend/resume callbacks.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-8-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-7-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new LATE_SYSTEM_SLEEP_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-6-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-5-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-4-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-3-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to
handle the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards. Not using #ifdef guards means that the code is
always compiled independently of any Kconfig option, and thanks to that
bugs and regressions are easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220628193449.160585-2-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The RTL9310 SoC series has a watchdog timer identical to the already
supported SoCs. The peripheral is memory mapped at 0x18003260 and driven
by the Lexra bus clock.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/629e95e16c8dc812dc5a4ea34a2e2e1ff2faf88c.1656356377.git.sander@svanheule.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Support arm CMSDK ip apb watchdog device.
Description details of this device can be found in the
document DDI0479D_m_class_processor_system_r1p1_trm.pdf
on the arm's document web. Which periphid is 0x001bb824.
The registers are basically the same as the 805, just a
few more: Periphid4/5/6/7 with offset 0xFD0/0xFD4/0xFD8/0xFDC.
For the register description of arm,sp805, please refer
to the document DDI0270-arm-sp805.pdf.
Signed-off-by: Bing Fan <tombinfan@tencent.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1656037482-19505-1-git-send-email-hptsfb@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Unlike release_mem_region(), a call to release_resource() does not
free the resource, so it has to be freed explicitly to avoid a memory
leak.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 0578fff4aa ("Watchdog: sp5100_tco: Add initialization using EFCH MMIO")
Cc: Terry Bowman <terry.bowman@amd.com>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220621152840.420a0f4c@endymion.delvare
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
My Bootlin address is preferred from now on.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
https://lore.kernel.org/r20220603155727.1232061-6-luca@lucaceresoli.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 27e0fe00a5 ("watchdog: f71808e_wdt: refactor to platform device/driver pair")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
https://lore.kernel.org/r/20220526080303.1005063-1-jiasheng@iscas.ac.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
PAPR v2.12 defines a new hypercall, H_WATCHDOG. The hypercall permits
guest control of one or more virtual watchdog timers. The timers have
millisecond granularity. The guest is terminated when a timer
expires.
This patch adds a watchdog driver for these timers, "pseries-wdt".
pseries_wdt_probe() currently assumes the existence of only one
platform device and always assigns it watchdogNumber 1. If we ever
expose more than one timer to userspace we will need to devise a way
to assign a distinct watchdogNumber to each platform device at device
registration time.
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713202335.1217647-5-cheloha@linux.ibm.com
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
This is the second part of the general SoC updates, containing
everything that did not make it in the initial pull request,
or that came in as a bugfix later.
- Devicetree updates for SoCFPGA, ASPEED, AT91 and Rockchip, including
a new machine using an ASPEED BMC.
- More DT fixes from Krzysztof Kozlowski across platforms
- A new SoC platform for the GXP baseboard management controller,
used in current server products from HPE.
-----BEGIN PGP SIGNATURE-----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=2qok
-----END PGP SIGNATURE-----
Merge tag 'arm-late-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM SoC updates from Arnd Bergmann:
"This is the second part of the general SoC updates, containing
everything that did not make it in the initial pull request, or that
came in as a bugfix later.
- Devicetree updates for SoCFPGA, ASPEED, AT91 and Rockchip,
including a new machine using an ASPEED BMC.
- More DT fixes from Krzysztof Kozlowski across platforms
- A new SoC platform for the GXP baseboard management controller,
used in current server products from HPE"
* tag 'arm-late-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (56 commits)
ARM: configs: Enable more audio support for i.MX
tee: optee: Pass a pointer to virt_addr_valid()
arm64: dts: rockchip: rename Quartz64-A bluetooth gpios
arm64: dts: rockchip: add clocks property to cru node rk3368
arm64: dts: rockchip: add clocks property to cru node rk3308
arm64: dts: rockchip: add clocks to rk356x cru
ARM: dts: rockchip: add clocks property to cru node rk3228
ARM: dts: rockchip: add clocks property to cru node rk3036
ARM: dts: rockchip: add clocks property to cru node rk3066a/rk3188
ARM: dts: rockchip: add clocks property to cru node rk3288
ARM: dts: rockchip: Remove "amba" bus nodes from rv1108
ARM: dts: rockchip: add clocks property to cru node rv1108
arm64: dts: sprd: use new 'dma-channels' property
ARM: dts: da850: use new 'dma-channels' property
ARM: dts: pxa: use new 'dma-channels/requests' properties
soc: ixp4xx/qmgr: Fix unused match warning
ARM: ep93xx: Make ts72xx_register_flash() static
ARM: configs: enable support for Kontron KSwitch D10
ep93xx: clock: Do not return the address of the freed memory
arm64: dts: intel: add device tree for n6000
...
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in some error paths.
Fixes: bf90063999 ("watchdog: ts4800: add driver for TS-4800 watchdog")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220511114203.47420-1-linmq006@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This is a driver for the standard WDT on the RZ/N1 devices. This WDT has
very limited timeout capabilities. However, it can reset the device.
To do so, the corresponding bits in the SysCtrl RSTEN register need to
be enabled. This is not done by this driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220427135531.708279-3-jjhiblot@traphandler.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Test shows that wachdog still reboots machine after the module
is removed. Use watchdog_stop_on_unregister to stop the watchdog
on removing.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
eviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-4-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Executing reboot command several times on the machine "Dell
PowerEdge R740", UEFI security detection stopped machine
with the following prompt:
UEFI0082: The system was reset due to a timeout from the watchdog
timer. Check the System Event Log (SEL) or crash dumps from
Operating Sysstem to identify the source that triggered the
watchdog timer reset. Update the firmware or driver for the
identified device.
iDRAC has warning event: "The watchdog timer reset the system".
This patch fixes this issue by adding the reboot notifier.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-3-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If max_hw_heartbeat_ms is provided, the configured maximum timeout is not
limited by it. The limit check in this driver therefore doesn't make much
sense. Similar, the watchdog core ensures that minimum timeout limits are
met if min_hw_heartbeat_ms is set. Using watchdog_timeout_invalid() makes
more sense because it takes this into account.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-2-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
For power management, SET_NOIRQ_SYSTEM_SLEEP_PM_OPS defined for
CONFIG_PM_SLEEP, will point ->suspend_noirq, ->freeze_noirq and
->poweroff_noirq to the same function. Vice versa happens for
->resume_noirq, ->thaw_noirq and ->restore_noirq.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650967905-3199-1-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: 2d63908bdb ("watchdog: Add K3 RTI watchdog support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220412070824.23708-1-linmq006@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This ensures that the same value is read back as was eventually
programmed when using seconds as accuracy. Even then, comparing the more
precise heartbeat_ms against heartbeat in seconds will almost never
provide a match and will needlessly raise a warning. Fix by comparing
apples to apples.
Tested in combination with U-Boot as watchdog starter.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/6a4b54ac-9588-e172-c4c7-b91d524a851e@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Disable the watchdog if it is active while removing the module.
It is necessary in order to prevent a reset in case watchdog
hw was running before the removal.
Signed-off-by: Eliav Farber <farbere@amazon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220414054233.1357-2-farbere@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Optionally disable watchdog during suspend (if enabled) and re-enable
it upon resume.
This enables boards to sleep without being interrupted by the watchdog.
This patch is based on commit f6c98b0838 ("watchdog: da9062: add
power management ops") and commit 8541673d2a ("watchdog: da9062: fix
power management ops") and brings the same functionality to DA9063.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Adam Thomson <DLG-Adam.Thomson.Opensource@dm.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220422072713.3172345-2-primoz.fiser@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add support for the HPE GXP Watchdog. The GXP asic contains a full
complement of timers one of which is the watchdog timer. The watchdog
timer is 16 bit and has 10ms resolution. The watchdog is created as a
child device of timer since the same register range is used.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for set_timeout callback.
Once WDT is started, the WDT cycle setting register(WDTSET) can be updated
only after issuing a module reset. Otherwise, it will ignore the writes
and will hold the previous value. This patch updates the WDTSET register
if it is active.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220225175320.11041-8-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch uses the force reset(WDTRSTB) for triggering WDT reset for
restart callback. This method(ie, Generate Reset (WDTRSTB) Signal on
parity error)is faster compared to the overflow method for triggering
watchdog reset.
Overflow method:
reboot: Restarting system
Reboot failed -- System halted
NOTICE: BL2: v2.5(release):v2.5/rzg2l-1.00-27-gf48f1440c
Parity error method:
reboot: Restarting system
NOTICE: BL2: v2.5(release):v2.5/rzg2l-1.00-27-gf48f1440c
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220225175320.11041-7-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If reset_control_deassert() fails, then we won't be able to
access the device registers. Therefore check the return code of
reset_control_deassert() and bailout in case of error.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220225175320.11041-6-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Both rzg2l_wdt_probe() and rzg2l_wdt_start() calls reset_control_
deassert() which results in a reset control imbalance.
This patch fixes reset control imbalance by removing reset_control_
deassert() from rzg2l_wdt_start() and replaces reset_control_assert with
reset_control_reset in rzg2l_wdt_stop() as watchdog module can be stopped
only by a module reset. This change will allow us to restart WDT after
stop() by configuring WDT timeout and enable registers.
Fixes: 2cbc5cd0b5 ("watchdog: Add Watchdog Timer driver for RZ/G2L")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220225175320.11041-5-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Both rzg2l_wdt_probe() and rzg2l_wdt_start() calls pm_runtime_get() which
results in a usage counter imbalance. This patch fixes this issue by
removing pm_runtime_get() call from probe.
Fixes: 2cbc5cd0b5 ("watchdog: Add Watchdog Timer driver for RZ/G2L")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220225175320.11041-3-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The value of timer_cycle_us can be 0 due to 32bit overflow.
For eg:- If we assign the counter value "0xfff" for computing
maxval.
This patch fixes this issue by appending ULL to 1024, so that
it is promoted to 64bit.
This patch also fixes the warning message, 'watchdog: Invalid min and
max timeout values, resetting to 0!'.
Fixes: 2cbc5cd0b5 ("watchdog: Add Watchdog Timer driver for RZ/G2L")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220225175320.11041-2-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
A new "compatible" value has been added in the commit 17fffe91ba
("dt-bindings: watchdog: Add BCM6345 compatible to BCM7038 binding").
It's meant to be used for BCM63xx SoCs family but hardware block can be
programmed just like the 7038 one.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220216063408.23168-1-zajec5@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Rather than relying on machine specific headers to
pass down the reboot status and the register locations,
use resources and platform_data.
Aside from this, keep the changes to a minimum.
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: linux-watchdog@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmJF7qQACgkQ+iyteGJfRsowRQCeOfozOBwouAz4tVIERCaYgril
D6sAn34jNnuYybj4YtEIBRCHWfbG6GsQ
=oHoS
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.18-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add support for BCM4908
- renesas_wdt: add R-Car Gen4 support
- improve watchdog_dev function documentation
- sp5100_tco: replace the cd6h/cd7h port I/O with MMIO accesses during
initialization
- several other small improvements and fixes
* tag 'linux-watchdog-5.18-rc1' of git://www.linux-watchdog.org/linux-watchdog:
Watchdog: sp5100_tco: Enable Family 17h+ CPUs
Watchdog: sp5100_tco: Add initialization using EFCH MMIO
Watchdog: sp5100_tco: Refactor MMIO base address initialization
Watchdog: sp5100_tco: Move timer initialization into function
watchdog: ixp4xx: Implement restart
watchdog: orion_wdt: support pretimeout on Armada-XP
watchdog: allow building BCM7038_WDT for BCM4908
watchdog: renesas_wdt: Add R-Car Gen4 support
dt-bindings: watchdog: renesas-wdt: Document r8a779f0 support
watchdog: Improve watchdog_dev function documentation
watchdog: aspeed: add nowayout support
watchdog: rti-wdt: Add missing pm_runtime_disable() in probe function
watchdog: imx2_wdg: Alow ping on suspend
The driver currently uses a CPU family match of 17h to determine
EFCH_PM_DECODEEN_WDT_TMREN register support. This family check will not
support future AMD CPUs and instead will require driver updates to add
support.
Remove the family 17h family check and add a check for SMBus PCI
revision ID 0x51 or greater. The MMIO access method has been available
since at least SMBus controllers using PCI revision 0x51. This revision
check will support family 17h and future AMD processors including EFCH
functionality without requiring driver changes.
Co-developed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220202153525.1693378-5-terry.bowman@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
cd6h/cd7h port I/O can be disabled on recent AMD hardware. Read
accesses to disabled cd6h/cd7h port I/O will return F's and written
data is dropped. It is recommended to replace the cd6h/cd7h
port I/O with MMIO.
Co-developed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220202153525.1693378-4-terry.bowman@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Combine MMIO base address and alternate base address detection. Combine
based on layout type. This will simplify the function by eliminating
a switch case.
Move existing request/release code into functions. This currently only
supports port I/O request/release. The move into a separate function
will make it ready for adding MMIO region support.
Co-developed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220202153525.1693378-3-terry.bowman@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Refactor driver's timer initialization into new function. This is needed
inorder to support adding new device layouts while using common timer
initialization.
Co-developed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220202153525.1693378-2-terry.bowman@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Commit e07a4c79ca ("watchdog: orion_wdt: use timer1 as a pretimeout")
added support for a pretimeout on Armada-38x variants. Because the
Armada-XP variants use armada370_start/armada370_stop (due to missing an
explicit RSTOUT mask bit for the watchdog). Add the required pretimeout
support to armada370_start/armada370_stop for Armada-XP.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220211003257.2037332-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
BCM4908 is a SoCs family that shares a lot of hardware with BCM63xx
including the watchdog block. Allow building this driver for it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220209203202.26395-1-zajec5@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add the compatible string for the R-Car Gen4 family.
No further driver changes are needed.
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/cc395105e1d34aab2c076d368c0737833970b9d2.1642525158.git.geert+renesas@glider.be
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Adjust function comments to the kernel doc format. It
also adjusts some variable names and adds return values.
No functional change.
Changes from V1:
Change "Returns" to "Return:" (Randy Dunlap)
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/30378a03e9cd9b5f6e92ec9bf512edc38bad8627.1644589712.git.bristot@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add support for not stopping the watchdog
when the userspace application quits. At
closing of the device, the driver cannot
determine if this was a graceful closure
or if the app crashed. If the support
of nowayout on this driver, the system integrator
can select the behaviour by setting the kernel
config and enabling it.
Cc: Wim Van Sebroeck <wim@linux-watchdog.org> (maintainer:WATCHDOG DEVICE DRIVERS)
Cc: Guenter Roeck <linux@roeck-us.net> (maintainer:WATCHDOG DEVICE DRIVERS)
Cc: Joel Stanley <joel@jms.id.au> (supporter:ARM/ASPEED MACHINE SUPPORT)
Cc: Andrew Jeffery <andrew@aj.id.au> (reviewer:ARM/ASPEED MACHINE SUPPORT)
Cc: linux-watchdog@vger.kernel.org (open list:WATCHDOG DEVICE DRIVERS)
Cc: linux-arm-kernel@lists.infradead.org (moderated list:ARM/ASPEED MACHINE SUPPORT)
Cc: linux-aspeed@lists.ozlabs.org (moderated list:ARM/ASPEED MACHINE SUPPORT)
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Eduardo Valentin <evalenti@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220212021033.2344-1-eduval@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Fixes: 2d63908bdb ("watchdog: Add K3 RTI watchdog support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220105092114.23932-1-linmq006@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The i.MX watchdog cannot be disabled by software once it has been
enabled. This means that it can't be stopped before suspend.
For systems that enter low power mode this is fine, as the watchdog will
be automatically stopped by hardware in low power mode. Not all i.MX
platforms support low power mode in the mainline kernel. For example the
i.MX7D does not enter low power mode and so will be rebooted 2 minutes
after entering sleep states.
This patch introduces a device tree property "fsl,ping-during-suspend"
that can be used to enable ping on suspend support for these systems.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220127104739.312592-1-alistair@alistair23.me
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
- Add support for Maxim MAX77714 PMIC
- Remove Drivers
- Remove support for ST-Ericsson AB8500 DebugFS
- New Device Support
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
- New Functionality
- Add support for Reboot to Rockchip RK808
- Fix-ups
- Device Tree changes (inc. YAML conversion); silergy,sy7636a, maxim,max77843,
google,cros-ec, maxim,max14577, maxim,max77802,
maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576
-----BEGIN PGP SIGNATURE-----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=1xnI
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Maxim MAX77714 PMIC
Removed Drivers:
- Remove support for ST-Ericsson AB8500 DebugFS
New Device Support:
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
New Functionality:
- Add support for Reboot to Rockchip RK808
Fix-ups:
- Device Tree changes (includcing YAML conversion) for
silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577,
maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576"
* tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible
mfd: bd9576: fix typos in comments
mfd: Use platform_get_irq() to get the interrupt
mfd: db8500-prcmu: Remove unused inline function
mfd: arizona-spi: Add Android board ACPI table handling
mfd: arizona-spi: Split Windows ACPI init code into its own function
mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS
mfd: intel-lpss: Provide an SSP type to the driver
dt-bindings: mfd: brcm,cru: Rename pinctrl node
dt-bindings: Add compatibles for undocumented trivial syscons
mfd: atmel-flexcom: Fix compilation warning
dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC
dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema
mfd: exynos-lpass: Drop unneeded syscon.h include
mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs
mfd: ab8500: Drop debugfs module
mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC
mfd: ab8500: Rewrite bindings in YAML
mfd: qcom-spmi-pmic: Add pm8953 compatible
...
Clarify why we need to ping the watchdog before changing the timeout by
quoting the MAX77714 datasheet.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MAX77714 is a MFD chip whose watchdog has the same programming
procedures as the MAX77620 watchdog, but most register offsets and bit
masks are different, as well as some features.
Support the MAX77714 watchdog by adding a variant description table holding
the differences.
All the features implemented by this driver are available on the MAX77714
except for the lack of a WDTOFFC bit. Instead of using a "HAS_*" flag we
handle this by holding in the cnfg_glbl2_cfg_bits struct field the bits
(i.e. the features) to enable in the CNFG_GLBL2 register. These bits differ
among the two models. This implementation allows to avoid any conditional
code, keeping the execution flow unchanged.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmHih/MACgkQ+iyteGJfRsqJBQCeN3KG3aVFcHwFM7EgNIRpqQCp
swMAoK0LtVw4gTrQX8YxJ+Ml/ZVz3guA
=NVYY
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.17-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- New device support:
- Watchdog Timer driver for RZ/G2L
- Realtek Otto watchdog timer
- Apple SoC watchdog driver
- Fintek F81966
- Remove BCM63XX_WDT after support for this SoC was added to
BCM7038_WDT
- Improvements of the BCM7038_WDT and s3c2410_wdt code
- Several other fixes and improvements
* tag 'linux-watchdog-5.17-rc1' of git://www.linux-watchdog.org/linux-watchdog: (38 commits)
watchdog: msc313e: Check if the WDT was running at boot
watchdog: Add Apple SoC watchdog driver
dt-bindings: watchdog: Add SM6350 and SM8250 compatible
watchdog: s3c2410: Fix getting the optional clock
watchdog: s3c2410: Use platform_get_irq() to get the interrupt
dt-bindings: watchdog: atmel: Add missing 'interrupts' property
watchdog: mtk_wdt: use platform_get_irq_optional
watchdog: Add Watchdog Timer driver for RZ/G2L
dt-bindings: watchdog: renesas,wdt: Add support for RZ/G2L
watchdog: da9063: Add hard dependency on I2C
watchdog: Add Realtek Otto watchdog timer
dt-bindings: watchdog: Realtek Otto WDT binding
watchdog: s3c2410: Add Exynos850 support
watchdog: da9063: use atomic safe i2c transfer in reset handler
watchdog: davinci: Use div64_ul instead of do_div
watchdog: Remove BCM63XX_WDT
MIPS: BCM63XX: Provide platform data to watchdog device
watchdog: bcm7038_wdt: Add platform device id for bcm63xx-wdt
watchdog: Allow building BCM7038_WDT for BCM63XX
watchdog: bcm7038_wdt: Support platform data configuration
...
Check if the WDT was running at boot and set the running
flag if it was. This prevents the system from getting
rebooted if the userland daemon doesn't take over soon enough
or there isn't a userland daemon at all.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Reviewed-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211228073427.2443174-1-daniel@0x0f.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add support for the watchdog timer found in Apple SoCs. This driver is
also required to reboot these machines.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211211123633.4392-2-sven@svenpeter.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
"watchdog_src" clock is optional and may not be present for some SoCs
supported by this driver. Nevertheless, in case the clock is provided
but some error happens during its getting, that error should be handled
properly. Use devm_clk_get_optional() API for that. Also report possible
errors using dev_err_probe() to handle properly -EPROBE_DEFER error (if
clock provider is not ready by the time WDT probe function is executed).
Fixes: e249d01b5e ("watchdog: s3c2410: Support separate source clock")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211212170247.30646-1-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211216214747.10454-1-prabhakar.mahadev-lad.rj@bp.renesas.com
[groeck: Fixed context conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The watchdog pre-timeout (bark) interrupt is optional. Use
platform_get_irq_optional() to avoid seeing such following
error message:
>>> mtk-wdt 10007000.watchdog: IRQ index 0 not found
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211208095555.4099551-1-tzungbi@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add Watchdog Timer driver for RZ/G2L SoC.
WDT IP block supports normal watchdog timer function and reset
request function due to CPU parity error.
This driver currently supports normal watchdog timer function
and later will add support for reset request function due to
CPU parity error.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211130195357.18626-3-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Commit 5ea29919c294 ("watchdog: da9063: use atomic safe i2c transfer in
reset handler") implements atomic save i2c transfer which uses i2c
functions directly. Add I2C hard dependency which overrides COMPILE_TEST.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 968011a291 ("watchdog: da9063: use atomic safe i2c transfer in reset handler")
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211129134938.3273289-1-andrej.picej@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Realtek MIPS SoCs (platform name Otto) have a watchdog timer with
pretimeout notifitication support. The WDT can (partially) hard reset,
or soft reset the SoC.
This driver implements all features as described in the devicetree
binding, except the phase2 interrupt, and also functions as a restart
handler. The cpu reset mode is considered to be a "warm" restart, since
this mode does not reset all peripherals. Being an embedded system
though, the "cpu" and "software" modes will still cause the bootloader
to run on restart.
It is not known how a forced system reset can be disabled on the
supported platforms. This means that the phase2 interrupt will only fire
at the same time as reset, so implementing phase2 is of little use.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/6d060bccbdcc709cfa79203485db85aad3c3beb5.1637252610.git.sander@svanheule.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Exynos850 is a bit different from SoCs already supported in WDT driver:
- AUTOMATIC_WDT_RESET_DISABLE register is removed, so its value is
always 0; .disable_auto_reset callback is not set for that reason
- MASK_WDT_RESET_REQUEST register is replaced with
CLUSTERx_NONCPU_IN_EN register; instead of masking (disabling) WDT
reset interrupt it's now enabled with the same value; .mask_reset
callback is reused for that functionality though
- To make WDT functional, WDT counter needs to be enabled in
CLUSTERx_NONCPU_OUT register; it's done using .enable_counter
callback
Also Exynos850 has two CPU clusters, each has its own dedicated WDT
instance. Different PMU registers and bits are used for each cluster. So
driver data is now modified in probe, adding needed info depending on
cluster index passed from device tree.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211121165647.26706-13-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch is based on commit 057b52b4b3 ("watchdog: da9062: make restart
handler atomic safe"), which uses the atomic transfer capability of the
i2c framework.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211124080654.2601135-1-andrej.picej@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
do_div() does a 64-by-32 division. Here the divisor is an unsigned long
which on some platforms is 64 bit wide. So use div64_ul instead of do_div
to avoid a possible truncation.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211125014924.46297-1-deng.changcheng@zte.com.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Now that we can utilize the BCM7038_WDT driver, remove that one which
was not converted to the watchdog APIs. There are a couple of notable
differences with how the bcm7038_wdt driver proceeds:
- bcm63xx_wdt would register with the ad-hoc BCM63xx hardware timer API,
but this would only be used in order to catch the interrupt *before* a
SoC reset and make the kernel "die"
- bcm6xx_wdt would register a software timer and kick it every second in
order to pet the watchdog, thus offering a two step watchdog process.
This is not something that is brought over to the bcm7038_wdt as it is
deemed unnecessary. If user-space cannot pet the watchdog, but a
kernel timer can, the system is still in a bad shape anyway.
bcm7038_wdt is simpler in its behavior and behaves as a standard
watchdog driver and is not making use of any specific platform APIs,
therefore making it more maintainable and extensible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211112224636.395101-8-f.fainelli@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In order to phase out bcm63xx_wdt and use bcm7038_wdt instead, introduce
a platform_device_id table that allows both names to be matched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211112224636.395101-6-f.fainelli@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
CONFIG_BCM63XX denotes the legacy MIPS-based DSL SoCs which utilize the
same piece of hardware as a watchdog, make it possible to select that
driver for those platforms.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211112224636.395101-5-f.fainelli@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The BCM7038 watchdog driver needs to be able to obtain a specific clock
name on BCM63xx platforms which is the "periph" clock ticking at 50MHz.
make it possible to specify the clock name to obtain via platform data.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211112224636.395101-4-f.fainelli@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Remove watchdog_stop_on_reboot()
The Meson platform still has some hardware drivers problems for some
configurations which can freeze devices on shutdown/reboot.
Remove watchdog_stop_on_reboot() to catch this situation and ensure that
the reboot happens anyway. Users who still want to stop the watchdog on
reboot can still do so using the watchdog.stop_on_reboot=1 module
parameter.
https://lore.kernel.org/linux-watchdog/20210729072308.1908904-1-art@khadas.com/T/#t
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211110022518.1676834-1-art@khadas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Some entries indent their help text with 1 tab + 1 space or 1 tab only
instead of 1 tab + 2 spaces. Add the missing spaces.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211111225852.3128201-7-luca@lucaceresoli.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
'err' label in probe function is not really need, it just returns.
Remove it and replace all 'goto' statements with actual returns in
place.
No functional change here, just a cleanup patch.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-12-semen.protsenko@linaro.org
[groeck: Fixed context conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Right now all devices supported in the driver have the single clock: it
acts simultaneously as a bus clock (providing register interface
clocking) and source clock (driving watchdog counter). Some newer Exynos
chips, like Exynos850, have two separate clocks for that. In that case
two clocks will be passed to the driver from the resource provider, e.g.
Device Tree. Provide necessary infrastructure to support that case:
- use source clock's rate for all timer related calculations
- use bus clock to gate/ungate the register interface
All devices that use the single clock are kept intact: if only one clock
is passed from Device Tree, it will be used for both purposes as before.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-11-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Now that PMU enablement code was extended for new Exynos SoCs, it
doesn't look very cohesive and consistent anymore. Do a bit of renaming,
grouping and style changes, to make it look good again. While at it, add
quirks documentation as well.
No functional change, just a refactoring commit.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211123232613.22438-1-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
On new Exynos chips (e.g. Exynos850) new CLUSTERx_NONCPU_OUT register is
introduced, where CNT_EN_WDT bit must be enabled to make watchdog
counter running. Add corresponding quirk and proper infrastructure to
handle that register if the quirk is set.
This commit doesn't bring any functional change to existing devices, but
merely provides an infrastructure for upcoming chips support.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-9-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
On new Exynos chips (like Exynos850) the MASK_WDT_RESET_REQUEST register
is replaced with CLUSTERx_NONCPU_INT_EN, and its mask bit value meaning
was reversed: for new register the bit value "1" means "Interrupt
enabled", while for MASK_WDT_RESET_REQUEST register "1" means "Mask the
interrupt" (i.e. "Interrupt disabled").
Introduce "mask_reset_inv" boolean field in driver data structure; when
that field is "true", mask register handling function will invert the
value before setting it to the register.
This commit doesn't bring any functional change to existing devices, but
merely provides an infrastructure for upcoming chips support.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-8-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The s3c2410wdt_mask_and_disable_reset() function content is bound to be
changed further. Prepare it for upcoming changes by splitting into
separate "mask reset" and "disable reset" functions. But keep
s3c2410wdt_mask_and_disable_reset() function present as a facade.
This commit doesn't bring any functional change to existing devices, but
merely provides an infrastructure for upcoming chips support.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-7-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
On new Exynos chips (e.g. Exynos850 and Exynos9) the
AUTOMATIC_WDT_RESET_DISABLE register was removed, and its value can be
thought of as "always 0x0". Add correspondig quirk bit, so that the
driver can omit accessing it if it's not present.
This commit doesn't bring any functional change to existing devices, but
merely provides an infrastructure for upcoming chips support.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-6-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When "tmr_atboot" module param is set, the watchdog is started in
driver's probe. In that case, also set WDOG_HW_RUNNING bit to let
watchdog core driver know it's running. This way watchdog core can kick
the watchdog for us (if CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED option is
enabled), until user space takes control.
WDOG_HW_RUNNING bit must be set before registering the watchdog. So the
"tmr_atboot" handling code is moved before watchdog registration, to
avoid performing the same check twice. This is also logical because
WDOG_HW_RUNNING bit makes WDT core expect actually running watchdog.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-5-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Driver can't work properly if there no valid timeout was found in
s3c2410wdt_set_heartbeat(). Ideally, that function should be reworked in
a way that it's always able to find some valid timeout. As a temporary
solution let's for now just fail the driver probe in case the valid
timeout can't be found in s3c2410wdt_set_heartbeat() function.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211107202943.8859-4-semen.protsenko@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This adds watchdog support the Fintek F81966 Super I/O chip.
Testing was done on the Aaeon SSE-OPTI
Signed-off-by: AaeonIot <sophiehu@aaeon.com.tw>
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211117024052.2427539-1-acelan.kao@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Enable CONFIG_MEDIATEK_WATCHDOG when ARCH_MEDIATEK is enabled.
On some platforms (e.g. mt8183-pumpkin), watchdog is enabled by
bootloader, so kernel driver needs to be enabled to avoid watchdog
firing and causing reboot part way through kernel boot.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211103230354.915658-1-khilman@baylibre.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This driver adds initial support for several devices from Siemens. It is
based on a platform driver introduced in an earlier commit.
One of the supported machines does access a GPIO pin to enable the
watchdog. Here we poke GPIO memory because pinctrl does not come up.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211213120502.20661-4-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmGKax0ACgkQ+iyteGJfRsomvgCgpAmE/d5d9mSpq0zGaLa9ocxt
bfQAniIp5n+wklRuiqYRAyCBdNqbKhAI
=DlM4
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.16-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- f71808e_wdt: convert to watchdog framework
- db8500_wdt: Rename driver (was ux500_wdt.c)
- sunxi: Add compatibles for R329 and D1
- mtk: add disable_wdt_extrst support
- several other small fixes and improvements
* tag 'linux-watchdog-5.16-rc1' of git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: db8500_wdt: Rename symbols
watchdog: db8500_wdt: Rename driver
watchdog: ux500_wdt: Drop platform data
watchdog: bcm63xx_wdt: fix fallthrough warning
watchdog: iTCO_wdt: No need to stop the timer in probe
watchdog: s3c2410: describe driver in KConfig
watchdog: sp5100_tco: Add support for get_timeleft
watchdog: mtk: add disable_wdt_extrst support
dt-bindings: watchdog: mtk-wdt: add disable_wdt_extrst support
watchdog: rza_wdt: Use semicolons instead of commas
watchdog: mlx-wdt: Use regmap_write_bits()
watchdog: rti-wdt: Make use of the helper function devm_platform_ioremap_resource()
watchdog: iTCO_wdt: Make use of the helper function devm_platform_ioremap_resource()
watchdog: ar7_wdt: Make use of the helper function devm_platform_ioremap_resource_byname()
watchdog: sunxi_wdt: Add support for D1
dt-bindings: watchdog: sunxi: Add compatibles for D1
ar7: fix kernel builds for compiler test
dt-bindings: watchdog: sunxi: Add compatibles for R329
watchdog: meson_gxbb_wdt: add timeout parameter
watchdog: meson_gxbb_wdt: add nowayout parameter
...
This is a rather large update for the ARM devicetree files, after a few
quieter releases, with 775 total commits and 47 branches pulled into
this one. There are 5 new SoC types plus some minor variations, and
a total of 60 new machines, so I'm limiting the summary to the main
noteworthy items:
- Apple M1 gain support for PCI and pinctrl, getting a bit
closer to a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as
well as SM7225, 11 new smartphones, and three additional
Chromebooks, and improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version
of their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a
number of improvements for the recently added SAMA7 family.
The LAN966 SoC that was added in the platform code does not
have dts files yet. Two board files are added for the older
at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600
as BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new
development boards using RK3328/RK3399/RK3566, and one
Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the
new MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based
ebook readers, and three additional development boards, which
is notably less than their usual additions, but they also gain
improvements to their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with
a reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many
updates for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi
boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for
more hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub
home automation controllers, along with changes to other
machines
- Rob Herring continues his work on fixing dtc warnings all over
the tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc
-----BEGIN PGP SIGNATURE-----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=jp4P
-----END PGP SIGNATURE-----
Merge tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
For conistency and clarity, rename all symbols and strings from
ux500 to db8500 in the driver.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210922230947.1864357-3-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This driver is named after the ambition to support more SoCs than
the DB8500. Those were never produced, so cut down the scope and
rename the driver accordingly. Since the Kconfig for the watchdog
defaults to y this will still be built by default.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210922230947.1864357-2-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Drop the platform data passing from the PRCMU driver. This platform
data was part of the ambition to support more SoCs, which in turn
were never mass produced.
Only a name remains of the MFD cell so switch to MFD_CELL_NAME().
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210922230947.1864357-1-linus.walleij@linaro.org
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This fixes:
drivers/watchdog/bcm63xx_wdt.c: In function 'bcm63xx_wdt_ioctl':
drivers/watchdog/bcm63xx_wdt.c:208:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211027123135.27458-1-zajec5@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The watchdog core can handle pinging of the watchdog before userspace
opens the device. For this reason instead of stopping the timer, just
mark it as running and let the watchdog core take care of it.
Cc: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210921102900.61586-1-mika.westerberg@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210924132930.111443-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Tested on a Gigabyte X570 I AORUS PRO WIFI.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210928065735.548966-1-linux@weissschuh.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In some cases, we may need watchdog just to trigger an
internal soc reset without sending any output signal.
Provide a disable_wdt_extrst parameter for configuration.
We can disable or enable it just by configuring dts.
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210914123454.32603-3-Fengquan.Chen@mediatek.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This code works, but it is cleaner to use semicolons at the end of
statements instead of commas.
Extracted from a big anonymous patch by Julia Lawall
<julia.lawall@inria.fr>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/fa4451efd21e287f8fdf2f7f8495b070544209c0.1631699262.git.geert+renesas@glider.be
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the regmap_write_bits() macro instead of regmap_update_bits_base().
No functional change.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907092732.31815-1-p.zabel@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907074237.2808-1-caihuoqing@baidu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907074230.2757-1-caihuoqing@baidu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907074223.2706-1-caihuoqing@baidu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
D1 adds a key field to the "CFG" and "MODE" registers, that must be set
to change the other bits. Add logic to set the key when updating those
registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210902225750.29313-4-samuel@sholland.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
TI AR7 Watchdog Timer is only build for 32bit.
Avoid error like:
In file included from drivers/watchdog/ar7_wdt.c:29:
./arch/mips/include/asm/mach-ar7/ar7.h: In function ‘ar7_is_titan’:
./arch/mips/include/asm/mach-ar7/ar7.h:111:24: error: implicit declaration of function ‘KSEG1ADDR’; did you mean ‘CKSEG1ADDR’? [-Werror=implicit-function-declaration]
111 | return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x24)) & 0xffff) ==
| ^~~~~~~~~
| CKSEG1ADDR
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907024904.4127611-1-liu.yun@linux.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Proper machine resets via da9062/da9063 PMICs are very tricky as they
require special i2c atomic transfers when interrupts are not available
anymore. This is also a reason why both PMIC's restart handlers do not
use regmap but instead opt for i2c_smbus_write_byte_data() which does
i2c transfer in atomic manner. Under the hood, this function tries to
obtain i2c bus lock with call to i2c_adapter_trylock_bus() which will
return -EAGAIN (-11) if lock is not available.
Since commit 982bb70517 ("watchdog: reset last_hw_keepalive time at
start") occasional restart handler failures with "Failed to shutdown
(err = -11)" error messages were observed, indicating that some
process is holding the i2c bus lock. Investigation into the matter
uncovered that sometimes during reboot sequence watchdog ping is issued
late into poweroff/reboot phase which did not happen before mentioned
commit (usually the watchdog ping happened immediately as commit message
suggests). As of now, when watchdog ping usually happens late into
poweroff/reboot stage when interrupts are not available anymore, i2c bus
lock cannot be released anymore and pending restart handler in turn
fails.
Thus, to prevent such late watchdog pings from happening ahead of
pending machine restart and consequently locking up the i2c bus, check
for system_state in watchdog ping handler and consequently do not send
pings anymore in case system_state > SYSTEM_RUNNING.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20210708082128.2832904-1-primoz.fiser@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
While the driver will only match against a single device, convention is
to dynamically allocate the driver data.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1baffdc410d6476cccffe9712cec56350335812a.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Driver so far wasn't ported to the driver model and registered
the watchdog device out of the init after probing the I/O ports
for a watchdog with correct vendor and device revision.
Keep the device detection part at init time, but move watchdog
registration to a platform driver probe function.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/9e1088839662e5c357286cab0b9de0bb0602e4fd.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Migrating the driver lets us drop the watchdog misc device boilerplate
and reduces size by 285 lines. It also brings us support for new
functionality like CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED.
This incurs a slight backwards-compatibility break, because the new
kernel watchdog API doesn't support unloading modules for drivers
whose watchdog hardware is reported to be running.
This means following scenario will be no longer supported:
- BIOS has enabled watchdog
- Module is loaded and unloaded without opening watchdog
- module_exit is expected to succeed and disable watchdog HW
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/35d9dbf57b58c5f003cef31dc256ec2fec044524.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Code for the common parts of the driver either uses watchdog_ as
prefix for the watchdog API or f71808e_ for everything else.
The driver now supports 9 more variants besides the f71808e,
so let's rename the common parts to start with fintek_wdt_ instead.
This makes code browsing easier, because it's readily apparent
that functions are not variant-specific. Some watchdog_-prefixed
functions remain, but these will be dropped altogether with the move
to the kernel watchdog API in a later commit.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/31805c6aeb8d161f852ddad7c32b91319f924988.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The fintek_wdt_names is meant for read-only use and is currently not
modified. Mark it const to catch future writes.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/9720c5a1efcef861da68b693453bb3eb3c21af37.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
max_timeout never served any purpose over WATCHDOG_MAX_TIMEOUT, which it
was initialized with. Drop it.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/d1f8cda90283855633537adee0af2c6b00a9ec25.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The fintek watchdog timer can configure timeouts of second granularity
only up to 255 seconds. Beyond that, the timeout needs to be configured
with minute granularity. WDIOC_GETTIMEOUT should report the actual
timeout configured, not just echo back the timeout configured by the
user. Do so.
Fixes: 96cb4eb019 ("watchdog: f71808e_wdt: new watchdog driver for Fintek F71808E and F71882FG")
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/5e17960fe8cc0e3cb2ba53de4730b75d9a0f33d5.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In the function stm32_iwdg_probe(), devm_platform_ioremap_resource
has already contained error message, so drop the redundant one.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210814142741.7396-1-tangbin@cmss.chinamobile.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
TI's implementation does not service the watchdog even if the kernel
command line parameter omap_wdt.early_enable is set to 1. This patch
fixes the issue.
Signed-off-by: Walter Stoll <walter.stoll@duagon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/88a8fe5229cd68fa0f1fd22f5d66666c1b7057a0.camel@duagon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210917092024.19323-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
SBSA says of the generic watchdog:
All registers are 32 bits in size and should be accessed using 32-bit
reads and writes. If an access size other than 32 bits is used then
the results are IMPLEMENTATION DEFINED.
and for qemu, the implementation will only allow 32-bit accesses
resulting in a synchronous external abort when configuring the watchdog.
Use lo_hi_* accessors rather than a readq/writeq.
Fixes: abd3ac7902 ("watchdog: sbsa: Support architecture version 1")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/20210903112101.493552-1-quic_jiles@quicinc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This reverts commit cb011044e3 ("watchdog: iTCO_wdt: Account for
rebooting on second timeout") and commit aec42642d9 ("watchdog: iTCO_wdt:
Fix detection of SMI-off case") since those patches cause a regression
on certain boards (https://bugzilla.kernel.org/show_bug.cgi?id=213809).
While this revert may result in some boards to only reset after twice
the configured timeout value, that is still better than a watchdog reset
after half the configured value.
Fixes: cb011044e3 ("watchdog: iTCO_wdt: Account for rebooting on second timeout")
Fixes: aec42642d9 ("watchdog: iTCO_wdt: Fix detection of SMI-off case")
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Mantas Mikulėnas <grawity@gmail.com>
Reported-by: Javier S. Pedro <debbugs@javispedro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211008003302.1461733-1-linux@roeck-us.net
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The DT binding includes for reset controllers are located in
include/dt-bindings/reset/. Move the Mediatek reset constants in there.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20210930103105.v4.1.I514d9aafff3a062f751b37d3fea7402f67595b86@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Compiling sb_watchdog needs to clearly define SIBYTE_HDR_FEATURES.
In arch/mips/sibyte/Platform like:
cflags-$(CONFIG_SIBYTE_BCM112X) += \
-I$(srctree)/arch/mips/include/asm/mach-sibyte \
-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
Otherwise, SIBYTE_HDR_FEATURES is SIBYTE_HDR_FMASK_ALL.
SIBYTE_HDR_FMASK_ALL is mean:
#define SIBYTE_HDR_FMASK_ALL SIBYTE_HDR_FMASK_1250_ALL | SIBYTE_HDR_FMASK_112x_ALL \
| SIBYTE_HDR_FMASK_1480_ALL)
So, If not limited to CPU_SB1, we will get such an error:
arch/mips/include/asm/sibyte/bcm1480_scd.h:261: error: "M_SPC_CFG_CLEAR" redefined [-Werror]
arch/mips/include/asm/sibyte/bcm1480_scd.h:262: error: "M_SPC_CFG_ENABLE" redefined [-Werror]
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This rewrites the IXP4xx watchdog driver as follows:
- Spawn the watchdog driver as a platform device from the timer
driver. It's one device in the hardware, and the fact that
Linux splits the handling into two different devices is
a Linux pecularity, and thus it becomes a Linux pecularity
to spawn a separate watchdog driver.
- Spawn the watchdog driver from the timer driver at probe().
This is well after the timer driver as actually registered and
started and we know the register base is available.
- Instead of looping back callbacks to the timer drivers for all
watchdog calls, pass the register base to the watchdog driver
and manage the registers there. The two drivers aren't even
interested in the same register so the spinlock is totally
surplus, delete it.
- Replace pretty much all of the content in the watchdog driver
with a simple, modern watchdog driver utilizing the watchdog
core instead of registering its own misc device and ioctl()
handling.
- Drop module parameters as the same already exist in the
watchdog core.
What remains is a slim elegant (IMO) watchdog driver using the
watchdog core, spawning from device tree or boardfile alike.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210726121214.2572836-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We must not pet a running watchdog when handle_boot_enabled is off
because this will kick off automatic triggering before userland is
running, defeating the purpose of the handle_boot_enabled control.
Furthermore, don't ping in case watchdog_set_last_hw_keepalive was
called incorrectly when the hardware watchdog is actually not running.
Fixed: cef9572e9a ("watchdog: add support for adjusting last known HW keepalive time")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/93d56386-6e37-060b-55ce-84de8cde535f@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This adds device tree probing to the MAX63xx driver so it can be
instantiated from the device tree. We use the generic fwnode-based
method to get to the match data and clean up by constifying the
functions as the match is indeed a const.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210714153314.1004147-2-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The struct tqmx86_wdt_ops is only assigned to the ops pointer in the
watchdog_device struct, which is a pointer to const struct watchdog_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210727223042.48150-3-rikard.falkeborn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The struct mpc8xxx_wdt_ops is only assigned to the ops pointer in the
watchdog_device struct, which is a pointer to const struct watchdog_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210727223042.48150-4-rikard.falkeborn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The struct sl28cpld_wdt_ops is only assigned to the ops pointer in the
watchdog_device struct, which is a pointer to const struct watchdog_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210727223042.48150-2-rikard.falkeborn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Obviously, the test needs to run against the register content, not its
address.
Fixes: cb011044e3 ("watchdog: iTCO_wdt: Account for rebooting on second timeout")
Cc: stable@vger.kernel.org
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Link: https://lore.kernel.org/r/d84f8e06-f646-8b43-d063-fb11f4827044@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Until now all Raspberry Pi boards used the power off function of the SoC.
But the Raspberry Pi 400 uses gpio-poweroff for the whole board which
possibly cannot register the poweroff handler because the it's
already registered by this watchdog driver. So consider the
system-power-controller property for registering, which is already
defined in soc/bcm/brcm,bcm2835-pm.txt .
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1622981777-5023-3-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Suspend routine disables wdog clk. Nevertheless, the watchdog subsystem
is not aware of that and can still try to ping wdog through
watchdog_ping_work. In order to prevent such condition and therefore
prevent from system hang (caused by the wdog register access issued
while the wdog clock is disabled) notify watchdog core that the ping
worker should be canceled during watchdog core suspend and restored
during resume.
Signed-off-by: Michal Koziel <michal.koziel@emlogic.no>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210618195033.3209598-3-grzegorz.jaszczyk@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The watchdog drivers often disable wdog clock during suspend and then
enable it again during resume. Nevertheless the ping worker is still
running and can issue low-level ping while the wdog clock is disabled
causing the system hang. To prevent such condition register pm notifier
in the watchdog core which will call watchdog_dev_suspend/resume and
actually cancel ping worker during suspend and restore it back, if
needed, during resume.
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210618195033.3209598-2-grzegorz.jaszczyk@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
watchdog_hrtimer_pretimeout_stop needs the watchdog device to have a
valid pointer to the watchdog core data to stop the pretimeout hrtimer.
Therefore it needs to be called before the pointers are cleared in
watchdog_cdev_unregister.
Fixes: 7b7d2fdc8c ("watchdog: Add hrtimer-based pretimeout feature")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1624429583-5720-1-git-send-email-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Some watchdog devices might conditionally support pretimeouts (e.g. if
an interrupt is exposed for the device) but some watchdog drivers might
still define the set_pretimeout operation (e.g. the mtk_wdt driver) and
indicate support at runtime through the WDIOF_PRETIMEOUT flag. If the
kernel is compiled with CONFIG_WATCHDOG_HRTIMER_PRETIMEOUT enabled,
watchdog_set_pretimeout would run the driver specific set_pretimeout
even if WDIOF_PRETIMEOUT is not set which might have unintended
consequences.
So this change checks that the device flags and only runs the driver
operation if pretimeouts are supported.
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1624751265-24785-1-git-send-email-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/994d2e374262c3f59f4465c03ef23d3116120778.1621937490.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which always
return IRQ_HANDLED which turns the spurious interrupt detection into a
pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level flow
handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=FIKh
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which
always return IRQ_HANDLED which turns the spurious interrupt
detection into a pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level
flow handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements"
* tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
irqchip: gic-pm: Remove redundant error log of clock bulk
irqchip/sun4i: Remove unnecessary oom message
irqchip/irq-imx-gpcv2: Remove unnecessary oom message
irqchip/imgpdc: Remove unnecessary oom message
irqchip/gic-v3-its: Remove unnecessary oom message
irqchip/gic-v2m: Remove unnecessary oom message
irqchip/exynos-combiner: Remove unnecessary oom message
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
...
Over time the functions were renamed,
but this was not always reflected in kdoc, fix that.
Signed-off-by: Tamar Mashiah <tamar.mashiah@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20210621193756.134027-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() instead of pr_err(), so device name is also shown in the log.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210616181708.19530-2-info@metux.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
It adds a driver for the IP block handling the watchdog timer found for
Mstar MSC313e SoCs and newer.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Co-developed-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210611200801.52139-3-romain.perier@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This was already attempted to fix via 1fccb73011: If the BIOS did not
enable TCO SMIs, the timer definitely needs to trigger twice in order to
cause a reboot. If TCO SMIs are on, as well as SMIs in general, we can
continue to assume that the BIOS will perform a reboot on the first
timeout.
QEMU with its ICH9 and related BIOS falls into the former category,
currently taking twice the configured timeout in order to reboot the
machine. For iTCO version that fall under turn_SMI_watchdog_clear_off,
this is also true and was currently only addressed for v1, irrespective
of the turn_SMI_watchdog_clear_off value.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/0b8bb307-d08b-41b5-696c-305cdac6789c@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add support for compatible sama7g5-wdt.
The sama7g5 wdt is the same hardware block as on sam9x60.
Adapt the driver to use the sam9x60/sama7g5 variant if either
of the two compatibles are selected (sam9x60-wdt/sama7g5-wdt).
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210527100120.266796-2-eugen.hristev@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Remove the ZIIRAVE_{BL,FW}_VERION_FMT defines since they're only used in
very few places. While at it, add newlines to sysfs outputs.
Suggested-By: Joe Perches <joe@perches.com>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210520072918.76482-1-juergh@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If the WDIOF_PRETIMEOUT flag is not set when registering the device the
driver will not show the sysfs entries or register the default governor.
By moving the registering after the decision whether pretimeout is
supported this gets fixed.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20210519080311.142928-1-eichest@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The assign for 'ret' is redundant and can be removed,
because it will be assigned before use.
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210203122404.752-1-angkery@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This adds the option to use a hrtimer to generate a watchdog pretimeout
event for hardware watchdogs that do not natively support watchdog
pretimeouts.
With this enabled, all watchdogs will appear to have pretimeout support
in userspace. If no pretimeout value is set, there will be no change in
the watchdog's behavior. If a pretimeout value is set for a specific
watchdog that does not have built-in pretimeout support, a timer will be
started that should fire at the specified time before the watchdog
timeout would occur. When the watchdog is successfully pinged, the timer
will be restarted. If the timer is allowed to fire it will generate a
pretimeout event. However because a software timer is used, it may not
be able to fire in every circumstance.
If the watchdog does support a pretimeout natively, that functionality
will be used instead of the hrtimer.
The general design of this feaure was inspired by the software watchdog,
specifically its own pretimeout implementation. However the software
watchdog and this feature are completely independent. They can be used
together; with or without CONFIG_SOFT_WATCHDOG_PRETIMEOUT enabled.
The main advantage of using the hrtimer pretimeout with a hardware
watchdog, compared to running the software watchdog with a hardware
watchdog, is that if the hardware watchdog driver is unable to ping the
watchdog (e.g. due to a bus or communication error), then the hrtimer
pretimeout would still fire whereas the software watchdog would not.
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1612383090-27110-1-git-send-email-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
During suspend/resume usecases and tests, it is common to see issues
such as lockups either in suspend path or resume path because of the
bugs in the corresponding device driver pm handling code. In such cases,
it is important that watchdog is active to make sure that we either
receive a watchdog pretimeout notification or a bite causing reset
instead of a hang causing us to hard reset the machine.
There are good reasons as to why we need this because:
* We can have a watchdog pretimeout governor set to panic in which
case we can have a backtrace which would help identify the issue
with the particular driver and cause a normal reboot.
* Even in case where there is no pretimeout support, a watchdog
bite is still useful because some firmware has debug support to dump
CPU core context on watchdog bite for post-mortem analysis.
* One more usecase which comes to mind is of warm reboot. In case we
hard reset the target, a cold reboot could be induced resulting in
lose of ddr contents thereby losing all the debug info.
Currently, the watchdog pm callback just invokes the usual suspend
and resume callback which do not have any special ordering in the
sense that a watchdog can be suspended before the buggy device driver
suspend callback and watchdog resume can happen after the buggy device
driver resume callback. This would mean that the watchdog will not be
active when the buggy driver cause the lockups thereby hanging the
system. So to make sure this doesn't happen, move the watchdog pm to
use late/early system pm callbacks which will ensure that the watchdog
is suspended late and resumed early so that it can catch such issues.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210310202004.1436-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In case of error, the function device_node_to_regmap() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: 6d532143c9 ("watchdog: jz4740: Use regmap provided by TCU driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210304045909.945799-1-weiyongjun1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the bark interrupt as the pretimeout notifier if available.
When the watchdog timer expires in dual mode, an interrupt will be
triggered first, then the timing restarts. The reset signal will be
initiated when the timer expires again.
The pretimeout notification shall occur at timeout-sec/2.
V2:
- panic() by default if WATCHDOG_PRETIMEOUT_GOV is not enabled.
V3:
- Modify the pretimeout behavior, manually reset after the pretimeout
- is processed and wait until timeout.
V4:
- Remove pretimeout related processing.
- Add dual mode control separately.
V5:
- Fix some formatting and printing problems.
V6:
- Realize pretimeout processing through dualmode.
V7:
- Add set_pretimeout().
V8/V9:
- Fix some formatting problems.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1619315527-8171-2-git-send-email-wangqing@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The command 'find drivers/watchdog | xargs ./scripts/kernel-doc -none'
reports a number of kernel-doc warnings in the watchdog subsystem.
Address the kernel-doc warnings that were purely syntactic issues with
kernel-doc comments.
The remaining kernel-doc warnings are of type "Excess function parameter"
and "Function parameter or member not described". These warnings would
need to be addressed in a second pass with a bit more insight into the
APIs and purpose of the functions in the watchdog subsystem.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210322065337.617-1-lukas.bulwahn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
"%p" is not printing the pointer value.
In driver, printing pointer value is not useful so avoiding print.
iSigned-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-6-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
clk is an optional property, if clock not defined,
calling clk_prepare_enable() and devm_add_action_or_reset()
are not useful.
so calling these two apis only when clock is present.
Addresses-Coverity:"FORWARD_NULL"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-5-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch removes pr_info in stop function and adds dev_dbg()
in start/stop function to display device specific debug info.
Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-4-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Based on checkpatch every spinlock should be documented.
The patch is fixing this issue:
./scripts/checkpatch.pl --strict -f drivers/watchdog/of_xilinx_wdt.c
CHECK: spinlock_t definition without comment
+ spinlock_t spinlock;
Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-2-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the device_get_match_data() helper instead of open coding.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1617243921-56774-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fix hardware timeout calculation in aspeed_wdt_set_timeout function to
ensure the reload value does not exceed the hardware limit.
Fixes: efa859f7d7 ("watchdog: Add Aspeed watchdog driver")
Reported-by: Amithash Prasad <amithash@fb.com>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210417034249.5978-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Change a non-working ftp: URL to https:.
Wrap long lines earlier.
Spell "IP" with capital letters.
Change "it`s" to "it's". The backtick (grave accent) is not an apostrophe.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210419000704.17745-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Convert sprintf() in sysfs "show" functions to sysfs_emit() and
sysfs_emit_at() in order to check for buffer overruns in sysfs outputs.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210511061812.480172-1-juergh@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This driver's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/1620802676-19701-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620716691-108460-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The valid range for the 'timeout' value is useful information so expose
the min and max timeout values via sysfs.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210511062953.485252-1-juergh@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Kernel doc validation script is not happy
CHECK .../sp805_wdt.c
.../sp805_wdt.c:73: warning: Function parameter or member 'rate' not described in 'sp805_wdt'
Fix this by describing rate parameter.
While at it, mark clk one optional.
Fixes: dc0e4a3bb7 ("watchdog: sp805: Add clock-frequency property")
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210517174912.26419-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Replace open coded variants of devm_clk_get_optional().
While at it, drop unneeded OF and ACPI dependency as the APIs in use
are provider agnostic.
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Link: https://lore.kernel.org/r/20210517174456.22050-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
New hardware with new PCI ID info.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620878612-24736-2-git-send-email-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
