In some case, the btmrvl_sdio firmware would fail to active within the
polling time. Increase the polling interval to 100 msec to fix the
issue.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Lenovo ThinkPad Tablet 8 with BCM43241 rev B5 chipset uses the BCM2E55
ACPI ID for Bluetooth. Add it to the list of supported devices.
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The AG6xx devices behave similar to Wilkens Peak and Stone Peak and with
that it is needed to check for Intel default address. In addition it is
possible to enable vendor events and diag support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This driver implements support for iBT2.1 Bluetooth controller embedded
in the AG620 communication combo. The controller needs to be configured
with bddata and can be patched with a binary patch file (pbn).
These operations are performed in manufacturing mode.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the call to request_firmware() fails in btbcm_setup_patchram(),
the BCM chip will be operating with its default firmware.
In this case, btbcm_setup_patchram() should not return immediately
but instead should skip to btbcm_check_bdaddr() and quirk setup.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recent macbooks (early 2015) with BCM43241 use this ACPI ID. Add it to the
list of supported devices.
Reported-by: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This ACPI ID is used at least by HP for their Omni 10 5600eg tablet.
Signed-off-by: J.J. Meijer <jjmeijer88@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A return value of the intel_wait_booting() function compared with
a constant ETIMEDOUT instead of -ETIMEDOUT.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed a coding style issue. Added a blank link after declaration.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Usually when driver sends data to firmware it receives TX_DONE
(DN_LD_HOST_INT_STATUS) interrupt from firmware right away.
It's also observed that some times the fireware could delay
sending DN_LD_HOST_INT_STATUS interrupt. If driver sends data to
firmware during suspend processing and the TX_DONE interrupt is
delayed, it may come back at wrong time when SDIO host driver is
in the middle of suspending.
Block any data from stack while suspending. Also skip sending
data that are already in driver tx_queue.
Don't purge the skb queue on suspend to avoid intermittent music
after system resumes from S3.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For gpio=0xff (wake up host through SDIO interface) case,
gap=0xff means no delay (same as gap=0) for incoming data packet
to be sent to host after host sleep is activated.
Change it to the maximum delay to reduce the chance that RX
interrupt could be delivered while host controller suspends.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These are used at least by Acer with BCM43241.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The IDs should all be for Broadcom BCM43241 module, and
hci_bcm is now the proper driver for them. This removes one
of two different ways of handling PM with the module.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
devm_kzalloc prints its own OOM message upon failure.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
devm_kzalloc prints its own OOM message upon failure.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add BCM2E65 device in acpi_device_id table used on Asus T100TAF.
Signed-off-by: Luka Karinja <luka.karinja@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initializing Configuration field in H5 Config message to 0x01 gives
wrong impression that the value is used and needed. Later on the whole
field is rewritten with h5_cfg_field().
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel Version Read command is used to retrieve information
about hardware and firmware version/revision of Intel Bluetooth
controllers. This is an Intel generic command used in USB and
UART drivers.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Older Intel controllers need to enter manufacturing mode to perform
some vendor specific operations (patching, configuration...).
Add enter/exit manufaturing methods and refactor existing
manufacturing code.
Exit can be configured to perform a reset. Reset can be performed
either with patches activated or deactivated.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the standard HCI_CMD_TIMEOUT(1s) for HCI command instead of
HCI_INIT_TIMEOUT(10s) which is not justified in these cases.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The N_HCI ldisc does not define a flush_buffer() ldisc method, so
the check when opening the ldisc is always false.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only Sliding Window Size is used at the moment for H5 Bluetooth
Configuration messages.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using hexadecimal notation for mask makes code easier to read
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes it easier to read and makes code consistent.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull networking fixes from David Miller:
1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.
2) Several spots need to get to the original listner for SYN-ACK
packets, most spots got this ok but some were not. Whilst covering
the remaining cases, create a helper to do this. From Eric Dumazet.
3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
from Rasmus Villemoes.
4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.
5) Use after free in mvneta driver, from Justin Maggard.
6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.
7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd
Bergmann.
8) Fix multicast getsockopt deadlock, from WANG Cong.
9) Fix deadlock in btusb, from Kuba Pawlak.
10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
counter state. From Sabrina Dubroca.
11) Fix packet_bind() race, which can cause lost notifications, from
Francesco Ruggeri.
12) Fix MAC restoration in qlcnic driver during bonding mode changes,
from Jarod Wilson.
13) Revert bridging forward delay change which broke libvirt and other
userspace things, from Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
Revert "bridge: Allow forward delay to be cfgd when STP enabled"
bpf_trace: Make dependent on PERF_EVENTS
qed: select ZLIB_INFLATE
net: fix a race in dst_release()
net: mvneta: Fix memory use after free.
net: Documentation: Fix default value tcp_limit_output_bytes
macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
mvneta: add FIXED_PHY dependency
net: caif: check return value of alloc_netdev
net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
drivers: net: xgene: fix RGMII 10/100Mb mode
netfilter: nft_meta: use skb_to_full_sk() helper
net_sched: em_meta: use skb_to_full_sk() helper
sched: cls_flow: use skb_to_full_sk() helper
netfilter: xt_owner: use skb_to_full_sk() helper
smack: use skb_to_full_sk() helper
net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
bpf: doc: correct arch list for supported eBPF JIT
dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
bonding: fix panic on non-ARPHRD_ETHER enslave failure
...
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_compatible_node(n, ...) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bt_skb_alloc() returns NULL on error, it never returns an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel Bluetooth controllers can emit extra vendor specific events in
error conditions or for debugging purposes. To make the life easier for
engineers, enable them by default. When the vendor_diag options has been
enabled, then additional debug events are also enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Intel bootloader devices, set the manufacturer information so that
it becomes possible to decode the boot process.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Provide an early indication about the manufacturer information so that
it can be forwarded into monitor channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the controllers from Intel and Broadcom (including Apple), it is
helpful to have the information about the manufacturer send out early.
This patch sets the hdev->manufacturer information which will be send
out before actually calling the vendor specific hdev->setup driver
callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Apple Bluetooth devices, read the USB product information and
print them. This allows for easy mapping of chip and USB details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The calculation for the firmware version number is off by one bit.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Wei-Ning Huang