Manuel Lauss <manuel.lauss@gmail.com> writes:
I introduced it as a fallback because early revisions of Alchemy hardware
we shipped had a non-functional 32kHz timer and had to rely on the r4k
timer instead. Previously the r4k timer was initialized regardless, but
it's useless with the "wait" instruction.
So long story short: I need either the on-chip 32kHz timer OR the r4k
timer if the 32kHz one is unusable, but not both, and r4k timer is useless
when au1k_idle is in use.
The current in-kernel Alchemy boards all work with the 32kHz timer, so I'm
not against removing R4K_LIB symbols.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
The correct syntax for gcc -x is "gcc -x assembler", not
"gcc -xassembler". Even though the latter happens to work, the former
is what is documented in the manual page and thus what gcc wrappers
such as icecream do expect.
This isn't a cosmetic change. The missing space prevents icecream from
recognizing compilation tasks it can't handle, leading to silent kernel
miscompilations.
Besides me, credits go to Michael Matz and Dirk Mueller for
investigating the miscompilation issue and tracking it down to this
incorrect -x parameter syntax.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Cc: Bernhard Walle <bernhard@bwalle.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Use the mapping of Elf_[SPE]hdr, Elf_Addr, Elf_Sym, Elf_Dyn, Elf_Rel/Rela,
ELF_R_TYPE() and ELF_R_SYM() to either the 32-bit version or the 64-bit version
into asm-generic/module.h for all arches bar MIPS.
Also, use the generic definition mod_arch_specific where possible.
To this end, I've defined three new config bools:
(*) HAVE_MOD_ARCH_SPECIFIC
Arches define this if they don't want to use the empty generic
mod_arch_specific struct.
(*) MODULES_USE_ELF_RELA
Arches define this if their modules can contain RELA records. This causes
the Elf_Rela mapping to be emitted and allows apply_relocate_add() to be
defined by the arch rather than have the core emit an error message.
(*) MODULES_USE_ELF_REL
Arches define this if their modules can contain REL records. This causes
the Elf_Rel mapping to be emitted and allows apply_relocate() to be
defined by the arch rather than have the core emit an error message.
Note that it is possible to allow both REL and RELA records: m68k and mips are
two arches that do this.
With this, some arch asm/module.h files can be deleted entirely and replaced
with a generic-y marker in the arch Kbuild file.
Additionally, I have removed the bits from m32r and score that handle the
unsupported type of relocation record as that's now handled centrally.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fixes build failure introduced by "Make most arch asm/module.h files use
asm-generic/module.h" by moving all the RELA processing code to a
separate file to be used only for RELA processing on 64-bit kernels.
CC arch/mips/kernel/module.o
arch/mips/kernel/module.c:250:14: error: 'reloc_handlers_rela' defined but not
used [-Werror=unused-variable]
cc1: all warnings being treated as errors
make[6]: *** [arch/mips/kernel/module.o] Error 1
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
R4K-style CPUs have this boolean defined by default. Allows us
to remove some lines in arch/mips/kernel/Makefile.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/3330/
Signed-off-by: John Crispin <blogic@openwrt.org>
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Make the linker script align the task on THREAD_SIZE and not on
PAGE_SIZE, as PAGE_SIZE might be smaller than THREAD_SIZE.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20120503085034.941344764@linutronix.de
Initial commit of BMIPS SMP support code. Smoke-tested on a variety of
BMIPS4350, BMIPS4380, and BMIPS5000 platforms.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2977/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The contents of arch/mips/kernel/perf_event.c and
arch/mips/kernel/perf_event_mipsxx.c were divided in a seemingly ad
hoc manner, with the first including the second.
I moved all the hardware counter support code to perf_event_mipsxx.c
and removed the gating #ifdefs to the Kconfig and Makefile.
Now perf_event.c contains only the callchain support, everything else
is in perf_event_mipsxx.c
There are no code changes, only moving of functions from one file to
the other, or removing empty unneeded functions.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dezhong Diao <dediao@cisco.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2791/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add NLM_XLR_BOARD, CPU_XLR and other config options
Makefile updates, mostly based on r4k
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In order not to be left behind, we add jump label support for MIPS.
Tested on 64-bit big endian (Octeon), and 32-bit little endian
(malta/qemu).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/1923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a generic solution to support multiple machines based on
a given SoC within a single kernel image. It is implemented already for
several other architectures but MIPS has no generic support for that yet.
[Ralf: This competes with DT but DT is a much more complex solution and this
code has been used by OpenWRT for a long time so for now DT is a bad reason
to stop the merge but longer term this should be migrated to DT.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kaloz@openwrt.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch provides the skeleton of the HW perf event support. To enable
this feature, we can not choose the SMTC kernel; Oprofile should be
disabled; kernel performance events be selected. Then we can enable it in
Kernel type menu.
Oprofile for MIPS platforms initializes irq at arch init time. Currently
we do not change this logic to allow PMU reservation.
If a platform has EIC, we can use the irq base and perf counter irq offset
defines for the interrupt controller in specific init_hw_perf_events().
Based on this skeleton patch, the 3 different kinds of MIPS PMU, namely,
mipsxx/loongson2/rm9000, can be supported by adding corresponding lower
level C files at the bottom. The suggested names of these files are
perf_event_mipsxx.c/perf_event_loongson2.c/perf_event_rm9000.c. So, for
example, we can do this by adding "#include perf_event_mipsxx.c" at the
bottom of perf_event.c.
In addition, PMUs with 64bit counters are also considered in this patch.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: ddaney@caviumnetworks.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1688/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the ability to enable CONFIG_OF on the MIPS architecture.
Signed-off-by: Dezhong Diao <dediao@cisco.com>
[grant.likely@secretlab.ca: cleared out obsolete hooks,
removed ARCH_HAS_DEVTREE_MEM,
remove __init tags from header file,
removed debugfs support hunk]
[ddaney@linux-mips.org: backed out over aggressive trimming of hooks]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding subdirs-ccflags-y := -Werror to arch/mips/Kbuild
let us in one go cover all files with -Werror.
In addition this allows us to remove the
individual -Werror definition in various Makefile.
Adding the definition to Kbuild as a recursive
option help us not to forget to do so.
With this change we now compile arch/mips/kernel/cpufreq with -Werror
One drawback:
When specifying a subdirectory covered by the Kbuild file like this:
make arch/mips/kernel/
then kbuild fails to pick up the -Werror definition.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1301/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a preliminary patch to add a vdso to all user processes. Still
missing are ELF headers and .eh_frame information. But it is enough to
allow us to move signal trampolines off of the stack. Note that emulation
of branch delay slots in the FPU emulator still requires the stack.
We allocate a single page (the vdso) and write all possible signal
trampolines into it. The stack is moved down by one page and the vdso is
mapped into this space.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/975/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is just a test program for raw_spinlocks. The main reason I
wrote it is to validate my spinlock changes that I sent in a previous
patch.
To use it enable CONFIG_DEBUG_FS and CONFIG_SPINLOCK_TEST then at run
time do:
# mount -t debugfs none /sys/kernel/debug/
# cat /sys/kernel/debug/mips/spin_single
# cat /sys/kernel/debug/mips/spin_multi
On my 600MHz octeon cn5860 (16 CPUs) I get
spin_single spin_multi
base 106885 247941
spinlock_patch 75194 219465
This shows that for uncontended locks the spinlock patch gives 41%
improvement and for contended locks 12% improvement (1/time).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/969/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With dynamic function tracer, by default, _mcount is defined as an
"empty" function, it returns directly without any more action . When
enabling it in user-space, it will jump to a real tracing
function(ftrace_caller), and do the real job for us.
Differ from the static function tracer, dynamic function tracer provides
two functions ftrace_make_call()/ftrace_make_nop() to enable/disable the
tracing of some indicated kernel functions(set_ftrace_filter).
In the -v4 version, the implementation of this support is basically the same as
X86 version does: _mcount is implemented as an empty function and ftrace_caller
is implemented as a real tracing function respectively.
But in this version, to support module tracing with the help of
-mlong-calls in arch/mips/Makefile:
MODFLAGS += -mlong-calls.
The stuff becomes a little more complex. We need to cope with two
different type of calling to _mcount.
For the kernel part, the calling to _mcount(result of "objdump -hdr
vmlinux"). is like this:
108: 03e0082d move at,ra
10c: 0c000000 jal 0 <fpcsr_pending>
10c: R_MIPS_26 _mcount
10c: R_MIPS_NONE *ABS*
10c: R_MIPS_NONE *ABS*
110: 00020021 nop
For the module with -mlong-calls, it looks like this:
c: 3c030000 lui v1,0x0
c: R_MIPS_HI16 _mcount
c: R_MIPS_NONE *ABS*
c: R_MIPS_NONE *ABS*
10: 64630000 daddiu v1,v1,0
10: R_MIPS_LO16 _mcount
10: R_MIPS_NONE *ABS*
10: R_MIPS_NONE *ABS*
14: 03e0082d move at,ra
18: 0060f809 jalr v1
In the kernel version, there is only one "_mcount" string for every
kernel function, so, we just need to match this one in mcount_regex of
scripts/recordmcount.pl, but in the module version, we need to choose
one of the two to match. Herein, I choose the first one with
"R_MIPS_HI16 _mcount".
and In the kernel verion, without module tracing support, we just need
to replace "jal _mcount" by "jal ftrace_caller" to do real tracing, and
filter the tracing of some kernel functions via replacing it by a nop
instruction.
but as we have described before, the instruction "jal ftrace_caller" only left
32bit length for the address of ftrace_caller, it will fail when calling from
the module space. so, herein, we must replace something else.
the basic idea is loading the address of ftrace_caller to v1 via changing these
two instructions:
lui v1,0x0
addiu v1,v1,0
If we want to enable the tracing, we need to replace the above instructions to:
lui v1, HI_16BIT_ftrace_caller
addiu v1, v1, LOW_16BIT_ftrace_caller
If we want to stop the tracing of the indicated kernel functions, we
just need to replace the "jalr v1" to a nop instruction. but we need to
replace two instructions and encode the above two instructions
oursevles.
Is there a simpler solution? Yes! Here it is, in this version, we put _mcount
and ftrace_caller together, which means the address of _mcount and
ftrace_caller is the same:
_mcount:
ftrace_caller:
j ftrace_stub
nop
...(do real tracing here)...
ftrace_stub:
jr ra
move ra, at
By default, the kernel functions call _mcount, and then jump to ftrace_stub and
return. and when we want to do real tracing, we just need to remove that "j
ftrace_stub", and it will run through the two "nop" instructions and then do
the real tracing job.
what about filtering job? we just need to do this:
lui v1, hi_16bit_of_mcount <--> b 1f (0x10000004)
addiu v1, v1, low_16bit_of_mcount
move at, ra
jalr v1
nop
1f: (rec->ip + 12)
In linux-mips64, there will be some local symbols, whose name are
prefixed by $L, which need to be filtered. thanks goes to Steven for
writing the mips64-specific function_regex.
In a conclusion, with RISC, things becomes easier with such a "stupid"
trick, RISC is something like K.I.S.S, and also, there are lots of
"simple" tricks in the whole ftrace support, thanks goes to Steven and
the other folks for providing such a wonderful tracing framework!
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/675/
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If -pg of gcc is enabled with CONFIG_FUNCTION_TRACER=y. a calling to
_mcount will be inserted into each kernel function. so, there is a
possibility to trace the kernel functions in _mcount.
This patch add the MIPS specific _mcount support for static function
tracing. by default, ftrace_trace_function is initialized as
ftrace_stub(an empty function), so, the default _mcount will introduce
very little overhead. after enabling ftrace in user-space, it will jump
to a real tracing function and do static function tracing for us.
and -ffunction-sections is incompatible with -pg, so, disable it when
ftracer is enabled.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson 2F supports CPU clock scaling. When put it into wait mode by
setting the frequency as ZERO it will stay in this mode until an external
interrupt wakes the CPU again.
To enable clock scaling support, an external timer of a known stable rate
is required.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cpufreq@vger.kernel.org,
Cc: Dave Jones <davej@redhat.com>,
Cc: Dominik Brodowski <linux@dominikbrodowski.net>,
Cc: yanh@lemote.com
Cc: huhb@lemote.com,
Patchwork: http://patchwork.linux-mips.org/patch/660/
Patchwork: http://patchwork.linux-mips.org/patch/751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the Cisco Powertv cable settop box to the MIPS tree. This platform is
based on a MIPS 24Kc processor with various devices integrated on the same
ASIC. There are multiple models of this box, with differing configuration
but the same kernel runs across the product line.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 51b563fc93 ("arm, cris, mips,
sparc, powerpc, um, xtensa: fix build with bash 4.0") removed a few
CPPFLAGS with vital include paths necessary to build vmlinux.lds
on MIPS, and moved the calculation of the 'jiffies' symbol
directly to vmlinux.lds.S but forgot to change make ifdef/... to
cpp macros.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
[sam: moved assignment of CPPFLAGS arch/mips/kernel/Makefile]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
The current mips clock build infrastructure lets a system only use
either the MIPS cp0 counter or a SoC specific timer as a clocksource /
clockevent device.
This patch renames the core cp0 counter clocksource / clockevent functions
from mips_* to r4k_* and updates the wrappers in asm-mips/time.h to
call these renamed functions instead.
Chips which can detect whether it is safe to use a chip-specific timer
can now fall back on the cp0 counter if necessary and possible
(e.g. Alchemy with a follow-on patch).
Existing behaviour is not changed in any way.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Take all the OCTEON specific files that were added, and hook them into
the build system for the arch/mips. For versions of GCC that lack
OCTEON support, override gas target architecture.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We already have sufficient infrastructure to support VR5500 and VR5500A
series processors. Here's a Makefile support to make it selectable by
ports, and enable it for NEC EMMA2RH Markeins board.
This patch also fixes a confused target help, and adds 1Gb PageMask bits
supported by VR5500 and its variants.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the main support code for the patch. Here we just add the
code, the following patches hook it up.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/include/asm/watch.h
create mode 100644 arch/mips/kernel/watch.c
Rework of SMTC support to make it work with the new clock event system,
allowing "tickless" operation, and to make it compatible with the use of
the "wait_irqoff" idle loop. The new clocking scheme means that the
previously optional IPI instant replay mechanism is now required, and has
been made more robust.
Signed-off-by: Kevin D. Kissell <kevink@paralogos.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The new kgdb architecture specific handler registers and unregisters
dynamically for exceptions depending on when you configure a kgdb I/O
driver.
Aside from initializing the exceptions earlier in the boot process,
kgdb should have no impact on a device when it is compiled in so long
as an I/O module is not configured for use.
There have been quite a number of contributors during the existence of
this patch (see arch/mips/kernel/kgdb.c). Most recently Jason
re-wrote the mips kgdb logic to use the die notification handlers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch explicitly removes the kgdb implementation, for mips which
is intended to be followed by a patch that adds a kgdb implementation
for MIPS that makes use of the kgdb core in the kernel.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Never terribly functional or popular, plagued by hard to fix bugs the time
to say goodbye has more than arrived.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The existing options are named CONFIG_CPU_R4300 and CONFIG_CPU_R4X00,
and they are directly below.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a board-independent TXx9 gpio API implementation using gpiolib.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
In particular as-is it's not suited for multicore and mutiprocessors
systems where there is on guarantee that the counter are synchronized
or running from the same clock at all. This broke Sibyte and probably
others since the "[MIPS] Handle R4000/R4400 mfc0 from count register."
commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Steven J. Hill