At least on Lenovo Thinkpad Yoga, the BIOS seems to monitor the SPI-NOR
write protection bit and if it is flipped to read/write it assumes the
BIOS configuration was changed on next reboot. It then, for unknown
reasons, resets the BIOS settings back to default.
We can prevent this by just leaving the write protection bit intact and
let the SPI-NOR driver know whether the device is writable or not. In
case of this particular Lenovo the SPI-NOR flash will be exposed as
read-only.
Fixes: ff00d7a32a ("mfd: lpc_ich: Add support for SPI serial flash host controller")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195951
Reported-by: Abdó Roig-Marange <abdo.roig@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22e ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to their datasheets, the AXP221, AXP223, AXP288, AXP803,
AXP809 and AXP813 PEK have different values for startup time bits from
the AXP20X, let's use the platform device id with the correct values.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP813 PMIC is normally used with Allwinner's A83T SoC.
It has the same range of functions as other X-Powers PMICs, such as
DC-DC buck converter and linear regulator outputs, AC-IN and VBUS
power supplies, power button trigger, GPIOs, ADCs, and a battery
charger.
Note that the IRQ table given in the datasheet is incorrect: in IRQ
enable/status registers 1, there are separate IRQs for ACIN and VBUS,
instead of bits [7:5] being the same as bits [4:2]. So it shares the
same IRQs as the AXP803, rather than the AXP288.
This patch adds basic mfd support for it, with only the power button
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the MFD part of the ROHM BD9571MWV-M PMIC driver and MAINTAINERS
entry. The MFD part only specifies the regmap bits for the PMIC and
binds the subdevs together.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for HiSilicon Hi6421v530 PMIC. Hi6421v530 communicates with
main SoC via memory-mapped I/O.
Hi6421v530 and Hi6421 are PMIC chips from the same vendor, HiSilicon,
but at different revisions. They share the same memory-mapped I/O
design. They differ in integrated devices, such as regulator details,
LDO voltage points.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update dev_err messages to make them more readable.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change license text to a shorter form of GPLv2.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MTF_CORE should be enabled when driver is enabled.
Without this patch you can configure:
CONFIG_MFD_CORE is not set
CONFIG_MFD_TPS65086=y
... which ends up with compilation error:
drivers/mfd/tps65086.o: In function `tps65086_probe':
drivers/mfd/tps65086.c:110: undefined reference to `mfd_add_devices'
drivers/mfd/tps65086.c:110:(.text+0x128): relocation truncated to fit: \
R_AARCH64_CALL26 against undefined symbol `mfd_add_devices'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
16298 1009 184 17491 4453 drivers/mfd/ab8500-core.o
File size After adding 'const':
text data bss dec hex filename
16490 817 184 17491 4453 drivers/mfd/ab8500-core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
if 'max8998_i2c_parse_dt_pdata() fails (when out of memory), a NULL
pointer dereference will occur in the error handling code.
Return directly instead.
Fixes: ee999fb3f17f("mfd: max8998: Add support for Device Tree")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Drop static on a local variable, when the variable is initialized before
any use, on every possible execution path through the function. The static
has no benefit, and dropping it reduces the code size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
2579 240 16 2835 b13 drivers/mfd/max8925-i2c.o
after:
text data bss dec hex filename
2531 240 8 2779 adb drivers/mfd/max8925-i2c.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible that under heavy system load, the counter in the completion
struct, used for waiting for end of AD conversion, gets incremented twice.
To make sure the driver recovers from this situation, the completion struct
should be reinitialized.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't populate the arrays depath and cd_mask on the stack but make
them static const. Makes the object code smaller:
text data bss dec hex filename
25413 7216 448 33077 8135 drivers/mfd/rtsx_pcr.o
text data bss dec hex filename
25151 7360 448 32959 80bf drivers/mfd/rtsx_pcr.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Saying it "returns the result" seems tautological. The read function
does not return num_bytes on success, it returns zero on success. I
noticed this discrepancy because some of the callers were checking for
>= 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 Low-Power Timer hardware block can be used for:
- PWM generation
- IIO trigger (in sync with PWM)
- IIO quadrature encoder counter
PWM and IIO timer configuration are mixed in the same registers so
we need a multi fonction driver to be able to share those registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A small number of bugfixes, again nothing serious.
- Alexander Dahl found multiple bugs in the Atmel memory interface driver
- A randconfig build fix for at91 was incomplete, the second
attempt fixes the remaining corner case
- One fix for the TI Keystone queue handler
- The Odroid XU4 HDMI port (added in 4.13) needs a small
DT fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=efYA
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A small number of bugfixes, again nothing serious.
- Alexander Dahl found multiple bugs in the Atmel memory interface
driver
- A randconfig build fix for at91 was incomplete, the second attempt
fixes the remaining corner case
- One fix for the TI Keystone queue handler
- The Odroid XU4 HDMI port (added in 4.13) needs a small DT fix"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: add needs-hpd for Odroid-XU3/4
ARM: at91: don't select CONFIG_ARM_CPU_SUSPEND for old platforms
soc: ti: knav: Add a NULL pointer check for kdev in knav_pool_create
memory: atmel-ebi: Fix smc cycle xlate converter
memory: atmel-ebi: Allow t_DF timings of zero ns
memory: atmel-ebi: Fix smc timing return value evaluation
This patch was applied to the MFD twice, causing unwanted behavour.
This reverts commit b77eb79acc.
Fixes: b77eb79acc ("mfd: da9061: Fix to remove BBAT_CONT register from chip model")
Reported-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the touchscreen pins are used as general purpose analogue
input, the touchscreen driver should not be used. The pins
will be handled by the existing hwmon driver instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK805 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clocking
Both RK808 and RK805 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
the rk8xx chip id is:
((MSB << 8) | LSB) & 0xfff0
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The converter function for translating ns timings in register values was
initialized with a wrong function pointer. This resulted in wrong
register values also for the setup and pulse registers when configuring
the EBI interface trough dts.
Includes a small fix in a comment of the smc driver, which was probably
just a copy'n'paste mistake.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have a
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have a
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's not correct to encode the subsystem in the I2C device name, so
drop the -mfd suffix. To maintain bisect-ability, change driver and
platform code / DTS users in the same patch.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Changes in this pull request are around catching up
cros_ec with the internal chromeos-kernel versions of
cros_ec, cros_ec_lpc, and cros_ec_lightbar.
Also, switching maintainership from olof to bleung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QtSr
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
"Changes in this pull request are around catching up cros_ec with the
internal chromeos-kernel versions of cros_ec, cros_ec_lpc, and
cros_ec_lightbar.
Also, switching maintainership from olof to bleung"
* tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome : Add myself as Maintainer
platform/chrome: cros_ec_lightbar - hide unused PM functions
cros_ec: Don't signal wake event for non-wake host events
cros_ec: Fix deadlock when EC is not responsive at probe
cros_ec: Don't return error when checking command version
platform/chrome: cros_ec_lightbar - Avoid I2C xfer to EC during suspend
platform/chrome: cros_ec_lightbar - Add userspace lightbar control bit to EC
platform/chrome: cros_ec_lightbar - Control of suspend/resume lightbar sequence
platform/chrome: cros_ec_lightbar - Add lightbar program feature to sysfs
platform/chrome: cros_ec_lpc: Add MKBP events support over ACPI
platform/chrome: cros_ec_lpc: Add power management ops
platform/chrome: cros_ec_lpc: Add support for GOOG004 ACPI device
platform/chrome: cros_ec_lpc: Add support for mec1322 EC
platform/chrome: cros_ec_lpc: Add R/W helpers to LPC protocol variants
mfd: cros_ec: Add support for dumping panic information
cros_ec_debugfs: Pass proper struct sizes to cros_ec_cmd_xfer()
mfd: cros_ec: add debugfs, console log file
mfd: cros_ec: Add EC console read structures definitions
mfd: cros_ec: Add helper for event notifier.
Pull input updates from Dmitry Torokhov:
- a new driver for STM FingerTip touchscreen
- a new driver for D-Link DIR-685 touch keys
- updated list of supported devices in xpad driver
- other assorted updates and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (23 commits)
MAINTAINERS: update input subsystem patterns
Input: introduce KEY_ASSISTANT
Input: xpad - sync supported devices with XBCD
Input: xpad - sync supported devices with 360Controller
Input: xen-kbdfront - use string constants from PV protocol
Input: stmfts - mark all PM functions as __maybe_unused
Input: add support for the STMicroelectronics FingerTip touchscreen
Input: add D-Link DIR-685 touchkeys driver
Input: s3c2410_ts - handle return value of clk_prepare_enable
Input: axp20x-pek - add wakeup support
Input: synaptics-rmi4 - use %phN to form F34 configuration ID
Input: synaptics-rmi4 - change a char type to u8
Input: sparse-keymap - remove sparse_keymap_free()
Input: tsc2007 - move header file out of I2C realm
Input: mms114 - move header file out of I2C realm
Input: mcs - move header file out of I2C realm
Input: lm8323 - move header file out of I2C realm
Input: elantech - force relative mode on a certain module
Input: elan_i2c - add support for fetching chip type on newer hardware
Input: elan_i2c - check if device is there before really probing
...
Pull MFD updates from Lee Jones:
"New Drivers:
- Intel Cherry Trail Whiskey Cove PMIC
- TI LP87565 PMIC
New Device Support:
- Add support for Cannonlake to intel-lpss-pci
- Add support for Simatic IOT2000 to intel_quark_i2c_gpio
New Functionality:
- Add Regulator support (axp20x)
Fix-ups:
- Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec)
- Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core)
- Provide deregistration on unbind (rn5t618)
- Rework DT code/documentation (arizona)
- Constify things (fsl-imx25-tsadc)
- MAINTAINERS updates (DA9062/61)
- Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C)
- Switch to DMI matching (intel_quark_i2c_gpio)
- Provide an appropriate level of error checking (wm831x-{i2c,spi},
twl4030-irq, tc6393xb)
- Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc,
stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc,
exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099,
motorola-cpcap)"
[ Skipped the last commit in that series that added eight thousand
lines of pointless repeated register definitions. - Linus ]
* tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits)
mfd: Add LP87565 PMIC support
mfd: cros_ec: Free IRQ on exit
dt-bindings: vendor-prefixes: Add arctic to vendor prefix
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: axp20x-i2c: Document that this must be builtin on x86
mfd: Add Cherry Trail Whiskey Cove PMIC driver
mfd: tc6393xb: Handle return value of clk_prepare_enable
mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform
mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency
mfd: motorola-cpcap: Use devm_of_platform_populate()
mfd: smsc-ece: Use devm_of_platform_populate()
mfd: qcom-spmi-pmic: Use devm_of_platform_populate()
mfd: palmas: Use devm_of_platform_populate()
mfd: exynos: Use devm_of_platform_populate()
mfd: fsl-imx25: Use devm_of_platform_populate()
mfd: cros_ec: Use devm_of_platform_populate()
mfd: atmel: Use devm_of_platform_populate()
mfd: stm32-timers: Use devm_of_platform_populate()
mfd: intel_soc_pmic: Select designware i2c-bus driver
...
The LP87565 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Configurable Bucks(Single and multi-phase).
- Configurable General Purpose Output Signals (GPO).
The LP87565-Q1 variant device uses two 2-phase outputs configuration,
Buck0 is master for Buck0/1 output and Buck2 is master for Buck2/3
output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently we request the irq when probing, but never free it. So after
unbind ec driver, this irq will be left requested, which would break
the next bind:
[ 2683.338437] genirq: Flags mismatch irq 64. 00002008 (chromeos-ec) vs. 00002008 (chromeos-ec)
[ 2683.338591] cros-ec-spi spi5.0: request irq 64: error -16
[ 2683.338610] cros-ec-spi spi5.0: cannot register EC
[ 2683.338656] cros-ec-spi: probe of spi5.0 failed with error -16
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On x86 the AXP288 PMIC provides an ACPI OpRegion handler, which must be
available before other drivers using it are loaded, which can only be
ensured if the MFD, OpRegion and i2c-bus drivers are built-in.
Since the AXP20x MFD code is used on non x86 too we cannot simply change
this into a bool, I've tried some Kconfig magic with if x86 but I could
not get this working correctly, so this commit just documents that this
should be built-in on x86, which fixes errors like these during boot:
mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion]
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-2
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b
acpi 80860F14:02: Failed to change power state to D0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add mfd driver for Intel CHT Whiskey Cove PMIC, based on various non
upstreamed CHT Whiskey Cove PMIC patches.
This is a somewhat minimal version which adds irqchip support and cells
for: ACPI PMIC opregion support, the i2c-controller driving the external
charger irc and the pwrsrc/extcon block.
Further cells can be added in the future if/when drivers are upstreamed
for them.
[The above patch caused a build error on some archetectures]
From: Arnd Bergmann <arnd@arndb.de>
I ran into a build error on ARM with a platform that has a non-standard
clk implementation:
drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.
This turns all three into 'depends on', as it should be.
Finally, we can limit the build to x86, unless we are compile testing.
First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The SIMATIC IOT2020 and IOT2040 are derived from the Galileo Gen2 board
and share its I2C frequency.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Avoids reimplementation of DMI matching in intel_quark_i2c_setup.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Usage of devm_of_platform_populate() simplify driver code
by allowing to delete cpcap_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Usage of devm_of_platform_populate() simplify driver code
by allowing to delete pmic_spmi_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
