Commit graph

25 commits

Author SHA1 Message Date
Giuseppe Cavallaro
0f0ca340e5 phy: power management support
This patch adds the power management support into the physical
abstraction layer.

Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.

In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.

Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).

Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-28 16:24:56 -08:00
Lennert Buytenhek
2e88810329 phylib: add mdiobus_{read,write}
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 16:38:41 -07:00
Lennert Buytenhek
46abc02175 phylib: give mdio buses a device tree presence
Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 16:33:40 -07:00
Lennert Buytenhek
298cf9beb9 phylib: move to dynamic allocation of struct mii_bus
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-10-08 16:29:57 -07:00
Lennert Buytenhek
18ee49ddb0 phylib: rename mii_bus::dev to mii_bus::parent
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-10-08 16:27:49 -07:00
Lennert Buytenhek
4fd5f812c2 phylib: allow incremental scanning of an mii bus
This patch splits the bus scanning code in mdiobus_register() off
into a separate function, and makes this function available for
calling from external code.  This allows incrementally scanning an
mii bus, e.g. as information about which addresses are 'safe' to
scan becomes available.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-09-19 05:13:54 +02:00
Andy Fleming
9b9a8bfc8d phylib: Fix some sparse warnings
Declared some things static, declared some things in the header.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 12:01:41 -04:00
Andy Fleming
f62220d3a9 phylib: Add support for board-level PHY fixups
Sometimes the specific interaction between the platform and the PHY
requires special handling.  For instance, to change where the PHY's
clock input is, or to add a delay to account for latency issues in the
data path.  We add a mechanism for registering a callback with the PHY
Lib to be called on matching PHYs when they are brought up, or reset.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 02:08:52 -04:00
Paul Gortmaker
cac1f3c8a8 phylib: factor out get_phy_id from within get_phy_device
We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:31:33 -04:00
Andy Fleming
c5e38a949b phy: Clean up header style
Multi-line comments weren't all CodingStyle compliant

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16 20:09:35 -04:00
Andy Fleming
9d9326d3bc phy: Change mii_bus id field to a string
Having the id field be an int was making more complex bus topologies
excessively difficult.  For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-16 20:09:35 -04:00
Nate Case
35b5f6b1a8 PHYLIB: Locking fixes for PHY I/O potentially sleeping
PHY read/write functions can potentially sleep (e.g., a PHY accessed
via I2C).  The following changes were made to account for this:

    * Change spin locks to mutex locks
    * Add a BUG_ON() to phy_read() phy_write() to warn against
      calling them from an interrupt context.
    * Use work queue for PHY state machine handling since
      it can potentially sleep
    * Change phydev lock from spinlock to mutex

Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:41 -08:00
Anton Vorontsov
6f4a7f4183 PHY: Add the phy_device_release device method.
Lately I've got this nice badness on mdio bus removal:

Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700   Not tainted  (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR>  CR: 24088422  XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...

Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.

This patch implement phy device's release function, thus
we're getting rid of this badness.

Also small hidden bug fixed, hope none other introduced. ;-)

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-04 15:06:33 -05:00
Kim Phillips
7d400a4c58 phylib: add PHY interface modes for internal delay for tx and rx only
Allow phylib specification of cases where hardware needs to configure
PHYs for Internal Delay only on either RX or TX (not both).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-01 16:32:30 -05:00
Maciej W. Rozycki
0ac4952731 PHYLIB: IRQ event workqueue handling fixes
Keep track of disable_irq_nosync() invocations and call enable_irq() the
right number of times if work has been cancelled that would include them.

Now that the call to flush_work_keventd() (problematic because of
rtnl_mutex being held) has been replaced by cancel_work_sync() another
issue has arisen and been left unresolved.  As the MDIO bus cannot be
accessed from the interrupt context the PHY interrupt handler uses
disable_irq_nosync() to prevent from looping and schedules some work to be
done as a softirq, which, apart from handling the state change of the
originating PHY, is responsible for reenabling the interrupt.  Now if the
interrupt line is shared by another device and a call to the softirq
handler has been cancelled, that call to enable_irq() never happens and the
other device cannot use its interrupt anymore as its stuck disabled.

I decided to use a counter rather than a flag because there may be more
than one call to phy_change() cancelled in the queue -- a real one and a
fake one triggered by free_irq() if DEBUG_SHIRQ is used, if nothing else.
Therefore because of its nesting property enable_irq() has to be called the
right number of times to match the number disable_irq_nosync() was called
and restore the original state.  This DEBUG_SHIRQ feature is also the
reason why free_irq() has to be called before cancel_work_sync().

While at it I updated the comment about phy_stop_interrupts() being called
from `keventd' -- this is no longer relevant as the use of
cancel_work_sync() makes such an approach unnecessary.  OTOH a similar
comment referring to flush_scheduled_work() in phy_stop() still applies as
using cancel_work_sync() there would be dangerous.

Checked with checkpatch.pl and at the run time (with and without
DEBUG_SHIRQ).

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:53:55 -07:00
Kim Phillips
a999589cca phylib: add RGMII-ID interface mode definition
The RGMII spec allows compliance for devices that implement an internal
delay on TXC or RXC inside the transmitter.  This patch adds an RGMII_ID
definition to support RGMII-ID devices in the phylib.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 11:01:04 -04:00
Andy Fleming
e8a2b6a420 [PATCH] PHY: Add support for configuring the PHY connection interface
Most PHYs connect to an ethernet controller over a GMII or MII
interface.  However, a growing number are connected over
different interfaces, such as RGMII or SGMII.

The ethernet driver will tell the PHY what type of connection it
is by setting it manually, or passing it in through phy_connect
(or phy_attach).

Changes include:
* Updates to documentation
* Updates to PHY Lib consumers
* Changes to PHY Lib to add interface support
* Some minor changes to whitespace in phy.h
* gianfar driver now detects interface and passes appropriate
  value to PHY Lib
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:33:11 -05:00
Maciej W. Rozycki
13df29f697 [PATCH] 2.6.18: sb1250-mac: Missing inclusions from <linux/phy.h>
The <linux/phy.h> uses some types and macros defined in
<linux/ethtool.h>, <linux/mii.h>, <linux/timer.h> and <linux/workqueue.h>,
but fails to include these headers.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>

patch-mips-2.6.18-20060920-include-phy-16
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02 00:11:55 -05:00
Vitaly Bordug
11b0bacd71 [PATCH] PAL: Support of the fixed PHY
This makes it possible for HW PHY-less boards to utilize PAL goodies.  Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc.  information into PHY
descriptor (the latter feature not tested so far).

Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-19 17:44:31 -04:00
Kumar Gala
a4d00f179f [PATCH] phy: Added a macro to represent the string format used to match a phy device
Add the PHY_ID_FMT macro to ensure that the format of the id string used by a
driver to match to its specific phy is consistent between the mdio_bus and the
driver.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2006-01-12 16:31:52 -05:00
Matt Porter
f896424cbc [PATCH] phy address mask support for generic phy layer
Adds a phy_mask field to struct mii_bus and uses it.  This field
indicates each phy address to be ignored when probing the mdio bus.

This support is needed for the fs_enet and ibm_emac drivers to be
converted to the generic phy layer among other drivers. Many systems
lock up on probing certain phy addresses or probing doesn't return
0xffff when nothing is found at the address. A new driver I'm
working on also makes use of this mask.

Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-11-05 14:40:55 -05:00
Andy Fleming
e13934563d [PATCH] PHY Layer fixup
This patch adds back the code that was taken out, thus re-enabling:

* The PHY Layer to initialize without crashing
* Drivers to actually connect to PHYs
* The entire PHY Control Layer

This patch is used by the gianfar driver, and other drivers which are in
development.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-08-28 20:28:25 -04:00
Jeff Garzik
2bf69b5fe9 phy subsystem: more cleanups
- unexport symbols never used outside of home module
- remove dead code
- remove CONFIG_PHYCONTROL, make it unconditionally enabled
2005-08-11 02:47:54 -04:00
Jeff Garzik
67c4f3fa25 Fix numerous minor problems with new phy subsystem.
Includes fixes for problems noted by Adrian Bunk, Andrew Morton,
and one other person lost in the annals of history (and email folders).
2005-08-11 02:07:25 -04:00
Andy Fleming
00db8189d9 This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-30 19:31:23 -04:00