The memory allocator is being initialized before registering the subdevs
so reverse the cleanup sequence to avoid trying unregister not registered
subdevs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure the device also works when runtime PM is disabled.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Devices should also operate normally when runtime PM is not enabled.
In case runtime PM is disabled activate the device already in probe().
Any related power domain needs to be then left permanently in active
state by the platform.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver should ensure a device can be also used normally when runtime
PM is disabled. So enable the FIMC clock in probe() in such situation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver for Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with
embedded SoC ISP. The device is exposed as two V4L2 subdevices:
- S5K5BAF-CIS - the image sensor matrix, fixed 1600x1200 format,
no controls.
- S5K5BAF-ISP - the Image Signal Processor, formats up to 1600x1200,
pre/post ISP cropping, downscaling via selection API, controls.
[m.chehab@samsung.com: Whitespace cleanups]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot <fengguang.wu@intel.com>:
> warning: (VIDEO_EM28XX_DVB) selects DVB_M88DS3103 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CORE && I2C && I2C_MUX)
> drivers/built-in.o: In function `m88ds3103_release':
> >> m88ds3103.c:(.text+0x1ab1af): undefined reference to `i2c_del_mux_adapter'
> drivers/built-in.o: In function `m88ds3103_attach':
> >> (.text+0x1ab342): undefined reference to `i2c_add_mux_adapter'
There are 3 possible ways to fix it:
1) make em28xx dependent on I2C_MUX.
That sounds wrong, as the em28xx bridge doesn't have i2c muxes on it,
and just one frontend has.
Well, subdevs could eventually be converted to, instead of using dvb
i2c gate control, to use i2c mux support.
That makes sense, but it takes time and lots of effort. Not sure if
this will happen anytime soon.
2) MEDIA_SUBDRV_AUTOSELECT can be dependent of I2C and I2C_MUX.
That means that users will need to manually enable I2C_MUX on some
distributions. Not sure about others, but, on Fedora, this option is
disabled.
So, it can end by generating a number of complains from users
that their devices suddenly stopped working after a Kernel upgrade,
at least until all distros that ship Kernels with I2C_MUX enabled.
3) if MEDIA_SUBDRV_AUTOSELECT is selected, it will select I2C and I2C_MUX.
Of course, MEDIA_SUBDRV_AUTOSELECT will need to inherit all dependencies
that I2C and I2C_MUX have (only HAS_IOMEM).
The disadvantage is that, if new dependencies are added on I2C, they'll
also need to be added here.
As the hole idea of autoselect is to let the user not bother about whatever
frontend/tuner is used by a driver, IMHO, (3) is the better solution.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PLL was attached twice to frontend0 leaving frontend1 without a tuner.
frontend0 is DVB-C and frontend1 is DVB-T.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For GPI-connected buttons without (hardware) debouncing, the polling interval
needs to be reduced to detect button presses properly.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
During the last media summit meeting it was decided to move this driver to
staging as the first step to removing it altogether.
Most webcams covered by this driver are now supported by gspca. Nobody has the
hardware to convert the remaining devices to gspca.
This driver needs a major overhaul to have it conform to the latest frameworks
and compliancy tests.
Without hardware, however, this is next to impossible. Given the fact that
this driver seems to be pretty much unused (it has been removed from Fedora
several versions ago and nobody complained about that), we decided to drop
this driver.
This patch moves it to staging. Some time in 2014 we will drop it completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by kbuild test robot <fengguang.wu@intel.com>:
with a random config:
drivers/built-in.o: In function `dib8000_get_time_us.isra.16':
>> dib8000.c:(.text+0x3075aa): undefined reference to `__udivdi3'
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
GIT_AUTHOR_DATE=1386943312
Add USB IDs for the WinFast DTV Dongle Mini.
Device is tested and works fine under MythTV
Signed-off-by: Robert Backhaus <robbak@robbak.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Latest checkpatch.pl has some new requirements for coding style.
Fix some of those.
* remove Free Software Foundation postal address
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* remove Free Software Foundation postal address
* add one pair of parenthesis
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adapter is locked by I2C core already. Use unlocked i2c_transfer()
version __i2c_transfer() to avoid deadlock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Write inittab using reg address auto-increment in order to reduce
I/O a little bit.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reg 0x56 should be programmed to 0x01. Add default to inittab.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Optimal AGC is highly depended on used RF tuner and due to that
it is already included to chip configuration. However, inittab
has default AGC value, which was later replaced by one from config.
Add also comment to all chip configuration options about default
values and if those are needed to set or not.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Used synthesizer is very typical integer-N PLL, with configurable
reference frequency divider, output frequency divider and of
course N itself. Most common method to calculate values is first
select output divider, then calculate VCO frequency and finally
calculate PLL N from VCO frequency. Do it that way.
Also make some cleanups for filter logic and signal strength.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DIV_ROUND_CLOSEST does the job and looks better.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Switch standard I2C adapter to muxed I2C adapter.
David reported that I2C adapter implementation caused deadlock.
I discussed with Jean and he suggested to implement it as a
multiplexed i2c adapter because tuner I2C bus could be seen like
own I2C segment.
Reported-by: David Howells <dhowells@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
M88TS2022 is DVB-S/S2 RF tuner used usually in conjunction with
Montage M88DS3103 DVB-S/S2 demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PER/UCB statistics are collected once on each 1 second.
However, it doesn't provide the total number of packets
needed to calculate PER.
Yet, as we know the bit rate, it is possible to estimate
such number. So, do it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the BER statistics are updated on every 1.25e6 bits.
Adjust the code to only update the statistics after having it
done.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the block error count is a monotonic 32 bits register.
With DVBv5 stats, we use a 64 bits counter, that it is reset
when a new channel is tuned.
Change the UCB counting start from 0 and to be returned with
64 bits, just like the API requests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Use multiple linear segments to better interpolate the dBm
for the signal strength.
The table that converts from linear strength to dB was
empirically determinated with the help of a signal generator
(DTA-2111).
The entries from -35dBm to -22.5dBm were taken using just
the signal generator and the board.
For the entries from -36dBm to -51dBm, a 16 dB tap was used,
in order to extend its range.
Signals below to -51dBm are just linearly interpolated.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Better to have Signal strength in dB.
This takes a very rough estimation for the signal strength,
that was calibrated using a Dektec DTA-2111 Gold RF generator
and a Pixelview dib8076 stick.
It estimates the signal strength using a linear equation where:
- the max is -22.5 dBm, with returns 55953
- the min is -35.0 dBm, with returns 50110
With -22dBm, the signal strengh is returned as 65535.
Unfortunately, the min strength generated with DTA-2111 is
-35dBm.
It should be noticed that approximating it by a linear equation
is not right. I should probably be splitting it into 0.5 dB
linear segments, in order to get a higher precision, just like
it is done on mb86a20s, but that would force me to add some
attenuators, in order to get dB levels below -35dBm, which is,
btw, strong enough to get signal lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The advantage of DVBv5 stats is that it allows adding proper
scales to all measures. use it for this frontend.
This patch adds a basic set of stats, basically cloning what's already
provided by DVBv3 API. Latter patches will improve it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On ISDB-T, the valid values for interleaving are 0, 1, 2 and 4.
While the first 3 are properly reported, the last one is reported
as 3 instead. Fix it.
Tested with a Dektec DTA-2111 RF generator.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The logic that detects if auto search mode should be used is too
complex.
Also, it doesn't cover all cases, as the dib8000_tune logic
requires either auto mode or a fully specified manual mode.
So, move it to a separate function and add some extra debug
data to help identifying when it falled back to auto mode,
because the manual settings are invalid.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Both dvbv5-scan and dvbv5-zap tools call FE_GET_PROPERTY inside the
loop that checks for stats. If the frontend doesn't support DVBv5, it
falls back to call the DVBv5 stats APIs(FE_READ_BER, FE_READ_SIGNAL,
FE_READ_SNR and FE_READ_UNCORRECTED_BLOCKS).
A call to FE_GET_PROPERTY makes dvb-frontend core to call get_frontend().
However, due to a race condition on dib8000 between dib8000_get_frontend
and dib8000_tune, if get_frontend occurs too early, it causes the
tune state machine to fail and not get any lock.
This patch adds a workaround code that makes get_frontend() to just
return if none of the frontends have a SYNC. This change fixed the issue
with dvbv5-scan/dvbv5-zap, but a fine-tuned logic might be needed in
the future, when we implement DVBv5 stats on this frontend.
The procedure to test the bug and the fix is the one below:
1) tune into a non-existing frequency with:
$ dvbv5-zap -I dvbv5 -c non_existing_freqs -m 679142857 -t3
2) tune/lock into an existing frequency with:
$ dvbv5-zap -I dvbv5 -c isdb-test -m 479142857
or
$ dvbv5-scan isdb-test
In this case, 679 MHz carrier doesn't exist. Only 479 MHz does.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
As the dvb-frontend kthread can be called anytime, it can race
with some get status ioctl. So, it seems better to avoid one to
race with the other while reading a 32 bits register.
I can't see any other reason for having a mutex there at I2C, except
to provide such kind of protection, as the I2C core already has a
mutex to protect I2C transfers.
Note: instead of this approach, it could eventually remove the dib8000
specific mutex for it, and either group the 4 ops into one xfer or
to manually control the I2C mutex. The main advantage of the current
approach is that the changes are smaller and more puntual.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Commit 173a64cb3f broke support for some dib807x versions.
Fix it by providing backward compatibility with the older versions.
[mkrufky@linuxtv.org: conflict handling and CodingStyle fixes]
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exynos4x12 has limitations regarding setting chroma subsampling
of an output JPEG image. It cannot be lower than the subsampling
of the raw source image. Also in case of V4L2_JPEG_CHROMA_SUBSAMPLING_GRAY
option the source image fourcc has to be V4L2_PIX_FMT_GREY.
This patch implements try_ctrl callback containing mechanism that
prevents setting invalid value of the V4L2_CID_JPEG_CHROMA_SUBSAMPLING
control.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When output queue fourcc is set to any flavour of YUV,
the V4L2_CID_JPEG_CHROMA_SUBSAMPLING control value as
well as its in-driver cached counterpart have to be
updated with the subsampling property of the format
so as to be able to provide correct information to the
user space and preclude setting an illegal subsampling
mode for Exynos4x12 encoder.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adjust capture format to the Exynos4x12 device limitations,
according to the subsampling value parsed from the source
JPEG image header. If the capture format was set to YUV with
subsampling lower than the one of the source JPEG image
the decoding process would not succeed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make s5p_jpeg_parse_hdr function capable of parsing
"YCbCr subsampling" field of a jpeg file header. Store the
parsed value in the context.
The information about source JPEG subsampling is required to
make validation of destination format possible, which must be
conducted for exynos4x12 device as the decoding process will
not succeed if the destination format is set to YUV with
subsampling lower than the one of the source JPEG image.
With this knowledge the driver can adjust the destination format
appropriately.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add hardware API for the exynos4x12 on s5p-jpeg.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move function definitions from jpeg-hw.h to jpeg-hw-s5p.c,
add "s5p" prefix and put function declarations in the jpeg-hw-s5p.h.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
You shouldn't use buffers allocated on the stack for USB transfers,
always kmalloc them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
