This patch adds basic SwitchDev driver framework for lan966x. It
includes only the IO range mapping and probing of the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses macro IANA_VXLAN_GPE_UDP_PORT to replace number 4790 for
cleanup.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta controller is able to do some tocken-bucket per-queue traffic
shaping. This commit adds support for setting these using the TC mqprio
interface.
The token-bucket parameters are customisable, but the current
implementation configures them to have a 10kbps resolution for the
rate limitation, since it allows to cover the whole range of max_rate
values from 10kbps to 5Gbps with 10kbps increments.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mqprio implementation assumed that we are only using one
queue per TC. Use the offset and count parameters to allow using
multiple queues per TC. In that case, the controller will use a standard
round-robin algorithm to pick queues assigned to the same TC, with the
same priority.
This only applies to VLAN priorities in ingress traffic, each TC
corresponding to a vlan priority.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qopt->hw flag is set by the TC code according to the offloading mode
asked by user. Don't force-set it in the driver, but instead read it to
make sure we do what's asked.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct tc_mqprio_qopt_offload is a container for struct tc_mqprio_qopt,
that allows passing extra parameters, such as traffic shaping. This commit
converts the current mqprio code to that new struct.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.
So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.
The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
they arrive there via a trap and not via flooding
It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/
To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)
The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.
Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c
Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.
On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21
So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.
The variable 'j' may be greater than or equal to 32.
At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---
Fixes: 5fabb01207 ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC9959 switch embedded within NXP LS1028A (and that version of
Ocelot switches only) supports cut-through forwarding - meaning it can
start the process of looking up the destination ports for a packet, and
forward towards those ports, before the entire packet has been received
(as opposed to the store-and-forward mode).
The up side is having lower forwarding latency for large packets. The
down side is that frames with FCS errors are forwarded instead of being
dropped. However, erroneous frames do not result in incorrect updates of
the FDB or incorrect policer updates, since these processes are deferred
inside the switch to the end of frame. Since the switch starts the
cut-through forwarding process after all packet headers (including IP,
if any) have been processed, packets with large headers and small
payload do not see the benefit of lower forwarding latency.
There are two cases that need special attention.
The first is when a packet is multicast (or flooded) to multiple
destinations, one of which doesn't have cut-through forwarding enabled.
The switch deals with this automatically by disabling cut-through
forwarding for the frame towards all destination ports.
The second is when a packet is forwarded from a port of lower link speed
towards a port of higher link speed. This is not handled by the hardware
and needs software intervention.
Since we practically need to update the cut-through forwarding domain
from paths that aren't serialized by the rtnl_mutex (phylink
mac_link_down/mac_link_up ops), this means we need to serialize physical
link events with user space updates of bonding/bridging domains.
Enabling cut-through forwarding is done per {egress port, traffic class}.
I don't see any reason why this would be a configurable option as long
as it works without issues, and there doesn't appear to be any user
space configuration tool to toggle this on/off, so this patch enables
cut-through forwarding on all eligible ports and traffic classes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only called takes ocelot_port->bridge and passes it as the "bridge"
argument to this function, which then compares it with
ocelot_port->bridge. This is not useful.
Instead, we would like this function to return 0 if ocelot_port->bridge
is not present, which is what this patch does.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When XDP program is loaded, it is desirable that the previous TX and RX
coalesce values are not re-inited to its default value. This prevents
unnecessary re-configurig the coalesce values that were working fine
before.
Fixes: ac746c8520 ("net: stmmac: enhance XDP ZC driver level switching performance")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211124114019.3949125-1-boon.leong.ong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The node pointer is returned by of_get_child_by_name() with
refcount incremented in tsnep_mdio_init(). Calling of_node_put()
to aovid the refcount leak in tsnep_mdio_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211124084048.175456-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Populate the supported interfaces bitmap and MAC capabilities mask for
the macb driver and remove the old validate implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mpuRv-00D4rb-Lz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems only XID 609 made it to the mass market. Therefore let's
disable detection of the other RTL8125a XID's. If nobody complains
we can remove support for RTL_GIGA_MAC_VER_60 later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2cd3df01-5f8b-08dd-6def-3f31a3014bde@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c2 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3d ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Even if firmware fails to recognize the plugged-in port module type,
allow reading port module EEPROM anyway. This helps in obtaining
necessary diagnostics information for debugging and analysis.
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Link: https://lore.kernel.org/r/1637682437-31407-1-git-send-email-rahul.lakkireddy@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following warning is fixed, by removing the unused resource size:
drivers/net/ethernet/engleder/tsnep_main.c:1155:21-24:
WARNING: Suspicious code. resource_size is maybe missing with io
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20211124205225.13985-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove .owner field if calls are used which set it automatically
Eliminate the following coccicheck warning:
./drivers/net/ethernet/engleder/tsnep_main.c:1263:3-8: No need to set
.owner here. The core will do it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/1637721384-70836-2-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When tx timeout occurs, the info of dql maybe helpful, so print
these info to hns3_get_tx_timeo_queue_info().
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no way to get drop packet number of multicast and
broadcast in IGU hardware module, it is not convenient to find problem
when multicast packet or broadcast packet is dropped in IGU, so this
patch adds statistics for them in debugfs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing the whole MAC addresse may bring security risks. Therefore,
the MAC address is partially encrypted to improve security.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mbx or reset message arrives, the driver is informed
through an interrupt. This task can be processed only after
the workqueue is scheduled. In some cases, this workqueue
scheduling takes a long time. As a result, the mbx or reset
service task cannot be processed in time. So add some warning
message to improve debugging efficiency for this case.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock domain crossing error (CDC) is calculated at every fetch of Tx or Rx
timestamps. It includes a division. Especially on arm32 based systems it is
expensive. It also requires two conditionals in the hotpath.
Add a compensation value cache to struct plat_stmmacenet_data and subtract it
unconditionally in the RX/TX functions which spares the conditionals.
The value is initialized to 0 and if supported calculated in the PTP
initialization code.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211122111931.135135-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently mvpp2_xdp_setup won't allow attaching XDP program if
mtu > ETH_DATA_LEN (1500).
The mvpp2_change_mtu on the other hand checks whether
MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE.
These two checks are semantically different.
Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in
mvpp2_rx we have
xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM;
xdp.frame_sz = PAGE_SIZE;
Change the checks to check whether
mtu > MVPP2_MAX_RX_BUF_SIZE
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ndo_change_proto_down was added seemingly to enable out-of-tree
implementations. Over 2.5yrs later we still have no real users
upstream. Hardwire the generic implementation for now, we can
revert once real users materialize. (rocker is a test vehicle,
not a user.)
We need to drop the optimization on the sysfs side, because
unlike ndos priv_flags will be changed at runtime, so we'd
need READ_ONCE/WRITE_ONCE everywhere..
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-11-22
Shiraz Saleem says:
Currently E800 devices come up as RoCEv2 devices by default.
This series add supports for users to configure iWARP or RoCEv2 functionality
per PCI function. devlink parameters is used to realize this and is keyed
off similar work in [1].
[1] https://lore.kernel.org/linux-rdma/20210810132424.9129-1-parav@nvidia.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During the process of driver probing, probe function should return < 0
for failure, otherwise kernel will treat value == 0 as success.
Therefore, we should set err to -EINVAL when
adapter->registered_device_map is NULL. Otherwise kernel will assume
that driver has been successfully probed and will cause unexpected
errors.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original changes brakes MAC address assignment on older chip
versions (see bug report [0]), and it brakes random MAC assignment.
is_valid_ether_addr() requires that its argument is word-aligned.
Add the missing alignment to array mac_addr.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=215087
Fixes: 1c5d09d587 ("ethernet: r8169: use eth_hw_addr_set()")
Reported-by: Richard Herbert <rherbert@sympatico.ca>
Tested-by: Richard Herbert <rherbert@sympatico.ca>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-11-22
Maciej Fijalkowski says:
Here are the two fixes for issues around ethtool's set_channels()
callback for ice driver. Both are related to XDP resources. First one
corrects the size of vsi->txq_map that is used to track the usage of Tx
resources and the second one prevents the wrong refcounting of bpf_prog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing port up/down events generated by the device's firmware,
the driver protects itself from events reported for non-existent local
ports, but not the CPU port (local port 0), which exists, but lacks a
netdev.
This can result in a NULL pointer dereference when calling
netif_carrier_{on,off}().
Fix this by bailing early when processing an event reported for the CPU
port. Problem was only observed when running on top of a buggy emulator.
Fixes: 28b1987ef5 ("mlxsw: spectrum: Register CPU port with devlink")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver fails to load with old firmware versions that cannot report
the maximum number of RIF MAC profiles [1].
Fix this by defaulting to a maximum of a single profile in such
situations, as multiple profiles are not supported by old firmware
versions.
[1]
mlxsw_spectrum 0000:03:00.0: cannot register bus device
mlxsw_spectrum: probe of 0000:03:00.0 failed with error -5
Fixes: 1c375ffb2e ("mlxsw: spectrum_router: Expose RIF MAC profiles to devlink resource")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reported-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
[1]
BUG: Bad page state in process devlink pfn:22f73d
page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x2ffff00000000000()
raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
Modules linked in:
CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44
Hardware name: Marvell Armada 7040 TX4810M (DT)
Call trace:
dump_backtrace+0x0/0x1d0
show_stack+0x1c/0x28
dump_stack+0xbc/0x118
bad_page+0xcc/0xf8
check_free_page_bad+0x80/0x88
__free_pages_ok+0x3f8/0x418
__free_pages+0x38/0x60
kmem_freepages+0x200/0x2a8
slab_destroy+0x28/0x68
slabs_destroy+0x60/0x90
___cache_free+0x1b4/0x358
kfree+0xc0/0x1d0
skb_free_head+0x2c/0x38
skb_release_data+0x110/0x1a0
skb_release_all+0x2c/0x38
consume_skb+0x38/0x130
__dev_kfree_skb_any+0x44/0x50
mlxsw_pci_rdq_fini+0x8c/0xb0
mlxsw_pci_queue_fini.isra.0+0x28/0x58
mlxsw_pci_queue_group_fini+0x58/0x88
mlxsw_pci_aqs_fini+0x2c/0x60
mlxsw_pci_fini+0x34/0x50
mlxsw_core_bus_device_unregister+0x104/0x1d0
mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48
devlink_reload+0x44/0x158
devlink_nl_cmd_reload+0x270/0x290
genl_rcv_msg+0x188/0x2f0
netlink_rcv_skb+0x5c/0x118
genl_rcv+0x3c/0x50
netlink_unicast+0x1bc/0x278
netlink_sendmsg+0x194/0x390
__sys_sendto+0xe0/0x158
__arm64_sys_sendto+0x2c/0x38
el0_svc_common.constprop.0+0x70/0x168
do_el0_svc+0x28/0x88
el0_sync_handler+0x88/0x190
el0_sync+0x140/0x180
[2]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html
[3]
https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function idr_for_each_entry() already checks that the next entry in
the IDR is not NULL.
Therefore, checking that again in every iteration leads to deadcode.
Remove the unnecessary check in order to avoid that.
Addresses-Coverity: ("Logically dead code")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow support for 'enable_iwarp' and 'enable_roce' devlink params to turn
on/off iWARP or RoCE protocol support for E800 devices.
For example, a user can turn on iWARP functionality with,
devlink dev param set pci/0000:07:00.0 name enable_iwarp value true cmode runtime
This add an iWARP auxiliary rdma device, ice.iwarp.<>, under this PF.
A user request to enable both iWARP and RoCE under the same PF is rejected
since this device does not support both protocols simultaneously on the
same port.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The change to eth_hw_addr_set() caused gcc to correctly spot a
bug that was introduced in an earlier incorrect fix:
In file included from include/linux/etherdevice.h:21,
from drivers/net/ethernet/ni/nixge.c:7:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:319:2,
inlined from 'nixge_probe' at drivers/net/ethernet/ni/nixge.c:1286:3:
include/linux/netdevice.h:4648:9: error: 'memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
As nixge_get_nvmem_address() can return either NULL or an error
pointer, the NULL check is wrong, and we can end up reading from
ERR_PTR(-EOPNOTSUPP), which gcc knows to contain zero readable
bytes.
Make the function always return an error pointer again but fix
the check to match that.
Fixes: f3956ebb3b ("ethernet: use eth_hw_addr_set() instead of ether_addr_copy()")
Fixes: abcd3d6fc6 ("net: nixge: Fix error path for obtaining mac address")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function axspi_read_status calls:
ret = spi_write_then_read(ax_spi->spi, ax_spi->cmd_buf, 1,
(u8 *)&status, 3);
status is a pointer to a struct spi_status, which is 3-byte wide:
struct spi_status {
u16 isr;
u8 status;
};
But &status is the pointer to this pointer, and spi_write_then_read does
not dereference this parameter:
int spi_write_then_read(struct spi_device *spi,
const void *txbuf, unsigned n_tx,
void *rxbuf, unsigned n_rx)
Therefore axspi_read_status currently receive a SPI response in the
pointer status, which overwrites 24 bits of the pointer.
Thankfully, on Little-Endian systems, the pointer is only used in
le16_to_cpus(&status->isr);
... which is a no-operation. So there, the overwritten pointer is not
dereferenced. Nevertheless on Big-Endian systems, this can lead to
dereferencing pointers after their 24 most significant bits were
overwritten. And in all systems this leads to possible use of
uninitialized value in functions calling spi_write_then_read which
expect status to be initialized when the function returns.
Moreover function axspi_read_status (and macro AX_READ_STATUS) do not
seem to be used anywhere. So currently this seems to be dead code. Fix
the issue anyway so that future code works properly when using function
axspi_read_status.
Fixes: a97c69ba4f ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
