xhci driver displays the supported xHC USB revision in a message during
driver load:
"Host supports USB 3.1 Enhanced SuperSpeed"
Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts
Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.
xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.
This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e2654 ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make the local ep_state variable a pointer to the actual ring ep_state.
This allows us to read fresh ep_state values every time, will be useful
later.
Also move the streams check out from bulk only case. Even if only
bulk tranfers can use streams we shouldn't continue if those flags
are set. Main reason for this change is really code readability and
grouping functionality
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function xhci_stop, xhci_debugfs_exit called before xhci_mem_cleanup.
xhci_debugfs_exit removed the xhci debugfs root nodes, xhci_mem_cleanup
called function xhci_free_virt_devices_depth_first which in turn called
function xhci_debugfs_remove_slot.
Function xhci_debugfs_remove_slot removed the nodes for devices, the nodes
folders are sub folder of xhci debugfs.
It is unreasonable to remove xhci debugfs root folder before
xhci debugfs sub folder. Function xhci_mem_cleanup should be called
before function xhci_debugfs_exit.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug after plugged out USB device, the device and its ep00
nodes are still kept, we need to remove the nodes in xhci_free_dev when
USB device is plugged out.
Fixes: 052f71e25a ("xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During system resume from hibernation, xhci host is reset, all the
nodes in devices folder are removed in xhci_mem_cleanup function.
Later nodes in /sys/kernel/debug/usb/xhci/* are created again in
function xhci_run, but the nodes already exist, so the nodes still
keep the old ones, finally device nodes in xhci debugfs folder
/sys/kernel/debug/usb/xhci/*/devices/* are disappeared.
This fix removed xhci debugfs nodes before the nodes are re-created,
so all the nodes in xhci debugfs can be re-created successfully.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the virt_device and its debugfs_private member together.
When resuming from hibernate the .free_dev callback unconditionally
freed the debugfs_private member, but could leave virt_device intact.
This triggered a NULL pointer dereference after resume when usbmuxd
sent a USBDEVFS_SETCONFIGURATION ioctl to a device, trying to add a
endpoint debugfs entry to a already freed debugfs_private pointer.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Reported-by: Alexander Kappner <agk@godking.net>
Tested-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI driver currently has the IMOD set to 160, which
translates to an IMOD interval of 40,000ns (160 * 250)ns
Commit 0cbd4b34cd ("xhci: mediatek: support MTK xHCI host controller")
introduced a QUIRK for the MTK platform to adjust this interval to 20,
which translates to an IMOD interval of 5,000ns (20 * 250)ns. This is
due to the fact that the MTK controller IMOD interval is 8 times
as much as defined in xHCI spec.
Instead of adding more quirk bits for additional platforms, this patch
introduces the ability for vendors to set the IMOD_INTERVAL as is
optimal for their platform. By using device_property_read_u32() on
"imod-interval-ns", the IMOD INTERVAL can be specified in nano seconds.
If no interval is specified, the default of 40,000ns (IMOD=160) will be
used.
No bounds checking has been implemented due to the fact that a vendor
may have violated the spec and would need to specify a value outside of
the max 8,000 IRQs/second limit specified in the xHCI spec.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each event segment has been exposed through debugfs. There is no
need to dump ERST content with printk in code. Remove it to make
code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The content of each register has been exposed through debugfs.
There is no need to dump register content with printk in code
lines. Remove them to make code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI compatible USB host controllers(i.e. super-speed USB3 controllers)
can be implemented with the Debug Capability(DbC). It presents a debug
device which is fully compliant with the USB framework and provides the
equivalent of a very high performance full-duplex serial link. The debug
capability operation model and registers interface are defined in 7.6.8
of the xHCI specification, revision 1.1.
The DbC debug device shares a root port with the xHCI host. By default,
the debug capability is disabled and the root port is assigned to xHCI.
When the DbC is enabled, the root port will be assigned to the DbC debug
device, and the xHCI sees nothing on this port. This implementation uses
a sysfs node named <dbc> under the xHCI device to manage the enabling
and disabling of the debug capability.
When the debug capability is enabled, it will present a debug device
through the debug port. This debug device is fully compliant with the
USB3 framework, and it can be enumerated by a debug host on the other
end of the USB link. As soon as the debug device is configured, a TTY
serial device named /dev/ttyDBC0 will be created.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commands with input contexts are allocated with the
xhci_alloc_command_with_ctx helper.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a xhci_alloc_command_with_ctx() helper to get rid of
one of the boolean parameters telling if a context should
be allocated with the command.
No functional changes, improves core readability
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning: variable 'ep' set but not used
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning about variable 'last_freed_endpoint'
set but not used [-Wunused-but-set-variable]
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci driver handles USB transaction errors on transfer events,
but transaction errors are possible on address device command
completion events as well.
The xHCI specification (section 4.6.5) says: A USB Transaction
Error Completion Code for an Address Device Command may be due
to a Stall response from a device. Software should issue a Disable
Slot Command for the Device Slot then an Enable Slot Command to
recover from this error.
This patch handles USB transaction errors on address command
completion events. The related discussion threads can be found
through below links.
http://marc.info/?l=linux-usb&m=149362010728921&w=2http://marc.info/?l=linux-usb&m=149252752825755&w=2
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci->mutex was added in xhci_alloc_dev() to protect two race sources
(xhci->slot_id and xhci->addr_dev) by commit a00918d052 ("usb: host:
xhci: add mutex for non-thread-safe data").
While xhci->slot_id has been discarded in commit c2d3d49bba ("usb:
xhci: move slot_id from xhci_hcd to xhci_command structure"), and
xhci->addr_dev has been removed in commit 87e44f2aac ("usb: xhci:
remove the use of xhci->addr_dev"), it's now safe to remove the use of
xhci->mutex in xhci_alloc_dev().
Link: https://marc.info/?l=linux-usb&m=150306294725821&w=2
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it returns
success when it sees a dead host. This is not the right way to go.
It should return error and let the invoker know that disable slot
command was failed due to a dead host.
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci_disable_slot() returns success, a disable slot command
trb was queued in the command ring. The command completion
handler will free the virtual device data structure associated
with the slot. On the other hand, when xhci_disable_slot()
returns error, the invokers should take the responsibilities to
free the slot related data structure. Otherwise, memory leakage
happens.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds debugfs consumer for xHCI driver. The debugfs entries
read all host registers, device/endpoint contexts, command ring,
event ring and various endpoint rings. With these entries, users
can check the registers and memory spaces used by a host during
run time, or save all the information with a simple 'cp -r' for
post-mortem programs.
The file hierarchy looks like this.
[root of debugfs]
|__usb
|____[e,u,o]hci <---------[root for other HCIs]
|____xhci <---------------[root for xHCI]
|______0000:00:14.0 <--------------[xHCI host name]
|________reg-cap <--------[capability registers]
|________reg-op <-------[operational registers]
|________reg-runtime <-----------[runtime registers]
|________reg-ext-#cap_name <----[extended capability regs]
|________command-ring <-------[root for command ring]
|__________cycle <------------------[ring cycle]
|__________dequeue <--------[ring dequeue pointer]
|__________enqueue <--------[ring enqueue pointer]
|__________trbs <-------------------[ring trbs]
|________event-ring <---------[root for event ring]
|__________cycle <------------------[ring cycle]
|__________dequeue <--------[ring dequeue pointer]
|__________enqueue <--------[ring enqueue pointer]
|__________trbs <-------------------[ring trbs]
|________devices <------------[root for devices]
|__________#slot_id <-----------[root for a device]
|____________name <-----------------[device name]
|____________slot-context <----------------[slot context]
|____________ep-context <-----------[endpoint contexts]
|____________ep#ep_index <--------[root for an endpoint]
|______________cycle <------------------[ring cycle]
|______________dequeue <--------[ring dequeue pointer]
|______________enqueue <--------[ring enqueue pointer]
|______________trbs <-------------------[ring trbs]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI specification 1.1 does not require xHCI-compliant controllers
to always enable hardware USB2 LPM. However, the current xHCI
driver always enable it when seeing HLC=1.
This patch supports an option for users to control disabling
USB2 Hardware LPM via DT/ACPI attribute.
This option is needed in case user would like to disable this
feature. For example, their xHCI controller has its USB2 HW LPM
broken.
Signed-off-by: Tung Nguyen <tunguyen@apm.com>
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the xhci_add_endpoint(), a new ring was allocated and saved at
xhci_virt_ep->new_ring. Hence, when error happens, we need to free
the allocated ring before returning error.
Current code frees xhci_virt_ep->ring instead of the new_ring. This
patch fixes this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of stopped_stream member in virtual endpoint structure as
it is only used in one case when cleaning a halted endpoint.
Pass it as function parameter instead.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anurag Kumar Vulisha reported several issues with xhci endpoint
ring caching.
31 Rings are cached per device before a ring is freed.
These cached rings are not used as default if a new ring is needed.
They are only used if the driver fails to allocate memory for a ring.
The current ring cache is more a reason to why we run out memory than a
help when we actually do so.
Anurag Kumar Vulisha tried to use cached rings as a first option and
found new issues with cached ring initialization.
Cached rings were first zeroed and then manually reinitialized with link
trbs etc, but forgetting to set some important bits like cycle toggle bit.
Remove the ring cache completely as it's a faulty premature optimization
eating memory
Reported-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The values for the new dequeue segment, new dequeue pointer and new cycle
state are needed for manually moving the xHC ring dequeue pointer.
These are conveniently stored in a xhci_dequeue_state structure.
stream support was added later and stream_id was carried
as a function parameter.
Move the stream_id to the xhci_dequeue_state structure instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4.11 TRB completion codes were renamed to match spec.
Completion codes for command ring stopped and endpoint stopped
were mixed, leading to failures while handling a stopped command ring.
Use the correct completion code for command ring stopped events.
Fixes: 0b7c105a04 ("usb: host: xhci: rename completion codes to match spec")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram
If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
then the assertion of the Interrupt Pending (IP) flag in Figure 30
generates a PCI Dword write. The IP flag is automatically cleared
by the completion of the PCI write.
the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the modern API to request MSI or MSI-X interrupts, which allows us to
get rid of the msix_entries array, as well as cleaning up the cleanup
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI context changes have already been traced by the trace
events. It's unnecessary to put the same message in kernel
log. This patch removes the use of xhci_dbg_ctx().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI ring changes have already been traced by the ring trace
events. It's unnecessary to put the same messages in kernel
log. This patch removes the debugging code for a ring.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several functions have a single user in the same file where it
is defined. There's no need to expose it anywhere else.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new xhci_hc_died() function that takes care of handling
pending commands and URBs if a host controller becomes unresponsive.
This addresses issues on hotpluggable xhci controllers that disappear
from the bus suddenly, often while the bus (PCI) remove function is
still being processed.
xhci_hc_died() sets a XHCI_STATUS_DYING flag to prevent new URBs and
commands or to be queued. The flag also ensures xhci_hc_died() will
give back pending commands and URBs once.
Host is considered dead if register read returns 0xffffffff, or host
fails to abort the command ring, or fails stopping an endpoint after
trying for 5 seconds.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't halt the host controller immediately when first HCD is removed as
it will cause problems if we have devices attached to the second (primary)
HCD, like a keyboard.
We've been carrying this in our Linux-as-a-bootloader environment for a
little while now. The machines all have the same TI TUSB73x0 part,
and when we kexec the devices don't come back until a system power cycle.
[minor adjustments, code comments and remove HALT check -Mathias]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With these, we can track what's happening with the HW while executing
each and every command. It will give us visibility into how the
different contexts are being modified by xHC which can bring insight
into problems while debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the visability of xhci_start() so that it
can be used when enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring slot disable related code into a helper
function xhci_disable_slot() which can be used when
enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EINT(Event Interrupt) is a write-1-to-clear type of bit in xhci
status register. It should be cleared by writing a 1. Writing 0
to this bit has no effect.
Xhci driver tries to clear this bit by writing 0 to it. This is
not the right way to go. This patch corrects this by reading the
register first, then clearing all RO/RW1C/RsvZ bits and setting
the clearing bit, and writing back the new value at last.
Xhci spec requires that software that uses EINT shall clear it
prior to clearing any IP flags in section 5.4.2. This is the
reason why this patch is CC'ed stable as well.
[old way didn't cause any issues, skip stable, send to next -Mathias]
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci needs to take care of four scenarios when asked to cancel a URB.
1 URB is not queued or already given back.
usb_hcd_check_unlink_urb() will return an error, we pass the error on
2 We fail to find xhci internal structures from urb private data such as
virtual device and endpoint ring.
Give back URB immediately, can't do anything about internal structures.
3 URB private data has valid pointers to xhci internal data, but host is
not responding.
give back URB immedately and remove the URB from the endpoint lists.
4 Everyting is working
add URB to cancel list, queue a command to stop the endpoint, after
which the URB can be turned to no-op or skipped, removed from lists,
and given back.
We failed to give back the urb in case 2 where the correct device and
endpoint pointers could not be retrieved from URB private data.
This caused a hang on Dell Inspiron 5558/0VNM2T at resume from suspend
as urb was never returned.
[ 245.270505] INFO: task rtsx_usb_ms_1:254 blocked for more than 120 seconds.
[ 245.272244] Tainted: G W 4.11.0-rc3-ARCH #2
[ 245.273983] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 245.275737] rtsx_usb_ms_1 D 0 254 2 0x00000000
[ 245.277524] Call Trace:
[ 245.279278] __schedule+0x2d3/0x8a0
[ 245.281077] schedule+0x3d/0x90
[ 245.281961] usb_kill_urb.part.3+0x6c/0xa0 [usbcore]
[ 245.282861] ? wake_atomic_t_function+0x60/0x60
[ 245.283760] usb_kill_urb+0x21/0x30 [usbcore]
[ 245.284649] usb_start_wait_urb+0xe5/0x170 [usbcore]
[ 245.285541] ? try_to_del_timer_sync+0x53/0x80
[ 245.286434] usb_bulk_msg+0xbd/0x160 [usbcore]
[ 245.287326] rtsx_usb_send_cmd+0x63/0x90 [rtsx_usb]
Reported-by: diego.viola@gmail.com
Tested-by: diego.viola@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For xhci-hcd platform device, all the DMA parameters are not
configured properly, notably dma ops for dwc3 devices. So, set
the dma for xhci from sysdev. sysdev is pointing to device that
is known to the system firmware or hardware.
Cc: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.
when say N here it will not build PCI related code in USB driver.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use switch instead of several if statements
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of storing a zero length array of td pointers, and then
allocate memory both for the td pointer array and the td's, just
use a zero length array of actual td's in urb private data.
old:
struct urb_priv {
struct xhci_td *td[0]
}
new:
struct urb_priv {
struct xhci_td td[0]
}
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb_priv structure has a count on how many TDs the
URB contains, and how many of those TD's we have handled.
rename:
length -> num_tds
td_cnt -> num_tds_done
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functinal changes.
num_tds describes the number of transfer descriptor better than "size"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's start tracing at least part of an xhci_virt_device lifetime. We
might want to extend this tracepoint class later, but for now it already
exposes quite a bit of valuable information.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These three new tracers will help us tie TRBs into URBs by *also*
looking into URB lifetime.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup only. This patch is a mechaninal rename to make sure our macros
for TRB completion codes match what the specification uses to refer to
such errors. The idea behind this is that it makes it far easier to grep
the specification and match it with implementation.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a cleanup patch only, no functional changes. The idea is just to
make sure for loops look the same all over the driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A counter was used to find out if the stop endpoint completion raced with
the stop endpoint timeout timer. This was needed in case the stop ep
completion failed to delete the timer as it was running on anoter cpu.
The EP_STOP_CMD_PENDING flag was not enough as a new stop endpoint command
may be queued between the command completion and timeout function, which
would set the flag back.
Instead of the separate counter that was used we can detect the race by
checking both the STOP_EP_PENDING flag and timer_pending in the timeout
function.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want to confuse halted and stalled endpoint states with
a flag indicating we are waiting for a stop endpoint command to
finish or timeout
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.
xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.
Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.
Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.
This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_setup_device() should return failure with correct error number
when xhci host has died, removed or halted.
During usb device enumeration, if usb host is not accessible (died,
removed or halted), the hc_driver->address_device() should return
a corresponding error code to usb core. But current xhci driver just
returns success. This misleads usb core to continue the enumeration
by reading the device descriptor, which will result in failure, and
users will get a misleading message like "device descriptor read/8,
error -110".
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
xhci->slot_id is used for providing a way to pass slot id from the
command completion handler to the function waiting for completion.
It's shared by enumerations of all USB devices connected to an
xhci host. Hence, it's a source for possible races. Since we've
introduced command structure and the command queue to xhci driver.
It's better to move slot_id from xhci_hcd structure to xhci_command
structure. Hence the race source is removed.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci->addr_dev is used for the completion of both address device
and enable slot commands. It's shared by enumerations of all USB
devices connected to an xhci host. Hence, it's just a source for
possible races. Since we've introduced command structure and the
command queue to xhci driver. It is time to get rid of addr_dev
and use the completion in the command structure instead.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
define GET_EP_CTX_STATE() macro to get the endpoint state from a
pointer to a le32 enpoint context structure
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in trying to reset the host controller by writing
to its registers if host is removed and registers just return 0xffffffff
bail out and return -ENODEV instead
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old error message always stated that host was not halted
even after trying a certain time.
Host may fail the halt immediately as well with -ENODEV if device
is removed and returns 0xffffffff.
Use a more generic error message and show return value to know if we
failed with -ETIMEDOUT or -ENODEV
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_endpoint_maxp() is now returning maxpacket
correctly - iow only bits 10:0. We can finaly remove
XHCI's private GET_MAX_PACKET macro.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the last trb before a link is not packet size aligned, and is not
splittable then use a bounce buffer for that chunk of max packet size
unalignable data.
Allocate a max packet size bounce buffer for every segment of a bulk
endpoint ring at the same time as allocating the ring.
If we need to align the data before the link trb in that segment then
copy the data to the segment bounce buffer, dma map it, and enqueue it.
Once the td finishes, or is cancelled, unmap it.
For in transfers we need to first map the bounce buffer, then queue it,
after it finishes, copy the bounce buffer to the original sg list, and
finally unmap it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1c127ae99 ("usb: host: xhci: plat: make use of new methods in
xhci_plat_priv") sets xhci->quirks before calling xhci_gen_setup(), which
will overwrite them.
Don't overwite the quirks, just add the new ones
Fixes: b1c127ae99 ("usb: host: xhci: plat: make use of new methods in xhci_plat_priv")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b0 ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Cc: stable@vger.kernel.org
Reviewed-by: Roger Quadros <rogerq@ti.com>
Cc: <stable@vger.kernel.org> #v4.3+
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicate function xhci_urb_to_transfer_ring from xhci.c.
We have same function in xhci-ring.c.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.
So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Cc: <stable@vger.kernel.org>
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.
When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module should fail to load.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reseved
DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
8 times as much as that defined in xHCI spec.
3. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleanups the hcd private size to suitable size.
The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver
as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides
or xhci_pci_overrides as extra_priv_size. However, the xhci driver
uses a "sizeof(struct xhcd_hcd)" memory space in each hcd
(main_hcd and shared_hcd) actually.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change avoids DMA error in the cases where dma_mask and
coherent_dma_mask of a 32-bit controller get configured as
DMA_BIT_MASK(64) when running on a 64-bit system.
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1
For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in
pci config space. Platform controllers will need to set xhci->sbrn == 0x31
to indicate USB 3.1 support before calling xhci_gen_setup().
Also make sure xhci driver works correctly with speed set to HCD_USB31
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci 1.1 capable controllers have a new HCCPARAMS2 registers
with bits indicating support for new xhci 1.1 capabilities.
Also add support for the new xhci 1.1 bits in the config operational
opertational register that used to be reserved
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
[modified and left out parts not related to HCCPARAMS2 -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
