When we return pages to the system, we ensure that they are marked as
being in the CPU domain since any external access is uncontrolled and we
must assume the worst. This means that we need to always flush the pages
on acquisition if we need to use them on the GPU, and from the beginning
have used set-domain. Set-domain is overkill for the purpose as it is a
general synchronisation barrier, but our intent is to only flush the
pages being swapped in. If we move that flush into the pages acquisition
phase, we know then that when we have obj->mm.pages, they are coherent
with the GPU and need only maintain that status without resorting to
heavy handed use of set-domain.
The principle knock-on effect for userspace is through mmap-gtt
pagefaulting. Our uAPI has always implied that the GTT mmap was async
(especially as when any pagefault occurs is unpredicatable to userspace)
and so userspace had to apply explicit domain control itself
(set-domain). However, swapping is transparent to the kernel, and so on
first fault we need to acquire the pages and make them coherent for
access through the GTT. Our use of set-domain here leaks into the uABI
that the first pagefault was synchronous. This is unintentional and
baring a few igt should be unoticed, nevertheless we bump the uABI
version for mmap-gtt to reflect the change in behaviour.
Another implication of the change is that gem_create() is presumed to
create an object that is coherent with the CPU and is in the CPU write
domain, so a set-domain(CPU) following a gem_create() would be a minor
operation that merely checked whether we could allocate all pages for
the object. On applying this change, a set-domain(CPU) causes a clflush
as we acquire the pages. This will have a small impact on mesa as we move
the clflush here on !llc from execbuf time to create, but that should
have minimal performance impact as the same clflush exists but is now
done early and because of the clflush issue, userspace recycles bo and
so should resist allocating fresh objects.
Internally, the presumption that objects are created in the CPU
write-domain and remain so through writes to obj->mm.mapping is more
prevalent than I expected; but easy enough to catch and apply a manual
flush.
For the future, we should push the page flush from the central
set_pages() into the callers so that we can more finely control when it
is applied, but for now doing it one location is easier to validate, at
the cost of sometimes flushing when there is no need.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321161908.8007-1-chris@chris-wilson.co.uk
The timeline->name is only used for convenience in pretty printing the
i915_request.fence->ops->get_timeline_name() and it is just as
convenient to pull it from the gem_context directly. The few instances
of its use inside GEM_TRACE() has proven more of a nuisance than
helpful, so not worth saving imo.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321140711.11190-4-chris@chris-wilson.co.uk
Now that the internal code all works on intel_uncore, flip the
external-facing interface.
v2: fix GVT.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319183543.13679-4-daniele.ceraolospurio@intel.com
Each engine acquires a pin on the kernel contexts (normal and preempt)
so that the logical state is always available on demand. Keep track of
each engines pin by storing the returned pointer on the engine for quick
access.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190308132522.21573-6-chris@chris-wilson.co.uk
In preparation for an ever growing number of engines and so ever
increasing static array of HW contexts within the GEM context, move the
array over to an rbtree, allocated upon first use.
Unfortunately, this imposes an rbtree lookup at a few frequent callsites,
but we should be able to mitigate those by moving over to using the HW
context as our primary type and so only incur the lookup on the boundary
with the user GEM context and engines.
v2: Check for no HW context in guc_stage_desc_init
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190308132522.21573-4-chris@chris-wilson.co.uk
We can no longer assume execution ordering, and in particular we cannot
assume which context will execute last. One side-effect of this is that
we cannot determine if the kernel-context is resident on the GPU, so
remove the routines that claimed to do so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190308093657.8640-4-chris@chris-wilson.co.uk
Currently we assume that we know the order in which requests run and so
can determine if we need to reissue a switch-to-kernel-context prior to
idling. That assumption does not hold for the future, so instead of
tracking which barriers have been used, simply determine if we have ever
switched away from the kernel context by using the engine and before
idling ensure that all engines that have been used since the last idle
are synchronously switched back to the kernel context for safety (and
else of shrinking memory while idle).
v2: Use intel_engine_mask_t and ALL_ENGINES
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190308093657.8640-3-chris@chris-wilson.co.uk
To find the active request, we need only search along the individual
engine for the right request. This does not require touching any global
GEM state, so move it into the engine compartment.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190305180332.30900-3-chris@chris-wilson.co.uk
In the next patch, we are introducing a broad virtual engine to encompass
multiple physical engines, losing the 1:1 nature of BIT(engine->id). To
reflect the broader set of engines implied by the virtual instance, lets
store the full bitmask.
v2: Use intel_engine_mask_t (s/ring_mask/engine_mask/)
v3: Tvrtko voted for moah churn so teach everyone to not mention ring
and use $class$instance throughout.
v4: Comment upon the disparity in bspec for using VCS1,VCS2 in gen8 and
VCS[0-4] in later gen. We opt to keep the code consistent and use
0-index naming throughout.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190305180332.30900-1-chris@chris-wilson.co.uk
As we allow per-context engine allows the legacy concept of
I915_EXEC_RING no longer applies universally. We are still exposing the
unrelated exec-id in GEM_BUSY, so transition this ioctl (once more
slightly changing its ABI, but no one cares) over to only reporting the
uabi-class (not instance as we can not foreseeably fit those into the
small bitmask).
The only user of the extended ring information from GEM_BUSY is ddx/sna,
which tries to use the non-rcs business information to guide which
engine to use for subsequent operations on foreign bo. All that matters
for it is the decision between rcs and !rcs, so it is unaffected by the
change in higher bits.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190305162643.20243-1-chris@chris-wilson.co.uk
Having introduced per-context seqno, we now have a means to identity
progress across the system without feel of rollback as befell the
global_seqno. That is we can program a MI_SEMAPHORE_WAIT operation in
advance of submission safe in the knowledge that our target seqno and
address is stable.
However, since we are telling the GPU to busy-spin on the target address
until it matches the signaling seqno, we only want to do so when we are
sure that busy-spin will be completed quickly. To achieve this we only
submit the request to HW once the signaler is itself executing (modulo
preemption causing us to wait longer), and we only do so for default and
above priority requests (so that idle priority tasks never themselves
hog the GPU waiting for others).
As might be reasonably expected, HW semaphores excel in inter-engine
synchronisation microbenchmarks (where the 3x reduced latency / increased
throughput more than offset the power cost of spinning on a second ring)
and have significant improvement (can be up to ~10%, most see no change)
for single clients that utilize multiple engines (typically media players
and transcoders), without regressing multiple clients that can saturate
the system or changing the power envelope dramatically.
v3: Drop the older NEQ branch, now we pin the signaler's HWSP anyway.
v4: Tell the world and include it as part of scheduler caps.
Testcase: igt/gem_exec_whisper
Testcase: igt/benchmarks/gem_wsim
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190301170901.8340-3-chris@chris-wilson.co.uk
If we have parked, then we must have passed an idleness test and still
be idle. We chose not to use this shortcut in the past so that we could
use the idleness test at any time and inspect HW. However, some HW like
Sandybridge, doesn't like being woken up frivolously, so avoid doing so.
References: 0b702dca26 ("drm/i915: Avoid waking the engines just to check if they are idle")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190227214159.7946-1-chris@chris-wilson.co.uk
This reverts commit 0b702dca26.
CI reports that this is not as reliable as it first appears, with
failures starting to sporadically occur in selftests.
Fixes: 0b702dca26 ("drm/i915: Avoid waking the engines just to check if they are idle")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190227204654.14907-1-chris@chris-wilson.co.uk
Having weaned the interrupt handling off using a single global execution
queue, we no longer need to emit a global_seqno. Note that we still have
a few assumptions about execution order along engine timelines, but this
removes the most obvious artefact!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226094922.31617-3-chris@chris-wilson.co.uk
To determine whether an engine has 'stuck', we simply check whether or
not is still on the same seqno for several seconds. To keep this simple
mechanism intact over the loss of a global seqno, we can simply add a
new global heartbeat seqno instead. As we cannot know the sequence in
which requests will then be completed, we use a primitive random number
generator instead (with a cycle long enough to not matter over an
interval of a few thousand requests between hangcheck samples).
The alternative to using a dedicated seqno on every request is to issue
a heartbeat request and query its progress through the system. Sadly
this requires us to reduce struct_mutex so that we can issue requests
without requiring that bkl.
v2: And without the extra CS_STALL for the hangcheck seqno -- we don't
need strict serialisation with what comes later, we just need to be sure
we don't write the hangcheck seqno before our batch is flushed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190226094922.31617-1-chris@chris-wilson.co.uk
At a few points in our uABI, we check to see if the driver is wedged and
report -EIO back to the user in that case. However, as we perform the
check and reset asynchronously (where once before they were both
serialised by the struct_mutex), we may instead see the temporary wedging
used to cancel inflight rendering to avoid a deadlock during reset
(caused by either us timing out in our reset handler,
i915_wedge_on_timeout or with malice aforethought in intel_reset_prepare
for a stuck modeset). If we suspect this is the case, that is we see a
wedged driver *and* reset in progress, then wait until the reset is
resolved before reporting upon the wedged status.
v2: might_sleep() (Mika)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109580
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220145637.23503-1-chris@chris-wilson.co.uk
While this is mainly only useful for ELSP[0], it is definitely useful to
know the current timeline seqno wrt to the queued set of requests for
that port, as this carries additional information above and beyond the
near-defunct global_seqno and global HWSP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190211131004.11634-1-chris@chris-wilson.co.uk
Looking forward, we need to break the struct_mutex dependency on
i915_gem_active. In the meantime, external use of i915_gem_active is
quite beguiling, little do new users suspect that it implies a barrier
as each request it tracks must be ordered wrt the previous one. As one
of many, it can be used to track activity across multiple timelines, a
shared fence, which fits our unordered request submission much better. We
need to steer external users away from the singular, exclusive fence
imposed by i915_gem_active to i915_active instead. As part of that
process, we move i915_gem_active out of i915_request.c into
i915_active.c to start separating the two concepts, and rename it to
i915_active_request (both to tie it to the concept of tracking just one
request, and to give it a longer, less appealing name).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205130005.2807-5-chris@chris-wilson.co.uk
A few years ago, see commit 688e6c7258 ("drm/i915: Slaughter the
thundering i915_wait_request herd"), the issue of handling multiple
clients waiting in parallel was brought to our attention. The
requirement was that every client should be woken immediately upon its
request being signaled, without incurring any cpu overhead.
To handle certain fragility of our hw meant that we could not do a
simple check inside the irq handler (some generations required almost
unbounded delays before we could be sure of seqno coherency) and so
request completion checking required delegation.
Before commit 688e6c7258, the solution was simple. Every client
waiting on a request would be woken on every interrupt and each would do
a heavyweight check to see if their request was complete. Commit
688e6c7258 introduced an rbtree so that only the earliest waiter on
the global timeline would woken, and would wake the next and so on.
(Along with various complications to handle requests being reordered
along the global timeline, and also a requirement for kthread to provide
a delegate for fence signaling that had no process context.)
The global rbtree depends on knowing the execution timeline (and global
seqno). Without knowing that order, we must instead check all contexts
queued to the HW to see which may have advanced. We trim that list by
only checking queued contexts that are being waited on, but still we
keep a list of all active contexts and their active signalers that we
inspect from inside the irq handler. By moving the waiters onto the fence
signal list, we can combine the client wakeup with the dma_fence
signaling (a dramatic reduction in complexity, but does require the HW
being coherent, the seqno must be visible from the cpu before the
interrupt is raised - we keep a timer backup just in case).
Having previously fixed all the issues with irq-seqno serialisation (by
inserting delays onto the GPU after each request instead of random delays
on the CPU after each interrupt), we can rely on the seqno state to
perfom direct wakeups from the interrupt handler. This allows us to
preserve our single context switch behaviour of the current routine,
with the only downside that we lose the RT priority sorting of wakeups.
In general, direct wakeup latency of multiple clients is about the same
(about 10% better in most cases) with a reduction in total CPU time spent
in the waiter (about 20-50% depending on gen). Average herd behaviour is
improved, but at the cost of not delegating wakeups on task_prio.
v2: Capture fence signaling state for error state and add comments to
warm even the most cold of hearts.
v3: Check if the request is still active before busywaiting
v4: Reduce the amount of pointer misdirection with list_for_each_safe
and using a local i915_request variable inside the loops
v5: Add a missing pluralisation to a purely informative selftest message.
References: 688e6c7258 ("drm/i915: Slaughter the thundering i915_wait_request herd")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129205230.19056-2-chris@chris-wilson.co.uk
After noticing that we trigger preemption events for currently executing
requests, as well as requests that complete before the preemption and
attempting to suppress those preemption events, it is wise to not
consider the queue_priority to be authoritative. As we only track the
maximum priority seen between dequeue passes, if the maximum priority
request is no longer available for dequeuing (it completed or is even
executing on another engine), we have no knowledge of the previous
queue_priority as it would require us to keep a full history of enqueued
requests -- but we already have that history in the priolists!
Rename the queue_priority to queue_priority_hint so that we do not
confuse it as being exactly the maximum priority in the queue, but merely
an indication that we have seen a new maximum priority value and as such
we should check whether it should preempt the currently running request.
v2: s/preempt_priority_hint/queue_priority_hint/ as preempt implies it
being only used for the singular task of preemption and not the wider
question of waking up due to a change in the queue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129185452.20989-3-chris@chris-wilson.co.uk
To allow requests to forgo a common execution timeline, one question we
need to be able to answer is "is this request running?". To track
whether a request has started on HW, we can emit a breadcrumb at the
beginning of the request and check its timeline's HWSP to see if the
breadcrumb has advanced past the start of this request. (This is in
contrast to the global timeline where we need only ask if we are on the
global timeline and if the timeline has advanced past the end of the
previous request.)
There is still confusion from a preempted request, which has already
started but relinquished the HW to a high priority request. For the
common case, this discrepancy should be negligible. However, for
identification of hung requests, knowing which one was running at the
time of the hang will be much more important.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129185452.20989-2-chris@chris-wilson.co.uk
Now that we have allocated ourselves a cacheline to store a breadcrumb,
we can emit a write from the GPU into the timeline's HWSP of the
per-context seqno as we complete each request. This drops the mirroring
of the per-engine HWSP and allows each context to operate independently.
We do not need to unwind the per-context timeline, and so requests are
always consistent with the timeline breadcrumb, greatly simplifying the
completion checks as we no longer need to be concerned about the
global_seqno changing mid check.
One complication though is that we have to be wary that the request may
outlive the HWSP and so avoid touching the potentially danging pointer
after we have retired the fence. We also have to guard our access of the
HWSP with RCU, the release of the obj->mm.pages should already be RCU-safe.
At this point, we are emitting both per-context and global seqno and
still using the single per-engine execution timeline for resolving
interrupts.
v2: s/fake_complete/mark_complete/
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128181812.22804-5-chris@chris-wilson.co.uk
Allocate a page for use as a status page by a group of timelines, as we
only need a dword of storage for each (rounded up to the cacheline for
safety) we can pack multiple timelines into the same page. Each timeline
will then be able to track its own HW seqno.
v2: Reuse the common per-engine HWSP for the solitary ringbuffer
timeline, so that we do not have to emit (using per-gen specialised
vfuncs) the breadcrumb into the distinct timeline HWSP and instead can
keep on using the common MI_STORE_DWORD_INDEX. However, to maintain the
sleight-of-hand for the global/per-context seqno switchover, we will
store both temporarily (and so use a custom offset for the shared timeline
HWSP until the switch over).
v3: Keep things simple and allocate a page for each timeline, page
sharing comes next.
v4: I was caught repeating the same MI_STORE_DWORD_IMM over and over
again in selftests.
v5: And caught red handed copying create timeline + check.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128181812.22804-3-chris@chris-wilson.co.uk
Currently we only allocate an object and vma if we are using a GGTT
virtual HWSP, and a plain struct page for a physical HWSP. For
convenience later on with global timelines, it will be useful to always
have the status page being tracked by a struct i915_vma. Make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128102356.15037-4-chris@chris-wilson.co.uk
Now that the submission backends are controlled via their own spinlocks,
with a wave of a magic wand we can lift the struct_mutex requirement
around GPU reset. That is we allow the submission frontend (userspace)
to keep on submitting while we process the GPU reset as we can suspend
the backend independently.
The major change is around the backoff/handoff strategy for performing
the reset. With no mutex deadlock, we no longer have to coordinate with
any waiter, and just perform the reset immediately.
Testcase: igt/gem_mmap_gtt/hang # regresses
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125132230.22221-3-chris@chris-wilson.co.uk
Instead of tediously and fragilely counting up the number of dwords
required to emit the breadcrumb to seal a request, fake a request and
measure it automatically once during engine setup.
The downside is that this requires a fair amount of mocking to create a
proper breadcrumb. Still, should be less error prone in future as the
breadcrumb size fluctuates!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125100520.20163-1-chris@chris-wilson.co.uk
Since commit d4ccceb055 ("drm/i915/icl: Ringbuffer interrupt handling")
we have required a mechanism to avoid touching the interrupt hardware
for breadcrumbs, superseding our mock interface for selftests.
The residual problem (ideas welcome) is in probing the mock ring
registers for ring_is_idle. Hmm, maybe we should just install
mock handlers for i915->uncore.mmio__write and friends? Only problem
being is that we would to truly mock some expected reads. :(
References: d4ccceb055 ("drm/i915/icl: Ringbuffer interrupt handling")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118112225.13780-1-chris@chris-wilson.co.uk
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Minor checkpatch fixes sprinkled on top of the changed lines.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/14ed72e7f04c9340a057855c5950b54811f8a477.1547629303.git.jani.nikula@intel.com
Keep track of the temporary rpm wakerefs used for user access to the
device, so that we can cancel them upon release and clearly identify any
leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-10-chris@chris-wilson.co.uk
The majority of runtime-pm operations are bounded and scoped within a
function; these are easy to verify that the wakeref are handled
correctly. We can employ the compiler to help us, and reduce the number
of wakerefs tracked when debugging, by passing around cookies provided
by the various rpm_get functions to their rpm_put counterpart. This
makes the pairing explicit, and given the required wakeref cookie the
compiler can verify that we pass an initialised value to the rpm_put
(quite handy for double checking error paths).
For regular builds, the compiler should be able to eliminate the unused
local variables and the program growth should be minimal. Fwiw, it came
out as a net improvement as gcc was able to refactor rpm_get and
rpm_get_if_in_use together,
v2: Just s/rpm_put/rpm_put_unchecked/ everywhere, leaving the manual
mark up for smaller more targeted patches.
v3: Mention the cookie in Returns
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-2-chris@chris-wilson.co.uk
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXDOTqAAKCRDj7w1vZxhR
xZ8QAQD4j8m9Ea3bzY5Rr8BYUx1k+Cjj6Y6abZmot2rSvdyOHwD+JzJFIFAPZjdd
uOKhLnDlubaaoa6OGPDQShjl9p3gyQE=
=WQGO
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-07-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: applied amdgpu merge fixup]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107180333.amklwycudbsub3s5@flea
When we first introduced the reset to sanitize the GPU on taking over
from the BIOS and before returning control to third parties (the BIOS!),
we restricted it to only systems utilizing HW contexts as we were
uncertain of how stable our reset mechanism truly was. We now have
reasonable coverage across all machines that expose a GPU reset method,
and so we should be safe to sanitize the GPU state everywhere.
v2: We _have_ to skip the reset if it would clobber the display.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103112104.19561-1-chris@chris-wilson.co.uk
Now that we have eliminated the CPU-side irq_seqno_barrier by moving the
delays on the GPU before emitting the MI_USER_INTERRUPT, we can remove
the engine->irq_seqno_barrier infrastructure. Though intentionally
slowing down the GPU is nasty, so is the code we can now remove!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228171641.16531-6-chris@chris-wilson.co.uk
The writing is on the wall for the existence of a single execution queue
along each engine, and as a consequence we will not be able to track
dependencies along the HW queue itself, i.e. we will not be able to use
HW semaphores on gen7 as they use a global set of registers (and unlike
gen8+ we can not effectively target memory to keep per-context seqno and
dependencies).
On the positive side, when we implement request reordering for gen7 we
also can not presume a simple execution queue and would also require
removing the current semaphore generation code. So this bring us another
step closer to request reordering for ringbuffer submission!
The negative side is that using interrupts to drive inter-engine
synchronisation is much slower (4us -> 15us to do a nop on each of the 3
engines on ivb). This is much better than it was at the time of introducing
the HW semaphores and equally important userspace weaned itself off
intermixing dependent BLT/RENDER operations (the prime culprit was glyph
rendering in UXA). So while we regress the microbenchmarks, it should not
impact the user.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108888
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228140736.32606-2-chris@chris-wilson.co.uk
Having completed a test run of gem_eio across all machines in CI we also
observe the phenomenon (of lost interrupts after resetting the GPU) on
gen3 machines as well as the previously sighted gen6/gen7. Let's apply
the same HWSTAM workaround that was effective for gen6+ for all, as
although we haven't seen the same failure on gen4/5 it seems prudent to
keep the code the same.
As a consequence we can remove the extra setting of HWSTAM and apply the
register from a single site.
v2: Delazy and move the HWSTAM into its own function
v3: Mask off all HWSP writes on driver unload and engine cleanup.
v4: And what about the physical hwsp?
v5: No, engine->init_hw() is not called from driver_init_hw(), don't be
daft. Really scrub HWSTAM as early as we can in driver_init_mmio()
v6: Rename set_hwsp as it was setting the mask not the hwsp register.
v7: Ville pointed out that although vcs(bsd) was introduced for g4x/ilk,
per-engine HWSTAM was not introduced until gen6!
References: https://bugs.freedesktop.org/show_bug.cgi?id=108735
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181218102712.11058-1-chris@chris-wilson.co.uk
Define IS_GEN() similarly to our IS_GEN_RANGE(). but use gen instead of
gen_mask to do the comparison. Now callers can pass then gen as a parameter,
so we don't require one macro for each gen.
The following spatch was used to convert the users of these macros:
@@
expression e;
@@
(
- IS_GEN2(e)
+ IS_GEN(e, 2)
|
- IS_GEN3(e)
+ IS_GEN(e, 3)
|
- IS_GEN4(e)
+ IS_GEN(e, 4)
|
- IS_GEN5(e)
+ IS_GEN(e, 5)
|
- IS_GEN6(e)
+ IS_GEN(e, 6)
|
- IS_GEN7(e)
+ IS_GEN(e, 7)
|
- IS_GEN8(e)
+ IS_GEN(e, 8)
|
- IS_GEN9(e)
+ IS_GEN(e, 9)
|
- IS_GEN10(e)
+ IS_GEN(e, 10)
|
- IS_GEN11(e)
+ IS_GEN(e, 11)
)
v2: use IS_GEN rather than GT_GEN and compare to info.gen rather than
using the bitmask
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-2-lucas.demarchi@intel.com
RANGE makes it longer, but clearer. We are also going to add a macro to
check an individual gen, so add the _RANGE prefix here.
Diff generated with:
sed 's/IS_GEN(/IS_GEN_RANGE(/g' drivers/gpu/drm/i915/{*/,}*.{c,h} -i
v2: use IS_GEN rather than GT_GEN
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-1-lucas.demarchi@intel.com
For a lot of use cases we need 64bit sequence numbers. Currently drivers
overload the dma_fence structure to store the additional bits.
Stop doing that and make the sequence number in the dma_fence always
64bit.
For compatibility with hardware which can do only 32bit sequences the
comparisons in __dma_fence_is_later only takes the lower 32bits as significant
when the upper 32bits are all zero.
v2: change the logic in __dma_fence_is_later
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/266927/
Currently we allocate a scratch page for each engine, but since we only
ever write into it for post-sync operations, it is not exposed to
userspace nor do we care for coherency. As we then do not care about its
contents, we can use one page for all, reducing our allocations and
avoid complications by not assuming per-engine isolation.
For later use, it simplifies engine initialisation (by removing the
allocation that required struct_mutex!) and means that we can always rely
on there being a scratch page.
v2: Check that we allocated a large enough scratch for I830 w/a
Fixes: 06e562e7f5 ("drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5") # v4.18.20
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108850
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.18.20+
Convert the per context workaround handling code to run against the newly
introduced common workaround framework and fuse the two to use the
existing smarter list add helper, the one which does the sorted insert and
merges registers where possible.
This completes migration of all four classes of workarounds onto the
common framework.
Existing macros are kept untouched for smaller code churn.
v2:
* Rename to list name ctx_wa_list and move from dev_priv to engine.
v3:
* API rename and parameters tweaking. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133357.10341-1-tvrtko.ursulin@linux.intel.com
Instead of having a separate list of white-listed registers we can
trivially move this to the common workarounds framework.
This brings us one step closer to the goal of driving all workaround
classes using the same code.
v2:
* Use GEM_DEBUG_WARN_ON for the sanity check. (Chris Wilson)
v3:
* API rename. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203125014.3219-6-tvrtko.ursulin@linux.intel.com
