Enable power saving for RTS5250S as following steps:
1.Set 0xFE58 to enable clock power management.
2.Check cfg space whether support L1SS or not.
3.If support L1SS, set 0xFF03 to free clkreq.
4.When entering idle status, enable aspm
and set parameters for L1SS and LTR.
5.Wnen entering run status, disable aspm
and set parameters for L1SS and LTR.
If entering L1SS mode successfully,
electric current will be below 2mA.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the MFD driver for Dollar Cove (TI version) PMIC with
ACPI INT33F5 that is found on some Intel Cherry Trail devices.
The driver is based on the original work by Intel, found at:
https://github.com/01org/ProductionKernelQuilts
This is a minimal version for adding the basic resources. Currently,
only ACPI PMIC opregion and the external power-button are used.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=193891
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds muic of_compatible in order to use the muic device
driver in device tree.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't populate the arrays vcore_val, vpll_val and vaux_val on the
stack, instead make them static const. Makes the object code smaller
by over 370 bytes:
Before:
text data bss dec hex filename
6971 3248 64 10283 282b drivers/mfd/stw481x.o
After:
text data bss dec hex filename
6338 3504 64 9906 26b2 drivers/mfd/stw481x.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Push the system suspend/resume callbacks of intel-lpss to the late
suspend/early resume stages to allow child device callbacks to be
pushed to the late/early stages of suspend/resume too, so as to
make it possible to avoid resuming the children if they are runtime-
suspended during system suspend going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Tested-by: Rajat Jain <rajatja@google.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This code has now been moved to the audio subsystem so is no longer
required in the MFD code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM9705, WM9712 and WM9713 are highly integrated codecs, with an
audio codec, DAC and ADC, GPIO unit and a touchscreen interface.
Historically the support was spread across drivers/input/touchscreen and
sound/soc/codecs. The sharing was done through ac97 bus sharing. This
model will not withstand the new AC97 bus model, where codecs are
discovered on runtime.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
- Drop the P-state selection algorithm based on a PID controller
from intel_pstate and make it use the same P-state selection
method (based on the CPU load) for all types of systems in the
active mode (Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to
take cross-CPU utilization updates into account and modify the
schedutil governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the
mediatek cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points
(OPP) DT bindings and update its whitelist of supported systems
(Viresh Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen,
Finley Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to
make it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number
of items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on
x86 in a more straightforward way and to use %pOF instead of
full_name (Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor
issues (Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mAiV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
This commits makes the intel_soc_pmic_core code check the _HRV of the
ACPI-firmware-node and selects intel_soc_pmic_config_byt_crc resp.
intel_soc_pmic_config_cht_crc based on this.
This fixes the Bay Trail specific ACPI OpRegion code causing problems
on Cherry Trail devices. Specifically this was causing the external
microsd slot on a Dell Venue 8 5855 (Cherry Trail version) to not work
and the eMMC to become unreliable and throw lots of errors.
Fixes: 5165238460 ("mfd: intel_soc_pmic: Core driver")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
Looking at the android x86 kernel sources where most of the Crystal Cove
code comes from, it talks about "Valley View", "Bay Trail" and / or BYT
without ever mentioning Cherry Trail, with the exception of the regulator
driver. The Asus Zenfone-2 kernel code has 2 regulator drivers, one
for Crystal Cove and one for what it calls Crystal Cove Plus. The
Crystal Cove Plus regulator driver is the only one to mention Cherry
Trail and that driver uses different register addresses then the
normal (Bay Trail) Crystal Cove regulator driver, showing that at
least the regulator register addresses are different.
The GPIO code should work on both, and the PWM code is known to work on
both and is necessary for backlight control on some Cherry Trail devices.
Testing has shown that the ACPI OpRegion code otoh is causing problems
on Cherry Trail devices, which is not surprising as it deals with the
regulators and those have different register addresses on CHT.
Specifically the ACPI OpRegion code causes the external microsd slot on
a Dell Venue 8 5855 (Cherry Trail version) to not work and the eMMC to
become unreliable and throw lots of errors.
This commit replaces the single mfd_cell array currently used for Crystal
Cove with 2 separate arrays, one for the Bay Trail variant and one for
the Cherry Trail variant, note that the Cherry Trail version of the array
only contains gpio and pwm cells. The PMIC OpRegion cell is deliberately
not included and drivers for the other cells in the Bay Trail cell array
were never upstreamed.
Fixes: 7cf0a66f32 ("mfd: intel_soc_pmic: Crystal Cove support")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
gcc-8 notices that the register number calculation is wrong
when the offset is an 'u8' but the number is larger than 256:
drivers/mfd/omap-usb-tll.c: In function 'omap_tll_init':
drivers/mfd/omap-usb-tll.c:90:46: error: overflow in conversion from 'int' to 'u8 {aka unsigned char}' chages value from 'i * 256 + 2070' to '22' [-Werror=overflow]
This addresses it by always using a 32-bit offset number for
the register. This is apparently an old problem that previous
compilers did not find.
Fixes: 16fa3dc75c ("mfd: omap-usb-tll: HOST TLL platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
spi_device_id are not supposed to change at runtime. All functions
working with spi_device_id provided by <linux/i2c.h> work with
const spi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 274e43edcd ("mfd: intel-lpss: Do not put device in reset
state on suspend") changed the behavior on suspend by not putting LPSS
controllers into reset. This was done because S3/S0ix fail if UART
device is put into reset and no_console_suspend flag is enabled.
Because of the above change, I2C controller gets into a bad state if
it observes that the I2C lines are pulled low when power to I2C device
is cut off during suspend (generally, I2C lines are pulled to power
rail of the I2C device in order to ensure that there is no leakage
because of the pulls when device is turned off). This results in the
controller timing out for all future I2C operations after resume. It
is primarily because of the following sequence of operations:
During suspend:
1. I2C controller is disabled, but it is not put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
==> At this point the I2C controller gets into a bad state
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled.
However, even after enabling the I2C controller, all future I2C xfers
fail since the controller is in a bad state and does not attempt to
make any transactions and hence times out.
In order to ensure that the controller does not get into a bad state,
this change puts it into reset if the controller type is not
UART. With this change, the order of operations is:
During suspend:
1. I2C controller is disabled and put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled and taken out of reset.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a missing PCI ID of the Intel Sunrise Point chipset to the Intel LPSS driver.
It fixes a bug causing the touchpad of the Lenovo Yoga 720-15 not to be recognized.
See also bug 1700657 on bugs.launchpad.net.
Many thanks to CoolStar, who found this solution!
Reported-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: Mike Schwartz <mykesx@gmail.com>
Tested-by: Björn Dahlgren <bjodah@gmail.com>
Signed-off-by: Florian R. Hölzlwimmer <git.ich@frhoelzlwimmer.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
we must disable clock, if t7l66xb_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PMIC provides ACPI OpRegions which must be available for other
drivers' PS0 / PS3 methods early-on as such it must be builtin as the
Kconfig help text already states.
Somehow its Kconfig option ended up being a tristate though, this fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes missing mfd_remove_devices() call when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS68470 device is an advanced power management
unit that powers a Compact Camera Module (CCM),
generates clocks for image sensors, drives a dual
LED for Flash and incorporates two LED drivers for
general purpose indicators.
This patch adds support for TPS68470 mfd device.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
At least on Lenovo Thinkpad Yoga, the BIOS seems to monitor the SPI-NOR
write protection bit and if it is flipped to read/write it assumes the
BIOS configuration was changed on next reboot. It then, for unknown
reasons, resets the BIOS settings back to default.
We can prevent this by just leaving the write protection bit intact and
let the SPI-NOR driver know whether the device is writable or not. In
case of this particular Lenovo the SPI-NOR flash will be exposed as
read-only.
Fixes: ff00d7a32a ("mfd: lpc_ich: Add support for SPI serial flash host controller")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195951
Reported-by: Abdó Roig-Marange <abdo.roig@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22e ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to their datasheets, the AXP221, AXP223, AXP288, AXP803,
AXP809 and AXP813 PEK have different values for startup time bits from
the AXP20X, let's use the platform device id with the correct values.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP813 PMIC is normally used with Allwinner's A83T SoC.
It has the same range of functions as other X-Powers PMICs, such as
DC-DC buck converter and linear regulator outputs, AC-IN and VBUS
power supplies, power button trigger, GPIOs, ADCs, and a battery
charger.
Note that the IRQ table given in the datasheet is incorrect: in IRQ
enable/status registers 1, there are separate IRQs for ACIN and VBUS,
instead of bits [7:5] being the same as bits [4:2]. So it shares the
same IRQs as the AXP803, rather than the AXP288.
This patch adds basic mfd support for it, with only the power button
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the MFD part of the ROHM BD9571MWV-M PMIC driver and MAINTAINERS
entry. The MFD part only specifies the regmap bits for the PMIC and
binds the subdevs together.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for HiSilicon Hi6421v530 PMIC. Hi6421v530 communicates with
main SoC via memory-mapped I/O.
Hi6421v530 and Hi6421 are PMIC chips from the same vendor, HiSilicon,
but at different revisions. They share the same memory-mapped I/O
design. They differ in integrated devices, such as regulator details,
LDO voltage points.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update dev_err messages to make them more readable.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change license text to a shorter form of GPLv2.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MTF_CORE should be enabled when driver is enabled.
Without this patch you can configure:
CONFIG_MFD_CORE is not set
CONFIG_MFD_TPS65086=y
... which ends up with compilation error:
drivers/mfd/tps65086.o: In function `tps65086_probe':
drivers/mfd/tps65086.c:110: undefined reference to `mfd_add_devices'
drivers/mfd/tps65086.c:110:(.text+0x128): relocation truncated to fit: \
R_AARCH64_CALL26 against undefined symbol `mfd_add_devices'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
16298 1009 184 17491 4453 drivers/mfd/ab8500-core.o
File size After adding 'const':
text data bss dec hex filename
16490 817 184 17491 4453 drivers/mfd/ab8500-core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
if 'max8998_i2c_parse_dt_pdata() fails (when out of memory), a NULL
pointer dereference will occur in the error handling code.
Return directly instead.
Fixes: ee999fb3f17f("mfd: max8998: Add support for Device Tree")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Drop static on a local variable, when the variable is initialized before
any use, on every possible execution path through the function. The static
has no benefit, and dropping it reduces the code size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
2579 240 16 2835 b13 drivers/mfd/max8925-i2c.o
after:
text data bss dec hex filename
2531 240 8 2779 adb drivers/mfd/max8925-i2c.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible that under heavy system load, the counter in the completion
struct, used for waiting for end of AD conversion, gets incremented twice.
To make sure the driver recovers from this situation, the completion struct
should be reinitialized.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't populate the arrays depath and cd_mask on the stack but make
them static const. Makes the object code smaller:
text data bss dec hex filename
25413 7216 448 33077 8135 drivers/mfd/rtsx_pcr.o
text data bss dec hex filename
25151 7360 448 32959 80bf drivers/mfd/rtsx_pcr.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Saying it "returns the result" seems tautological. The read function
does not return num_bytes on success, it returns zero on success. I
noticed this discrepancy because some of the callers were checking for
>= 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 Low-Power Timer hardware block can be used for:
- PWM generation
- IIO trigger (in sync with PWM)
- IIO quadrature encoder counter
PWM and IIO timer configuration are mixed in the same registers so
we need a multi fonction driver to be able to share those registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- New driver for Lantiq CPU temperature sensor
- New driver for IBM CFF power supply
- New PMBus driver for TPS53679
- Add support for LM5066I lm25066 PMBus driver
- Add support for Intel VID protocol VR13 to PMBus drivers
- Add support for CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 to jc42 driver
- Cleanup and minor improvements in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DZJP
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new drivers:
- Lantiq CPU temperature sensor
- IBM CFF power supply
- TPS53679 PMBus driver
- new support:
- LM5066I (lm25066 PMBus driver)
- Intel VID protocol VR13 (PMBus drivers)
- CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 (jc42 driver)
- cleanup and minor improvements in several drivers
* tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (36 commits)
hwmon: (ltq-cputemp) add cpu temp sensor driver
hwmon: (ltq-cputemp) add devicetree bindings documentation
hwmon: (pmbus) Add support for Texas Instruments tps53679 device
hwmon: (asc7621) make several arrays static const
hwmon: (pmbus/lm25066) Add support for TI LM5066I
hwmon: (pmbus/lm25066) Offset coefficient depends on CL
hwmon: (pmbus) Add support for Intel VID protocol VR13
Documentation: hwmon: Document the IBM CFF power supply
hwmon: (pmbus) Add IBM Common Form Factor (CFF) power supply driver
dt-bindings: hwmon: Document the IBM CCF power supply version 1
hwmon: (ftsteutates) constify i2c_device_id
hwmon: da9052: Add support for TSI channel
mfd: da9052: Make touchscreen registration optional
hwmon: da9052: Replace S_IRUGO with 0444
mfd: da9052: Add register details for TSI
hwmon: (aspeed-pwm) add THERMAL dependency
hwmon: (pmbus) Add debugfs for status registers
hwmon: (aspeed-pwm-tacho) cooling device support.
Documentation: dt-bindings: aspeed-pwm-tacho cooling device.
hwmon: (pmbus): Add generic alarm bit for iin and pin
...
* pm-cpufreq: (33 commits)
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpufreq: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
cpufreq: dbx500: Delete obsolete driver
mfd: db8500-prcmu: Get rid of cpufreq dependency
cpufreq: enable the DT cpufreq driver on the Ux500
cpufreq: Loongson2: constify platform_device_id
cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
cpufreq: remove setting of policy->cpu in policy->cpus during init
cpufreq: mediatek: add support of cpufreq to MT7622 SoC
cpufreq: mediatek: add cleanups with the more generic naming
cpufreq: rcar: Add support for R8A7795 SoC
cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
cpufreq: s5pv210: add missing of_node_put()
cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
...
A small number of bugfixes, again nothing serious.
- Alexander Dahl found multiple bugs in the Atmel memory interface driver
- A randconfig build fix for at91 was incomplete, the second
attempt fixes the remaining corner case
- One fix for the TI Keystone queue handler
- The Odroid XU4 HDMI port (added in 4.13) needs a small
DT fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=efYA
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A small number of bugfixes, again nothing serious.
- Alexander Dahl found multiple bugs in the Atmel memory interface
driver
- A randconfig build fix for at91 was incomplete, the second attempt
fixes the remaining corner case
- One fix for the TI Keystone queue handler
- The Odroid XU4 HDMI port (added in 4.13) needs a small DT fix"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: add needs-hpd for Odroid-XU3/4
ARM: at91: don't select CONFIG_ARM_CPU_SUSPEND for old platforms
soc: ti: knav: Add a NULL pointer check for kdev in knav_pool_create
memory: atmel-ebi: Fix smc cycle xlate converter
memory: atmel-ebi: Allow t_DF timings of zero ns
memory: atmel-ebi: Fix smc timing return value evaluation
The ARMSS clock, also known as the operating point of the
CPU, should not cross-depend on cpufreq like this. Move
the code to use just frequencies and remove the false
frequency (1GHz) and put in the actual frequency provided
by the ARMSS clock (998400000 Hz) as part of the process.
After this and the related cpufreq patch, the DB8500 will
simply use the standard DT cpufreq driver to change the
operating points through the common clock framework using
the ARMSS clock.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch was applied to the MFD twice, causing unwanted behavour.
This reverts commit b77eb79acc.
Fixes: b77eb79acc ("mfd: da9061: Fix to remove BBAT_CONT register from chip model")
Reported-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the touchscreen pins are used as general purpose analogue
input, the touchscreen driver should not be used. The pins
will be handled by the existing hwmon driver instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK805 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clocking
Both RK808 and RK805 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
the rk8xx chip id is:
((MSB << 8) | LSB) & 0xfff0
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The converter function for translating ns timings in register values was
initialized with a wrong function pointer. This resulted in wrong
register values also for the setup and pulse registers when configuring
the EBI interface trough dts.
Includes a small fix in a comment of the smc driver, which was probably
just a copy'n'paste mistake.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have a
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have a
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's not correct to encode the subsystem in the I2C device name, so
drop the -mfd suffix. To maintain bisect-ability, change driver and
platform code / DTS users in the same patch.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Changes in this pull request are around catching up
cros_ec with the internal chromeos-kernel versions of
cros_ec, cros_ec_lpc, and cros_ec_lightbar.
Also, switching maintainership from olof to bleung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QtSr
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
"Changes in this pull request are around catching up cros_ec with the
internal chromeos-kernel versions of cros_ec, cros_ec_lpc, and
cros_ec_lightbar.
Also, switching maintainership from olof to bleung"
* tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome : Add myself as Maintainer
platform/chrome: cros_ec_lightbar - hide unused PM functions
cros_ec: Don't signal wake event for non-wake host events
cros_ec: Fix deadlock when EC is not responsive at probe
cros_ec: Don't return error when checking command version
platform/chrome: cros_ec_lightbar - Avoid I2C xfer to EC during suspend
platform/chrome: cros_ec_lightbar - Add userspace lightbar control bit to EC
platform/chrome: cros_ec_lightbar - Control of suspend/resume lightbar sequence
platform/chrome: cros_ec_lightbar - Add lightbar program feature to sysfs
platform/chrome: cros_ec_lpc: Add MKBP events support over ACPI
platform/chrome: cros_ec_lpc: Add power management ops
platform/chrome: cros_ec_lpc: Add support for GOOG004 ACPI device
platform/chrome: cros_ec_lpc: Add support for mec1322 EC
platform/chrome: cros_ec_lpc: Add R/W helpers to LPC protocol variants
mfd: cros_ec: Add support for dumping panic information
cros_ec_debugfs: Pass proper struct sizes to cros_ec_cmd_xfer()
mfd: cros_ec: add debugfs, console log file
mfd: cros_ec: Add EC console read structures definitions
mfd: cros_ec: Add helper for event notifier.
Pull input updates from Dmitry Torokhov:
- a new driver for STM FingerTip touchscreen
- a new driver for D-Link DIR-685 touch keys
- updated list of supported devices in xpad driver
- other assorted updates and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (23 commits)
MAINTAINERS: update input subsystem patterns
Input: introduce KEY_ASSISTANT
Input: xpad - sync supported devices with XBCD
Input: xpad - sync supported devices with 360Controller
Input: xen-kbdfront - use string constants from PV protocol
Input: stmfts - mark all PM functions as __maybe_unused
Input: add support for the STMicroelectronics FingerTip touchscreen
Input: add D-Link DIR-685 touchkeys driver
Input: s3c2410_ts - handle return value of clk_prepare_enable
Input: axp20x-pek - add wakeup support
Input: synaptics-rmi4 - use %phN to form F34 configuration ID
Input: synaptics-rmi4 - change a char type to u8
Input: sparse-keymap - remove sparse_keymap_free()
Input: tsc2007 - move header file out of I2C realm
Input: mms114 - move header file out of I2C realm
Input: mcs - move header file out of I2C realm
Input: lm8323 - move header file out of I2C realm
Input: elantech - force relative mode on a certain module
Input: elan_i2c - add support for fetching chip type on newer hardware
Input: elan_i2c - check if device is there before really probing
...
Pull MFD updates from Lee Jones:
"New Drivers:
- Intel Cherry Trail Whiskey Cove PMIC
- TI LP87565 PMIC
New Device Support:
- Add support for Cannonlake to intel-lpss-pci
- Add support for Simatic IOT2000 to intel_quark_i2c_gpio
New Functionality:
- Add Regulator support (axp20x)
Fix-ups:
- Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec)
- Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core)
- Provide deregistration on unbind (rn5t618)
- Rework DT code/documentation (arizona)
- Constify things (fsl-imx25-tsadc)
- MAINTAINERS updates (DA9062/61)
- Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C)
- Switch to DMI matching (intel_quark_i2c_gpio)
- Provide an appropriate level of error checking (wm831x-{i2c,spi},
twl4030-irq, tc6393xb)
- Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc,
stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc,
exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099,
motorola-cpcap)"
[ Skipped the last commit in that series that added eight thousand
lines of pointless repeated register definitions. - Linus ]
* tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits)
mfd: Add LP87565 PMIC support
mfd: cros_ec: Free IRQ on exit
dt-bindings: vendor-prefixes: Add arctic to vendor prefix
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: axp20x-i2c: Document that this must be builtin on x86
mfd: Add Cherry Trail Whiskey Cove PMIC driver
mfd: tc6393xb: Handle return value of clk_prepare_enable
mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform
mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency
mfd: motorola-cpcap: Use devm_of_platform_populate()
mfd: smsc-ece: Use devm_of_platform_populate()
mfd: qcom-spmi-pmic: Use devm_of_platform_populate()
mfd: palmas: Use devm_of_platform_populate()
mfd: exynos: Use devm_of_platform_populate()
mfd: fsl-imx25: Use devm_of_platform_populate()
mfd: cros_ec: Use devm_of_platform_populate()
mfd: atmel: Use devm_of_platform_populate()
mfd: stm32-timers: Use devm_of_platform_populate()
mfd: intel_soc_pmic: Select designware i2c-bus driver
...
The LP87565 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Configurable Bucks(Single and multi-phase).
- Configurable General Purpose Output Signals (GPO).
The LP87565-Q1 variant device uses two 2-phase outputs configuration,
Buck0 is master for Buck0/1 output and Buck2 is master for Buck2/3
output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently we request the irq when probing, but never free it. So after
unbind ec driver, this irq will be left requested, which would break
the next bind:
[ 2683.338437] genirq: Flags mismatch irq 64. 00002008 (chromeos-ec) vs. 00002008 (chromeos-ec)
[ 2683.338591] cros-ec-spi spi5.0: request irq 64: error -16
[ 2683.338610] cros-ec-spi spi5.0: cannot register EC
[ 2683.338656] cros-ec-spi: probe of spi5.0 failed with error -16
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On x86 the AXP288 PMIC provides an ACPI OpRegion handler, which must be
available before other drivers using it are loaded, which can only be
ensured if the MFD, OpRegion and i2c-bus drivers are built-in.
Since the AXP20x MFD code is used on non x86 too we cannot simply change
this into a bool, I've tried some Kconfig magic with if x86 but I could
not get this working correctly, so this commit just documents that this
should be built-in on x86, which fixes errors like these during boot:
mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion]
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-2
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b
acpi 80860F14:02: Failed to change power state to D0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add mfd driver for Intel CHT Whiskey Cove PMIC, based on various non
upstreamed CHT Whiskey Cove PMIC patches.
This is a somewhat minimal version which adds irqchip support and cells
for: ACPI PMIC opregion support, the i2c-controller driving the external
charger irc and the pwrsrc/extcon block.
Further cells can be added in the future if/when drivers are upstreamed
for them.
[The above patch caused a build error on some archetectures]
From: Arnd Bergmann <arnd@arndb.de>
I ran into a build error on ARM with a platform that has a non-standard
clk implementation:
drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.
This turns all three into 'depends on', as it should be.
Finally, we can limit the build to x86, unless we are compile testing.
First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The SIMATIC IOT2020 and IOT2040 are derived from the Galileo Gen2 board
and share its I2C frequency.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Avoids reimplementation of DMI matching in intel_quark_i2c_setup.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Usage of devm_of_platform_populate() simplify driver code
by allowing to delete cpcap_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Usage of devm_of_platform_populate() simplify driver code
by allowing to delete pmic_spmi_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_of_platform_populate() instead of of_platform_populate()
and suppress stm32_timers_remove() which become useless.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Crystal Cove PMIC provides an ACPI OPRegion handler, which must be
available before other drivers using it are loaded, which is why
INTEL_SOC_PMIC is a bool.
Just having the driver is not enough, the driver for the i2c-bus must
also be built in, to ensure this, this patch adds a select for it.
This fixes errors like these during boot:
mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion] (20170119/evregion-166)
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-299)
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93543b0cde10), AE_NOT_EXIST (20170119/psparse-543)
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b0b5cd0), AE_NOT_EXIST (20170119/psparse-543)
acpi 80860F14:02: Failed to change power state to D0
While at it this patch also changes the human readable name of the Kconfig
option to make clear the INTEL_SOC_PMIC option selects support for the
Intel Crystal Cove PMIC and documents why this is a bool.
[The above patch caused a build error on some archetectures]
From: Arnd Bergmann <arnd@arndb.de>
I ran into a build error on ARM with a platform that has a non-standard
clk implementation:
drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.
This turns all three into 'depends on', as it should be.
Finally, we can limit the build to x86, unless we are compile testing.
First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As silently failing isn't that nice, emit an error message at a place
that was silent on failure up to now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add NULL check before dereferencing pointer of_id in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1408830
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add NULL check before dereferencing pointer of_id in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1408829
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The request should be resent when DMA transfer error occurred.
For rts5227, the clock rate needs to be reduced when error occurred.
Signed-off-by: Steven Feng <steven_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As axp20x-regulator now supports AXP803, add a cell for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the restart handler registered in probe on device remove.
Fixes: a370f60a58 ("mfd: rn5t618: Register restart handler")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since a copy of the pdata was added into the core struct in
commit f6dd8449cd ("mfd: wm831x: Add basic device tree binding")
the pdata pointer in probe can no longer be NULL. As such remove
the redundant checks for this case.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These hexdumps get printed no matter if CONFIG_DEBUG is set or
not. Just get rid of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Cannonlake PCH has the same LPSS than Intel Kabylake. Add the new IDs
to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The subset of wake-enabled host events is defined by the EC, but the EC
may still send non-wake host events if we're in the process of
suspending. Get the mask of wake-enabled host events from the EC and
filter out non-wake events to prevent spurious aborted suspend
attempts.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Whishkey cove PMIC has support to mask/unmask interrupts at two levels.
At first level we can mask/unmask interrupt domains like TMU, GPIO, ADC,
CHGR, BCU THERMAL and PWRBTN and at second level, it provides facility
to mask/unmask individual interrupts belong each of this domain. For
example, in case of TMU, at first level we have TMU interrupt domain,
and at second level we have two interrupts, wake alarm, system alarm that
belong to the TMU interrupt domain.
Currently, in this driver all first level IRQs are registered as part of
IRQ chip(bxtwc_regmap_irq_chip). By default, after you register the IRQ
chip from your driver, all IRQs in that chip will masked and can only be
enabled if that IRQ is requested using request_irq() call. This is the
default Linux IRQ behavior model. And whenever a dependent device that
belongs to PMIC requests only the second level IRQ and not explicitly
unmask the first level IRQ, then in essence the second level IRQ will
still be disabled. For example, if TMU device driver request wake_alarm
IRQ and not explicitly unmask TMU level 1 IRQ then according to the default
Linux IRQ model, wake_alarm IRQ will still be disabled. So the proper
solution to fix this issue is to use the chained IRQ chip concept. We
should chain all the second level chip IRQs to the corresponding first
level IRQ. To do this, we need to create separate IRQ chips for every
group of second level IRQs.
In case of TMU, when adding second level IRQ chip, instead of using PMIC
IRQ we should use the corresponding first level IRQ. So the following
code will change from
ret = regmap_add_irq_chip(pmic->regmap, pmic->irq, ...)
to,
virq = regmap_irq_get_virq(&pmic->irq_chip_data, BXTWC_TMU_LVL1_IRQ);
ret = regmap_add_irq_chip(pmic->regmap, virq, ...)
In case of Whiskey Cove Type-C driver, Since USBC IRQ is moved under
charger level2 IRQ chip. We should use charger IRQ chip(irq_chip_data_chgr)
to get the USBC virtual IRQ number.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Revieved-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cleanup the resource allocation/free code in probe function by using
devm_* calls.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently all PMIC GPIO domain IRQs are consumed by the same
device(bxt_wcove_gpio), so there is no need to export them as
separate interrupts. We can just export only the first level
GPIO IRQ(BXTWC_GPIO_LVL1_IRQ) as an IRQ resource and let the
GPIO device driver(bxt_wcove_gpio) handle the GPIO sub domain
IRQs based on status value of GPIO level2 interrupt status
register. Also, just using only the first level IRQ will eliminate
the bug involved in requesting only the second level IRQ and not
explicitly enable the first level IRQ. For more info on this
issue please read the details at,
https://lkml.org/lkml/2017/2/27/148
This patch also makes relevant change in Whiskey cove GPIO driver to
use only first level PMIC GPIO IRQ.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since all second level thermal IRQs are consumed by the same
device(bxt_wcove_thermal), there is no need to expose them as separate
interrupts. We can just export only the first level IRQs for thermal and
let the device(bxt_wcove_thermal) driver handle the second level IRQs
based on thermal interrupt status register. Also, just using only the
first level IRQ will eliminate the bug involved in requesting only the
second level IRQ and not explicitly enable the first level IRQ. For
more info on this issue please read the details at,
https://lkml.org/lkml/2017/2/27/148
This patch also makes relevant change in bxt_wcove_thermal driver to use
only first level PMIC thermal IRQ.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TMU interrupts are registered as a separate interrupt chip, and
hence it should start its interrupt index(BXTWC_TMU_IRQ) number
from 0. But currently, BXTWC_TMU_IRQ is defined as part of enum
bxtwc_irqs_level2 and its index value is 11. Since this index
value is used when calculating .num_irqs of regmap_irq_chip_tmu,
it incorrectly reports number of IRQs as 12 instead of actual
value of 1.
This patch fixes this issue by creating new enum of tmu IRQs and
resetting its starting index to 0.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This enables configuring the PMIC's sleep mode via device-tree.
A pointer indirection to sleep mode data is removed, as it simplifies
the implementation slightly. In current kernel tree, platform data
structure is not used outside MFD cell drivers.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
A hardcoded register is accidentally used instead of the register
address passed into the function. Correct this and use the appropriate
variable. This would cause minor issues on wm5102, but all other
devices using this driver would have been unaffected.
Fixes: commit ef84f885e0 ("mfd: arizona: Refactor arizona_poll_reg")
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZK2lrAAoJEHm+PkMAQRiGm3AH/13F1DlIk05aSXHoDr/idIpR
GMHmk3YF+EuFjsL463Sh6s/SSWmz0Lda8euaoB4wCWvQFX2ZjTE+aOd79XlRiZJQ
OTtLkV9I41eXIJUpEOHia7xZiCsbw+usqcHrm1aBoSh5KKV2iQmEOrnJdibqJVOF
eXUMphNK/zFtAd2bKtQSxkaBnOOqsQUgVQSkr2K9rSg25l0KokFC6c5K5IjLn4x9
QgDY4wmMvHrDz0CtpoqlNM4XqbsDJVrFeZGfg6hlMqSRDeXeg4h3Ol0VfIT496RP
QBdrDb6hWO+HKt9B0M+7Q+8a/Fsw+5dtpqv1W/Wlr0i4CS6euU8NChAmrpkrqGo=
=m5ba
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc3' into next
Sync with mainline to bring in changes in platform drovers dropping
calls to sparse_keymap_free() so that we can remove it for good.
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
AXP803 is a new PMIC chip produced by X-Powers, usually paired with A64
via RSB bus. The PMIC itself is like AXP288, but with RSB support and
dedicated VBUS and ACIN.
Add support for it in the axp20x mfd driver.
Currently only power key function is supported.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
