The real fix is where we check the bytes we need against how much is
remaining - we also need to check for a journal entry bigger than our
buffer, we'll never write those and it would be bad if we tried to read
one.
Also improve the diagnostic messages.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The code that handles overlapping extents that we've just read back in from disk
was depending on the behaviour of the code that handles overlapping extents as
we're inserting into a btree node in the case of an insert that forced an
existing extent to be split: on insert, if we had to split we'd also insert a
new extent to represent the top part of the old extent - and then that new
extent would get written out.
The code that read the extents back in thus not bother with splitting extents -
if it saw an extent that ovelapped in the middle of an older extent, it would
trim the old extent to only represent the bottom part, assuming that the
original insert would've inserted a new extent to represent the top part.
I still haven't figured out _how_ it can happen, but I'm now pretty convinced
(and testing has confirmed) that there's some kind of an obscure corner case
(probably involving extent merging, and multiple overwrites in different sets)
that breaks this. The fix is to change the mergesort fixup code to split extents
itself when required.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
When extending a metadata space map we should do the first commit whilst
still in bootstrap mode -- a mode where all blocks get allocated in the
new area.
That way the commit overhead is allocated from the newly added space.
Otherwise we risk running out of space.
With this fix, and the previous commit "dm space map common: make sure
new space is used during extend", the following device mapper testsuite
test passes:
dmtest run --suite thin-provisioning -n /resize_metadata_no_io/
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
When extending a low level space map we should update nr_blocks at
the start so the new space is used for the index entries.
Otherwise extend can fail, e.g.: sm_metadata_extend call sequence
that fails:
-> sm_ll_extend
-> dm_tm_new_block -> dm_sm_new_block -> sm_bootstrap_new_block
=> returns -ENOSPC because smm->begin == smm->ll.nr_blocks
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
There may be other parts of the kernel holding a reference on the dm
kobject. We must wait until all references are dropped before
deallocating the mapped_device structure.
The dm_kobject_release method signals that all references are dropped
via completion. But dm_kobject_release doesn't free the kobject (which
is embedded in the mapped_device structure).
This is the sequence of operations:
* when destroying a DM device, call kobject_put from dm_sysfs_exit
* wait until all users stop using the kobject, when it happens the
release method is called
* the release method signals the completion and should return without
delay
* the dm device removal code that waits on the completion continues
* the dm device removal code drops the dm_mod reference the device had
* the dm device removal code frees the mapped_device structure that
contains the kobject
Using kobject this way should avoid the module unload race that was
mentioned at the beginning of this thread:
https://lkml.org/lkml/2014/1/4/83
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The comparison is always true and the compiler optimizes it out anyway.
Milan offered additional context relative to the original commit
784aae735d ("dm: add name and uuid to sysfs") which introduced the code:
"I think it is just relict of some experiments before I committed this
simple embedded sysfs kobj handling".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In case CONFIG_DEBUG_OBJECTS_WORK is defined, it is needed to
call destroy_work_on_stack() which frees the debug object to pair
with INIT_WORK_ONSTACK().
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Internally the mq policy maintains a promotion threshold variable. If
the hit count of a block not in the cache goes above this threshold it
gets promoted to the cache.
This patch introduces three new tunables that allow you to tweak the
promotion threshold by adding a small value. These adjustments depend
on the io type:
read_promote_adjustment: READ io, default 4
write_promote_adjustment: WRITE io, default 8
discard_promote_adjustment: READ/WRITE io to a discarded block, default 1
If you're trying to quickly warm a new cache device you may wish to
reduce these to encourage promotion. Remember to switch them back to
their defaults after the cache fills though.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The pool mode must not be switched until after the corresponding pool
process_* methods have been established. Otherwise, because
set_pool_mode() isn't interlocked with the IO path for performance
reasons, the IO path can end up executing process_* operations that
don't match the mode. This patch eliminates problems like the following
(as seen on really fast PCIe SSD storage when transitioning the pool's
mode from PM_READ_ONLY to PM_WRITE):
kernel: device-mapper: thin: 253:2: reached low water mark for data device: sending event.
kernel: device-mapper: thin: 253:2: no free data space available.
kernel: device-mapper: thin: 253:2: switching pool to read-only mode
kernel: device-mapper: thin: 253:2: switching pool to write mode
kernel: ------------[ cut here ]------------
kernel: WARNING: CPU: 11 PID: 7564 at drivers/md/dm-thin.c:995 handle_unserviceable_bio+0x146/0x160 [dm_thin_pool]()
...
kernel: Workqueue: dm-thin do_worker [dm_thin_pool]
kernel: 00000000000003e3 ffff880308831cc8 ffffffff8152ebcb 00000000000003e3
kernel: 0000000000000000 ffff880308831d08 ffffffff8104c46c ffff88032502a800
kernel: ffff880036409000 ffff88030ec7ce00 0000000000000001 00000000ffffffc3
kernel: Call Trace:
kernel: [<ffffffff8152ebcb>] dump_stack+0x49/0x5e
kernel: [<ffffffff8104c46c>] warn_slowpath_common+0x8c/0xc0
kernel: [<ffffffff8104c4ba>] warn_slowpath_null+0x1a/0x20
kernel: [<ffffffffa001e2c6>] handle_unserviceable_bio+0x146/0x160 [dm_thin_pool]
kernel: [<ffffffffa001f276>] process_bio_read_only+0x136/0x180 [dm_thin_pool]
kernel: [<ffffffffa0020b75>] process_deferred_bios+0xc5/0x230 [dm_thin_pool]
kernel: [<ffffffffa0020d31>] do_worker+0x51/0x60 [dm_thin_pool]
kernel: [<ffffffff81067823>] process_one_work+0x183/0x490
kernel: [<ffffffff81068c70>] worker_thread+0x120/0x3a0
kernel: [<ffffffff81068b50>] ? manage_workers+0x160/0x160
kernel: [<ffffffff8106e86e>] kthread+0xce/0xf0
kernel: [<ffffffff8106e7a0>] ? kthread_freezable_should_stop+0x70/0x70
kernel: [<ffffffff8153b3ec>] ret_from_fork+0x7c/0xb0
kernel: [<ffffffff8106e7a0>] ? kthread_freezable_should_stop+0x70/0x70
kernel: ---[ end trace 3f00528e08ffa55c ]---
kernel: device-mapper: thin: pool mode is PM_WRITE not PM_READ_ONLY like expected!?
dm-thin.c:995 was the WARN_ON_ONCE(get_pool_mode(pool) != PM_READ_ONLY);
at the top of handle_unserviceable_bio(). And as the additional
debugging I had conveys: the pool mode was _not_ PM_READ_ONLY like
expected, it was already PM_WRITE, yet pool->process_bio was still set
to process_bio_read_only().
Also, while fixing this up, reduce logging of redundant pool mode
transitions by checking new_mode is different from old_mode.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The pool's error_if_no_space flag can easily serve the same purpose that
no_free_space did, namely: control whether handle_unserviceable_bio()
will error a bio or requeue it.
This is cleaner since error_if_no_space is established when the pool's
features are processed during table load. So it avoids managing the
no_free_space flag by taking the pool's spinlock.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If the pool runs out of data or metadata space, the pool can either
queue or error the IO destined to the data device. The default is to
queue the IO until more space is added.
An admin may now configure the pool to error IO when no space is
available by setting the 'error_if_no_space' feature when loading the
thin-pool table.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Now that we switch the pool to read-only mode when the data device runs
out of space it causes active writers to get IO errors once we resume
after resizing the data device.
If no_free_space is set, save bios to the 'retry_on_resume_list' and
requeue them on resume (once the data or metadata device may have been
resized).
With this patch the resize_io test passes again (on slower storage):
dmtest run --suite thin-provisioning -n /resize_io/
Later patches fix some subtle races associated with the pool mode
transitions done as part of the pool's -ENOSPC handling. These races
are exposed on fast storage (e.g. PCIe SSD).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Factor out_of_data_space() out of alloc_data_block(). Eliminate the use
of 'no_free_space' as a latch in alloc_data_block() -- this is no longer
needed now that we switch to read-only mode when we run out of data or
metadata space. In a later patch, the 'no_free_space' flag will be
eliminated entirely (in favor of checking metadata rather than relying
on a transient flag).
Move no metdata space handling into metdata_operation_failed(). Set
no_free_space when metadata space is exhausted too. This is useful,
because it offers consistency, for the following patch that will requeue
data IOs if no_free_space.
Also, rename no_space() to retry_bios_on_resume().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Introduce metadata_operation_failed() wrappers, around set_pool_mode(),
to assist with improving the consistency of how metadata failures are
handled. Logging is improved and metadata operation failures trigger
read-only mode immediately.
Also, eliminate redundant set_pool_mode() calls in the two
alloc_data_block() caller's error paths.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Factor check_low_water_mark() out of alloc_data_block().
Change a couple unsigned flags in the pool structure to bool.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Mappings could be processed in descending logical block order,
particularly if buffered IO is used. This could adversely affect the
latency of IO processing. Fix this by adding mappings to the end of the
'prepared_mappings' and 'prepared_discards' lists.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Also, move 'err' member in dm_thin_new_mapping structure to eliminate 4
byte hole (reduces size from 88 bytes to 80).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
DM's persistent-data library is now used my multiple targets so
exclusive references to "pool" or "thin provisioning" need to be
cleaned up. Adjust Kconfig's DM_DEBUG_BLOCK_STACK_TRACING text
and remove "pool" from a block manager error message.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
The "unable to allocate new metadata block" error can be a particularly
verbose error if there is a systemic issue with the metadata device.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Starting with commit c0820cf5ad ("dm: introduce per_bio_data"),
device mapper has the capability to pre-allocate a target-specific
structure with the bio.
This patch changes dm-delay to use this facility instead of a slab cache
and mempool.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A device mapper table is allocated in the following way:
* The function dm_table_create is called, it gets the number of targets
as an argument -- it allocates a targets array accordingly.
* For each target, we call dm_table_add_target.
If we add more targets than were specified in dm_table_create, the
function dm_table_add_target reallocates the targets array. However,
this reallocation code is wrong - it moves the targets array to a new
location, while some target constructors hold pointers to the array in
the old location.
The following DM target drivers save the pointer to the target
structure, so they corrupt memory if the target array is moved:
multipath, raid, mirror, snapshot, stripe, switch, thin, verity.
Under normal circumstances, the reallocation function is not called
(because dm_table_create is called with the correct number of targets),
so the buggy reallocation code is not used.
Prior to the fix "dm table: fail dm_table_create on dm_round_up
overflow", the reallocation code could only be used in case the user
specifies too large a value in param->target_count, such as 0xffffffff.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a snapshot is created and later deleted the origin dm_thin_device's
snapshotted_time will have been updated to reflect the snapshot's
creation time. The 'shared' flag in the dm_thin_lookup_result struct
returned from dm_thin_find_block() is an approximation based on
snapshotted_time -- this is done to avoid 0(n), or worse, time
complexity. In this case, the shared flag would be true.
But because the 'shared' flag reflects an approximation a block can be
incorrectly assumed to be shared (e.g. false positive for 'shared'
because the snapshot no longer exists). This could result in discards
issued to a thin device not being passed down to the pool's underlying
data device.
To fix this we double check that a thin block is really still in-use
after a mapping is removed using dm_pool_block_is_used(). If the
reference count for a block is now zero the discard is allowed to be
passed down.
Also add a 'definitely_not_shared' member to the dm_thin_new_mapping
structure -- reflects that the 'shared' flag in the response from
dm_thin_find_block() can only be held as definitive if false is
returned.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1043527
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
As additional members are added to the dm_thin_new_mapping structure
care should be taken to make sure they get initialized before use.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
Pull block fixes from Jens Axboe:
- fix for a memory leak on certain unplug events
- a collection of bcache fixes from Kent and Nicolas
- a few null_blk fixes and updates form Matias
- a marking of static of functions in the stec pci-e driver
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: support submit_queues on use_per_node_hctx
null_blk: set use_per_node_hctx param to false
null_blk: corrections to documentation
null_blk: warning on ignored submit_queues param
null_blk: refactor init and init errors code paths
null_blk: documentation
null_blk: mem garbage on NUMA systems during init
drivers: block: Mark the functions as static in skd_main.c
bcache: New writeback PD controller
bcache: bugfix for race between moving_gc and bucket_invalidate
bcache: fix for gc and writeback race
bcache: bugfix - moving_gc now moves only correct buckets
bcache: fix for gc crashing when no sectors are used
bcache: Fix heap_peek() macro
bcache: Fix for can_attach_cache()
bcache: Fix dirty_data accounting
bcache: Use uninterruptible sleep in writeback
bcache: kthread don't set writeback task to INTERUPTIBLE
block: fix memory leaks on unplugging block device
bcache: fix sparse non static symbol warning
The old writeback PD controller could get into states where it had throttled all
the way down and take way too long to recover - it was too complicated to really
understand what it was doing.
This rewrites a good chunk of it to hopefully be simpler and make more sense,
and it also pays more attention to units which should make the behaviour a bit
easier to understand.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
There is a possibility for a bucket to be invalidated by the allocator
while moving_gc was copying it's contents to another bucket, if the
bucket only held cached data. To prevent this moving checks for
a stale ptr (to an invalidated bucket), before and after reads.
It it finds one, it simply ignores moving that data. This only
affects bcache if the moving_gc was turned on, note that it's
off by default.
Signed-off-by: Nicholas Swenson <nks@daterainc.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Garbage collector needs to check keys in the writeback keybuf to
make sure it's not invalidating buckets to which the writeback
keys point to.
Signed-off-by: Nicholas Swenson <nks@daterainc.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Removed gc_move_threshold because picking buckets only by
threshold could lead moving extra buckets (ei. if there are
buckets at the threshold that aren't supposed to be moved
do to space considerations).
This is replaced by a GC_MOVE bit in the gc_mark bitmask.
Now only marked buckets get moved.
Signed-off-by: Nicholas Swenson <nks@daterainc.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Dirty data accounting wasn't quite right - firstly, we were adding the key we're
inserting after it could have merged with another dirty key already in the
btree, and secondly we could sometimes pass the wrong offset to
bcache_dev_sectors_dirty_add() for dirty data we were overwriting - which is
important when tracking dirty data by stripe.
NOTE FOR BACKPORTERS: For 3.10 (and 3.11?) there's other accounting fixes
necessary that got squashed in with other patches; the full patch against 3.10
is 408cc2f47eeac93a, available at:
git://evilpiepirate.org/~kent/linux-bcache.git bcache-3.10-writeback-fixes
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
diff --git a/drivers/md/bcache/btree.c b/drivers/md/bcache/btree.c
index 2a46036..4a12b2f 100644
--- a/drivers/md/bcache/btree.c
+++ b/drivers/md/bcache/btree.c
@@ -1817,7 +1817,8 @@ static bool fix_overlapping_extents(struct btree *b, struct bkey *insert,
if (KEY_START(k) > KEY_START(insert) + sectors_found)
goto check_failed;
- if (KEY_PTRS(replace_key) != KEY_PTRS(k))
+ if (KEY_PTRS(k) != KEY_PTRS(replace_key) ||
+ KEY_DIRTY(k) != KEY_DIRTY(replace_key))
goto check_failed;
/* skip past gen */
at the beginning (schedule_timout_interuptible) and others
do his on their own
This prevents wrong load average calculation (load of 1 per thread)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
A fix for possible memory corruption during DM table load, fix a
possible leak of snapshot space in case of a crash, fix a possible
deadlock due to a shared workqueue in the delay target, fix to
initialize read-only module parameters that are used to export metrics
for dm stats and dm bufio.
Quite a few stable fixes were identified for both the thin-provisioning
and caching targets as a result of increased regression testing using
the device-mapper-test-suite (dmts). The most notable of these are the
reference counting fixes for the space map btree that is used by the
dm-array interface -- without these the dm-cache metadata will leak,
resulting in dm-cache devices running out of metadata blocks. Also,
some important fixes related to the thin-provisioning target's
transition to read-only mode on error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSq2pVAAoJEMUj8QotnQNaAzEH/0qpz06SVd3+oTbsWeWxXwax
B0zIZ4HPnaD9FDfSWN+6IdQ6Rkn51cspMBHPxWX0I8pmqOTg7MUM7wbaZZaKT3UW
aDlibzG1O3zBGbkr+Qhbh89fJK5/3xnZXlK0hOyaNI2vz1rA6RThZ2hIeak9xQYr
7USz2bjSMXchwebb0Z01CrRnOkhUFg6yUJURIEu4XFCJmDM/PM9zKogLGYKuZedK
pZePnZhwgkLMn7f9l4lPHk3EcWeD4Nf9WR0lS4eKdbYsvMxm1QE7BpDlVJD0Asjg
/SVOVkgygW18TINMHuw1K0DPdSCo5UZF2HRj1QUD/X4N2BSkio+E1qwF6kT4ltk=
=0Ix+
-----END PGP SIGNATURE-----
Merge tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"A set of device-mapper fixes for 3.13.
A fix for possible memory corruption during DM table load, fix a
possible leak of snapshot space in case of a crash, fix a possible
deadlock due to a shared workqueue in the delay target, fix to
initialize read-only module parameters that are used to export metrics
for dm stats and dm bufio.
Quite a few stable fixes were identified for both the thin-
provisioning and caching targets as a result of increased regression
testing using the device-mapper-test-suite (dmts). The most notable
of these are the reference counting fixes for the space map btree that
is used by the dm-array interface -- without these the dm-cache
metadata will leak, resulting in dm-cache devices running out of
metadata blocks. Also, some important fixes related to the
thin-provisioning target's transition to read-only mode on error"
* tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
dm stats: initialize read-only module parameter
dm bufio: initialize read-only module parameters
dm cache: actually resize cache
dm cache: update Documentation for invalidate_cblocks's range syntax
dm cache policy mq: fix promotions to occur as expected
dm thin: allow pool in read-only mode to transition to read-write mode
dm thin: re-establish read-only state when switching to fail mode
dm thin: always fallback the pool mode if commit fails
dm thin: switch to read-only mode if metadata space is exhausted
dm thin: switch to read only mode if a mapping insert fails
dm space map metadata: return on failure in sm_metadata_new_block
dm table: fail dm_table_create on dm_round_up overflow
dm snapshot: avoid snapshot space leak on crash
dm delay: fix a possible deadlock due to shared workqueue
An old array block could have its reference count decremented below
zero when it is being replaced in the btree by a new array block.
The fix is to increment the old ablock's reference count just before
inserting a new ablock into the btree.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
The old behaviour, returning -EINVAL if a ref_count of 0 would be
decremented, was removed in commit f722063 ("dm space map: optimise
sm_ll_dec and sm_ll_inc"). To fix this regression we return an error
code from the mutator function pointer passed to sm_ll_mutate() and have
dec_ref_count() return -EINVAL if the old ref_count is 0.
Add a DMERR to reflect the potential seriousness of this error.
Also, add missing dm_tm_unlock() to sm_ll_mutate()'s error path.
With this fix the following dmts regression test now passes:
dmtest run --suite cache -n /metadata_use_kernel/
The next patch fixes the higher-level dm-array code that exposed this
regression.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/sysfs_elem_dir/kernfs_elem_dir/
* s/sysfs_elem_symlink/kernfs_elem_symlink/
* s/sysfs_elem_attr/kernfs_elem_file/
* s/sysfs_dirent/kernfs_node/
* s/sd/kn/ in kernfs proper
* s/parent_sd/parent/
* s/target_sd/target/
* s/dir_sd/parent/
* s/to_sysfs_dirent()/rb_to_kn()/
* misc renames of local vars when they conflict with the above
Because md, mic and gpio dig into sysfs details, this patch ends up
modifying them. All are sysfs_dirent renames and trivial. While we
can avoid these by introducing a dummy wrapping struct sysfs_dirent
around kernfs_node, given the limited usage outside kernfs and sysfs
proper, I don't think such workaround is called for.
This patch is strictly rename only and doesn't introduce any
functional difference.
- mic / gpio renames were missing. Spotted by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module parameter stats_current_allocated_bytes in dm-mod is
read-only. This parameter informs the user about memory
consumption. It is not supposed to be changed by the user.
However, despite being read-only, this parameter can be set on
modprobe or insmod command line:
modprobe dm-mod stats_current_allocated_bytes=12345
The kernel doesn't expect that this variable can be non-zero at module
initialization and if the user sets it, it results in warning.
This patch initializes the variable in the module init routine, so
that user-supplied value is ignored.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Some module parameters in dm-bufio are read-only. These parameters
inform the user about memory consumption. They are not supposed to be
changed by the user.
However, despite being read-only, these parameters can be set on
modprobe or insmod command line, for example:
modprobe dm-bufio current_allocated_bytes=12345
The kernel doesn't expect that these variables can be non-zero at module
initialization and if the user sets them, it results in BUG.
This patch initializes the variables in the module init routine, so that
user-supplied values are ignored.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.2+
Commit f494a9c6b1 ("dm cache: cache
shrinking support") broke cache resizing support.
dm_cache_resize() is called with cache->cache_size before it gets
updated to new_size, so it is a no-op. But the dm-cache superblock is
updated with the new_size even though the backing dm-array is not
resized. Fix this by passing the new_size to dm_cache_resize().
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Micro benchmarks that repeatedly issued IO to a single block were
failing to cause a promotion from the origin device to the cache. Fix
this by not updating the stats during map() if -EWOULDBLOCK will be
returned.
The mq policy will only update stats, consider migration, etc, once per
tick period (a unit of time established between dm-cache core and the
policies).
When the IO thread calls the policy's map method, if it would like to
migrate the associated block it returns -EWOULDBLOCK, the IO then gets
handed over to a worker thread which handles the migration. The worker
thread calls map again, to check the migration is still needed (avoids a
race among other things). *BUT*, before this fix, if we were still in
the same tick period the stats were already updated by the previous map
call -- so the migration would no longer be requested.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A thin-pool may be in read-only mode because the pool's data or metadata
space was exhausted. To allow for recovery, by adding more space to the
pool, we must allow a pool to transition from PM_READ_ONLY to PM_WRITE
mode. Otherwise, running out of space will render the pool permanently
read-only.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
If the thin-pool transitioned to fail mode and the thin-pool's table
were reloaded for some reason: the new table's default pool mode would
be read-write, though it will transition to fail mode during resume.
When the pool mode transitions directly from PM_WRITE to PM_FAIL we need
to re-establish the intermediate read-only state in both the metadata
and persistent-data block manager (as is usually done with the normal
pool mode transition sequence: PM_WRITE -> PM_READ_ONLY -> PM_FAIL).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Rename commit_or_fallback() to commit(). Now all previous calls to
commit() will trigger the pool mode to fallback if the commit fails.
Also, check the error returned from commit() in alloc_data_block().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Switch the thin pool to read-only mode in alloc_data_block() if
dm_pool_alloc_data_block() fails because the pool's metadata space is
exhausted.
Differentiate between data and metadata space in messages about no
free space available.
This issue was noticed with the device-mapper-test-suite using:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/
The quantity of errors logged in this case must be reduced.
before patch:
device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
<snip ... these repeat for a _very_ long while ... >
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: commit failed: error = -28
device-mapper: thin: 253:4: switching pool to read-only mode
after patch:
device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: no free metadata space available.
device-mapper: thin: 253:4: switching pool to read-only mode
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
Switch the thin pool to read-only mode when dm_thin_insert_block() fails
since there is little reason to expect the cause of the failure to be
resolved without further action by user space.
This issue was noticed with the device-mapper-test-suite using:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/
The quantity of errors logged in this case must be reduced.
before patch:
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
<snip ... these repeat for a long while ... >
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: thin: 253:4: no free metadata space available.
device-mapper: thin: 253:4: switching pool to read-only mode
after patch:
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: dm_thin_insert_block() failed: error = -28
device-mapper: thin: 253:4: switching pool to read-only mode
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The dm_round_up function may overflow to zero. In this case,
dm_table_create() must fail rather than go on to allocate an empty array
with alloc_targets().
This fixes a possible memory corruption that could be caused by passing
too large a number in "param->target_count".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
There is a possible leak of snapshot space in case of crash.
The reason for space leaking is that chunks in the snapshot device are
allocated sequentially, but they are finished (and stored in the metadata)
out of order, depending on the order in which copying finished.
For example, supposed that the metadata contains the following records
SUPERBLOCK
METADATA (blocks 0 ... 250)
DATA 0
DATA 1
DATA 2
...
DATA 250
Now suppose that you allocate 10 new data blocks 251-260. Suppose that
copying of these blocks finish out of order (block 260 finished first
and the block 251 finished last). Now, the snapshot device looks like
this:
SUPERBLOCK
METADATA (blocks 0 ... 250, 260, 259, 258, 257, 256)
DATA 0
DATA 1
DATA 2
...
DATA 250
DATA 251
DATA 252
DATA 253
DATA 254
DATA 255
METADATA (blocks 255, 254, 253, 252, 251)
DATA 256
DATA 257
DATA 258
DATA 259
DATA 260
Now, if the machine crashes after writing the first metadata block but
before writing the second metadata block, the space for areas DATA 250-255
is leaked, it contains no valid data and it will never be used in the
future.
This patch makes dm-snapshot complete exceptions in the same order they
were allocated, thus fixing this bug.
Note: when backporting this patch to the stable kernel, change the version
field in the following way:
* if version in the stable kernel is {1, 11, 1}, change it to {1, 12, 0}
* if version in the stable kernel is {1, 10, 0} or {1, 10, 1}, change it
to {1, 10, 2}
Userspace reads the version to determine if the bug was fixed, so the
version change is needed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current series. It contains:
- A fix for a use-after-free of a request in blk-mq. From Ming Lei
- A fix for a blk-mq bug that could attempt to dereference a NULL rq
if allocation failed
- Two xen-blkfront small fixes
- Cleanup of submit_bio_wait() type uses in the kernel, unifying
that. From Kent
- A fix for 32-bit blkg_rwstat reading. I apologize for this one
looking mangled in the shortlog, it's entirely my fault for missing
an empty line between the description and body of the text"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix use-after-free of request
blk-mq: fix dereference of rq->mq_ctx if allocation fails
block: xen-blkfront: Fix possible NULL ptr dereference
xen-blkfront: Silence pfn maybe-uninitialized warning
block: submit_bio_wait() conversions
Update of blkg_stat and blkg_rwstat may happen in bh context
Move the bio->bi_remaining increment into dm_unhook_bio() so the
overwrite_endio() handler works as expected.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes the following sparse warning:
drivers/md/bcache/btree.c:2220:5: warning:
symbol 'btree_insert_fn' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
commit 566c09c534 raid5: relieve lock contention in get_active_stripe()
modified the locking in get_active_stripe() reducing the range
protected by the (highly contended) device_lock.
Unfortunately it reduced the range too much opening up some races.
One race can occur if get_priority_stripe runs between the
test on sh->count and device_lock being taken.
This will mean that sh->lru is not empty while get_active_stripe
thinks ->count is zero resulting in a 'BUG' firing.
Another race happens if __release_stripe is called immediately
after sh->count is tested and found to be non-zero. If STRIPE_HANDLE
is not set, get_active_stripe should increment ->active_stripes
when it increments ->count from 0, but as it didn't think it was 0,
it doesn't.
Extending device_lock to cover the test on sh->count close these
races.
While we are here, fix the two BUG tests:
-If count is zero, then lru really must not be empty, or we've
lock the stripe_head somehow - no other tests are relevant.
-STRIPE_ON_RELEASE_LIST is completely independent of ->lru so
testing it is pointless.
Reported-and-tested-by: Brassow Jonathan <jbrassow@redhat.com>
Reviewed-by: Shaohua Li <shli@kernel.org>
Fixes: 566c09c534
Signed-off-by: NeilBrown <neilb@suse.de>
commit 7a0a5355cb md: Don't test all of mddev->flags at once.
made most tests on mddev->flags safer, but missed one.
When
commit 260fa034ef md: avoid deadlock when dirty buffers during md_stop.
added MD_STILL_CLOSED, this caused md_check_recovery to misbehave.
It can think there is something to do but find nothing. This can
lead to the md thread spinning during array shutdown.
https://bugzilla.kernel.org/show_bug.cgi?id=65721
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com>
Fixes: 260fa034ef
Cc: stable@vger.kernel.org (3.12)
Signed-off-by: NeilBrown <neilb@suse.de>
In alloc_thread_groups, worker_groups is a pointer to an array,
not an array of pointers.
So
worker_groups[i]
is wrong. It should be
&(*worker_groups)[i]
Found-by: coverity
Fixes: 60aaf93385
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It was being open coded in a few places.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Joern Engel <joern@logfs.org>
Cc: Prasad Joshi <prasadjoshi.linux@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Chris Mason <chris.mason@fusionio.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The new bio_split() can split arbitrary bios - it's not restricted to
single page bios, like the old bio_split() (previously renamed to
bio_pair_split()). It also has different semantics - it doesn't allocate
a struct bio_pair, leaving it up to the caller to handle completions.
Then convert the existing bio_pair_split() users to the new bio_split()
- and also nvme, which was open coding bio splitting.
(We have to take that BUG_ON() out of bio_integrity_trim() because this
bio_split() needs to use it, and there's no reason it has to be used on
bios marked as cloned; BIO_CLONED doesn't seem to have clearly
documented semantics anyways.)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Neil Brown <neilb@suse.de>
This is prep work for introducing a more general bio_split().
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Sage Weil <sage@inktank.com>
This adds a generic mechanism for chaining bio completions. This is
going to be used for a bio_split() replacement, and it turns out to be
very useful in a fair amount of driver code - a fair number of drivers
were implementing this in their own roundabout ways, often painfully.
Note that this means it's no longer to call bio_endio() more than once
on the same bio! This can cause problems for drivers that save/restore
bi_end_io. Arguably they shouldn't be saving/restoring bi_end_io at all
- in all but the simplest cases they'd be better off just cloning the
bio, and immutable biovecs is making bio cloning cheaper. But for now,
we add a bio_endio_nodec() for these cases.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Now that drivers have been converted to the new bvec_iter primitives,
there's no need to trim the bvec before we submit it; and we can't trim
it once we start sharing bvecs.
It used to be that passing a partially completed bio (i.e. one with
nonzero bi_idx) to generic_make_request() was a dangerous thing -
various drivers would choke on such things. But with immutable biovecs
and our new bio splitting that shares the biovecs, submitting partially
completed bios has to work (and should work, now that all the drivers
have been completed to the new primitives)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
We need to convert the dm code to the new bvec_iter primitives which
respect bi_bvec_done; they also allow us to drastically simplify dm's
bio splitting code.
Also, it's no longer necessary to save/restore the bvec array anymore -
driver conversions for immutable bvecs are done, so drivers should never
be modifying it.
Also kill bio_sector_offset(), dm was the only user and it doesn't make
much sense anymore.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
bio_clone() just got more expensive - however, most users of bio_clone()
don't actually need to modify the biovec. If they aren't modifying the
biovec, and they can guarantee that the original bio isn't freed before
the clone (also true in most cases), we can just point the clone at the
original bio's biovec.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Now that we've got a mechanism for immutable biovecs -
bi_iter.bi_bvec_done - we need to convert drivers to use primitives that
respect it instead of using the bvec array directly.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
When we start sharing biovecs, keeping bi_vcnt accurate for splits is
going to be error prone - and unnecessary, if we refactor some code.
So bio_segments() has to go - but most of the existing users just needed
to know if the bio had multiple segments, which is easier - add a
bio_multiple_segments() for them.
(Two of the current uses of bio_segments() are going to go away in a
couple patches, but the current implementation of bio_segments() is
unsafe as soon as we start doing driver conversions for immutable
biovecs - so implement a dumb version for bisectability, it'll go away
in a couple patches)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
More prep work for immutable biovecs - with immutable bvecs drivers
won't be able to use the biovec directly, they'll need to use helpers
that take into account bio->bi_iter.bi_bvec_done.
This updates callers for the new usage without changing the
implementation yet.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Quoc-Son Anh <quoc-sonx.anh@intel.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jan Kara <jack@suse.cz>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
Cc: cbe-oss-dev@lists.ozlabs.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: linux-fsdevel@vger.kernel.org
Cc: cluster-devel@redhat.com
Cc: linux-mm@kvack.org
Acked-by: Geoff Levand <geoff@infradead.org>
For immutable biovecs, we'll be introducing a new bio_iovec() that uses
our new bvec iterator to construct a biovec, taking into account
bvec_iter->bi_bvec_done - this patch updates existing users for the new
usage.
Some of the existing users really do need a pointer into the bvec array
- those uses are all going to be removed, but we'll need the
functionality from immutable to remove them - so for now rename the
existing bio_iovec() -> __bio_iovec(), and it'll be removed in a couple
patches.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
This patch doesn't itself have any functional changes, but immutable
biovecs are going to add a bi_bvec_done member to bi_iter, which will
need to be saved too here.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Bcache has a hack to avoid cloning the biovec if it's all full pages -
but with immutable biovecs coming this won't be necessary anymore.
For now, we remove the special case and always clone the bvec array so
that the immutable biovec patches are simpler.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
It was being open coded in a few places.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Joern Engel <joern@logfs.org>
Cc: Prasad Joshi <prasadjoshi.linux@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Chris Mason <chris.mason@fusionio.com>
Acked-by: NeilBrown <neilb@suse.de>
Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io
during resync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8RCg
-----END PGP SIGNATURE-----
Merge tag 'md/3.13' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io during
resync"
* tag 'md/3.13' of git://neil.brown.name/md:
md/raid5: Use conf->device_lock protect changing of multi-thread resources.
md/raid5: Before freeing old multi-thread worker, it should flush them.
md/raid5: For stripe with R5_ReadNoMerge, we replace REQ_FLUSH with REQ_NOMERGE.
UAPI: include <asm/byteorder.h> in linux/raid/md_p.h
raid1: Rewrite the implementation of iobarrier.
raid1: Add some macros to make code clearly.
raid1: Replace raise_barrier/lower_barrier with freeze_array/unfreeze_array when reconfiguring the array.
raid1: Add a field array_frozen to indicate whether raid in freeze state.
md: Convert use of typedef ctl_table to struct ctl_table
md/raid5: avoid deadlock when raid5 array has unack badblocks during md_stop_writes.
md: use MD_RECOVERY_INTR instead of kthread_should_stop in resync thread.
md: fix some places where mddev_lock return value is not checked.
raid5: Retry R5_ReadNoMerge flag when hit a read error.
raid5: relieve lock contention in get_active_stripe()
raid5: relieve lock contention in get_active_stripe()
wait: add wait_event_cmd()
md/raid5.c: add proper locking to error path of raid5_start_reshape.
md: fix calculation of stacking limits on level change.
raid5: Use slow_path to release stripe when mddev->thread is null
For R5_ReadNoMerge,it mean this bio can't merge with other bios or
request.It used REQ_FLUSH to achieve this. But REQ_NOMERGE can do the
same work.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There is an iobarrier in raid1 because of contention between normal IO and
resync IO. It suspends all normal IO when resync/recovery happens.
However if normal IO is out side the resync window, there is no contention.
So this patch changes the barrier mechanism to only block IO that
could contend with the resync that is currently happening.
We partition the whole space into five parts.
|---------|-----------|------------|----------------|-------|
start next_resync start_next_window end_window
start + RESYNC_WINDOW = next_resync
next_resync + NEXT_NORMALIO_DISTANCE = start_next_window
start_next_window + NEXT_NORMALIO_DISTANCE = end_window
Firstly we introduce some concepts:
1 - RESYNC_WINDOW: For resync, there are 32 resync requests at most at the
same time. A sync request is RESYNC_BLOCK_SIZE(64*1024).
So the RESYNC_WINDOW is 32 * RESYNC_BLOCK_SIZE, that is 2MB.
2 - NEXT_NORMALIO_DISTANCE: the distance between next_resync
and start_next_window. It also indicates the distance between
start_next_window and end_window.
It is currently 3 * RESYNC_WINDOW_SIZE but could be tuned if
this turned out not to be optimal.
3 - next_resync: the next sector at which we will do sync IO.
4 - start: a position which is at most RESYNC_WINDOW before
next_resync.
5 - start_next_window: a position which is NEXT_NORMALIO_DISTANCE
beyond next_resync. Normal-io after this position doesn't need to
wait for resync-io to complete.
6 - end_window: a position which is 2 * NEXT_NORMALIO_DISTANCE beyond
next_resync. This also doesn't need to wait, but is counted
differently.
7 - current_window_requests: the count of normalIO between
start_next_window and end_window.
8 - next_window_requests: the count of normalIO after end_window.
NormalIO will be partitioned into four types:
NormIO1: the end sector of bio is smaller or equal the start
NormIO2: the start sector of bio larger or equal to end_window
NormIO3: the start sector of bio larger or equal to
start_next_window.
NormIO4: the location between start_next_window and end_window
|--------|-----------|--------------------|----------------|-------------|
| start | next_resync | start_next_window | end_window |
NormIO1 NormIO4 NormIO4 NormIO3 NormIO2
For NormIO1, we don't need any io barrier.
For NormIO4, we used a similar approach to the original iobarrier
mechanism. The normalIO and resyncIO must be kept separate.
For NormIO2/3, we add two fields to struct r1conf: "current_window_requests"
and "next_window_requests". They indicate the count of active
requests in the two window.
For these, we don't wait for resync io to complete.
For resync action, if there are NormIO4s, we must wait for it.
If not, we can proceed.
But if resync action reaches start_next_window and
current_window_requests > 0 (that is there are NormIO3s), we must
wait until the current_window_requests becomes zero.
When current_window_requests becomes zero, start_next_window also
moves forward. Then current_window_requests will replaced by
next_window_requests.
There is a problem which when and how to change from NormIO2 to
NormIO3. Only then can sync action progress.
We add a field in struct r1conf "start_next_window".
A: if start_next_window == MaxSector, it means there are no NormIO2/3.
So start_next_window = next_resync + NEXT_NORMALIO_DISTANCE
B: if current_window_requests == 0 && next_window_requests != 0, it
means start_next_window move to end_window
There is another problem which how to differentiate between
old NormIO2(now it is NormIO3) and NormIO2.
For example, there are many bios which are NormIO2 and a bio which is
NormIO3. NormIO3 firstly completed, so the bios of NormIO2 became NormIO3.
We add a field in struct r1bio "start_next_window".
This is used to record the position conf->start_next_window when the call
to wait_barrier() is made in make_request().
In allow_barrier(), we check the conf->start_next_window.
If r1bio->stat_next_window == conf->start_next_window, it means
there is no transition between NormIO2 and NormIO3.
If r1bio->start_next_window != conf->start_next_window, it mean
there was a transition between NormIO2 and NormIO3. There can only
have been one transition. So it only means the bio is old NormIO2.
For one bio, there may be many r1bio's. So we make sure
all the r1bio->start_next_window are the same value.
If we met blocked_dev in make_request(), it must call allow_barrier
and wait_barrier. So the former and the later value of
conf->start_next_window will be change.
If there are many r1bio's with differnet start_next_window,
for the relevant bio, it depend on the last value of r1bio.
It will cause error. To avoid this, we must wait for previous r1bios
to complete.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In a subsequent patch, we'll use some const parameters.
Using macros will make the code clearly.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We used to use raise_barrier to suspend normal IO while we reconfigure
the array. However raise_barrier will soon only suspend some normal
IO, not all. So we need something else.
Change it to use freeze_array.
But freeze_array not only suspends normal io, it also suspends
resync io.
For the place where call raise_barrier for reconfigure, it isn't a
problem.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because the following patch will rewrite the content between normal IO
and resync IO. So we used a parameter to indicate whether raid is in freeze
array.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When raid5 recovery hits a fresh badblock, this badblock will flagged as unack
badblock until md_update_sb() is called.
But md_stop will take reconfig lock which means raid5d can't call
md_update_sb() in md_check_recovery(), the badblock will always
be unack, so raid5d thread enters an infinite loop and md_stop_write()
can never stop sync_thread. This causes deadlock.
To solve this, when STOP_ARRAY ioctl is issued and sync_thread is
running, we need set md->recovery FROZEN and INTR flags and wait for
sync_thread to stop before we (re)take reconfig lock.
This requires that raid5 reshape_request notices MD_RECOVERY_INTR
(which it probably should have noticed anyway) and stops waiting for a
metadata update in that case.
Reported-by: Jianpeng Ma <majianpeng@gmail.com>
Reported-by: Bian Yu <bianyu@kedacom.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We currently use kthread_should_stop() in various places in the
sync/reshape code to abort early.
However some places set MD_RECOVERY_INTR but don't immediately call
md_reap_sync_thread() (and we will shortly get another one).
When this happens we are relying on md_check_recovery() to reap the
thread and that only happen when it finishes normally.
So MD_RECOVERY_INTR must lead to a normal finish without the
kthread_should_stop() test.
So replace all relevant tests, and be more careful when the thread is
interrupted not to acknowledge that latest step in a reshape as it may
not be fully committed yet.
Also add a test on MD_RECOVERY_INTR in the 'is_mddev_idle' loop
so we don't wait have to wait for the speed to drop before we can abort.
Signed-off-by: NeilBrown <neilb@suse.de>
Sometimes we need to lock and mddev and cannot cope with
failure due to interrupt.
In these cases we should use mutex_lock, not mutex_lock_interruptible.
Signed-off-by: NeilBrown <neilb@suse.de>
Because of block layer merge, one bio fails will cause other bios
which belongs to the same request fails, so raid5_end_read_request
will record all these bios as badblocks.
If retry request with R5_ReadNoMerge flag to avoid bios merge,
badblocks can only record sector which is bad exactly.
test:
hdparm --yes-i-know-what-i-am-doing --make-bad-sector 300000 /dev/sdb
mdadm -C /dev/md0 -l5 -n3 /dev/sd[bcd] --assume-clean
mdadm /dev/md0 -f /dev/sdd
mdadm /dev/md0 -r /dev/sdd
mdadm --zero-superblock /dev/sdd
mdadm /dev/md0 -a /dev/sdd
1. Without this patch:
cat /sys/block/md0/md/rd*/bad_blocks
299776 256
299776 256
2. With this patch:
cat /sys/block/md0/md/rd*/bad_blocks
300000 8
300000 8
Signed-off-by: Bian Yu <bianyu@kedacom.com>
Signed-off-by: NeilBrown <neilb@suse.de>
track empty inactive list count, so md_raid5_congested() can use it to make
decision.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The dm-delay target uses a shared workqueue for multiple instances. This
can cause deadlock if two or more dm-delay targets are stacked on the top
of each other.
This patch changes dm-delay to use a per-instance workqueue.
Cc: stable@vger.kernel.org # 2.6.22+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Pull second round of block driver updates from Jens Axboe:
"As mentioned in the original pull request, the bcache bits were pulled
because of their dependency on the immutable bio vecs. Kent re-did
this part and resubmitted it, so here's the 2nd round of (mostly)
driver updates for 3.13. It contains:
- The bcache work from Kent.
- Conversion of virtio-blk to blk-mq. This removes the bio and request
path, and substitutes with the blk-mq path instead. The end result
almost 200 deleted lines. Patch is acked by Asias and Christoph, who
both did a bunch of testing.
- A removal of bootmem.h include from Grygorii Strashko, part of a
larger series of his killing the dependency on that header file.
- Removal of __cpuinit from blk-mq from Paul Gortmaker"
* 'for-linus' of git://git.kernel.dk/linux-block: (56 commits)
virtio_blk: blk-mq support
blk-mq: remove newly added instances of __cpuinit
bcache: defensively handle format strings
bcache: Bypass torture test
bcache: Delete some slower inline asm
bcache: Use ida for bcache block dev minor
bcache: Fix sysfs splat on shutdown with flash only devs
bcache: Better full stripe scanning
bcache: Have btree_split() insert into parent directly
bcache: Move spinlock into struct time_stats
bcache: Kill sequential_merge option
bcache: Kill bch_next_recurse_key()
bcache: Avoid deadlocking in garbage collection
bcache: Incremental gc
bcache: Add make_btree_freeing_key()
bcache: Add btree_node_write_sync()
bcache: PRECEDING_KEY()
bcache: bch_(btree|extent)_ptr_invalid()
bcache: Don't bother with bucket refcount for btree node allocations
bcache: Debug code improvements
...
Make this useful helper available for other users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_active_stripe() is the last place we have lock contention. It has two
paths. One is stripe isn't found and new stripe is allocated, the other is
stripe is found.
The first path basically calls __find_stripe and init_stripe. It accesses
conf->generation, conf->previous_raid_disks, conf->raid_disks,
conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded,
conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except
stripe_hashtbl and inactive_list, other fields are changed very rarely.
With this patch, we split inactive_list and add new hash locks. Each free
stripe belongs to a specific inactive list. Which inactive list is determined
by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a
lock_hash assigned. Stripe's inactive list is protected by a hash lock, which
is determined by it's lock_hash too. The lock_hash is derivied from current
stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned
to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl
list too. The goal of the new hash locks introduced is we can only use the new
locks in the first path of get_active_stripe(). Since we have several hash
locks, lock contention is relieved significantly.
The first path of get_active_stripe() accesses other fields, since they are
changed rarely, changing them now need take conf->device_lock and all hash
locks. For a slow path, this isn't a problem.
If we need lock device_lock and hash lock, we always lock hash lock first. The
tricky part is release_stripe and friends. We need take device_lock first.
Neil's suggestion is we put inactive stripes to a temporary list and readd it
to inactive_list after device_lock is released. In this way, we add stripes to
temporary list with device_lock hold and remove stripes from the list with hash
lock hold. So we don't allow concurrent access to the temporary list, which
means we need allocate temporary list for all participants of release_stripe.
One downside is free stripes are maintained in their inactive list, they can't
across between the lists. By default, we have total 256 stripes and 8 lists, so
each list will have 32 stripes. It's possible one list has free stripe but
other list hasn't. The chance should be rare because stripes allocation are
even distributed. And we can always allocate more stripes for cache, several
mega bytes memory isn't a big deal.
This completely removes the lock contention of the first path of
get_active_stripe(). It slows down the second code path a little bit though
because we now need takes two locks, but since the hash lock isn't contended,
the overhead should be quite small (several atomic instructions). The second
path of get_active_stripe() (basically sequential write or big request size
randwrite) still has lock contentions.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If raid5_start_reshape errors out, we need to reset all the fields
that were updated (not just some), and need to use the seq_counter
to ensure make_request() doesn't use an inconsitent state.
Signed-off-by: NeilBrown <neilb@suse.de>
The various ->run routines of md personalities assume that the 'queue'
has been initialised by the blk_set_stacking_limits() call in
md_alloc().
However when the level is changed (by level_store()) the ->run routine
for the new level is called for an array which has already had the
stacking limits modified. This can result in incorrect final
settings.
So call blk_set_stacking_limits() before ->run in level_store().
A specific consequence of this bug is that it causes
discard_granularity to be set incorrectly when reshaping a RAID4 to a
RAID0.
This is suitable for any -stable kernel since 3.3 in which
blk_set_stacking_limits() was introduced.
Cc: stable@vger.kernel.org (3.3+)
Reported-and-tested-by: "Baldysiak, Pawel" <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When release_stripe() is called in grow_one_stripe(), the
mddev->thread is null. So it will omit one wakeup this thread to
release stripe.
For this condition, use slow_path to release stripe.
Bug was introduced in 3.12
Cc: stable@vger.kernel.org (3.12+)
Fixes: 773ca82fa1
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Improve reliability of buffer allocations for dm messages with a small
number of arguments, a couple path group initialization fixes for dm
multipath, a fix for resizing a dm array, various fixes and
optimizations for dm cache, a fix for device mapper's Kconfig menu
indentation.
Features added include:
- dm crypt support for activating legacy CBC TrueCrypt containers
(useful for forensics of these old TCRYPT containers)
- reduced dm-cache memory requirements for each block in the cache
- basic support for shrinking a dm-cache's cache (fast) device
- most notably, dm-cache support for managing cache coherency when
deploying dm-cache with sophisticated origin volumes (that support
hardware snapshots and/or clustering): these changes come in the form
of a new passthrough operation mode and a cache block invalidation
interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSgt+QAAoJEMUj8QotnQNapcEIALC6U1rmw08PRMSanqg4/aVu
pTahzPtai9jXchQV6q5XsglJryrhD9MoNqrZgHd2drdnmEKTKfVX+/iCXGiE4hQ5
I5QUZf5myEXSd60pCgZwNam+VHMuAuSPQW6LWqRTJjDLHixGF+AoHZGxkEsYgj6M
p686OOpga1nmT2w072xLIh9z2tsv/tm+UN7GSbyklM+/1ItcXxq+/J8rsuth7IqT
k0I60jexq+Q3OaYuJY7vxhdE7PhBCw1fGmtuCcjekqsSVpAdCgDz3FFOEZmyXcUs
YLFE3GcclYQpIPjNjVGTLDFHdoIMWdKiibs/ScBUtegqxWvqP7c87YFhbL+VHDM=
=lLxo
-----END PGP SIGNATURE-----
Merge tag 'dm-3.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper changes from Mike Snitzer:
"A set of device-mapper changes for 3.13.
Improve reliability of buffer allocations for dm messages with a small
number of arguments, a couple path group initialization fixes for dm
multipath, a fix for resizing a dm array, various fixes and
optimizations for dm cache, a fix for device mapper's Kconfig menu
indentation.
Features added include:
- dm crypt support for activating legacy CBC TrueCrypt containers
(useful for forensics of these old TCRYPT containers)
- reduced dm-cache memory requirements for each block in the cache
- basic support for shrinking a dm-cache's cache (fast) device
- most notably, dm-cache support for managing cache coherency when
deploying dm-cache with sophisticated origin volumes (that support
hardware snapshots and/or clustering): these changes come in the
form of a new passthrough operation mode and a cache block
invalidation interface"
* tag 'dm-3.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (32 commits)
dm cache: resolve small nits and improve Documentation
dm cache: add cache block invalidation support
dm cache: add remove_cblock method to policy interface
dm cache policy mq: reduce memory requirements
dm cache metadata: check the metadata version when reading the superblock
dm cache: add passthrough mode
dm cache: cache shrinking support
dm cache: promotion optimisation for writes
dm cache: be much more aggressive about promoting writes to discarded blocks
dm cache policy mq: implement writeback_work() and mq_{set,clear}_dirty()
dm cache: optimize commit_if_needed
dm space map disk: optimise sm_disk_dec_block
MAINTAINERS: add reference to device-mapper's linux-dm.git tree
dm: fix Kconfig menu indentation
dm: allow remove to be deferred
dm table: print error on preresume failure
dm crypt: add TCW IV mode for old CBC TCRYPT containers
dm crypt: properly handle extra key string in initialization
dm cache: log error message if dm_kcopyd_copy() fails
dm cache: use cell_defer() boolean argument consistently
...
Pull block IO core updates from Jens Axboe:
"This is the pull request for the core changes in the block layer for
3.13. It contains:
- The new blk-mq request interface.
This is a new and more scalable queueing model that marries the
best part of the request based interface we currently have (which
is fully featured, but scales poorly) and the bio based "interface"
which the new drivers for high IOPS devices end up using because
it's much faster than the request based one.
The bio interface has no block layer support, since it taps into
the stack much earlier. This means that drivers end up having to
implement a lot of functionality on their own, like tagging,
timeout handling, requeue, etc. The blk-mq interface provides all
these. Some drivers even provide a switch to select bio or rq and
has code to handle both, since things like merging only works in
the rq model and hence is faster for some workloads. This is a
huge mess. Conversion of these drivers nets us a substantial code
reduction. Initial results on converting SCSI to this model even
shows an 8x improvement on single queue devices. So while the
model was intended to work on the newer multiqueue devices, it has
substantial improvements for "classic" hardware as well. This code
has gone through extensive testing and development, it's now ready
to go. A pull request is coming to convert virtio-blk to this
model will be will be coming as well, with more drivers scheduled
for 3.14 conversion.
- Two blktrace fixes from Jan and Chen Gang.
- A plug merge fix from Alireza Haghdoost.
- Conversion of __get_cpu_var() from Christoph Lameter.
- Fix for sector_div() with 64-bit divider from Geert Uytterhoeven.
- A fix for a race between request completion and the timeout
handling from Jeff Moyer. This is what caused the merge conflict
with blk-mq/core, in case you are looking at that.
- A dm stacking fix from Mike Snitzer.
- A code consolidation fix and duplicated code removal from Kent
Overstreet.
- A handful of block bug fixes from Mikulas Patocka, fixing a loop
crash and memory corruption on blk cg.
- Elevator switch bug fix from Tomoki Sekiyama.
A heads-up that I had to rebase this branch. Initially the immutable
bio_vecs had been queued up for inclusion, but a week later, it became
clear that it wasn't fully cooked yet. So the decision was made to
pull this out and postpone it until 3.14. It was a straight forward
rebase, just pruning out the immutable series and the later fixes of
problems with it. The rest of the patches applied directly and no
further changes were made"
* 'for-3.13/core' of git://git.kernel.dk/linux-block: (31 commits)
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: Do not call sector_div() with a 64-bit divisor
kernel: trace: blktrace: remove redundent memcpy() in compat_blk_trace_setup()
block: Consolidate duplicated bio_trim() implementations
block: Use rw_copy_check_uvector()
block: Enable sysfs nomerge control for I/O requests in the plug list
block: properly stack underlying max_segment_size to DM device
elevator: acquire q->sysfs_lock in elevator_change()
elevator: Fix a race in elevator switching and md device initialization
block: Replace __get_cpu_var uses
bdi: test bdi_init failure
block: fix a probe argument to blk_register_region
loop: fix crash if blk_alloc_queue fails
blk-core: Fix memory corruption if blkcg_init_queue fails
block: fix race between request completion and timeout handling
blktrace: Send BLK_TN_PROCESS events to all running traces
blk-mq: don't disallow request merges for req->special being set
blk-mq: mq plug list breakage
blk-mq: fix for flush deadlock
...
Document passthrough mode, cache shrinking, and cache invalidation.
Also, use strcasecmp() and hlist_unhashed().
Reported-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cache block invalidation is removing an entry from the cache without
writing it back. Cache blocks can be invalidated via the
'invalidate_cblocks' message, which takes an arbitrary number of cblock
ranges:
invalidate_cblocks [<cblock>|<cblock begin>-<cblock end>]*
E.g.
dmsetup message my_cache 0 invalidate_cblocks 2345 3456-4567 5678-6789
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Implement policy_remove_cblock() and add remove_cblock method to the mq
policy. These methods will be used by the following cache block
invalidation patch which adds the 'invalidate_cblocks' message to the
cache core.
Also, update some comments in dm-cache-policy.h
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rather than storing the cblock in each cache entry, we allocate all
entries in an array and infer the cblock from the entry position.
Saves 4 bytes of memory per cache block. In addition, this gives us an
easy way of looking up cache entries by cblock.
We no longer need to keep an explicit bitset to track which cblocks
have been allocated. And no searching is needed to find free cblocks.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Need to check the version to verify on-disk metadata is supported.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
"Passthrough" is a dm-cache operating mode (like writethrough or
writeback) which is intended to be used when the cache contents are not
known to be coherent with the origin device. It behaves as follows:
* All reads are served from the origin device (all reads miss the cache)
* All writes are forwarded to the origin device; additionally, write
hits cause cache block invalidates
This mode decouples cache coherency checks from cache device creation,
largely to avoid having to perform coherency checks while booting. Boot
scripts can create cache devices in passthrough mode and put them into
service (mount cached filesystems, for example) without having to worry
about coherency. Coherency that exists is maintained, although the
cache will gradually cool as writes take place.
Later, applications can perform coherency checks, the nature of which
will depend on the type of the underlying storage. If coherency can be
verified, the cache device can be transitioned to writethrough or
writeback mode while still warm; otherwise, the cache contents can be
discarded prior to transitioning to the desired operating mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Morgan Mears <Morgan.Mears@netapp.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Allow a cache to shrink if the blocks being removed from the cache are
not dirty.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Just to be safe, call the error reporting function with "%s" to avoid
any possible future format string leak.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Never saw a profile of bset_search_tree() where it wasn't bottlenecked
on memory until I got my new Haswell machine, but when I tried it there
it was suddenly burning 20% of the cpu in the inner loop on shrd...
Turns out, the version of shrd that takes 64 bit operands has a 9 cycle
latency. hah.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The flow control in btree_insert_node() was... fragile... before,
this'll use more stack (but since our btrees are never more than depth
1, that shouldn't matter) and it should be significantly clearer and
less fragile.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Big garbage collection rewrite; now, garbage collection uses the same
mechanisms as used elsewhere for inserting/updating btree node pointers,
instead of rewriting interior btree nodes in place.
This makes the code significantly cleaner and less fragile, and means we
can now make garbage collection incremental - it doesn't have to hold a
write lock on the root of the btree for the entire duration of garbage
collection.
This means that there's less of a latency hit for doing garbage
collection, which means we can gc more frequently (and do a better job
of reclaiming from the cache), and we can coalesce across more btree
nodes (improving our space efficiency).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Trying to treat btree pointers and leaf node pointers the same way was a
mistake - going to start being more explicit about the type of
key/pointer we're dealing with. This is the first part of that
refactoring; this patch shouldn't change any actual behaviour.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The bucket refcount (dropped with bkey_put()) is only needed to prevent
the newly allocated bucket from being garbage collected until we've
added a pointer to it somewhere. But for btree node allocations, the
fact that we have btree nodes locked is enough to guard against races
with garbage collection.
Eventually the per bucket refcount is going to be replaced with
something specific to bch_alloc_sectors().
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Couple changes:
* Consolidate bch_check_keys() and bch_check_key_order(), and move the
checks that only check_key_order() could do to bch_btree_iter_next().
* Get rid of CONFIG_BCACHE_EDEBUG - now, all that code is compiled in
when CONFIG_BCACHE_DEBUG is enabled, and there's now a sysfs file to
flip on the EDEBUG checks at runtime.
* Dropped an old not terribly useful check in rw_unlock(), and
refactored/improved a some of the other debug code.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Previously, bch_ptr_bad() could return false when there was a pointer to
a nonexistant device... it only filtered out keys with PTR_CHECK_DEV
pointers.
This behaviour was intended for multiple cache device support; for that,
just because the device for one of the pointers has gone away doesn't
mean we want to filter out the rest of the pointers.
But we don't yet explicitly filter/check individual pointers, so without
that this behaviour was wrong - a corrupt bkey with a bad device pointer
could cause us to deref a bad pointer. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Now, the on disk data structures are in a header that can be exported to
userspace - and having them all centralized is nice too.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
With all the recent refactoring around struct btree op struct search has
gotten rather large.
But we can now easily break it up in a different way - we break out
struct btree_insert_op which is for inserting data into the cache, and
that's now what the copying gc code uses - struct search is now specific
to request.c
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Last of the btree_map() conversions. Main visible effect is
bch_btree_insert() is no longer taking a struct btree_op as an argument
anymore - there's no fancy state machine stuff going on, it's just a
normal function.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
When we convert bch_btree_insert() to bch_btree_map_leaf_nodes(), we
won't be passing struct btree_op to bch_btree_insert() anymore - so we
need a different way of returning whether there was a collision (really,
a replace collision).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This is prep work for converting bch_btree_insert to
bch_btree_map_leaf_nodes() - we have to convert all its arguments to
actual arguments. Bunch of churn, but should be straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
There was some looping in submit_partial_cache_hit() and
submit_partial_cache_hit() that isn't needed anymore - originally, we
wouldn't necessarily process the full hit or miss all at once because
when splitting the bio, we took into account the restrictions of the
device we were sending it to.
But, device bio size restrictions are now handled elsewhere, with a
wrapper around generic_make_request() - so that looping has been
unnecessary for awhile now and we can now do quite a bit of cleanup.
And if we trim the key we're reading from to match the subset we're
actually reading, we don't have to explicitly calculate bi_sector
anymore. Neat.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This is a fairly straightforward conversion, mostly reshuffling -
op->lookup_done goes away, replaced by MAP_DONE/MAP_CONTINUE. And the
code for handling cache hits and misses wasn't really btree code, so it
gets moved to request.c.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
With the new btree_map() functions, we don't need to export the stuff
needed for traversing the btree anymore.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Lots of stuff has been open coding its own btree traversal - which is
generally pretty simple code, but there are a few subtleties.
This adds new new functions, bch_btree_map_nodes() and
bch_btree_map_keys(), which do the traversal for you. Everything that's
open coding btree traversal now (with the exception of garbage
collection) is slowly going to be converted to these two functions;
being able to write other code at a higher level of abstraction is a
big improvement w.r.t. overall code quality.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This simplifies the writeback flow control quite a bit - previously, it
was conceptually two coroutines, refill_dirty() and read_dirty(). This
makes the code quite a bit more straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
We needed a dedicated rescuer workqueue for gc anyways... and gc was
conceptually a dedicated thread, just one that wasn't running all the
time. Switch it to a dedicated thread to make the code a bit more
straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
At one point we did do fancy asynchronous waiting stuff with
bucket_wait, but that's all gone (and bucket_wait is used a lot less
than it used to be). So use the standard primitives.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Slowly working on pruning struct btree_op - the aim is for it to only
contain things that are actually necessary for traversing the btree.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Making things less asynchronous that don't need to be - bch_journal()
only has to block when the journal or journal entry is full, which is
emphatically not a fast path. So make it a normal function that just
returns when it finishes, to make the code and control flow easier to
follow.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Try to improve some of the naming a bit to be more consistent, and also
improve the flow of control in request_write() a bit.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Some refactoring - better to explicitly pass stuff around instead of
having it all in the "big bag of state", struct btree_op. Going to prune
struct btree_op quite a bit over time.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This was the main point of all this refactoring - now,
btree_insert_check_key() won't fail just because the leaf node happened
to be full.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
We'll often end up with a list of adjacent keys to insert -
because bch_data_insert() may have to fragment the data it writes.
Originally, to simplify things and avoid having to deal with corner
cases bch_btree_insert() would pass keys from this list one at a time to
btree_insert_recurse() - mainly because the list of keys might span leaf
nodes, so it was easier this way.
With the btree_insert_node() refactoring, it's now a lot easier to just
pass down the whole list and have btree_insert_recurse() iterate over
leaf nodes until it's done.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The flow of control in the old btree insertion code was rather -
backwards; we'd recurse down the btree (in btree_insert_recurse()), and
then if we needed to split the keys to be inserted into the parent node
would be effectively returned up to btree_insert_recurse(), which would
notice there was more work to do and finish the insertion.
The main problem with this was that the full logic for btree insertion
could only be used by calling btree_insert_recurse; if you'd gotten to a
btree leaf some other way and had a key to insert, if it turned out that
node needed to be split you were SOL.
This inverts the flow of control so btree_insert_node() does _full_
btree insertion, including splitting - and takes a (leaf) btree node to
insert into as a parameter.
This means we can now _correctly_ handle cache misses - for cache
misses, we need to insert a fake "check" key into the btree when we
discover we have a cache miss - while we still have the btree locked.
Previously, if the btree node was full inserting a cache miss would just
fail.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This is prep work for the reworked btree insertion code.
The way we set b->parent is ugly and hacky... the problem is, when
btree_split() or garbage collection splits or rewrites a btree node, the
parent changes for all its (potentially already cached) children.
I may change this later and add some code to look through the btree node
cache and find all our cached child nodes and change the parent pointer
then...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Checking i->seq was redundant, because since ages ago we always
initialize the new bset when advancing b->written
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Originally I got this right... except that the divides didn't use
do_div(), which broke 32 bit kernels. When I went to fix that, I forgot
that the raid stripe size usually isn't a power of two... doh
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The old asynchronous discard code was really a relic from when all the
allocation code was asynchronous - now that allocation runs out of a
dedicated thread there's no point in keeping around all that complicated
machinery.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
bch_keybuf_del() takes a spinlock that can't be taken in interrupt context -
whoops. Fortunately, this code isn't enabled by default (you have to toggle a
sysfs thing).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Dirty data accounting wasn't quite right - firstly, we were adding the key we're
inserting after it could have merged with another dirty key already in the
btree, and secondly we could sometimes pass the wrong offset to
bcache_dev_sectors_dirty_add() for dirty data we were overwriting - which is
important when tracking dirty data by stripe.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
If a write block triggers promotion and covers a whole block we can
avoid a copy.
Introduce dm_{hook,unhook}_bio to simplify saving and restoring bio
fields (bi_private is now used by overwrite). Switch writethrough
support over to using these helpers too.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Previously these promotions only got priority if there were unused cache
blocks. Now we give them priority if there are any clean blocks in the
cache.
The fio_soak_test in the device-mapper-test-suite now gives uniform
performance across subvolumes (~16 seconds).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There are now two multiqueues for in cache blocks. A clean one and a
dirty one.
writeback_work comes from the dirty one. Demotions come from the clean
one.
There are two benefits:
- Performance improvement, since demoting a clean block is a noop.
- The cache cleans itself when io load is light.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Check commit_requested flag _before_ calling
dm_cache_changed_this_transaction() superfluously.
Also, be sure to set last_commit_jiffies _after_ dm_cache_commit()
completes.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Don't waste time spotting blocks that have been allocated and then freed
in the same transaction.
The extra lookup is expensive, and I don't think it really gives us much.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The option DM_LOG_USERSPACE is sub-option of DM_MIRROR, so place it
right after DM_MIRROR. Doing so fixes various other Device mapper
targets/features to be properly nested under "Device mapper support".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch allows the removal of an open device to be deferred until
it is closed. (Previously such a removal attempt would fail.)
The deferred remove functionality is enabled by setting the flag
DM_DEFERRED_REMOVE in the ioctl structure on DM_DEV_REMOVE or
DM_REMOVE_ALL ioctl.
On return from DM_DEV_REMOVE, the flag DM_DEFERRED_REMOVE indicates if
the device was removed immediately or flagged to be removed on close -
if the flag is clear, the device was removed.
On return from DM_DEV_STATUS and other ioctls, the flag
DM_DEFERRED_REMOVE is set if the device is scheduled to be removed on
closure.
A device that is scheduled to be deleted can be revived using the
message "@cancel_deferred_remove". This message clears the
DMF_DEFERRED_REMOVE flag so that the device won't be deleted on close.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If preresume fails it is worth logging an error given that a device is
left suspended due to the failure.
This change was motivated by local preresume error logging that was
added to the cache target ("preresume failed"). Elevating this
target-agnostic context for the where the target-specific error occurred
relative to the DM core's callouts makes sense.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
dm-crypt can already activate TCRYPT (TrueCrypt compatible) containers
in LRW or XTS block encryption mode.
TCRYPT containers prior to version 4.1 use CBC mode with some additional
tweaks, this patch adds support for these containers.
This new mode is implemented using special IV generator named TCW
(TrueCrypt IV with whitening). TCW IV only supports containers that are
encrypted with one cipher (Tested with AES, Twofish, Serpent, CAST5 and
TripleDES).
While this mode is legacy and is known to be vulnerable to some
watermarking attacks (e.g. revealing of hidden disk existence) it can
still be useful to activate old containers without using 3rd party
software or for independent forensic analysis of such containers.
(Both the userspace and kernel code is an independent implementation
based on the format documentation and it completely avoids use of
original source code.)
The TCW IV generator uses two additional keys: Kw (whitening seed, size
is always 16 bytes - TCW_WHITENING_SIZE) and Kiv (IV seed, size is
always the IV size of the selected cipher). These keys are concatenated
at the end of the main encryption key provided in mapping table.
While whitening is completely independent from IV, it is implemented
inside IV generator for simplification.
The whitening value is always 16 bytes long and is calculated per sector
from provided Kw as initial seed, xored with sector number and mixed
with CRC32 algorithm. Resulting value is xored with ciphertext sector
content.
IV is calculated from the provided Kiv as initial IV seed and xored with
sector number.
Detailed calculation can be found in the Truecrypt documentation for
version < 4.1 and will also be described on dm-crypt site, see:
http://code.google.com/p/cryptsetup/wiki/DMCrypt
The experimental support for activation of these containers is already
present in git devel brach of cryptsetup.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some encryption modes use extra keys (e.g. loopAES has IV seed) which
are not used in block cipher initialization but are part of key string
in table constructor.
This patch adds an additional field which describes the length of the
extra key(s) and substracts it before real key encryption setting.
The key_size always includes the size, in bytes, of the key provided
in mapping table.
The key_parts describes how many parts (usually keys) are contained in
the whole key buffer. And key_extra_size contains size in bytes of
additional keys part (this number of bytes must be subtracted because it
is processed by the IV generator).
| K1 | K2 | .... | K64 | Kiv |
|----------- key_size ----------------- |
| |-key_extra_size-|
| [64 keys] | [1 key] | => key_parts = 65
Example where key string contains main key K, whitening key
Kw and IV seed Kiv:
| K | Kiv | Kw |
|--------------- key_size --------------|
| |-----key_extra_size------|
| [1 key] | [1 key] | [1 key] | => key_parts = 3
Because key_extra_size is calculated during IV mode setting, key
initialization is moved after this step.
For now, this change has no effect to supported modes (thanks to ilog2
rounding) but it is required by the following patch.
Also, fix a sparse warning in crypt_iv_lmk_one().
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A migration failure should be logged (albeit limited).
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix a few cell_defer() calls that weren't passing a bool.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Return -EINVAL when the specified cache policy is unknown rather than
returning -ENOMEM.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rename takeout_queue to concat_queue.
Fix a harmless bug in mq policies pop() function. Currently pop()
always succeeds, with up coming changes this wont be the case.
Fix typo in comment above pre_cache_to_cache prototype.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Make the quiescing flag an atomic_t and stop protecting it with a spin
lock.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The code that was trying to do this was inadequate. The postsuspend
method (in ioctl context), needs to wait for the worker thread to
acknowledge the request to quiesce. Otherwise the migration count may
drop to zero temporarily before the worker thread realises we're
quiescing. In this case the target will be taken down, but the worker
thread may have issued a new migration, which will cause an oops when
it completes.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
Previously only origin bios could trigger ticks, which meant if all
the io was destined for the cache no ticks were generated. If no ticks
are generated then multiple hits, and movements in general, are
attributed to the same tick.
Only a stop gap fix, we need a better solution.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It is safe to use a mutex in mq_residency() at this point since it is
only called from ioctl context. But future-proof mq_residency() by
using might_sleep() to catch new contexts that cannot sleep.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Someone cut and pasted md's md_trim_bio() into xen-blkfront.c. Come on,
we should know better than this.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they all
get slowly migrated over to the safe versions of the attribute groups
(removing userspace races with the creation of the sysfs files.) Also
in here are some kobject updates, devres expansions, and the first round
of Tejun's sysfs reworking to enable it to be used by other subsystems
as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xAMACgkQMUfUDdst+yk1kQCfcHXhfnrvFZ5J/mDP509IzhNS
ddEAoLEWoivtBppNsgrWqXpD1vi4UMsE
=JmVW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they
all get slowly migrated over to the safe versions of the attribute
groups (removing userspace races with the creation of the sysfs
files.) Also in here are some kobject updates, devres expansions, and
the first round of Tejun's sysfs reworking to enable it to be used by
other subsystems as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (83 commits)
sysfs: rename sysfs_assoc_lock and explain what it's about
sysfs: use generic_file_llseek() for sysfs_file_operations
sysfs: return correct error code on unimplemented mmap()
mdio_bus: convert bus code to use dev_groups
device: Make dev_WARN/dev_WARN_ONCE print device as well as driver name
sysfs: separate out dup filename warning into a separate function
sysfs: move sysfs_hash_and_remove() to fs/sysfs/dir.c
sysfs: remove unused sysfs_get_dentry() prototype
sysfs: honor bin_attr.attr.ignore_lockdep
sysfs: merge sysfs_elem_bin_attr into sysfs_elem_attr
devres: restore zeroing behavior of devres_alloc()
sysfs: fix sysfs_write_file for bin file
input: gameport: convert bus code to use dev_groups
input: serio: remove bus usage of dev_attrs
input: serio: use DEVICE_ATTR_RO()
i2o: convert bus code to use dev_groups
memstick: convert bus code to use dev_groups
tifm: convert bus code to use dev_groups
virtio: convert bus code to use dev_groups
ipack: convert bus code to use dev_groups
...
Entries would be lost if the old tail block was partially filled.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
When pg_init is running no I/O can be submitted to the underlying
devices, as the path priority etc might change. When using queue_io for
this, requests will be piling up within multipath as the block I/O
scheduler just sees a _very fast_ device. All of this queued I/O has to
be resubmitted from within multipathing once pg_init is done.
This approach has the problem that it's virtually impossible to
abort I/O when pg_init is running, and we're adding heavy load
to the devices after pg_init since all of the queued I/O needs to be
resubmitted _before_ any requests can be pulled off of the request queue
and normal operation continues.
This patch will requeue the I/O that triggers the pg_init call, and
return 'busy' when pg_init is in progress. With these changes the block
I/O scheduler will stop submitting I/O during pg_init, resulting in a
quicker path switch and less I/O pressure (and memory consumption) after
pg_init.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[patch header edited for clarity and typos by Mike Snitzer]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Whenever multipath_dtr() is happening we must prevent queueing any
further path activation work. Implement this by adding a new
'pg_init_disabled' flag to the multipath structure that denotes future
path activation work should be skipped if it is set. By disabling
pg_init and then re-enabling in flush_multipath_work() we also avoid the
potential for pg_init to be initiated while suspending an mpath device.
Without this patch a race condition exists that may result in a kernel
panic:
1) If after pg_init_done() decrements pg_init_in_progress to 0, a call
to wait_for_pg_init_completion() assumes there are no more pending path
management commands.
2) If pg_init_required is set by pg_init_done(), due to retryable
mode_select errors, then process_queued_ios() will again queue the
path activation work.
3) If free_multipath() completes before activate_path() work is called a
NULL pointer dereference like the following can be seen when
accessing members of the recently destructed multipath:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
RIP: 0010:[<ffffffffa003db1b>] [<ffffffffa003db1b>] activate_path+0x1b/0x30 [dm_multipath]
[<ffffffff81090ac0>] worker_thread+0x170/0x2a0
[<ffffffff81096c80>] ? autoremove_wake_function+0x0/0x40
[switch to disabling pg_init in flush_multipath_work & header edits by Mike Snitzer]
Signed-off-by: Shiva Krishna Merla <shivakrishna.merla@netapp.com>
Reviewed-by: Krishnasamy Somasundaram <somasundaram.krishnasamy@netapp.com>
Tested-by: Speagle Andy <Andy.Speagle@netapp.com>
Acked-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
dm-mpath and dm-thin must process messages even if some device is
suspended, so we allocate argv buffer with GFP_NOIO. These messages have
a small fixed number of arguments.
On the other hand, dm-switch needs to process bulk data using messages
so excessive use of GFP_NOIO could cause trouble.
The patch also lowers the default number of arguments from 64 to 8, so
that there is smaller load on GFP_NOIO allocations.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
SCSI discard will damage discard stripe bio setting, eg, some fields are
changed. If the stripe is reused very soon, we have wrong bios setting. We
remove discard stripe from hash list, so next time the strip will be fully
initialized.
Suitable for backport to 3.7+.
Cc: <stable@vger.kernel.org> (3.7+)
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
SCSI layer will add new payload for discard request. If two bios are merged
to one, the second bio has bi_vcnt 1 which is set in raid5. This will confuse
SCSI and cause oops.
Suitable for backport to 3.7+
Cc: stable@vger.kernel.org (v3.7+)
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Since:
commit 7ceb17e87b
md: Allow devices to be re-added to a read-only array.
spares are activated on a read-only array. In case of raid1 and raid10
personalities it causes that not-in-sync devices are marked in-sync
without checking if recovery has been finished.
If a read-only array is degraded and one of its devices is not in-sync
(because the array has been only partially recovered) recovery will be skipped.
This patch adds checking if recovery has been finished before marking a device
in-sync for raid1 and raid10 personalities. In case of raid5 personality
such condition is already present (at raid5.c:6029).
Bug was introduced in 3.10 and causes data corruption.
Cc: stable@vger.kernel.org
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch fixes a particular type of data corruption that has been
encountered when loading a snapshot's metadata from disk.
When we allocate a new chunk in persistent_prepare, we increment
ps->next_free and we make sure that it doesn't point to a metadata area
by further incrementing it if necessary.
When we load metadata from disk on device activation, ps->next_free is
positioned after the last used data chunk. However, if this last used
data chunk is followed by a metadata area, ps->next_free is positioned
erroneously to the metadata area. A newly-allocated chunk is placed at
the same location as the metadata area, resulting in data or metadata
corruption.
This patch changes the code so that ps->next_free skips the metadata
area when metadata are loaded in function read_exceptions.
The patch also moves a piece of code from persistent_prepare_exception
to a separate function skip_metadata to avoid code duplication.
CVE-2013-4299
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Commit c0f04d88e4 ("bcache: Fix flushes in writeback mode") was fixing
a reported data corruption bug, but it seems some last minute
refactoring or rebasing introduced a null pointer deref.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Reported-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pre-existing sysfs interfaces which take explicit namespace
argument are weird in that they place the optional @ns in front of
@name which is contrary to the established convention. For example,
we end up forcing vast majority of sysfs_get_dirent() users to do
sysfs_get_dirent(parent, NULL, name), which is silly and error-prone
especially as @ns and @name may be interchanged without causing
compilation warning.
This renames sysfs_get_dirent() to sysfs_get_dirent_ns() and swap the
positions of @name and @ns, and sysfs_get_dirent() is now a wrapper
around sysfs_get_dirent_ns(). This makes confusions a lot less
likely.
There are other interfaces which take @ns before @name. They'll be
updated by following patches.
This patch doesn't introduce any functional changes.
v2: EXPORT_SYMBOL_GPL() wasn't updated leading to undefined symbol
error on module builds. Reported by build test robot. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning target
to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps fix
a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but relatively
little memory. To responsibly select a smaller value users should use
the new nr_bios tracepoint info (via commit 75afb352 "block: Add nr_bios
to block_rq_remap tracepoint") to determine the peak number of bios
their workloads create.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMVHAAoJEMUj8QotnQNaOXgIAJS6/XJKMoHfiDJ9M+XD34rZ
Uyr9TEnubX3DKCRBiY23MUcCQn3fx6BjCGv5/c8L4jQFIuLyDi2yatqpwXcbGSJh
G/S/y6u0Axek+ew7TS80OFop4nblW6MoKnoh9/4N55Ofa+1WvKM4ERUGjHGbauyS
TxmLQPToCFPLYRIOZ+imd6hQuIZ1+FFdJFvi7kY9O6Llx2sLD6fWi1iruBd/Da2H
ByMX3biGN45mSpcBzRbSC/FkJ9CRIvT9n82BDPS0o3Tllt8NaVlEDaovB7h4ncc0
bFuT2Z3Q38B9uZ8Lj0bqdGzv3kXMLCkLo6WhWjyUt84hmDPAzRpBwt60jUqWyZs=
=bjVp
-----END PGP SIGNATURE-----
Merge tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning
target to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps
fix a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but
relatively little memory. To responsibly select a smaller value users
should use the new nr_bios tracepoint info (via commit 75afb352
"block: Add nr_bios to block_rq_remap tracepoint") to determine the
peak number of bios their workloads create"
* tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: add reserved_bio_based_ios module parameter
dm: add reserved_rq_based_ios module parameter
dm: lower bio-based mempool reservation
dm thin: do not expose non-zero discard limits if discards disabled
dm mpath: disable WRITE SAME if it fails
dm-snapshot: fix performance degradation due to small hash size
dm snapshot: workaround for a false positive lockdep warning
dm stats: fix possible counter corruption on 32-bit systems
dm mpath: do not fail path on -ENOSPC
In writeback mode, when we get a cache flush we need to make sure we
issue a flush to the backing device.
The code for sending down an extra flush was wrong - by cloning the bio
we were probably getting flags that didn't make sense for a bare flush,
and also the old code was firing for FUA bios, for which we don't need
to send a flush to the backing device.
This was causing data corruption somehow - the mechanism was never
determined, but this patch fixes it for the users that were seeing it.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
btree_sort_fixup() was overly clever, because it was trying to avoid
pulling a key off the btree iterator in more than one place.
This led to a really obscure bug where we'd break early from the loop in
btree_sort_fixup() if the current key overlapped with keys in more than
one older set, and the next key it overlapped with was zero size.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GFP_NOIO means we could be getting called recursively - mca_alloc() ->
mca_data_alloc() - definitely can't use mutex_lock(bucket_lock) then.
Whoops.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bch_journal_meta() was missing the flush to make the journal write
actually go down (instead of waiting up to journal_delay_ms)...
Whoops
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background writeback works by scanning the btree for dirty data and
adding those keys into a fixed size buffer, then for each dirty key in
the keybuf writing it to the backing device.
When read_dirty() finishes and it's time to scan for more dirty data, we
need to wait for the outstanding writeback IO to finish - they still
take up slots in the keybuf (so that foreground writes can check for
them to avoid races) - without that wait, we'll continually rescan when
we'll be able to add at most a key or two to the keybuf, and that takes
locks that starves foreground IO. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix
drivers/md/bcache/btree.c: In function ‘bch_btree_node_read’:
drivers/md/bcache/btree.c:259: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 3 has type ‘size_t’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The journal replay code didn't handle this case, causing it to go into
an infinite loop...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sysfs attributes with unusual characters have crappy failure modes
in Squeeze (udev 164); later versions of udev are unaffected.
This should make these characters more unusual.
Signed-off-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
That switch statement was obviously wrong, leading to some sort of weird
spinning on rare occasion with discards enabled...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow user to change the number of IOs that are reserved by
bio-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_bio_based_ios
The default value is RESERVED_BIO_BASED_IOS (16). The maximum allowed
value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_bio_based_ios() for use by DM targets and core
code. Switch to sizing dm-io's mempool and bioset using DM core's
configurable 'reserved_bio_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios
The default value is RESERVED_REQUEST_BASED_IOS (256). The maximum
allowed value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code. Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Bio-based device mapper processing doesn't need larger mempools (like
request-based DM does), so lower the number of reserved entries for
bio-based operation. 16 was already used for bio-based DM's bioset
but mistakenly wasn't used for it's _io_cache.
Formalize difference between bio-based and request-based defaults by
introducing RESERVED_BIO_BASED_IOS and RESERVED_REQUEST_BASED_IOS.
(based on older code from Mikulas Patocka)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Fix issue where the block layer would stack the discard limits of the
pool's data device even if the "ignore_discard" pool feature was
specified.
The pool and thin device(s) still had discards disabled because the
QUEUE_FLAG_DISCARD request_queue flag wasn't set. But to avoid user
confusion when "ignore_discard" is used: both the pool device and the
thin device(s) have zeroes for all discard limits.
Also, always set discard_zeroes_data_unsupported in targets because they
should never advertise the 'discard_zeroes_data' capability (even if the
pool's data device supports it).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Workaround the SCSI layer's problematic WRITE SAME heuristics by
disabling WRITE SAME in the DM multipath device's queue_limits if an
underlying device disabled it.
The WRITE SAME heuristics, with both the original commit 5db44863b6
("[SCSI] sd: Implement support for WRITE SAME") and the updated commit
66c28f971 ("[SCSI] sd: Update WRITE SAME heuristics"), default to enabling
WRITE SAME(10) even without successfully determining it is supported.
After the first failed WRITE SAME the SCSI layer will disable WRITE SAME
for the device (by setting sdkp->device->no_write_same which results in
'max_write_same_sectors' in device's queue_limits to be set to 0).
When a device is stacked ontop of such a SCSI device any changes to that
SCSI device's queue_limits do not automatically propagate up the stack.
As such, a DM multipath device will not have its WRITE SAME support
disabled. This causes the block layer to continue to issue WRITE SAME
requests to the mpath device which causes paths to fail and (if mpath IO
isn't configured to queue when no paths are available) it will result in
actual IO errors to the upper layers.
This fix doesn't help configurations that have additional devices
stacked ontop of the mpath device (e.g. LVM created linear DM devices
ontop). A proper fix that restacks all the queue_limits from the bottom
of the device stack up will need to be explored if SCSI will continue to
use this model of optimistically allowing op codes and then disabling
them after they fail for the first time.
Before this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: failing WRITE SAME IO with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
device-mapper: multipath: Failing path 8:112.
end_request: I/O error, dev dm-6, sector 4616
dm-6: WRITE SAME failed. Manually zeroing.
end_request: I/O error, dev dm-6, sector 4616
end_request: I/O error, dev dm-6, sector 5640
end_request: I/O error, dev dm-6, sector 6664
end_request: I/O error, dev dm-6, sector 7688
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
end_request: I/O error, dev dm-6, sector 524296
Aborting journal on device dm-6-8.
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
33553920
After this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: WRITE SAME I/O failed with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
0
It should be noted that WRITE SAME support wasn't enabled in DM
multipath until v3.10.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
LVM2, since version 2.02.96, creates origin with zero size, then loads
the snapshot driver and then loads the origin. Consequently, the
snapshot driver sees the origin size zero and sets the hash size to the
lower bound 64. Such small hash table causes performance degradation.
This patch changes it so that the hash size is determined by the size of
snapshot volume, not minimum of origin and snapshot size. It doesn't
make sense to set the snapshot size significantly larger than the origin
size, so we do not need to take origin size into account when
calculating the hash size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The kernel reports a lockdep warning if a snapshot is invalidated because
it runs out of space.
The lockdep warning was triggered by commit 0976dfc1d0
("workqueue: Catch more locking problems with flush_work()") in v3.5.
The warning is false positive. The real cause for the warning is that
the lockdep engine treats different instances of md->lock as a single
lock.
This patch is a workaround - we use flush_workqueue instead of flush_work.
This code path is not performance sensitive (it is called only on
initialization or invalidation), thus it doesn't matter that we flush the
whole workqueue.
The real fix for the problem would be to teach the lockdep engine to treat
different instances of md->lock as separate locks.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.5+
There was a deliberate race condition in dm_stat_for_entry() to avoid the
overhead of disabling and enabling interrupts. The race could result in
some events not being counted on 64-bit architectures.
However, on 32-bit architectures, operations on long long variables are
not atomic, so the race condition could cause the counter to jump by 2^32.
Such jumps could be disruptive, so we need to do proper locking on 32-bit
architectures.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Alasdair G. Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Since ENOSPC is a target-side error, dm-mpath should just pass the error
information to upper layer instead of retrying itself with path failover.
Otherwise it will end up failing all paths down while path checkers find
all paths ok.
ENOSPC can now be returned from SCSI device after commit a9d6ceb8
("[SCSI] return ENOSPC on thin provisioning failure").
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull vfs pile 4 from Al Viro:
"list_lru pile, mostly"
This came out of Andrew's pile, Al ended up doing the merge work so that
Andrew didn't have to.
Additionally, a few fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (42 commits)
super: fix for destroy lrus
list_lru: dynamically adjust node arrays
shrinker: Kill old ->shrink API.
shrinker: convert remaining shrinkers to count/scan API
staging/lustre/libcfs: cleanup linux-mem.h
staging/lustre/ptlrpc: convert to new shrinker API
staging/lustre/obdclass: convert lu_object shrinker to count/scan API
staging/lustre/ldlm: convert to shrinkers to count/scan API
hugepage: convert huge zero page shrinker to new shrinker API
i915: bail out earlier when shrinker cannot acquire mutex
drivers: convert shrinkers to new count/scan API
fs: convert fs shrinkers to new scan/count API
xfs: fix dquot isolation hang
xfs-convert-dquot-cache-lru-to-list_lru-fix
xfs: convert dquot cache lru to list_lru
xfs: rework buffer dispose list tracking
xfs-convert-buftarg-lru-to-generic-code-fix
xfs: convert buftarg LRU to generic code
fs: convert inode and dentry shrinking to be node aware
vmscan: per-node deferred work
...
Convert the driver shrinkers to the new API. Most changes are compile
tested only because I either don't have the hardware or it's staging
stuff.
FWIW, the md and android code is pretty good, but the rest of it makes me
want to claw my eyes out. The amount of broken code I just encountered is
mind boggling. I've added comments explaining what is broken, but I fear
that some of the code would be best dealt with by being dragged behind the
bike shed, burying in mud up to it's neck and then run over repeatedly
with a blunt lawn mower.
Special mention goes to the zcache/zcache2 drivers. They can't co-exist
in the build at the same time, they are under different menu options in
menuconfig, they only show up when you've got the right set of mm
subsystem options configured and so even compile testing is an exercise in
pulling teeth. And that doesn't even take into account the horrible,
broken code...
[glommer@openvz.org: fixes for i915, android lowmem, zcache, bcache]
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Glauber Costa <glommer@openvz.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Rientjes <rientjes@google.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: J. Bruce Fields <bfields@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
device-mapper device. This dm-stats code required the reintroduction of
a div64_u64_rem() helper, but as a separate method that doesn't slow
down div64_u64() -- especially on 32-bit systems.
Allow the error target to replace request-based DM devices
(e.g. multipath) in addition to bio-based DM devices.
Various other small code fixes and improvements to thin-provisioning, DM
cache and the DM ioctl interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJSLyNnAAoJEMUj8QotnQNaXVEIAKA1l43enaGiROBZEZXgAGUY
1JUsnHES4ujyn/jtT39jPTQf9AW/rS4FUCrZiXG2aaNHXo7+7cdVoBHAiWc7mXad
budBSqn47W7WDyFlQarKwsuYFcdLnqdnieRDMXQ1cN5dl4Rx61LclnsylQd4SSS0
lznXkfOTquetDSuEPOuUHJDZufdacw3PpxWbTKGJld40fd7YZfGWQoG0ek1OeqqL
fA30DTlYnkFyhheLCjFcDY6H55Rt7QpBWOUAa2XXLR6GLfk5iFK99autjWk2xTPT
nppRwQrw9VH+HdW0jGLU+LRs1Y3nxwT9OBLWt9wav87Smdg/7jQAjwde9eKbO2k=
=3ooH
-----END PGP SIGNATURE-----
Merge tag 'dm-3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper updates from Mike Snitzer:
"Add the ability to collect I/O statistics on user-defined regions of a
device-mapper device. This dm-stats code required the reintroduction
of a div64_u64_rem() helper, but as a separate method that doesn't
slow down div64_u64() -- especially on 32-bit systems.
Allow the error target to replace request-based DM devices (e.g.
multipath) in addition to bio-based DM devices.
Various other small code fixes and improvements to thin-provisioning,
DM cache and the DM ioctl interface"
* tag 'dm-3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm stripe: silence a couple sparse warnings
dm: add statistics support
dm thin: always return -ENOSPC if no_free_space is set
dm ioctl: cleanup error handling in table_load
dm ioctl: increase granularity of type_lock when loading table
dm ioctl: prevent rename to empty name or uuid
dm thin: set pool read-only if breaking_sharing fails block allocation
dm thin: prefix pool error messages with pool device name
dm: allow error target to replace bio-based and request-based targets
math64: New separate div64_u64_rem helper
dm space map: optimise sm_ll_dec and sm_ll_inc
dm btree: prefetch child nodes when walking tree for a dm_btree_del
dm btree: use pop_frame in dm_btree_del to cleanup code
dm cache: eliminate holes in cache structure
dm cache: fix stacking of geometry limits
dm thin: fix stacking of geometry limits
dm thin: add data block size limits to Documentation
dm cache: add data block size limits to code and Documentation
dm cache: document metadata device is exclussive to a cache
dm: stop using WQ_NON_REENTRANT
Headline item is multithreading for RAID5 so that more
IO/sec can be supported on fast (SSD) devices.
Also TILE-Gx SIMD suppor for RAID6 calculations and an
assortment of bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=zLxh
-----END PGP SIGNATURE-----
Merge tag 'md/3.12' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Headline item is multithreading for RAID5 so that more IO/sec can be
supported on fast (SSD) devices. Also TILE-Gx SIMD suppor for RAID6
calculations and an assortment of bug fixes"
* tag 'md/3.12' of git://neil.brown.name/md:
raid5: only wakeup necessary threads
md/raid5: flush out all pending requests before proceeding with reshape.
md/raid5: use seqcount to protect access to shape in make_request.
raid5: sysfs entry to control worker thread number
raid5: offload stripe handle to workqueue
raid5: fix stripe release order
raid5: make release_stripe lockless
md: avoid deadlock when dirty buffers during md_stop.
md: Don't test all of mddev->flags at once.
md: Fix apparent cut-and-paste error in super_90_validate
raid6/test: replace echo -e with printf
RAID: add tilegx SIMD implementation of raid6
md: fix safe_mode buglet.
md: don't call md_allow_write in get_bitmap_file.
Eliminate the following sparse warnings:
drivers/md/dm-stripe.c:443:12: warning: symbol 'dm_stripe_init' was not declared. Should it be static?
drivers/md/dm-stripe.c:456:6: warning: symbol 'dm_stripe_exit' was not declared. Should it be static?
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support the collection of I/O statistics on user-defined regions of
a DM device. If no regions are defined no statistics are collected so
there isn't any performance impact. Only bio-based DM devices are
currently supported.
Each user-defined region specifies a starting sector, length and step.
Individual statistics will be collected for each step-sized area within
the range specified.
The I/O statistics counters for each step-sized area of a region are
in the same format as /sys/block/*/stat or /proc/diskstats but extra
counters (12 and 13) are provided: total time spent reading and
writing in milliseconds. All these counters may be accessed by sending
the @stats_print message to the appropriate DM device via dmsetup.
The creation of DM statistics will allocate memory via kmalloc or
fallback to using vmalloc space. At most, 1/4 of the overall system
memory may be allocated by DM statistics. The admin can see how much
memory is used by reading
/sys/module/dm_mod/parameters/stats_current_allocated_bytes
See Documentation/device-mapper/statistics.txt for more details.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If pool has 'no_free_space' set it means a previous allocation already
determined the pool has no free space (and failed that allocation with
-ENOSPC). By always returning -ENOSPC if 'no_free_space' is set, we do
not allow the pool to oscillate between allocating blocks and then not.
But a side-effect of this determinism is that if a user wants to be able
to allocate new blocks they'll need to reload the pool's table (to clear
the 'no_free_space' flag). This reload will happen automatically if the
pool's data volume is resized. But if the user takes action to free a
lot of space by deleting snapshot volumes, etc the pool will no longer
allow data allocations to continue without an intervening table reload.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Hold the mapped device's type_lock before calling populate_table() since
it is where the table's type is determined based on the specified
targets. There is no need to allow concurrent table loads to race to
establish the table's targets or type.
This eliminates the need to grab the lock in dm_table_set_type().
Also verify that the type_lock is held in both dm_set_md_type() and
dm_get_md_type().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A device-mapper device must always have a name consisting of a non-empty
string. If the device also has a uuid, this similarly must not be an
empty string.
The DM_DEV_CREATE ioctl enforces these rules when the device is created,
but this patch is needed to enforce them when DM_DEV_RENAME is used to
change the name or uuid.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
break_sharing() now handles an arbitrary alloc_data_block() error
the same way as provision_block(): marks pool read-only and errors the
cell.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Useful to know which pool is experiencing the error.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
It may be useful to switch a request-based table to the "error" target.
Enhance the DM core to allow a hybrid target_type which is capable of
handling either bios (via .map) or requests (via .map_rq).
Add a request-based map function (.map_rq) to the "error" target_type;
making it DM's first hybrid target. Train dm_table_set_type() to prefer
the mapped device's established type (request-based or bio-based). If
the mapped device doesn't have an established type default to making the
table with the hybrid target(s) bio-based.
Tested 'dmsetup wipe_table' to work on both bio-based and request-based
devices.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch set is a set of driver updates (ufs, zfcp, lpfc, mpt2/3sas,
qla4xxx, qla2xxx [adding support for ISP8044 + other things]) we also have a
new driver: esas2r which has a number of static checker problems, but which I
expect to resolve over the -rc course of 3.12 under the new driver exception.
We also have the error return updates that were discussed at LSF.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSJfX5AAoJEDeqqVYsXL0M8u8H+gN65iA4YeNc3Eq9F6mliLfg
JOIfn6GRz7ChbQ1ZZKdH/5xCOtzXphrkg7kRGmr9frsvYZ4X2c7W3xweQTA08gqP
wPH7/xyPffPnUm/r+V+SV41pm39bEjmltknLwiF572a6iOoVYQpnmDjdZQKT0jU0
QZEqI81+646m8edCnApLw3Tlsn2gBwHaDrkd55H2IQGTkOD016C0CQbM+cNMU440
qdqDcfRWCsp1fhLo3JH2kWTx8BihhyfEYAFz4tZwuFdGGkRZxF20HwyzV0h3hZOG
kZ2Gd1BFf0SybxOcESQmAukbcH5hyumX1Y7HMYKZbS2ubD4MCO1MO8UUtLXlxNc=
=PDBQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch set is a set of driver updates (ufs, zfcp, lpfc, mpt2/3sas,
qla4xxx, qla2xxx [adding support for ISP8044 + other things]).
We also have a new driver: esas2r which has a number of static checker
problems, but which I expect to resolve over the -rc course of 3.12
under the new driver exception.
We also have the error return that were discussed at LSF"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (118 commits)
[SCSI] sg: push file descriptor list locking down to per-device locking
[SCSI] sg: checking sdp->detached isn't protected when open
[SCSI] sg: no need sg_open_exclusive_lock
[SCSI] sg: use rwsem to solve race during exclusive open
[SCSI] scsi_debug: fix logical block provisioning support when unmap_alignment != 0
[SCSI] scsi_debug: fix endianness bug in sdebug_build_parts()
[SCSI] qla2xxx: Update the driver version to 8.06.00.08-k.
[SCSI] qla2xxx: print MAC via %pMR.
[SCSI] qla2xxx: Correction to message ids.
[SCSI] qla2xxx: Correctly print out/in mailbox registers.
[SCSI] qla2xxx: Add a new interface to update versions.
[SCSI] qla2xxx: Move queue depth ramp down message to i/o debug level.
[SCSI] qla2xxx: Select link initialization option bits from current operating mode.
[SCSI] qla2xxx: Add loopback IDC-TIME-EXTEND aen handling support.
[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it
[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN
[SCSI] qla2xxx: Correct Interrupt Register offset for ISPFX00
[SCSI] qla2xxx: Remove handling of Shutdown Requested AEN from qlafx00_process_aen().
[SCSI] qla2xxx: Send all AENs for ISPFx00 to above layers.
[SCSI] qla2xxx: Add changes in initialization for ISPFX00 cards with BIOS
...
If there are not enough stripes to handle, we'd better not always
queue all available work_structs. If one worker can only handle small
or even none stripes, it will impact request merge and create lock
contention.
With this patch, the number of work_struct running will depend on
pending stripes number. Note: some statistics info used in the patch
are accessed without locking protection. This should doesn't matter,
we just try best to avoid queue unnecessary work_struct.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some requests - particularly 'discard' and 'read' are handled
differently depending on whether a reshape is active or not.
It is harmless to assume reshape is active if it isn't but wrong
to act as though reshape is not active when it is.
So when we start reshape - after making clear to all requests that
reshape has started - use mddev_suspend/mddev_resume to flush out all
requests. This will ensure that no requests will be assuming the
absence of reshape once it really starts.
Signed-off-by: NeilBrown <neilb@suse.de>
make_request() access various shape parameters (raid_disks, chunk_size
etc) which might be changed by raid5_start_reshape().
If the later is called at and awkward time during the form, the wrong
stripe_head might be used.
So introduce a 'seqcount' and after finding a stripe_head make sure
there is no reason to expect that we got the wrong one.
Signed-off-by: NeilBrown <neilb@suse.de>
Add a sysfs entry to control running workqueue thread number. If
group_thread_cnt is set to 0, we will disable workqueue offload handling of
stripes.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This is another attempt to create multiple threads to handle raid5 stripes.
This time I use workqueue.
raid5 handles request (especially write) in stripe unit. A stripe is page size
aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a
state machine for the corresponding stripe, which includes reading some disks
of the stripe, calculating parity, and writing some disks of the stripe. The
state machine is running in raid5d thread currently. Since there is only one
thread, it doesn't scale well for high speed storage. An obvious solution is
multi-threading.
To get better performance, we have some requirements:
a. locality. stripe corresponding to request submitted from one cpu is better
handled in thread in local cpu or local node. local cpu is preferred but some
times could be a bottleneck, for example, parity calculation is too heavy.
local node running has wide adaptability.
b. configurablity. Different setup of raid5 array might need diffent
configuration. Especially the thread number. More threads don't always mean
better performance because of lock contentions.
My original implementation is creating some kernel threads. There are
interfaces to control which cpu's stripe each thread should handle. And
userspace can set affinity of the threads. This provides biggest flexibility
and configurability. But it's hard to use and apparently a new thread pool
implementation is disfavor.
Recent workqueue improvement is quite promising. unbound workqueue will be
bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to
do affinity setting. For example, we can only include one HT sibling in
affinity. Since work is non-reentrant by default, and we can control running
thread number by limiting dispatched work_struct number.
In this patch, I created several stripe worker group. A group is a numa node.
stripes from cpus of one node will be added to a group list. Workqueue thread
of one node will only handle stripes of worker group of the node. In this way,
stripe handling has numa node locality. And as I said, we can control thread
number by limiting dispatched work_struct number.
The work_struct callback function handles several stripes in one run. A typical
work queue usage is to run one unit in each work_struct. In raid5 case, the
unit is a stripe. But we can't do that:
a. Though handling a stripe doesn't need lock because of reference accounting
and stripe isn't in any list, queuing a work_struct for each stripe will make
workqueue lock contended very heavily.
b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we
might dispatch request. If each work_struct only handles one stripe, such block
plug is meaningless.
This implementation can't do very fine grained configuration. But the numa
binding is most popular usage model, should be enough for most workloads.
Note: since we have only one stripe queue, switching to multi-thread might
decrease request size dispatching down to low level layer. The impact depends
on thread number, raid configuration and workload. So multi-thread raid5 might
not be proper for all setups.
Changes V1 -> V2:
1. remove WQ_NON_REENTRANT
2. disabling multi-threading by default
3. Add more descriptions in changelog
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
patch "make release_stripe lockless" changes the order stripes are released.
Originally I thought block layer can take care of request merge, but it appears
there are still some requests not merged. It's easy to fix the order.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
release_stripe still has big lock contention. We just add the stripe to a llist
without taking device_lock. We let the raid5d thread to do the real stripe
release, which must hold device_lock anyway. In this way, release_stripe
doesn't hold any locks.
The side effect is the released stripes order is changed. But sounds not a big
deal, stripes are never handled in order. And I thought block layer can already
do nice request merge, which means order isn't that important.
I kept the unplug release batch, which is unnecessary with this patch from lock
contention avoid point of view, and actually if we delete it, the stripe_head
release_list and lru can share storage. But the unplug release batch is also
helpful for request merge. We probably can delay wakeup raid5d till unplug, but
I'm still afraid of the case which raid5d is running.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When the last process closes /dev/mdX sync_blockdev will be called so
that all buffers get flushed.
So if it is then opened for the STOP_ARRAY ioctl to be sent there will
be nothing to flush.
However if we open /dev/mdX in order to send the STOP_ARRAY ioctl just
moments before some other process which was writing closes their file
descriptor, then there won't be a 'last close' and the buffers might
not get flushed.
So do_md_stop() calls sync_blockdev(). However at this point it is
holding ->reconfig_mutex. So if the array is currently 'clean' then
the writes from sync_blockdev() will not complete until the array
can be marked dirty and that won't happen until some other thread
can get ->reconfig_mutex. So we deadlock.
We need to move the sync_blockdev() call to before we take
->reconfig_mutex.
However then some other thread could open /dev/mdX and write to it
after we call sync_blockdev() and before we actually stop the array.
This can leave dirty data in the page cache which is awkward.
So introduce new flag MD_STILL_CLOSED. Set it before calling
sync_blockdev(), clear it if anyone does open the file, and abort the
STOP_ARRAY attempt if it gets set before we lock against further
opens.
It is still possible to get problems if you open /dev/mdX, write to
it, then issue the STOP_ARRAY ioctl. Just don't do that.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->flags is mostly used to record if an update of the
metadata is needed. Sometimes the whole field is tested
instead of just the important bits. This makes it difficult
to introduce more state bits.
So replace all bare tests of mddev->flags with tests for the bits
that actually need testing.
Signed-off-by: NeilBrown <neilb@suse.de>
Setting a variable to itself probably wasn't the intention here.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Whe we set the safe_mode_timeout to a smaller value we trigger a timeout
immediately - otherwise the small value might not be honoured.
However if the previous timeout was 0 meaning "no timeout", we didn't.
This would mean that no timeout happens until the next write completes,
which could be a long time.
Signed-off-by: NeilBrown <neilb@suse.de>
There is no really need as GFP_NOIO is very likely sufficient,
and failure is not catastrophic.
Calling md_allow_write here will convert a read-auto array to
read/write which could be confusing when you are just performing
a read operation.
Signed-off-by: NeilBrown <neilb@suse.de>
When a medium error is detected the SCSI stack should return
ENODATA to the upper layers.
[jejb: fix whitespace error]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Prior to this patch these methods did a lookup followed by an insert.
Instead they now call a common mutate function that adjusts the value
according to a callback function. This avoids traversing the data
structures twice and hence improves performance.
Also factor out sm_ll_lookup_big_ref_count() for use by both
sm_ll_lookup() and sm_ll_mutate().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-btree now takes advantage of dm-bufio's ability to prefetch data via
dm_bm_prefetch(). Prior to this change many btree node visits were
causing a synchronous read.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove a visited leaf straight away from the stack, rather than
marking all it's children as visited and letting it get removed on the
next iteration. May also offer a micro optimisation in dm_btree_del.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reorder members in the cache structure to eliminate 6 out of 7 holes
(reclaiming 24 bytes). Also, the 'worker' and 'waker' members no longer
straddle cachelines.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
