Commit graph

33 commits

Author SHA1 Message Date
Andrew Murray
8673e02e58 arm64: perf: Add support for ARMv8.5-PMU 64-bit counters
At present ARMv8 event counters are limited to 32-bits, though by
using the CHAIN event it's possible to combine adjacent counters to
achieve 64-bits. The perf config1:0 bit can be set to use such a
configuration.

With the introduction of ARMv8.5-PMU support, all event counters can
now be used as 64-bit counters.

Let's enable 64-bit event counters where support exists. Unless the
user sets config1:0 we will adjust the counter value such that it
overflows upon 32-bit overflow. This follows the same behaviour as
the cycle counter which has always been (and remains) 64-bits.

Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Mark: fix ID field names, compare with 8.5 value]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
2020-03-17 22:50:30 +00:00
Linus Torvalds
dfd437a257 arm64 updates for 5.3:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
 
 - Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
   manage the permissions of executable vmalloc regions more strictly
 
 - Slight performance improvement by keeping softirqs enabled while
   touching the FPSIMD/SVE state (kernel_neon_begin/end)
 
 - Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new XAFLAG
   and AXFLAG instructions for floating point comparison flags
   manipulation) and FRINT (rounding floating point numbers to integers)
 
 - Re-instate ARM64_PSEUDO_NMI support which was previously marked as
   BROKEN due to some bugs (now fixed)
 
 - Improve parking of stopped CPUs and implement an arm64-specific
   panic_smp_self_stop() to avoid warning on not being able to stop
   secondary CPUs during panic
 
 - perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
   platforms
 
 - perf: DDR performance monitor support for iMX8QXP
 
 - cache_line_size() can now be set from DT or ACPI/PPTT if provided to
   cope with a system cache info not exposed via the CPUID registers
 
 - Avoid warning on hardware cache line size greater than
   ARCH_DMA_MINALIGN if the system is fully coherent
 
 - arm64 do_page_fault() and hugetlb cleanups
 
 - Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
 
 - Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the 'arm_boot_flags'
   introduced in 5.1)
 
 - CONFIG_RANDOMIZE_BASE now enabled in defconfig
 
 - Allow the selection of ARM64_MODULE_PLTS, currently only done via
   RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
   over into the vmalloc area
 
 - Make ZONE_DMA32 configurable
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAl0eHqcACgkQa9axLQDI
 XvFyNA/+L+bnkz8m3ncydlqqfXomQn4eJJVQ8Uksb0knJz+1+3CUxxbO4ry4jXZN
 fMkbggYrDPRKpDbsUl0lsRipj7jW9bqan+N37c3SWqCkgb6HqDaHViwxdx6Ec/Uk
 gHudozDSPh/8c7hxGcSyt/CFyuW6b+8eYIQU5rtIgz8aVY2BypBvS/7YtYCbIkx0
 w4CFleRTK1zXD5mJQhrc6jyDx659sVkrAvdhf6YIymOY8nBTv40vwdNo3beJMYp8
 Po/+0Ixu+VkHUNtmYYZQgP/AGH96xiTcRnUqd172JdtRPpCLqnLqwFokXeVIlUKT
 KZFMDPzK+756Ayn4z4huEePPAOGlHbJje8JVNnFyreKhVVcCotW7YPY/oJR10bnc
 eo7yD+DxABTn+93G2yP436bNVa8qO1UqjOBfInWBtnNFJfANIkZweij/MQ6MjaTA
 o7KtviHnZFClefMPoiI7HDzwL8XSmsBDbeQ04s2Wxku1Y2xUHLx4iLmadwLQ1ZPb
 lZMTZP3N/T1554MoURVA1afCjAwiqU3bt1xDUGjbBVjLfSPBAn/25IacsG9Li9AF
 7Rp1M9VhrfLftjFFkB2HwpbhRASOxaOSx+EI3kzEfCtM2O9I1WHgP3rvCdc3l0HU
 tbK0/IggQicNgz7GSZ8xDlWPwwSadXYGLys+xlMZEYd3pDIOiFc=
 =0TDT
 -----END PGP SIGNATURE-----

Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux

Pull arm64 updates from Catalin Marinas:

 - arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}

 - Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
   manage the permissions of executable vmalloc regions more strictly

 - Slight performance improvement by keeping softirqs enabled while
   touching the FPSIMD/SVE state (kernel_neon_begin/end)

 - Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
   XAFLAG and AXFLAG instructions for floating point comparison flags
   manipulation) and FRINT (rounding floating point numbers to integers)

 - Re-instate ARM64_PSEUDO_NMI support which was previously marked as
   BROKEN due to some bugs (now fixed)

 - Improve parking of stopped CPUs and implement an arm64-specific
   panic_smp_self_stop() to avoid warning on not being able to stop
   secondary CPUs during panic

 - perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
   platforms

 - perf: DDR performance monitor support for iMX8QXP

 - cache_line_size() can now be set from DT or ACPI/PPTT if provided to
   cope with a system cache info not exposed via the CPUID registers

 - Avoid warning on hardware cache line size greater than
   ARCH_DMA_MINALIGN if the system is fully coherent

 - arm64 do_page_fault() and hugetlb cleanups

 - Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)

 - Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
   'arm_boot_flags' introduced in 5.1)

 - CONFIG_RANDOMIZE_BASE now enabled in defconfig

 - Allow the selection of ARM64_MODULE_PLTS, currently only done via
   RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
   over into the vmalloc area

 - Make ZONE_DMA32 configurable

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
  perf: arm_spe: Enable ACPI/Platform automatic module loading
  arm_pmu: acpi: spe: Add initial MADT/SPE probing
  ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
  ACPI/PPTT: Modify node flag detection to find last IDENTICAL
  x86/entry: Simplify _TIF_SYSCALL_EMU handling
  arm64: rename dump_instr as dump_kernel_instr
  arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
  arm64: Implement panic_smp_self_stop()
  arm64: Improve parking of stopped CPUs
  arm64: Expose FRINT capabilities to userspace
  arm64: Expose ARMv8.5 CondM capability to userspace
  arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
  arm64: ARM64_MODULES_PLTS must depend on MODULES
  arm64: bpf: do not allocate executable memory
  arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
  arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
  arm64: module: create module allocations without exec permissions
  arm64: Allow user selection of ARM64_MODULE_PLTS
  acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
  arm64: Allow selecting Pseudo-NMI again
  ...
2019-07-08 09:54:55 -07:00
Jeremy Linton
d24a0c7099 arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI 6.3 adds additional fields to the MADT GICC
structure to describe SPE PPI's. We pick these out
of the cached reference to the madt_gicc structure
similarly to the core PMU code. We then create a platform
device referring to the IRQ and let the user/module loader
decide whether to load the SPE driver.

Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
2019-06-27 16:53:42 +01:00
Thomas Gleixner
d2912cb15b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:55 +02:00
Will Deacon
342e53bd85 arm64: perf: Add support for Armv8.1 PMCEID register format
Armv8.1 allocated the upper 32-bits of the PMCEID registers to describe
the common architectural and microarchitecture events beginning at 0x4000.

Add support for these registers to our probing code, so that we can
advertise the SPE events when they are supported by the CPU.

Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-11-21 13:16:33 +00:00
Will Deacon
ca2b497253 arm64: perf: Reject stand-alone CHAIN events for PMUv3
It doesn't make sense for a perf event to be configured as a CHAIN event
in isolation, so extend the arm_pmu structure with a ->filter_match()
function to allow the backend PMU implementation to reject CHAIN events
early.

Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-10-12 15:25:17 +01:00
Suzuki K Poulose
e2da97d328 arm_pmu: Add support for 64bit event counters
Each PMU has a set of 32bit event counters. But in some
special cases, the events could be counted using counters
which are effectively 64bit wide.

e.g, Arm V8 PMUv3 has a 64 bit cycle counter which can count
only the CPU cycles. Also, the PMU can chain the event counters
to effectively count as a 64bit counter.

Add support for tracking the events that uses 64bit counters.
This only affects the periods set for each counter in the core
driver.

Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-07-10 18:19:02 +01:00
Suzuki K Poulose
3a95200d3f arm_pmu: Change API to support 64bit counter values
Convert the {read/write}_counter APIs to handle 64bit values
to enable supporting chained event counters. The backends still
use 32bit values and we pass them 32bit values only. So in effect
there are no functional changes.

Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-07-10 18:19:02 +01:00
Suzuki K Poulose
8d3e994241 arm_pmu: Clean up maximum period handling
Each PMU defines their max_period of the counter as the maximum
value that can be counted. Since all the PMU backends support
32bit counters by default, let us remove the redundant field.

No functional changes.

Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-07-10 18:19:02 +01:00
Mark Rutland
0788f1e973 arm_pmu: simplify arm_pmu::handle_irq
The arm_pmu::handle_irq() callback has the same prototype as a generic
IRQ handler, taking the IRQ number and a void pointer argument which it
must convert to an arm_pmu pointer.

This means that all arm_pmu::handle_irq() take an IRQ number they never
use, and all must explicitly cast the void pointer to an arm_pmu
pointer.

Instead, let's change arm_pmu::handle_irq to take an arm_pmu pointer,
allowing these casts to be removed. The redundant IRQ number parameter
is also removed.

Suggested-by: Hoeun Ryu <hoeun.ryu@lge.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-05-21 18:07:05 +01:00
Mark Rutland
167e61438d arm_pmu: acpi: request IRQs up-front
We can't request IRQs in atomic context, so for ACPI systems we'll have
to request them up-front, and later associate them with CPUs.

This patch reorganises the arm_pmu code to do so. As we no longer have
the arm_pmu structure at probe time, a number of prototypes need to be
adjusted, requiring changes to the common arm_pmu code and arm_pmu
platform code.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20 11:34:54 +00:00
Mark Rutland
84b4be57ae arm_pmu: note IRQs and PMUs per-cpu
To support ACPI systems, we need to request IRQs before we know the
associated PMU, and thus we need some percpu variable that the IRQ
handler can find the PMU from.

As we're going to request IRQs without the PMU, we can't rely on the
arm_pmu::active_irqs mask, and similarly need to track requested IRQs
with a percpu variable.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: made armpmu_count_irq_users static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20 11:34:54 +00:00
Mark Rutland
0dc1a1851a arm_pmu: add armpmu_alloc_atomic()
In ACPI systems, we don't know the makeup of CPUs until we hotplug them
on, and thus have to allocate the PMU datastructures at hotplug time.
Thus, we must use GFP_ATOMIC allocations.

Let's add an armpmu_alloc_atomic() that we can use in this case.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20 11:34:54 +00:00
Mark Rutland
d3d5aac206 arm_pmu: fold platform helpers into platform code
The armpmu_{request,free}_irqs() helpers are only used by
arm_pmu_platform.c, so let's fold them in and make them static.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20 11:34:53 +00:00
Mark Rutland
c0248c9663 arm_pmu: kill arm_pmu_platdata
Now that we have no platforms passing platform data to the arm_pmu code,
we can get rid of the platdata and associated hooks, paving the way for
rework of our IRQ handling.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20 11:34:53 +00:00
Will Deacon
a3287c41ff drivers/perf: arm_pmu: Request PMU SPIs with IRQF_PER_CPU
Since the PMU register interface is banked per CPU, CPU PMU interrrupts
cannot be handled by a CPU other than the one with the PMU asserting the
interrupt. This means that migrating PMU SPIs, as we do during a CPU
hotplug operation doesn't make any sense and can lead to the IRQ being
disabled entirely if we route a spurious IRQ to the new affinity target.

This has been observed in practice on AMD Seattle, where CPUs on the
non-boot cluster appear to take a spurious PMU IRQ when coming online,
which is routed to CPU0 where it cannot be handled.

This patch passes IRQF_PERCPU for PMU SPIs and forcefully sets their
affinity prior to requesting them, ensuring that they cannot
be migrated during hotplug events. This interacts badly with the DB8500
erratum workaround that ping-pongs the interrupt affinity from the handler,
so we avoid passing IRQF_PERCPU in that case by allowing the IRQ flags
to be overridden in the platdata.

Fixes: 3cf7ee98b8 ("drivers/perf: arm_pmu: move irq request/free into probe")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-07-27 13:43:22 +01:00
Mark Rutland
45736a72fb drivers/perf: arm_pmu: add ACPI framework
This patch adds framework code to handle parsing PMU data out of the
MADT, sanity checking this, and managing the association of CPUs (and
their interrupts) with appropriate logical PMUs.

For the time being, we expect that only one PMU driver (PMUv3) will make
use of this, and we simply pass in a single probe function.

This is based on an earlier patch from Jeremy Linton.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-04-11 16:29:54 +01:00
Mark Rutland
18bfcfe51b drivers/perf: arm_pmu: split out platform device probe logic
Now that we've split the pdev and DT probing logic from the runtime
management, let's move the former into its own file. We gain a few lines
due to the copyright header and includes, but this should keep the logic
clearly separated, and paves the way for adding ACPI support in a
similar fashion.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
[will: rename nr_irqs to avoid conflict with global variable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-04-11 16:29:54 +01:00
Mark Rutland
083c52144a drivers/perf: arm_pmu: define armpmu_init_fn
We expect an ARM PMU's init function to have a particular prototype,
which we open-code in a few places. This is less than ideal, considering
that we cast a void value to this type in one location, and a mismatch
could easily be missed.

Add a typedef so that we can ensure this is consistent.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-04-11 16:29:53 +01:00
Mark Rutland
c09adab01e drivers/perf: arm_pmu: split irq request from enable
For historical reasons, we lazily request and free interrupts in the
arm pmu driver. This requires us to refcount use of the pmu (by way of
counting the active events) in order to request/free interrupts at the
correct times, which complicates the driver somewhat.

The existing logic is flawed, as it only considers currently online CPUs
when requesting, freeing, or managing the affinity of interrupts.
Intervening hotplug events can result in erroneous IRQ affinity, online
CPUs for which interrupts have not been requested, or offline CPUs whose
interrupts are still requested.

To fix this, this patch splits the requesting of interrupts from any
per-cpu management (i.e. per-cpu enable/disable, and configuration of
cpu affinity). We now request all interrupts up-front at probe time (and
never free them, since we never unregister PMUs).

The management of affinity, and per-cpu enable/disable now happens in
our cpu hotplug callback, ensuring it occurs consistently. This means
that we must now invoke the CPU hotplug callback at boot time in order
to configure IRQs, and since the callback also resets the PMU hardware,
we can remove the duplicate reset in the probe path.

This rework renders our event refcounting unnecessary, so this is
removed.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make armpmu_get_cpu_irq static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-03-31 18:20:29 +01:00
Mark Rutland
7ed98e0168 drivers/perf: arm_pmu: manage interrupts per-cpu
When requesting or freeing interrupts, we use platform_get_irq() to find
relevant irqs, backing this up with additional information in an
optional irq_affinity table.

This means that our irq request and free paths are tied to a
platform_device, and our request path must jump through a number of
hoops in order to determine the required affinity of each interrupt.

Given that the affinity must be static, we can compute the affinity once
up-front at probe time, simplifying the irq request and free paths. By
recording interrupts in a per-cpu data structure, we simplify a few
paths, and permit a subsequent rework of the request and free paths.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: rename local nr_irqs variable to avoid conflict with global]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-03-31 18:20:02 +01:00
Linus Torvalds
597f03f9d1 Merge branch 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner:
 "Yet another batch of cpu hotplug core updates and conversions:

   - Provide core infrastructure for multi instance drivers so the
     drivers do not have to keep custom lists.

   - Convert custom lists to the new infrastructure. The block-mq custom
     list conversion comes through the block tree and makes the diffstat
     tip over to more lines removed than added.

   - Handle unbalanced hotplug enable/disable calls more gracefully.

   - Remove the obsolete CPU_STARTING/DYING notifier support.

   - Convert another batch of notifier users.

   The relayfs changes which conflicted with the conversion have been
   shipped to me by Andrew.

   The remaining lot is targeted for 4.10 so that we finally can remove
   the rest of the notifiers"

* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
  cpufreq: Fix up conversion to hotplug state machine
  blk/mq: Reserve hotplug states for block multiqueue
  x86/apic/uv: Convert to hotplug state machine
  s390/mm/pfault: Convert to hotplug state machine
  mips/loongson/smp: Convert to hotplug state machine
  mips/octeon/smp: Convert to hotplug state machine
  fault-injection/cpu: Convert to hotplug state machine
  padata: Convert to hotplug state machine
  cpufreq: Convert to hotplug state machine
  ACPI/processor: Convert to hotplug state machine
  virtio scsi: Convert to hotplug state machine
  oprofile/timer: Convert to hotplug state machine
  block/softirq: Convert to hotplug state machine
  lib/irq_poll: Convert to hotplug state machine
  x86/microcode: Convert to hotplug state machine
  sh/SH-X3 SMP: Convert to hotplug state machine
  ia64/mca: Convert to hotplug state machine
  ARM/OMAP/wakeupgen: Convert to hotplug state machine
  ARM/shmobile: Convert to hotplug state machine
  arm64/FP/SIMD: Convert to hotplug state machine
  ...
2016-10-03 19:43:08 -07:00
Jeremy Linton
85023b2e13 arm64: pmu: Hoist pmu platform device name
Move the PMU name into a common header file so it may
be referenced by other users.

Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-16 17:11:34 +01:00
Mark Rutland
48538b5863 drivers/perf: arm_pmu: expose a cpumask in sysfs
In systems with heterogeneous CPUs, there are multiple logical CPU PMUs,
each of which covers a subset of CPUs in the system. In some cases
userspace needs to know which CPUs a given logical PMU covers, so we'd
like to expose a cpumask under sysfs, similar to what is done for uncore
PMUs.

Unfortunately, prior to commit 00e727bb38 ("perf stat: Balance
opening and reading events"), perf stat only correctly handled a cpumask
holding a single CPU, and only when profiling in system-wide mode. In
other cases, the presence of a cpumask file could cause perf stat to
behave erratically.

Thus, exposing a cpumask file would break older perf binaries in cases
where they would otherwise work.

To avoid this issue while still providing userspace with the information
it needs, this patch exposes a differently-named file (cpus) under
sysfs. New tools can look for this and operate correctly, while older
tools will not be adversely affected by its presence.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-09 14:51:51 +01:00
Mark Rutland
86cdd72af9 drivers/perf: arm_pmu: add common attr group fields
In preparation for adding common attribute groups, add an array of
attribute group pointers to arm_pmu, which will be used if the
backend hasn't already set pmu::attr_groups.

Subsequent patches will move backends over to using these, before adding
common fields.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-09 14:51:51 +01:00
Sebastian Andrzej Siewior
6e103c0cfe arm/perf: Use multi instance instead of custom list
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160817171420.sdwk2qivxunzryz4@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-09-02 20:05:06 +02:00
Sebastian Andrzej Siewior
37b502f121 arm/perf: Fix hotplug state machine conversion
Mark Rutland pointed out that this commit is incomplete:

  7d88eb695a ("arm/perf: Convert to hotplug state machine")

The problem is that:

 > We may have multiple PMUs (e.g. two in big.LITTLE systems), and
 > __oprofile_cpu_pmu only contains one of these. So this conversion is not
 > correct.
 >
 > We were relying on the notifier list implicitly containing a list of
 > those PMUs. It seems like we need an explicit list here.
 >
 > We keep __oprofile_cpu_pmu around for legacy 32-bit users of OProfile
 > (on non-hetereogeneous systems), and that's all that the variable should
 > be used for.

Introduce arm_pmu_list to correctly handle multiple PMUs in the system.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-tip-commits@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160719111733.GA22911@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-07-20 09:57:34 +02:00
Thomas Gleixner
7d88eb695a arm/perf: Convert to hotplug state machine
Straight forward conversion w/o bells and whistles.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153335.794097159@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-07-15 10:40:23 +02:00
Ashok Kumar
4b1a9e6934 arm64/perf: Filter common events based on PMCEIDn_EL0
The complete common architectural and micro-architectural
event number structure is filtered based on PMCEIDn_EL0 and
exposed to /sys using is_visibile function pointer in events
attribute_group.
To filter the events in is_visible function, pmceid based bitmap
is stored in arm_pmu structure and the id field from
perf_pmu_events_attr is used to check against the bitmap.

The function which derives event bitmap from PMCEIDn_EL0 is
executed in the cpus, which has the pmu being initialized,
for heterogeneous pmu support.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ashok Kumar <ashoks@broadcom.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-04-25 14:11:10 +01:00
Lorenzo Pieralisi
da4e4f18af drivers/perf: arm_pmu: implement CPU_PM notifier
When a CPU is suspended (either through suspend-to-RAM or CPUidle),
its PMU registers content can be lost, which means that counters
registers values that were initialized on power down entry have to be
reprogrammed on power-up to make sure the counters set-up is preserved
(ie on power-up registers take the reset values on Cold or Warm reset,
which can be architecturally UNKNOWN).

To guarantee seamless profiling conditions across a core power down
this patch adds a CPU PM notifier to ARM pmus, that upon CPU PM
entry/exit from low-power states saves/restores the pmu registers
set-up (by using the ARM perf API), so that the power-down/up cycle does
not affect the perf behaviour (apart from a black-out period between
power-up/down CPU PM notifications that is unavoidable).

Cc: Will Deacon <will.deacon@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-02-26 14:37:06 +00:00
Martin Fuzzey
8d1a0ae724 ARM: perf: Set ARMv7 SDER SUNIDEN bit
ARMv7 counters other than the CPU cycle counter only work if the Secure
Debug Enable Register (SDER) SUNIDEN bit is set.

Since access to the SDER is only possible in secure state, it will
only be done if the device tree property "secure-reg-access" is set.

Without this:

 Performance counter stats for 'sleep 1':

          14606094 cycles                    #    0.000 GHz
                 0 instructions              #    0.00  insns per cycle

After applying:

 Performance counter stats for 'sleep 1':

           5843809 cycles
           2566484 instructions              #    0.44  insns per cycle

       1.020144000 seconds time elapsed

Some platforms (eg i.MX53) may also need additional platform specific
setup.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
[will: add warning if property is found on arm64]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-01-25 18:37:44 +00:00
Mark Rutland
b916b785af drivers/perf: kill armpmu_register
Nothing outside of drivers/perf/arm_pmu.c should call armpmu_register
any more, so it no longer needs to be in include/linux/perf/arm_pmu.h.
Additionally, by folding it in to arm_pmu_device_probe we can allow
drivers to override struct pmu fields without getting blatted by the
armpmu code.

This patch folds armpmu_register into arm_pmu_device_probe. The logging
to the console is moved to after the PMU is successfully registered with
the core perf code.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Will Deacon <will.deacon@arm.com>
Cc: Drew Richardson <drew.richardson@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-11-16 15:41:49 +00:00
Mark Rutland
fa8ad7889d arm: perf: factor arm_pmu core out to drivers
To enable sharing of the arm_pmu code with arm64, this patch factors it
out to drivers/perf/. A new drivers/perf directory is added for
performance monitor drivers to live under.

MAINTAINERS is updated accordingly. Files added previously without a
corresponsing MAINTAINERS update (perf_regs.c, perf_callchain.c, and
perf_event.h) are also added.

Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: augmented Kconfig help slightly]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-07-31 15:01:14 +01:00