An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When polling for link status, don't consider ports which have a forced
link. Such ports don't monitor their phy or may not even have a phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell switches allow the RGMII Rx and Tx clock to be delayed
when the port is using RGMII. Have the adjust_link function look at
the phy interface type and enable this delay as requested.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be useful for DSA and CPU ports to have a phy-mode property, in
particular to specify RGMII delays. Parse the property and set it in
the fixed-link phydev.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, DSA and CPU ports are configured to the maximum speed the
switch supports. However there can be use cases where the peer devices
port is slower. Allow a fixed-link property to be used with the DSA
and CPU port in the device tree, and use this information to configure
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the supported field of the phydev to indicate the speed features
of the phy. If the phy is never attached to a netdev, but used in an
adjust_link() function, the speed will be incorrectly evaluated to
10/half rather than the correct speed/duplex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code sets user ports to perform auto negotiation using the
phy. CPU and DSA ports are configured to full duplex and maximum speed
the switch supports.
There are however use cases where the CPU has a slower port, and when
user ports have SFP modules with fixed speed. In these cases, port
settings to be read from a fixed_phy devices. The switch driver then
needs to implement the adjust_link op, so the port settings can be
set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet MAC drivers using the PHY library require the hardcoding
of link parameters when interfaced to a switch device, SFP module,
switch to switch port, etc. This has typically lead to various ad-hoc
implementations looking like this:
- using a "fixed PHY" emulated device, which will provide link
indication towards the Ethernet MAC driver and hardware
- pretend there is no PHY and hardcode link parameters, ala mv643x_eth
Based on that, it is desireable to have the PHY drivers advertise the
correct link parameters, just like regular Ethernet PHYs towards their
CPU Ethernet MAC drivers, however, Ethernet MAC drivers should be able
to tell whether this link should be monitored or not. In the context
of an Ethernet switch, SFP module, switch to switch link, we do not
need to monitor this link since it should be always up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak in the mpls netns init function in case of failure. If
register_net_sysctl fails then we need to free the ctl_table.
Fixes: 7720c01f3f ("mpls: Add a sysctl to control the size of the mpls label table")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TOS is another key aspect of the lookup passed to fib_validate_source.
Add it to the tracepoint.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix build errors:
kernel/built-in.o: In function `bpf_trace_printk':
bpf_trace.c:(.text+0x11a254): undefined reference to `strncpy_from_unsafe'
kernel/built-in.o: In function `fetch_memory_string':
trace_kprobe.c:(.text+0x11acf8): undefined reference to `strncpy_from_unsafe'
move strncpy_from_unsafe() next to probe_kernel_read/write()
which use the same memory access style.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 1a6877b9c0 ("lib: introduce strncpy_from_unsafe()")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
tcp: receive-side per route dctcp handling
Original cover letter:
Currently, the following case doesn't use DCTCP, even if it should:
- responder has f.e. cubic as system wide default
- 'ip route congctl dctcp $src' was set
Then, DCTCP is NOT used if a DCTCP sender attempts to connect from a
host in the $src range: ECT(0) is set, but listen_sk is not dctcp, so
we fail the INET_ECN_is_not_ect sanity check.
We also have to examine the dst used for the SYN/ACK reply to make
this case work.
In order to minimize additional cost, store the 'ecn is must have'
information is the dst_features field.
The set targets -next instead of -net since this doesn't seem to be a
serious bug and to give the change more soak time until it hits linus
tree.
v1 -> v2:
- Addressed Dave's feedback, not exposing any bits to user space
- Added patch 3 to reject incorrect configurations
- Rest as is, rebased and retested
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the following case doesn't use DCTCP, even if it should:
A responder has f.e. Cubic as system wide default, but for a specific
route to the initiating host, DCTCP is being set in RTAX_CC_ALGO. The
initiating host then uses DCTCP as congestion control, but since the
initiator sets ECT(0), tcp_ecn_create_request() doesn't set ecn_ok,
and we have to fall back to Reno after 3WHS completes.
We were thinking on how to solve this in a minimal, non-intrusive
way without bloating tcp_ecn_create_request() needlessly: lets cache
the CA ecn option flag in RTAX_FEATURES. In other words, when ECT(0)
is set on the SYN packet, set ecn_ok=1 iff route RTAX_FEATURES
contains the unexposed (internal-only) DST_FEATURE_ECN_CA. This allows
to only do a single metric feature lookup inside tcp_ecn_create_request().
Joint work with Florian Westphal.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Feature bits that are invalid should not be accepted by the kernel,
only the lower 4 bits may be configured, but not the remaining ones.
Even from these 4, 2 of them are unused.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the identation a bit, there's no need to artificically have
it increased.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_create_info() is already quite large, so before adding more
code to the metrics section move that to a helper, similar to
ip6_convert_metrics.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the addition of a new sysctl variable which controls the
generation of IGMP reports for link local multicast groups in the
224.0.0.X range.
IGMP reports for local multicast groups can now be optionally
inhibited by setting the value to zero e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero.
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tun-info options pointer is used in few cases to
pass options around. But tunnel options can be accessed using
ip_tunnel_info_opts() API without using the pointer. Following
patch removes the redundant pointer and consistently make use
of API.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/af_inet.c: In function 'snmp_get_cpu_field64':
>> net/ipv4/af_inet.c:1486:26: error: 'offt' undeclared (first use in this function)
v = *(((u64 *)bhptr) + offt);
^
net/ipv4/af_inet.c:1486:26: note: each undeclared identifier is reported only once for each function it appears in
net/ipv4/af_inet.c: In function 'snmp_fold_field64':
>> net/ipv4/af_inet.c:1499:39: error: 'offct' undeclared (first use in this function)
res += snmp_get_cpu_field(mib, cpu, offct, syncp_offset);
^
>> net/ipv4/af_inet.c:1499:10: error: too many arguments to function 'snmp_get_cpu_field'
res += snmp_get_cpu_field(mib, cpu, offct, syncp_offset);
^
net/ipv4/af_inet.c:1455:5: note: declared here
u64 snmp_get_cpu_field(void __percpu *mib, int cpu, int offt)
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Poll() returns immediately after setting the kernel current frame
(ring->head) to SKIP from user space even though there is no new
frame. And in a case of all frames is VALID, user space program
unintensionally sets (only) kernel current frame to UNUSED, then
calls poll(), it will not return immediately even though there are
VALID frames.
To avoid situations like above, I think we need to scan all frames
to find VALID frames at poll() like netlink_alloc_skb(),
netlink_forward_ring() finding an UNUSED frame at skb allocation.
Signed-off-by: Ken-ichirou MATSUZAWA <chamas@h4.dion.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksey Makarov says:
====================
net: thunderx: New features and fixes
v2:
- The unused affinity_mask field of the structure cmp_queue
has been deleted. (thanks to David Miller)
- The unneeded initializers have been dropped. (thanks to Alexey Klimov)
- The commit message "net: thunderx: Rework interrupt handling"
has been fixed. (thanks to Alexey Klimov)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting VF's corresponding BGX LMAC in internal
loopback mode. This mode can be used for verifying basic HW
functionality such as packet I/O, RX checksum validation,
CQ/RBDR interrupts, stats e.t.c. Useful when DUT has no external
network connectivity.
'loopback' mode can be enabled or disabled via ethtool.
Note: This feature is not supported when no of VFs enabled are
morethan no of physical interfaces i.e active BGX LMACs
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for handling multiple qsets assigned to a
single VF. There by increasing no of queues from earlier 8 to max
no of CPUs in the system i.e 48 queues on a single node and 96 on
dual node system. User doesn't have option to assign which Qsets/VFs
to be merged. Upon request from VF, PF assigns next free Qsets as
secondary qsets. To maintain current behavior no of queues is kept
to 8 by default which can be increased via ethtool.
If user wants to unbind NICVF driver from a secondary Qset then it
should be done after tearing down primary VF's interface.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework interrupt handler to avoid checking IRQ affinity of
CQ interrupts. Now separate handlers are registered for each IRQ
including RBDR. Register interrupt handlers for only those
which are being used. Add nicvf_dump_intr_status() and use it
in irq handlers.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures HW to strip 802.1Q header if found in a
receiving packet. The stripped VLAN ID and TCI information is
passed on to software via CQE_RX. Also sets netdev's 'vlan_features'
so that other HW offload features can be used for tagged packets.
This offload feature can be enabled or disabled via ethtool.
Network stack normally ignores RPS for 802.1Q packets and hence low
throughput. With this offload enabled throughput for tagged packets
will be almost same as normal packets.
Note: This patch doesn't enable HW VLAN insertion for transmit packets.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for receive hashing HW offload by using RSS_ALG
and RSS_TAG fields of CQE_RX descriptor. Also removed dependency
on minimum receive queue count to configure RSS so that hash is
always generated.
This hash is used by RPS logic to distribute flows across multiple
CPUs. Offload can be disabled via ethtool.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the nicvf_send_msg_to_pf() function in the mailbox code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added ethtool support to dump receive packet error statistics reported
in CQE. Also made some small fixes
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The liquidio and thunder drivers have different maintainers.
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghavendra K T says:
====================
Optimize the snmp stat aggregation for large cpus
While creating 1000 containers, perf is showing lot of time spent in
snmp_fold_field on a large cpu system.
The current patch tries to improve by reordering the statistics gathering.
Please note that similar overhead was also reported while creating
veth pairs https://lkml.org/lkml/2013/3/19/556
Changes in V4:
- remove 'item' variable and use IPSTATS_MIB_MAX to avoid sparse
warning (Eric) also remove 'item' parameter (Joe)
- add missing memset of padding.
Changes in V3:
- use memset to initialize temp buffer in leaf function. (David)
- use memcpy to copy the buffer data to stat instead of unalign_pu (Joe)
- Move buffer definition to leaf function __snmp6_fill_stats64() (Eric)
-
Changes in V2:
- Allocate the stat calculation buffer in stack. (Eric)
Setup:
160 cpu (20 core) baremetal powerpc system with 1TB memory
1000 docker containers was created with command
docker run -itd ubuntu:15.04 /bin/bash in loop
observation:
Docker container creation linearly increased from around 1.6 sec to 7.5 sec
(at 1000 containers) perf data showed, creating veth interfaces resulting in
the below code path was taking more time.
rtnl_fill_ifinfo
-> inet6_fill_link_af
-> inet6_fill_ifla6_attrs
-> snmp_fold_field
proposed idea:
currently __snmp6_fill_stats64 calls snmp_fold_field that walks
through per cpu data to of an item (iteratively for around 36 items).
The patch tries to aggregate the statistics by going through
all the items of each cpu sequentially which is reducing cache
misses.
Performance of docker creation improved by around more than 2x
after the patch.
before the patch:
================
3f45ba571a42e925c4ec4aaee0e48d7610a9ed82a4c931f83324d41822cf6617
real 0m6.836s
user 0m0.095s
sys 0m0.011s
perf record -a docker run -itd ubuntu:15.04 /bin/bash
=======================================================
50.73% docker [kernel.kallsyms] [k] snmp_fold_field
9.07% swapper [kernel.kallsyms] [k] snooze_loop
3.49% docker [kernel.kallsyms] [k] veth_stats_one
2.85% swapper [kernel.kallsyms] [k] _raw_spin_lock
1.37% docker docker [.] backtrace_qsort
1.31% docker docker [.] strings.FieldsFunc
cache-misses: 2.7%
after the patch:
=============
9178273e9df399c8290b6c196e4aef9273be2876225f63b14a60cf97eacfafb5
real 0m3.249s
user 0m0.088s
sys 0m0.020s
perf record -a docker run -itd ubuntu:15.04 /bin/bash
=======================================================
10.57% docker docker [.] scanblock
8.37% swapper [kernel.kallsyms] [k] snooze_loop
6.91% docker [kernel.kallsyms] [k] snmp_get_cpu_field
6.67% docker [kernel.kallsyms] [k] veth_stats_one
3.96% docker docker [.] runtime_MSpan_Sweep
2.47% docker docker [.] strings.FieldsFunc
cache-misses: 1.41 %
Please let me know if you have suggestions/comments.
Thanks Eric, Joe and David for the comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Docker container creation linearly increased from around 1.6 sec to 7.5 sec
(at 1000 containers) and perf data showed 50% ovehead in snmp_fold_field.
reason: currently __snmp6_fill_stats64 calls snmp_fold_field that walks
through per cpu data of an item (iteratively for around 36 items).
idea: This patch tries to aggregate the statistics by going through
all the items of each cpu sequentially which is reducing cache
misses.
Docker creation got faster by more than 2x after the patch.
Result:
Before After
Docker creation time 6.836s 3.25s
cache miss 2.7% 1.41%
perf before:
50.73% docker [kernel.kallsyms] [k] snmp_fold_field
9.07% swapper [kernel.kallsyms] [k] snooze_loop
3.49% docker [kernel.kallsyms] [k] veth_stats_one
2.85% swapper [kernel.kallsyms] [k] _raw_spin_lock
perf after:
10.57% docker docker [.] scanblock
8.37% swapper [kernel.kallsyms] [k] snooze_loop
6.91% docker [kernel.kallsyms] [k] snmp_get_cpu_field
6.67% docker [kernel.kallsyms] [k] veth_stats_one
changes/ideas suggested:
Using buffer in stack (Eric), Usage of memset (David), Using memcpy in
place of unaligned_put (Joe).
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
openvswitch: Cleanup post vport conversion.
After converting all vport to netdev implmentations there
is no need for some of vport functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all vport types are now backed by netdev, we can directly
use netdev stats. Following patch removes redundant stat
from vport.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tun info is passed using skb-dst pointer. Now we have
converted all vports to netdev based implementation so
Now we can remove redundant pointer to tun-info from OVS_CB.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused get_name() function pointer from vport ops.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geneve can benefit from GRO at the device level in a manner similar
to other tunnels, especially as hardware offloads are still emerging.
After this patch, aggregated frames are seen on the tunnel interface.
Single stream throughput nearly doubles in ideal circumstances (on
old hardware).
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error occurs skipping IPv6 extension headers retain the already
parsed IP protocol and IPv6 addresses in the flow. Also assume that the
packet is not a fragment in the absence of information to the contrary;
that is always use the frag_off value set by ipv6_skip_exthdr().
This allows matching on the IP protocol and IPv6 addresses of packets
with malformed extension headers.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-08-28
One more bunch of Bluetooth patches for 4.3:
- Crash fix for hci_bcm driver
- Enhancements to hci_intel driver (e.g. baudrate configuration)
- Fix for SCO link type after multiple connect attempts
- Cleanups & minor fixes in a few other places
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler may not be available when smsc911x probes if the
interrupt handler is a GPIO controller for example. Let's fix that
by adding handling for -EPROBE_DEFER.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
tunnels: fix incorrect IPv4/v6 headers interpretation
With tunneling, it is currently possible to get an IPv6 header and interpret
it as an IPv4 header, or to interpret an IPv6 address as an IPv4 address
(and vice versa). This leads to things like sending packets to incorrect
address, IPv6 flow label being interpreted as IP packet length, etc.
Fix several places where this can happen.
Most of this is net-next only. The third patch affects net, too, but it
doesn't seem there's anything in user space that sets the attribute at all
currently, thus net-next is fine.
Changelog:
v2: fixed geneve after incorrect rebase on top of Pravin's patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By default (subject to the sysctl settings), IPv6 sockets listen also for
IPv4 traffic. Vxlan is not prepared for that and expects IPv6 header in
packets received through an IPv6 socket.
In addition, it's currently not possible to have both IPv4 and IPv6 vxlan
tunnel on the same port (unless bindv6only sysctl is enabled), as it's not
possible to create and bind both IPv4 and IPv6 vxlan interfaces and there's
no way to specify both IPv4 and IPv6 remote/group IP addresses.
Set IPV6_V6ONLY on vxlan sockets to fix both of these issues. This is not
done globally in udp_tunnel, as l2tp and tipc seems to work okay when
receiving IPv4 packets on IPv6 socket and people may rely on this behavior.
The other tunnels (geneve and fou) do not support IPv6.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fou does not really support IPv6 encapsulation. After an UDP socket is
created in fou_create, the encap_rcv callback is set either to fou_udp_recv
or to gue_udp_recv. Both of those unconditionally assume that the received
packet has an IPv4 header and access the data at network_header as it was an
IPv4 header. This leads to IPv6 flow label being interpreted as IP packet
length, etc.
Disallow fou tunnel to be configured as IPv6 until real IPv6 support is
added to fou.
CC: Tom Herbert <tom@herbertland.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few useful tracepoints developing VRF driver.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing an non-primary transport during ASCONF
processing, we end up traversing the transport list
twice: once in sctp_cmd_del_non_primary, and once in
sctp_assoc_del_peer. We can avoid the second
search and call sctp_assoc_rm_peer() instead.
Found by code inspection during code reviews.
Signed-off-by: Vladislav Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
