This reverts commit 8cb8e6f168.
That commit introduced a regression with the Bluetooth Profile Tuning
Suite(PTS), Reverting this make sure that L2CAP is in a qualificable
state.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As we don't have any error control on the Streaming mode, i.e., we don't
need to keep a copy of the skb for later resending we don't need to
call skb_clone() on it.
Then we can go one further here, and dequeue the skb before sending it,
that also means we don't need to look to sk->sk_send_head anymore.
The patch saves memory and time when sending Streaming mode data, so
it is good to mainline.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When receiving L2CAP negative configuration response with respect
to MTU parameter we modify wrong field. MTU here means proposed
value of MTU that the remote device intends to transmit. So for local
L2CAP socket it is pi->imtu.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This fixes a bug which caused the FCS setting to show L2CAP_FCS_CRC16
with L2CAP modes other than ERTM or streaming. At present, this only
affects the FCS value shown with getsockopt() for basic mode.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
tcp: Fix >4GB writes on 64-bit.
net/9p: Mount only matching virtio channels
de2104x: fix ethtool
tproxy: check for transparent flag in ip_route_newports
ipv6: add IPv6 to neighbour table overflow warning
tcp: fix TSO FACK loss marking in tcp_mark_head_lost
3c59x: fix regression from patch "Add ethtool WOL support"
ipv6: add a missing unregister_pernet_subsys call
s390: use free_netdev(netdev) instead of kfree()
sgiseeq: use free_netdev(netdev) instead of kfree()
rionet: use free_netdev(netdev) instead of kfree()
ibm_newemac: use free_netdev(netdev) instead of kfree()
smsc911x: Add MODULE_ALIAS()
net: reset skb queue mapping when rx'ing over tunnel
br2684: fix scheduling while atomic
de2104x: fix TP link detection
de2104x: fix power management
de2104x: disable autonegotiation on broken hardware
net: fix a lockdep splat
e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
...
Fixes kernel bugzilla #16603
tcp_sendmsg() truncates iov_len to an 'int' which a 4GB write to write
zero bytes, for example.
There is also the problem higher up of how verify_iovec() works. It
wants to prevent the total length from looking like an error return
value.
However it does this using 'int', but syscalls return 'long' (and
thus signed 64-bit on 64-bit machines). So it could trigger
false-positives on 64-bit as written. So fix it to use 'long'.
Reported-by: Olaf Bonorden <bono@onlinehome.de>
Reported-by: Daniel Büse <dbuese@gmx.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
p9_virtio_create will only compare the the channel's tag characters
against the device name till the end of the channel's tag but not till
the end of the device name. This means that if a user defines channels
with the tags foo and foobar then he would mount foo when he requested
foonot and may mount foo when he requested foobar.
Thus it is necessary to check both string lengths against each other in
case of a successful partial string match.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 and IPv6 have separate neighbour tables, so
the warning messages should be distinguishable.
[ Add a suitable message prefix on the ipv4 side as well -DaveM ]
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP uses FACK algorithm to mark lost packets in
tcp_mark_head_lost(), if the number of packets in the (TSO) skb is
greater than the number of packets that should be marked lost, TCP
incorrectly exits the loop and marks no packets lost in the skb. This
underestimates tp->lost_out and affects the recovery/retransmission.
This patch fargments the skb and marks the correct amount of packets
lost.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -ENOMEM when erroring on kmalloc and fix memory leaks when returning on error.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Clean up a missing exit path in the ipv6 module init routines. In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure. But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations. This patch cleans up both the failed load path and
the unload path. Tested by myself with good results.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/net/addrconf.h | 1 +
net/ipv6/addrconf.c | 11 ++++++++---
net/ipv6/addrlabel.c | 5 +++++
3 files changed, 14 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
You can't call atomic_notifier_chain_unregister() while in atomic context.
Fix, call un/register_atmdevice_notifier in module __init and __exit.
Bug report:
http://comments.gmane.org/gmane.linux.network/172603
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have for each socket :
One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)
Possible scenarios are :
(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...
(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)
This (C) case conflicts with (A) :
CPU1 [A] CPU2 [C]
read_lock(callback_lock)
<BH> spin_lock_bh(slock)
<wait to spin_lock(slock)>
<wait to write_lock_bh(callback_lock)>
We have one problematic (C) use case in inet_csk_listen_stop() :
local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)
lockdep is not happy with this, as reported by Tetsuo Handa
It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.
Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise ECT(1) bit will get interpreted as RTO_ONLINK
and routing will fail with XfrmOutBundleGenError.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we need to check proper socket type within ipv4_conntrack_defrag
function before referencing the nodefrag flag.
For example the tun driver receive path produces skbs with
AF_UNSPEC socket type, and so current code is causing unwanted
fragmented packets going out.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checksum calculation in nf_nat_snmp_basic.
Based on patches by Clark Wang <wtweeker@163.com> and
Stephen Hemminger <shemminger@vyatta.com>.
https://bugzilla.kernel.org/show_bug.cgi?id=17622
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as rcu_read_unlock() is called, there is no guarantee current
thread can safely derefence t pointer, rcu protected.
Fix is to copy t->alloc_size in a temporary variable.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_me_harder can't create the route cache when the outdev is the same
with the indev for the skbs whichout a valid protocol set.
__mkroute_input functions has this check:
1998 if (skb->protocol != htons(ETH_P_IP)) {
1999 /* Not IP (i.e. ARP). Do not create route, if it is
2000 * invalid for proxy arp. DNAT routes are always valid.
2001 *
2002 * Proxy arp feature have been extended to allow, ARP
2003 * replies back to the same interface, to support
2004 * Private VLAN switch technologies. See arp.c.
2005 */
2006 if (out_dev == in_dev &&
2007 IN_DEV_PROXY_ARP_PVLAN(in_dev) == 0) {
2008 err = -EINVAL;
2009 goto cleanup;
2010 }
2011 }
This patch gives the new skb a valid protocol to bypass this check. In order
to make ipt_REJECT work with bridges, you also need to enable ip_forward.
This patch also fixes a regression. When we used skb_copy_expand(), we
didn't have this issue stated above, as the protocol was properly set.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I initially noticed this because of the compiler warning below, but it
does seem to be a valid concern in the case where ct_sip_get_header()
returns 0 in the first iteration of the while loop.
net/netfilter/nf_conntrack_sip.c: In function 'sip_help_tcp':
net/netfilter/nf_conntrack_sip.c:1379: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Simon Horman <horms@verge.net.au>
[Patrick: changed NF_DROP to NF_ACCEPT]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
transparent field of a socket is either inet_twsk(sk)->tw_transparent
for timewait sockets, or inet_sk(sk)->transparent for other sockets
(TCP/UDP).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Special care should be taken when slow path is hit in ip_fragment() :
When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.
Many thanks to Nick Bowler, who provided a very clean bug report and
test program.
Thanks to Jarek for reviewing my first patch and providing a V2
While Nick bisection pointed to commit 2b85a34e91 (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)
A side effect is to extend work done in commit b2722b1c3a
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Tested-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a RST comes in immediately after checking sk->sk_err, tcp_poll will
return POLLIN but not POLLOUT. Fix this by checking sk->sk_err at the end
of tcp_poll. Additionally, ensure the correct order of operations on SMP
machines with memory barriers.
Signed-off-by: Tom Marshall <tdm.code@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use explicit casts, since we really can't change the
types of structures exported to userspace which have been
around for 15 years or so.
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The family parameter xfrm_state_find is used to find a state matching a
certain policy. This value is set to the template's family
(encap_family) right before xfrm_state_find is called.
The family parameter is however also used to construct a temporary state
in xfrm_state_find itself which is wrong for inter-family scenarios
because it produces a selector for the wrong family. Since this selector
is included in the xfrm_user_acquire structure, user space programs
misinterpret IPv6 addresses as IPv4 and vice versa.
This patch splits up the original init_tempsel function into a part that
initializes the selector respectively the props and id of the temporary
state, to allow for differing ip address families whithin the state.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver doesn't fill the entire buffer, old
heap contents may remain, and if it also doesn't
update the length properly, this old heap content
will be copied back to userspace.
It is very unlikely that this happens in any of
the drivers using private ioctls since it would
show up as junk being reported by iwpriv, but it
seems better to be safe here, so use kzalloc.
Reported-by: Jeff Mahoney <jeffm@suse.com>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipv6 can be a module, we should test CONFIG_IPV6 and CONFIG_IPV6_MODULE
to enable ipv6 bits in ip_gre.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
dca: disable dca on IOAT ver.3.0 multiple-IOH platforms
netpoll: Disable IRQ around RCU dereference in netpoll_rx
sctp: Do not reset the packet during sctp_packet_config().
net/llc: storing negative error codes in unsigned short
MAINTAINERS: move atlx discussions to netdev
drivers/net/cxgb3/cxgb3_main.c: prevent reading uninitialized stack memory
drivers/net/eql.c: prevent reading uninitialized stack memory
drivers/net/usb/hso.c: prevent reading uninitialized memory
xfrm: dont assume rcu_read_lock in xfrm_output_one()
r8169: Handle rxfifo errors on 8168 chips
3c59x: Remove atomic context inside vortex_{set|get}_wol
tcp: Prevent overzealous packetization by SWS logic.
net: RPS needs to depend upon USE_GENERIC_SMP_HELPERS
phylib: fix PAL state machine restart on resume
net: use rcu_barrier() in rollback_registered_many
bonding: correctly process non-linear skbs
ipv4: enable getsockopt() for IP_NODEFRAG
ipv4: force_igmp_version ignored when a IGMPv3 query received
ppp: potential NULL dereference in ppp_mp_explode()
net/llc: make opt unsigned in llc_ui_setsockopt()
...
sctp_packet_config() is called when getting the packet ready
for appending of chunks. The function should not touch the
current state, since it's possible to ping-pong between two
transports when sending, and that can result packet corruption
followed by skb overlfow crash.
Reported-by: Thomas Dreibholz <dreibh@iem.uni-due.de>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the alloc_skb() fails then we return 65431 instead of -ENOBUFS
(-105).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_local_out() is called with rcu_read_lock() held from ip_queue_xmit()
but not from other call sites.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
You cannot invoke __smp_call_function_single() unless the
architecture sets this symbol.
Reported-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix the NFSv4 and RPCSEC_GSS Kconfig dependencies
statfs() gives ESTALE error
NFS: Fix a typo in nfs_sockaddr_match_ipaddr6
sunrpc: increase MAX_HASHTABLE_BITS to 14
gss:spkm3 miss returning error to caller when import security context
gss:krb5 miss returning error to caller when import security context
Remove incorrect do_vfs_lock message
SUNRPC: cleanup state-machine ordering
SUNRPC: Fix a race in rpc_info_open
SUNRPC: Fix race corrupting rpc upcall
Fix null dereference in call_allocate
netdev_wait_allrefs() waits that all references to a device vanishes.
It currently uses a _very_ pessimistic 250 ms delay between each probe.
Some users reported that no more than 4 devices can be dismantled per
second, this is a pretty serious problem for some setups.
Most of the time, a refcount is about to be released by an RCU callback,
that is still in flight because rollback_registered_many() uses a
synchronize_rcu() call instead of rcu_barrier(). Problem is visible if
number of online cpus is one, because synchronize_rcu() is then a no op.
time to remove 50 ipip tunnels on a UP machine :
before patch : real 11.910s
after patch : real 1.250s
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Octavian Purdila <opurdila@ixiacom.com>
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While integrating your man-pages patch for IP_NODEFRAG, I noticed
that this option is settable by setsockopt(), but not gettable by
getsockopt(). I suppose this is not intended. The (untested,
trivial) patch below adds getsockopt() support.
Signed-off-by: Michael kerrisk <mtk.manpages@gmail.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After all these years, it turns out that the
/proc/sys/net/ipv4/conf/*/force_igmp_version
parameter isn't fully implemented.
*Symptom*:
When set force_igmp_version to a value of 2, the kernel should only perform
multicast IGMPv2 operations (IETF rfc2236). An host-initiated Join message
will be sent as a IGMPv2 Join message. But if a IGMPv3 query message is
received, the host responds with a IGMPv3 join message. Per rfc3376 and
rfc2236, a IGMPv2 host should treat a IGMPv3 query as a IGMPv2 query and
respond with an IGMPv2 Join message.
*Consequences*:
This is an issue when a IGMPv3 capable switch is the querier and will only
issue IGMPv3 queries (which double as IGMPv2 querys) and there's an
intermediate switch that is only IGMPv2 capable. The intermediate switch
processes the initial v2 Join, but fails to recognize the IGMPv3 Join responses
to the Query, resulting in a dropped connection when the intermediate v2-only
switch times it out.
*Identifying issue in the kernel source*:
The issue is in this section of code (in net/ipv4/igmp.c), which is called when
an IGMP query is received (from mainline 2.6.36-rc3 gitweb):
...
A IGMPv3 query has a length >= 12 and no sources. This routine will exit after
line 880, setting the general query timer (random timeout between 0 and query
response time). This calls igmp_gq_timer_expire():
...
.. which only sends a v3 response. So if a v3 query is received, the kernel
always sends a v3 response.
IGMP queries happen once every 60 sec (per vlan), so the traffic is low. A
IGMPv3 query *is* a strict superset of a IGMPv2 query, so this patch properly
short circuit's the v3 behaviour.
One issue is that this does not address force_igmp_version=1. Then again, I've
never seen any IGMPv1 multicast equipment in the wild. However there is a lot
of v2-only equipment. If it's necessary to support the IGMPv1 case as well:
837 if (len == 8 || IGMP_V2_SEEN(in_dev) || IGMP_V1_SEEN(in_dev)) {
Signed-off-by: David S. Miller <davem@davemloft.net>
The members of struct llc_sock are unsigned so if we pass a negative
value for "opt" it can cause a sign bug. Also it can cause an integer
overflow when we multiply "opt * HZ".
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum size of the authcache is now set to 1024 (10 bits),
but on our server we need at least 4096 (12 bits). Increase
MAX_HASHTABLE_BITS to 14. This is a maximum of 16384 entries,
each containing a pointer (8 bytes on x86_64). This is
exactly the limit of kmalloc() (128K).
Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
spkm3 miss returning error to up layer when import security context,
it may be return ok though it has failed to import security context.
Signed-off-by: Bian Naimeng <biannm@cn.fujitsu.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
krb5 miss returning error to up layer when import security context,
it may be return ok though it has failed to import security context.
Signed-off-by: Bian Naimeng <biannm@cn.fujitsu.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is just a minor cleanup: net/sunrpc/clnt.c clarifies the rpc client
state machine by commenting each state and by laying out the functions
implementing each state in the order that each state is normally
executed (in the absence of errors).
The previous patch "Fix null dereference in call_allocate" changed the
order of the states. Move the functions and update the comments to
reflect the change.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There is a race between rpc_info_open and rpc_release_client()
in that nothing stops a process from opening the file after
the clnt->cl_kref goes to zero.
Fix this by using atomic_inc_unless_zero()...
Reported-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
If rpc_queue_upcall() adds a new upcall to the rpci->pipe list just
after rpc_pipe_release calls rpc_purge_list(), but before it calls
gss_pipe_release (as rpci->ops->release_pipe(inode)), then the latter
will free a message without deleting it from the rpci->pipe list.
We will be left with a freed object on the rpc->pipe list. Most
frequent symptoms are kernel crashes in rpc.gssd system calls on the
pipe in question.
Reported-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
In call_allocate we need to reach the auth in order to factor au_cslack
into the allocation.
As of a17c2153d2 "SUNRPC: Move the bound
cred to struct rpc_rqst", call_allocate attempts to do this by
dereferencing tk_client->cl_auth, however this is not guaranteed to be
defined--cl_auth can be zero in the case of gss context destruction (see
rpc_free_auth).
Reorder the client state machine to bind credentials before allocating,
so that we can instead reach the auth through the cred.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
The list_head conversion unearther an unnecessary flow
check. Since flow is always NULL here we don't need to
see if a matching flow exists already.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a list_has_sctp_addr function to simplify loop
Based on a patches by Dan Carpenter and David Miller
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).
Problem is that following sequence :
fd = socket(...)
connect(fd, &remote, ...)
not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)
Sequence is :
- autobind() : choose a random local port, insert socket in hash tables
[while local address is INADDR_ANY]
- connect() : set remote address and port, change local address to IP
given by a route lookup.
When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.
One solution to this problem is to rehash datagram socket if needed.
We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.
This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
