Issue description:
When an OTG port has been switched to device role and then switch back
to host role again, the USB 3.0 Host (XHCI) will not be able to detect
"plug in event of a connected USB 2.0/1.0 ((Highspeed and Fullspeed)
devices until system reboot.
Root cause and Solution:
There is a condition checking flag "ssusb->otg_switch.is_u3_drd" in
toggle_opstate(). At the end of role switch procedure, toggle_opstate()
will be called to set DC_SESSION and SOFT_CONN bit. If "is_u3_drd" was
set and switched the role to USB host 3.0, bit DC_SESSION and SOFT_CONN
will be skipped hence caused the port cannot detect connected USB 2.0
(Highspeed and Fullspeed) devices. Simply remove the condition check to
solve this issue.
Fixes: d0ed062a8b ("usb: mtu3: dual-role mode support")
Cc: stable@vger.kernel.org
Tested-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Tainping Fang <tianping.fang@mediatek.com>
Link: https://lore.kernel.org/r/20220419081245.21015-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a seldom issue that the controller access invalid address
and trigger devapc or emimpu violation. That is due to memory access
is out of order and cause gpd data is not correct.
Add mb() to prohibit compiler or cpu from reordering to make sure GPD
is fully written before setting its HWO.
Fixes: 48e0d3735a ("usb: mtu3: supports new QMU format")
Cc: stable@vger.kernel.org
Reported-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the Interval value from isoc/intr endpoint descriptor, no need
minus one. The original code doesn't cause transfer error for
normal cases, but it may have side effect with respond time of ERDY
or tPingTimeout.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211218095749.6250-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new API dev_pm_set_dedicated_wake_irq_reverse() to request
dedicated wake-up interrupt, due to we want to enable the wake IRQ
after running ->runtime_suspend().
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some platforms, e.g. 8183/8192, use low level latch way to keep
wakeup signal, it may latch a wrong signal if debounce more time,
and enable wakeup earlier.
____________________
ip_sleep ____/ \__________
___________________
wakeup_signal ____________/ \______
_______________________________
wakeup_en _______/
^ ^
|(1) |(2)
latch wakeup_signal mistakenly at (1), should latch it at (2);
Workaround: delay about 100us to enable wakeup, meanwhile decrease
debounce time.
Fixes: b1a344589e ("usb: mtu3: support ip-sleep wakeup for MT8183")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210826083637.33237-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Forgot 'return 0;' when suspend successfully, make the mistake
when I split patches.
Fixes: 6b587394c6 ("usb: mtu3: support suspend/resume for dual-role mode")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210826083637.33237-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support suspend/resume for dual-role mode including the single
port and multi-ports supported by host controller, when the host
supports mult-ports, only port0 (u2/u3) is used to support dual
role mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1626340078-29111-14-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a dedicated wakeup irq for runtime suspend/resume, and interrupts
names are provided if using wakeup irq, this patch only support host
mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1626340078-29111-11-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to disable specific usb2 host ports, it's useful when
a usb2 port is disabled on some platforms, but enabled on others
for the same SoC.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1626340078-29111-9-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use common helper ssusb_set_mode() to do role switch instead
of manual switch helper;
Remove unnecessary local variable when get role status
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-14-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now we mainly use usb-role-switch to set dual role mode, and all
three ways supported use the same function to switch mode, use
usb_role enum will make code clear
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When power down device IP, we can also power down device port,
then power on the port again when power on device ip, it's helpful
to make device ip enter ip sleep mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623139069-8173-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support ip-sleep wakeup for MT8183, it's similar to MT8173,
and it's also a specific one, but not following IPM rule.
Due to the index 2 already used by many DTS, it's better to keep
it unchanged for backward compatibility, treat specific ones without
following IPM rule as revision 1.x, meanwhile reserve 3~10 for later
revision that follows the IPM rule.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1616482975-17841-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable u3_ports_disabed contains a spelling mistake,
rename it to u3_ports_disabled.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210311092529.4898-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is using the wrong sizeof() so it does not allocate enough
memory. It allocates 32 bytes but 72 are required. That will lead to
memory corruption.
Fixes: ae07809255 ("usb: mtu3: add debugfs interface files")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ikqc4Mo2/0G72j@mwanda
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "nregs" member is not used. The code uses the "regset.nregs"
struct member instead.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ikv1QA3Do50D+R@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max_speed got from DTS may be not supported by the
hardware, so need check it, and assign a proper default
value. And make it clear by introducing a funtion.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-5-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disable interrupts, will also want to clear their status,
ensure it by calling mtu3_intr_status_clear() in
mtu3_intr_disable().
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CSR registers will be reset as default value if the
ports are disabled, so reinitialize them when the ports
are enabled again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
