commit c8b177b6e3 upstream.
Add another device ID for JBL Quantum 800. It requires the same quirk as
other JBL Quantum devices.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210831002531.116957-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66291b6adb upstream.
The change to restore the autosuspend from the disabled state uses a
wrong check: namely, it should have been the exact comparison of the
quirk_type instead of the bitwise and (&). Otherwise it matches
wrongly with the other quirk types.
Although re-enabling the autosuspend for the already enabled device
shouldn't matter much, it's better to fix the unbalanced call.
Fixes: 9799110825 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5hr1flh9ov.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4511781f95 ]
The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).
We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.
Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.
Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.
This earphone works fine on older kernel version load because
this is a newly-added behavior.
Fixes: d2e8f64125 ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b0084afde2 upstream.
These devices has two interfaces, but only the second interface
contains the capture endpoint, thus quirk is required to delay the
registration until the second interface appears.
Tested-by: Jakub Fišer <jakub@ufiseru.cz>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721235605.53741-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64752a95b7 upstream.
Recently we've added a new usb_mixer element type, USB_MIXER_BESPOKEN,
but it wasn't added in the table in snd_usb_mixer_dump_cval(). This
is no big problem since each bespoken type should have its own dump
method, but it still isn't disallowed to use the standard one, so we
should cover it as well. Along with it, define the table with the
explicit array initializer for avoiding other pitfalls.
Fixes: 785b6f29a7 ("ALSA: usb-audio: scarlett2: Fix wrong resume call")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210714084836.1977-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5d8e00803 ]
Mixer control put callbacks should return 1 if the value is changed.
Fix the sw_hw, level, pad, and button controls accordingly.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164645.GA9221@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5ddea9ce ]
The private->vol_updated flag was being checked outside of the
mutex_lock/unlock() of private->data_mutex leading to the volume data
being fetched twice from the device unnecessarily or old volume data
being returned.
Update scarlett2_*_ctl_get() and include the private->vol_updated flag
check inside the critical region.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20210620164643.GA9216@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cae0cf651a ]
Unlike some other functions, we can't pass NULL pointer to
free_pages_exact(). Add a proper NULL check for avoiding possible
Oops.
Link: https://lore.kernel.org/r/20210517131545.27252-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bae3ce4942 ]
For improving readability, convert camelCase fields, variables and
functions to the plain names with underscore. Also align the macros
to be capital letters.
All done via sed, no functional changes.
Note that you'll still see many coding style issues even after this
patch; the fixes will follow.
Link: https://lore.kernel.org/r/20210517131545.27252-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 785b6f29a7 upstream.
The current way of the scarlett2 mixer code managing the
usb_mixer_elem_info object is wrong in two ways: it passes its
internal index to the head.id field, and the val_type field is
uninitialized. This ended up with the wrong execution at the resume
because a bogus unit id is passed wrongly. Also, in the later code
extensions, we'll have more mixer elements, and passing the index will
overflow the unit id size (of 256).
This patch corrects those issues. It introduces a new value type,
USB_MIXER_BESPOKEN, which indicates a non-standard mixer element, and
use this type for all scarlett2 mixer elements, as well as
initializing the fixed unit id 0 for avoiding the overflow.
Tested-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/49721219f45b7e175e729b0d9d9c142fd8f4342a.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362372ceb6 upstream.
At extending the available mixer values for 32bit types, we forgot to
add the corresponding entries for the format dump in the proc output.
This may result in OOB access. Here adds the missing entries.
Fixes: bc18e31c30 ("ALSA: usb-audio: Fix parameter block size for UAC2 control requests")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210622090647.14021-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b57bb76a upstream.
This reverts commit 4667a6fc17.
Takashi writes:
I have already started working on the bigger cleanup of this driver
code based on 5.13-rc1, so could you drop this revert?
I missed our previous discussion about this, my fault for applying it.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4667a6fc17 ]
This reverts commit a2c6433ee5.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original patch was incorrect, and would leak memory if the error
path the patch added was hit.
Cc: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210503115736.2104747-37-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 265d1a90e4 upstream.
Add separate init function to call the existing controls_create
function so a custom error can be displayed if initialisation fails.
Use info level instead of error for notifications.
Display the VID/PID so device_setup is targeted to the right device.
Display "enabled" message to easily confirm that the driver is loaded.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/b5d140c65f640faf2427e085fbbc0297b32e5fce.1621584566.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 764fa6e686 upstream.
Use usb_rcvctrlpipe() not usb_sndctrlpipe() for USB control input in
the Scarlett Gen 2 mixer driver. This fixes the device hang during
initialisation when used with the ehci-pci host driver.
Fixes: 9e4d5c1be2 ("ALSA: usb-audio: Scarlett Gen 2 mixer interface")
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/66a3d05dac325d5b53e4930578e143cef1f50dbe.1621584566.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05ca447630 upstream.
The initialization of MIDI devices that are found on some LINE6
drivers are currently done in a racy way; namely, the MIDI buffer
instance is allocated and initialized in each private_init callback
while the communication with the interface is already started via
line6_init_cap_control() call before that point. This may lead to
Oops in line6_data_received() when a spurious event is received, as
reported by syzkaller.
This patch moves the MIDI initialization to line6_init_cap_control()
as well instead of the too-lately-called private_init for avoiding the
race. Also this reduces slightly more lines, so it's a win-win
change.
Reported-by: syzbot+0d2b3feb0a2887862e06@syzkallerlkml..appspotmail.com
Link: https://lore.kernel.org/r/000000000000a4be9405c28520de@google.com
Link: https://lore.kernel.org/r/20210517132725.GA50495@hyeyoo
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210518083939.1927-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cfd577acb7 ]
Currently when the call to usb_urb_ep_type_check fails (returning -EINVAL)
the error return path returns -ENOMEM via the exit label "error". Other
uses of the same error exit label set the err variable to -ENOMEM but this
is not being used. I believe the original intent was for the error exit
path to return the value in err rather than the hard coded -ENOMEM, so
return this rather than the hard coded -ENOMEM.
Addresses-Coverity: ("Unused value")
Fixes: 738d9edcfd ("ALSA: usb-audio: Add sanity checks for invalid EPs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210420134719.381409-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fb45414ae ]
There are a few calls of usb_driver_claim_interface() but all of those
miss the proper error checks, as reported by Coverity. This patch
adds those missing checks.
Along with it, replace the magic pointer with -1 with a constant
USB_AUDIO_IFACE_UNUSED for better readability.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1475943 ("Error handling issues")
Addresses-Coverity-ID: 1475944 ("Error handling issues")
Addresses-Coverity-ID: 1475945 ("Error handling issues")
Fixes: b1ce7ba619 ("ALSA: usb-audio: claim autodetected PCM interfaces all at once")
Fixes: e5779998bf ("ALSA: usb-audio: refactor code")
Link: https://lore.kernel.org/r/202104051059.FB7F3016@keescook
Link: https://lore.kernel.org/r/20210406113534.30455-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d2e8f64125 upstream.
In the current code, we have some assumption that the audio clock
selector has been set up implicitly and don't want to touch it unless
it's really needed for the fallback autoclock setup. This works for
most devices but some seem having a problem. Partially this was
covered for the devices with a single connector at the initialization
phase (commit 086b957cc1 "ALSA: usb-audio: Skip the clock selector
inquiry for single connections"), but also there are cases where the
wrong clock set up is kept silently. The latter seems to be the cause
of the noises on Behringer devices.
In this patch, we explicitly set up the audio clock selector whenever
the appropriate node is found.
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199327
Link: https://lore.kernel.org/r/CAEsQvcvF7LnO8PxyyCxuRCx=7jNeSCvFAd-+dE0g_rd1rOxxdw@mail.gmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210413084152.32325-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 625bd5a616 upstream.
Logitech ConferenceCam Connect is a compound USB device with UVC and
UAC. Not 100% reproducible but sometimes it keeps responding STALL to
every control transfer once it receives get_freq request.
This patch adds 046d:0x084c to a snd_usb_get_sample_rate_quirk list.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203419
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210324105153.2322881-1-ikjn@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50b1affc89 upstream.
The shifting of the u8 integer device by 24 bits to the left will
be promoted to a 32 bit signed int and then sign-extended to a
64 bit unsigned long. In the event that the top bit of device is
set then all then all the upper 32 bits of the unsigned long will
end up as also being set because of the sign-extension. Fix this
by casting device to an unsigned long before the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: a07df82c79 ("ALSA: usb-audio: Add DJM750 to Pioneer mixer quirk")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210318132008.15266-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 257d2d7e9e upstream
In the later patch, we're going to issue the PCM sync_stop calls at
disconnection. But currently the USB-audio driver can't handle it
because it has a check of shutdown flag for stopping the URBs. This
is basically superfluous (the stopping URBs are safe at disconnection
state), so let's drop the check.
Fixes: dc5eafe778 ("ALSA: usb-audio: Support PCM sync_stop")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5aa956eae upstream.
The problem was in wrong "if" placement. chip->quirk_type is freed
in snd_card_free_when_closed(), but inside if statement it's accesed.
Fixes: 9799110825 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/16da19126ff461e5e64a9aec648cce28fb8ed73e.1615242183.git.paskripkin@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9799110825 upstream.
Rear audio on Lenovo ThinkStation P620 stops working after commit
1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo
ThinkStation P620"):
[ 6.013526] usbcore: registered new interface driver snd-usb-audio
[ 6.023064] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023083] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023090] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023098] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023103] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023110] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045846] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045866] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045877] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045886] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045894] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045908] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
I overlooked the issue because when I was working on the said commit,
only the front audio is tested. Apology for that.
Changing supports_autosuspend in driver is too late for disabling
autosuspend, because it was already used by USB probe routine, so it can
break the balance on the following code that depends on
supports_autosuspend.
Fix it by using usb_disable_autosuspend() helper, and balance the
suspend count in disconnect callback.
Fixes: 1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo ThinkStation P620")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304043419.287191-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06abcb18b3 upstream.
Other Plantronics headset models seem requiring the same workaround as
C320-M to add the 20ms delay for the control messages, too. Apply the
workaround generically for devices with the vendor ID 0x047f.
Note that the problem didn't surface before 5.11 just with luck.
Since 5.11 got a big code rewrite about the stream handling, the
parameter setup procedure has changed, and this seemed triggering the
problem more often.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182552
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304085009.4770-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc7c5c208e upstream.
The microphone in the Plantronics C320-M headset will randomly
fail to initialize properly, at least when using Microsoft Teams.
Introducing a 20ms delay on the control messages appears to
resolve the issue.
Link: https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/issues/1065
Tested-by: Andreas Kempe <kempe@lysator.liu.se>
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303181405.39835-1-john.ernberg@actia.se
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fee03efc69 ]
This commit adds mixer quirks for the Pioneer DJM-900NXS2 mixer. This
device has 6 capture channels, 5 of them allow setting the signal
source. This adds controls for these, similar to the DJM-250Mk2.
However, playpack channels are not controllable via software like on the
250Mk2, as they can only be set manually on the mixing console.
Read-only controls showing the currently selected playback channels are
omitted.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Link: https://lore.kernel.org/r/20210205215116.258724-2-fabian@lesniak-it.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a07df82c79 ]
This allows for N different devices to use the pioneer mixer quirk for
setting capture/record type and recording level. The impementation has
not changed much with the exception of an additional mask on
private_value to allow storing of a device index:
DEVICE MASK 0xff000000
GROUP_MASK 0x00ff0000
VALUE_MASK 0x0000ffff
This could be improved by changing the arrays of wValues for each
channel to contain named definitions (e.g. SND_DJM_CAP_LINE). It would
improve readability and perhaps would allow using the same array for
multiple channels. The channel number can be specified on the control
next to the wIndex.
Feedback is very much appreciated as I'm not the most proficient C
programmer but am learning as I go.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210205184256.10201-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 21cba9c535 upstream.
Some USB audio firmware seem to report broken dB values for the volume
controls, and this screws up applications like PulseAudio who blindly
trusts the given data. For example, Edifier G2000 reports a PCM
volume from -128dB to -127dB, and this results in barely inaudible
sound.
This patch adds a sort of sanity check at parsing the dB values in
USB-audio driver and disables the dB reporting if the range looks
bogus. Here, we assume -96dB as the bottom line of the max dB.
Note that, if one can figure out that proper dB range later, it can be
patched in the mixer maps.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211929
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210227105737.3656-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11302bb69e upstream.
The Corsair Virtuoso SE RGB Wireless is a USB headset with a mic and a
sidetone feature. Assign the Corsair Virtuoso name map to the SE product
ids as well, in order to label its mixer appropriately and allow
userspace to pick the correct volume controls.
Signed-off-by: Andrea Fagiani <andfagiani@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/40bbdf55-f854-e2ee-87b4-183e6451352c@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb3c293b82 upstream.
The commit f274baa49b ("ALSA: usb-audio: Allow non-vmalloc buffer
for PCM buffers") introduced the mode to allocate coherent pages for
PCM buffers, and it used bus->controller device as its DMA device.
It turned out, however, that bus->sysdev is a more appropriate device
to be used for DMA mapping in HCD code.
This patch corrects the device reference accordingly.
Note that, on most platforms, both point to the very same device,
hence this patch doesn't change anything practically. But on
platforms like xhcd-plat hcd, the change becomes effective.
Fixes: f274baa49b ("ALSA: usb-audio: Allow non-vmalloc buffer for PCM buffers")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210205144559.29555-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c06ccf3ebb upstream.
The calculation of in_cables and out_cables bitmaps are done with the
bit shift by the value from the descriptor, which is an arbitrary
value, and can lead to UBSAN shift-out-of-bounds warnings.
Fix it by filtering the bad descriptor values with the check of the
upper bound 0x10 (the cable bitmaps are 16 bits).
Reported-by: syzbot+92e45ae45543f89e8c88@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223174557.10249-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9df28edce7 upstream.
Some buggy firmware don't give the current sample rate but leaves
zero. Handle this case more gracefully without warning but just skip
the current rate verification from the next time.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201218145858.2357-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dde8ffd0 upstream.
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Found one more Logitech device, BCC950 ConferenceCam, which needs
the same delay here. This makes 3 out of 3 devices I have tried.
Therefore, add a delay for all Logitech devices as it does not hurt.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org> # 4.19.y, 5.4.y
Link: https://lore.kernel.org/r/20201117122803.24310-1-joakim.tjernlund@infinera.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
