Its not needed, so just pass the hardware RX status.
We'll be simplfying ath_rx_prepare() with code we can share
between ath9k and ath9k_htc. This will help make that code
easier to read and manage.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k virtual wiphys all share the same internal buffer space
for TX but they do not share the mac80211 skb queues. When
ath9k detects it is running low on buffer space to TX it tells
mac80211 to stop sending it skbs its way but it always does
this only for the primary wiphy. This means mac80211 won't know
its best to avoid sending ath9k more skbs on a separate virtual
wiphy. The same issue is present for reliving the skb queue.
Since ath9k does not keep track of which virtual wiphy is hammering
on TX silence all wiphy's TX when we're low on buffer space. When
we're free on buffer space only bother informing the virtual wiphy
which is active that we have free buffers.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using virtual wiphys the base sc->hw was being used, the correct
hw is passed along the caller already so just use that.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath9k virtual wiphys are used the sc->hw will not always represent
the active hw, instead we need to get it from the skb->cb private
driver area. This ensures the right hw is used to find a sta for
the TX'd skb.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use the ieee80211_hw for radio enable/disable but the wrong
structure hw was being used in consideration for virtual wiphys
as each virtual wiphy has its own ieee80211_hw struct.
Just pass the hw struct to ensure we use the right one. This should
fix the hw used and passed for radio enable/disable. This includes
the stoping / starting of the software TX queues so mac80211 doesn't
send us data for a specific virtual wiphy. ath9k already takes care
of pausing virtual wiphys and stopping the respective queues on its
own, but this should handle the idle mac80211 conf calls as well.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this now uses the proper hw which should mean finding the
right sta when using ath9k virtual wiphy stuff. Only
advantage I see here is getting the rssi properly updated
so the 'fix' itself isn't that great, but at least this
is correct.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_get_virt_hw() is required on RX to determine for which virtual
wiphy an skb came in for. Instead of searching for the hw twice do
it only once.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports its own virtual wiphys. The hardware code
relies on the ieee80211_hw for the present interface but
with recent changes introduced the common->hw was never
updated and is required for virtual wiphys.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way idle configuration detection was implemented as
busted due to the fact that it assumed the ath9k virtual wiphy,
the aphy, would be marked as inactive if it was not used but
it turns out an aphy is always active if its the only wiphy
present. We need to distinguish between aphy activity and
idleness so we now add an idle bool for the aphy and mark
it as such based on the passed IEEE80211_CONF_CHANGE_IDLE
from mac80211.
Previous to all_wiphys_idle would never be true when using
only one device so we never really were using
IEEE80211_CONF_CHANGE_IDLE -- we never turned the radio
off or on upon IEEE80211_CONF_CHANGE_IDLE changes as radio
changes depended on all_wiphys_idle being true either to
turn the radio on or off. Since it was always false for
one device this code was doing nothing.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I may have botched my merge conflict resolution instructions for Dave...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling rt2800usb as a built-in driver (as opposed to a as a module) the build fails. See
http://marc.info/?l=linux-wireless&m=125768687711034&w=2 for details.
Fix it by properly including <linux/usb.h> from rt2x00usb.h
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure all drivers can benefit of the assignment of the interface
type of an adapter, instead of keeping it for rt2800 only.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CCS_START_NETWORK is declared in drivers/net/wireless/rayctl.h with the
comment Values for cmd. status is previously compared to
CCS_COMMAND_COMPLETE, which is declared in the same file with the comment
Values for buffer_status. Finally, it is possible at this point that cmd
is CCS_START_NETWORK, because it is compared to that value in an enclosing
switch that has CCS_START_NETWORK as one of two case labels around this code.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the RX error path for rev>=8 devices.
The wrong register size and definitions were used.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add txq_id info to "Tx queue requesting wakeup" debug message
Add "Rx queue requesting wakeup" debug message
Move clear of CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ to be after nearby
iwl_write_prph(), since iwl_write_prph() sets it and clears it. Almost
removed it entirely, but just making sure in case someone removes the
iwl_write_prph()! Also remove unneeded priv->lock usage; this is now
handled by priv->reg_lock within iwl_clear_bit().
Join a couple of lines that had unneeded line returns.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Follow-up to "update write pointers for all tx queues after wakeup"; that
patch changed iwl_irq_tasklet_legacy(), but not iwl_irq_tasklet(), so
newer devices were not covered.
Comments from original patch:
Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5. This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues. Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.
This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take advantage of device's auto-increment for SRAM reads to eliminate extra
write address accesses.
Grab/release NIC access before/after entire read sequence, rather than for
each read individually.
After a quick check of dmesg logs, this seems to double Event Log dump speed,
reducing from about 20 milliseconds to about 10 milliseconds for 512 entries
using 3945.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device provides bad values for Event Log parameters (due to being asleep
or SRAM corruption, etc.), the size can be very, very large (e.g. 0xa5a5a5a5),
which can flood system log.
Sanity-check capacity and next_entry values and limit to reasonable size dump.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not use AP's SM_PS setting for our own SM_PS setting.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the support for all the PCI_IDs never make into production
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.
Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is part of the code, but the comment doesn't have it,
add pointers to the code and the FIFO usage for 5000 and
up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove un-used parameter "recovery_rxon" from "priv" data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added that code setting the swq_id, I evidently
did not understand the distinction between FIFO and TX
queue yet and added code to compare a queue ID and a
FIFO number, which is bogus.
However, the code there need not be this specific, it
can just set all queues to the identity mapping which
will be overwritten by the aggregation queue code. As
a bit of defensive coding, don't assign an swq_id to
the command queue so that if we ever use it for frames
we notice quickly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fourth queue (command queue) is already activated in
the loop above that also maps it to the command FIFO and
therefore doesn't need to be marked as activated again.
Also change the TODO comment to be accurate -- we need
to initialise the _queues_, not FIFOs, and map them to
device FIFOs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For both 6x00 and 6x50 series devices, periodic Tx IQ calibration is
disabled in uCode, driver do not need to set the periodic Tx/IQ calibration
bit in calibration command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use configured valid rx chains in scan command instead of ANT_ABC, correcting
valid rx chain configuration of 4965, should be ANT_ABC instead of ANT_AB.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing scan in power saving mode, choose only 1 valid RX chain instead of
turning all chains on.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help debug rx related issues, if IWL_DEBUG_RADIO flag is set, print
the rxon configuration when rxon host command send to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allocate 128 bytes linear buffer for rx skb. The first 64 bytes is
reserved for mac80211 usage (for radiotap header expansion, etc).
The frame header starts from the second 64 bytes.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since these messages indicate failure we would be interested in seeing them
always.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not mess with the original skb, but allocate an independent bouncebuffer.
This protects against bad interference with mac80211's assumptions about
the skb (which already caused bugs).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some usbnet drivers update link state while others do not due to
hardware limitations. Add a flag to distinguish those that do, and
set the link down initially for their devices.
This is intended to fix this bug: http://bugs.debian.org/444043
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DMA_BIT_MASK(44) instead of deprecated DMA_44BIT_MASK
Signed-off-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failing to allocate MSI-X vectors is not an error and should not be
printed as such
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Making sure that whenever the FW/HW is configured for GSO, it is also
configured to CSUM offload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace run-time string formatting with preprocessor string
manipulation.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace run-time string formatting with preprocessor string
manipulation.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to a missing header include, sparse generates the following warnings:
CHECK drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the GPIOs for the BenQ Joybook netbook.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped. Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Add an interface to lock/unlock an I2C bus segment
i2c-piix4: Modify code name SB900 to Hudson-2
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net/fsl_pq_mdio: add module license GPL
can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo()
can: should not use __dev_get_by_index() without locks
hisax: remove bad udelay call to fix build error on ARM
ipip: Fix handling of DF packets when pmtudisc is OFF
qlge: Set PCIe reset type for EEH to fundamental.
qlge: Fix early exit from mbox cmd complete wait.
ixgbe: fix traffic hangs on Tx with ioatdma loaded
ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabled
ixgbe: Fix gso_max_size for 82599 when DCB is enabled
macsonic: fix crash on PowerBook 520
NET: cassini, fix lock imbalance
ems_usb: Fix byte order issues on big endian machines
be2net: Bug fix to send config commands to hardware after netdev_register
be2net: fix to set proper flow control on resume
netfilter: xt_connlimit: fix regression caused by zero family value
rt2x00: Don't queue ieee80211 work after USB removal
Revert "ipw2200: fix oops on missing firmware"
decnet: netdevice refcount leak
netfilter: nf_nat: fix NAT issue in 2.6.30.4+
...
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to not support userspace specifying the
network namespace during device creation, and it makes it easier
to create a network device and pass it to a child network namespace
with a well known name.
We have to be careful to ensure that the target network namespace
for the new device exists through the life of the call. To keep
that logic clear I have factored out the network namespace grabbing
logic into rtnl_link_get_net.
In addtion we need to continue to pass the source network namespace
to the rtnl_link_ops.newlink method so that we can find the base
device source network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
or it will taint the kernel and fail to load becuase
of_address_to_resource() is GPL only.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo()
is thrown when the CAN device is registered due to insufficient
skb space, as reported by various users. This patch adds the
rtnl_link_ops "get_size" to fix the problem. I think this patch
is required for more recent kernels as well, even if no WARN_ON
dumps are triggered. Maybe we also need "get_xstats_size" for
the CAN xstats.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fba4ed030c ("gianfar: Add Multiple
Queue Support") introduced the following warnings:
CHECK gianfar.c
gianfar.c:333:8: warning: incorrect type in assignment (different address spaces)
gianfar.c:333:8: expected unsigned int [usertype] *baddr
gianfar.c:333:8: got unsigned int [noderef] <asn:2>*<noident>
[... 67 lines skipped ...]
gianfar.c:2565:3: warning: incorrect type in argument 1 (different type sizes)
gianfar.c:2565:3: expected unsigned long const *addr
gianfar.c:2565:3: got unsigned int *<noident>
CC gianfar.o
gianfar.c: In function 'gfar_probe':
gianfar.c:985: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:985: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:993: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:993: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c: In function 'gfar_configure_coalescing':
gianfar.c:1680: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:1680: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:1688: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:1688: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c: In function 'gfar_poll':
gianfar.c:2565: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:2565: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type
gianfar.c:2566: warning: passing argument 2 of 'test_bit' from incompatible pointer type
gianfar.c:2585: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Following warnings left unfixed (looks like sparse doesn't like
locks in loops, so __acquires/__releases() doesn't help):
gianfar.c:441:40: warning: context imbalance in 'lock_rx_qs': wrong count at exit
gianfar.c:441:40: context '<noident>': wanted 0, got 1
gianfar.c:449:40: warning: context imbalance in 'lock_tx_qs': wrong count at exit
gianfar.c:449:40: context '<noident>': wanted 0, got 1
gianfar.c:458:3: warning: context imbalance in 'unlock_rx_qs': __context__ statement expected different context
gianfar.c:458:3: context '<noident>': wanted >= 0, got -1
gianfar.c:466:3: warning: context imbalance in 'unlock_tx_qs': __context__ statement expected different context
gianfar.c:466:3: context '<noident>': wanted >= 0, got -1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following warnings:
fsl_pq_mdio.c:112:38: warning: cast adds address space to expression (<asn:2>)
fsl_pq_mdio.c:124:38: warning: cast adds address space to expression (<asn:2>)
fsl_pq_mdio.c:133:38: warning: cast adds address space to expression (<asn:2>)
fsl_pq_mdio.c:414:11: warning: cast adds address space to expression (<asn:2>)
Instead of adding __force all over the place, introduce convenient
fsl_pq_mdio_get_regs() call that does the ugly casting just once.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1d2397d742 ("fsl_pq_mdio: Add
Suport for etsec2.0 devices") introduced the following warnings:
CHECK fsl_pq_mdio.c
fsl_pq_mdio.c:287:22: warning: incorrect type in initializer (different base types)
fsl_pq_mdio.c:287:22: expected unknown type 11 const *__mptr
fsl_pq_mdio.c:287:22: got unsigned long long [unsigned] [assigned] [usertype] addr
fsl_pq_mdio.c:287:19: warning: incorrect type in assignment (different base types)
fsl_pq_mdio.c:287:19: expected unsigned long long [unsigned] [usertype] ioremap_miimcfg
fsl_pq_mdio.c:287:19: got struct fsl_pq_mdio *<noident>
CC fsl_pq_mdio.o
fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
fsl_pq_mdio.c:287: warning: initialization makes pointer from integer without a cast
fsl_pq_mdio.c:287: warning: assignment makes integer from pointer without a cast
These warnings are not easy to fix without ugly __force casts. So,
instead of introducing the casts, rework the code to substitute an
offset from an already mapped area. This makes the code a lot simpler
and less duplicated.
Plus, from now on we don't actually map reserved registers on
non-etsec2.0 devices, so we have more chances to catch programming
errors.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers need to be able to prevent access to an I2C bus segment
for a specific period of time. Add an interface for them to do so
without twiddling with i2c-core internals.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
change atl1c_buffer struct, use "u16 flags" instead of "u16 state"
to store more infomation for atl1c_buffer, and restructure clean
atl1c_buffer procedure, add common api atl1c_clean_buffer.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slip and a few other drivers use the same ioctl numbers on
tty devices that are normally meant for sockets. This causes
problems with our compat_ioctl handling that tries to convert
the data structures in a different format.
Fortunately, these five drivers all use 32 bit compatible
data structures in the ioctl numbers, so we can just add
a trivial compat_ioctl conversion function to each of them.
SIOCSIFENCAP and SIOCGIFENCAP do not need to live in
fs/compat_ioctl.c after this any more, and they are not
used on any sockets.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tun driver is the only code in the kernel that operates
on a character device with struct ifreq. Change the driver
to handle the conversion itself so we can contain the
remaining ifreq handling in the socket layer.
This also fixes a bug in the handling of invalid ioctl
numbers on an unbound tun device. The driver treats this
as a TUNSETIFF in native mode, but there is no way for
the generic compat_ioctl() function to emulate this
behaviour. Possibly the driver was only doing this
accidentally anyway, but if any code relies on this
misfeature, it now also works in compat mode.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device requires a fundamental reset when recovering from EEH.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This line was accidentally left out of the previous commit #
da03945140 ("qlge: Fix firmware mailbox
command timeout.").
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ioatdma was loaded we we were unable to transmit traffic. We weren't
using the correct registers in ixgbe_update_tx_dca for 82599 systems.
Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before
modifying MTQC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding
TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a
function to map from the tx_ring hw reg_idx to the correspodning TC and read
TFCS accordingly.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No-one seems to know where the PowerBook 500 series store their ethernet
MAC addresses. So, rather than crash, use a MAC address from the SONIC
CAM. Failing that, generate a random one.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that one error path in cas_open omits to unlock pm_mutex.
Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPC-USB is using a ARM7 core with little endian byte order. The "id" field
in can_msg needs byte order conversion from/to CPU byte order.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending config commands to be2 hardware before netdev_register is
completed, is sometimes causing the async link notification to arrive
even before the driver is ready to handle it. The commands for vlan
config and flow control settings can infact wait till be_open.
This patch takes care of that.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If be2 goes into suspend after a user changes the flow control settings,
we are not programming them back after resume. This patch takes care of it.
We now get the flow control settings before going to suspend mode and
then apply them during resume.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 88w8366 firmware receive descriptor format,
and add the 88w8366 PCI ID.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the AP version of the GET_HW_SPEC command, as well as the
SET_HW_SPEC command, for initialising AP firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the AP version of the command uses a different format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As different chip/firmware combinations support different
interface types.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the receive descriptor format is determined by the firmware running
on the hardware and not by the hardware itself, and as these
descriptor formats vary a bit between different firmware releases,
abstract out the receive descriptor init/refill/process methods, and
allow choosing between different formats at run time depending on the
chip and firmware we're running on.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of reading back the unmap address from the receive
descriptor when doing receive processing, use DECLARE_PCI_UNMAP_ADDR
and pci_unmap_addr{,set}() to keep track of these addresses.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP and STA firmware images provide a different signature in the
HIU_INT_CODE register after loading. Record which of the signatures
we saw, as it determines which command sequences to use later on.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To allow use of a more flexible firmware file naming scheme.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for adding support for more device types, introduce a
new structure, mwl8k_device_info, where per-device information can
be stored, and change the pci id table driver data from an integer
indicating only the part number to a pointer to a mwl8k_device_info
structure.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qual member of ieee80211_rx_status is deprecated. As a result, this
driver no longer needs to calculate a quality value.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the deprecation of the qual member of ieee80211_rx_status, that
calculation and an associated constant can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the deprecation of the qual member of ieee80211_rx_status, that
calculation and an associated constant can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add LED support for a Foxconn AR242X module, found on
the Acer Aspire One models AO751h/AO531h
Signed-off-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance rt2x00 infrastructure by adding explicit information
about used chipset interface to struct rt2x00_chip.
The new field will be used by rt2800 drivers for rt2800 library.
Also add commonly used rt2x00_intf_is_pci() and rt2x00_intf_is_usb()
helpers to make code easier to read (noticed by Ivo van Doorn).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updated debugging scripts are located here:
http://www.kernel.org/pub/linux/kernel/people/bart/rt2800/scripts/
(they also work fine with older drivers)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RXINFO_DESC_SIZE definition and use it instead of abusing
RXD_DESC_SIZE one (TXD_DESC_SIZE and RXD_DESC_SIZE are specific
to PCI version of the chipset).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change type of 'length' argument from u16 to u32 (all arguments
match rt2x00usb_register_multi[read,write]() ones now).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add const to 'field' argument of rt2x00usb_regbusy_read()
(all arguments match rt2x00pci_regbusy_read() ones now).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add const to 'value' argument of rt2x00usb_register_multiwrite()
(all arguments match rt2x00pci_register_multiwrite() ones now).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add chipset registers access abstraction layer and prepare for later
code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add chipset registers access abstraction layer and prepare for later
code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance rt2x00 infrastructure by adding driver specific field to
struct rt2x00_dev.
The new field will be used by rt2800 drivers for chipset registers
access abstraction layer.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents the rt2x00 driver from queueing ieee80211 work after the
USB card has been removed, preventing a kernel panic.
Signed-off-by: Sean Cross <sean@chumby.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic __sock_create function has a kern argument which allows the
security system to make decisions based on if a socket is being created by
the kernel or by userspace. This patch passes that flag to the
net_proto_family specific create function, so it can do the same thing.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In BCM8481 when link speed goes from 1G to 10M, driver received timeout
since the MAC clock hasn't synced yet with the new speed, so it is required
first to program the MAC with the new speed, and only then configure other
parameters
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new phy type BCM84823 (Dual copper-port phy)
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify BCM8706 link initialization sequence so that first it link up
between Serdes and BCM8706, and only then between BCM8706 to network
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parallel detect is used, flow-control is set to the
req_fc_auto_adv instead of none.
Motive: when 577xx is FC configuration is set to AUTO, while LP speed
is set to FORCE mode and FC to force RX/TX, link would come up using
parallel detect, and the FC will be set to NONE since FC capabilities
were not negotiated, although the LP is setting FC to force RX/TX.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Advertise 1G KX4 in CL73 when 1G speed capability is enabled
- Add flow-control negotiation over CL73
- External loopback test on Serdes should be done in FORCE mode, since in
CL73 it is unable to link up with the same core using AUTONEG
- Fix bnx2x_set_led function to support CL73 link leds
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Parallel-Detect for 10G and 1G only if the relevant speed
capability is enabled
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit
3d1285b (move virtnet_remove to .devexit.text)
introduced the first reference to __devexit in struct virtio_driver
virtio_net which upset modpost ("Section mismatch in reference from the
variable virtio_net to the function .devexit.text:virtnet_remove()").
Fix this by renaming virtio_net to virtio_net_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Blame-taken-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend/resume capability to TI DaVinci EMAC driver.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187
USB stick, or unloading the driver rtl8187 using rmmod will cause a
kernel oops. There are at least two forms of the failure, (1) BUG:
Scheduling while atomic, and (2) a fatal kernel page fault. This
problem is reported in Bugzilla #14539.
This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2,
thus it is technically a regression; however, bisection did not locate
any faulty patch. The fix was found by comparing the faulty code in
rtl8187 with p54usb. My interpretation is that the handling of work
queues in mac80211 changed enough to the LEDs to be unregistered
before tasks on the work queues are cancelled. Previously, these
actions could be done in either order.
(Herton Ronaldo Krzesinski <herton@mandriva.com.br> reports that the
code is the same in 2.6.31, so this may be a candidate for 2.6.31.x.
-- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Rick Farina <sidhayn@gmail.com>
Tested-by: Rick Farina <sidhayn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since struct hw_key_entry is 32-bytes large and is smaller than
CSR cache size (which is 64-bytes large) we can use the standard
rt2x00usb_register_multiwrite() helper to set key entries.
This cleanup is a part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit tested by hardware is TXD_W3_WIV and its value
equals the negated value of ENTRY_TXD_ENCRYPT_IV bit.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Registers used for indirect BBP and RF registers access are
respectively BBPCSR and RFCSR, also make it clear that all CSR
registers access goes through rt2x00pci_register_[read,write]()
methods.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on rt2800usb patch from Benoit PAPILLAULT
(commit 1761631083).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver should write the read request into RF_CSR_CFG register
and not BBP_CSR_CFG one in rt2800usb_rfcsr_read().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document known issues with the driver to aid distribution makers,
users and developers in making informed decisions instead of wasting
their time needlessly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document known issues with the driver to aid distribution makers,
users and developers in making informed decisions instead of wasting
their time needlessly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.
For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Map BAR0 as well, as we need to write to it during init on some chips.
Also, if BAR0 is a 64bit BAR, the register BAR becomes BAR2, so try
mapping BAR2 if mapping BAR1 fails.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving a frame, report the antenna info, long/short preamble
status, 20/40 MHz flag, long/short guard interval status, MCS/legacy
rate status, and MCS/legacy rate index to the stack.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since each firmware block takes on the order of several hundred usec
to upload to the hardware, using msleep in the inner loop would make
the firmware loading process take a lot more time than just doing
busy-waiting like we do now. But if we keep the busy-waiting, we can
at least add a cond_resched() to the inner loop so that we give other
tasks a chance to run while the firmware is being loaded.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there is no STA interface configured, clear the hardware MAC
address to prevent ACKing frames sent to our MAC address.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FIF_BCN_PRBRESP_PROMISC is not set, we enable the hardware's BSS
filter so that we'll only see packets destined for our BSS. But if no
STA interfaces have been configured, we would end up passing the BSSID
00:00:00:00:00:00 into the POST_SCAN command, which actually disables
the hardware's BSS filter, as it's not a valid BSSID.
Fix this by passing in 01:00:00:00:00:00 instead (the criterion is
that the OUI part of the BSSID must be nonzero), and add comments to
explain what PRE_SCAN and POST_SCAN do.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k's ->prepare_multicast() currently just enables reception of
all multicast packets, which is somewhat ineffective.
Fix this by either disabling all multicast RX, enabling multicast
RX according to the multicast address filter table, or enabling all
multicast RX, depending on whether ->prepare_multicast() was given
any multicast addresses and whether the hardware multicast address
filter table is large enough to fit all requested addresses.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Minor changes to the transmit quiescing logic:
- Clarify the locking rules for ->tx_wait: only the holder of fw_mutex
can wait for the TX path to become idle, but tx_wait itself is read
and cleared by the TX reclaim tasklet under tx_lock.
- Inline mwl8k_txq_busy() in its callers.
- There's no need to kick the transmitter again in
mwl8k_tx_wait_empty(), since it will have been kicked when the
packets currently in the TX ring were added to it.
- If the TX ring didn't drain in time, run mwl8k_scan_tx_ring() after
reading priv->pending_pkts without dropping tx_lock in between.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The GET_STAT command doesn't have an 'action' field like other
commands do, so remove it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_notifier'
wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_notifier'
Driver is doing some filtering based on IP addresses...
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use spin_trylock_irqsave instead of open-coded
local_irq_save+spin_trylock.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bnx2.c: In function ‘bnx2_enable_forced_2g5’:
drivers/net/bnx2.c:1447: warning: ‘bmcr’ may be used uninitialized in this function
drivers/net/bnx2.c: In function ‘bnx2_disable_forced_2g5’:
drivers/net/bnx2.c:1482: warning: ‘bmcr’ may be used uninitialized in this function
One fix would be to have an initial value, but a plain return might be better.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the kernel api already has the macro "min",
just use it instead of declaring another one.
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ulp_type' is signed, make sure it is not negative
when we read the array element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't access netdev->stats in IO path. Save them in tx_ring/rx_rings
and add them up when get_stats API is called.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These sub-commands are issued by another (FCoE) function requesting
an operation on a shared resource.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inverted setting of 'retries'; when we are in the probe() path, we
should retry to enable the function only once; otherwise until it
times out.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The function was always setting the return value to the amount of
bytes transferred, overwriting the error code in error paths.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When the device stalls, clear it and retry; if it keeps failing too
often, reset the device.
This specially happens when running on virtual machines; the real
hardware doesn't seem to trip on stalls too much, except for a few
reports in the mailing list (still to be confirmed this is the cause,
although it seems likely.
NOTE: it is not clear if the URB has to be resubmitted fully or start
only at the offset of the first transaction sent. Can't find
documentation to clarify one end or the other.
Tests that just resubmit the whole URB seemed to work in my
environment.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The iwmc3200 has a quirk where retrying SDIO enable during the probe()
path causes bad interactions with the TOP function controller that
causes a reset storm. The workaround is simply not to retry an SDIO
enable in said path (and still do in the reset / reinitialization
paths).
The driver does so by checking i2400ms->debugfs_dentry to see if it
has been initialized; if not, it is in the probe() path. Document said
fact in i2400ms->debugfs_entry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Different paths of the i2400m SDIO driver need to take care of a few
SKU-specific quirks. For the ones that are common to to all the
iwmc3200 based devices, introduce i2400ms->iwmc3200 [set in
i2400ms_probe()], so it doesn't have to check against the list of
iwmc3200 SKU IDs on each quirk site.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The USB code was incorrectly specifiying timeouts to be in jiffies vs
msecs. On top of that, lower it to 200ms, as 1s is really too long
(doesn't allow the watchdog to trip a reset if the device timesout too
often).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m, when conected, will negotiate with the WiMAX basestation
to put the link in IDLE mode when it is not being used. Upon RX/TX
traffic, the link has to be restablished and that might require some
crypto handshakes and maybe a DHCP renew.
This process might take up to 20 (!) seconds and in some cases we were
seeing network watchdog warnings that weren't needed.
So the network watchdog timeout is updated to be slightly above that
20s threshold. As well, the driver itself will double check if the
device is stuck in IDLE mode -- if that happens, the device will be
reset (in this case the queue is also woken up to remove bogus--once
the device is reset--warnings).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Currently the i2400m driver was resetting by just calling
i2400m->bus_reset(). However, this was missing stopping the TX queue
and downing the carrier. This was causing, for the corner case of the
driver reseting a device that refuses to go out of idle mode, that a
few packets would be queued and more than one reset would go through,
making the recovery a wee bit messy.
To avoid introducing the same cleanup in all the bus-specific driver,
introduced a i2400m_reset() function that takes care of house cleaning
and then calling the bus-level reset implementation.
The bulk of the changes in all files are just to rename the call from
i2400m->bus_reset() to i2400m_reset().
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Some versions of the user space Intel WiMAX daemon need to have full
control over the device initialization sequence. By setting the module
option i2400.passive_mode to 1, the driver defers all device
configuration and initialization to user space.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
- TC35815_DMA_SYNC_ONDEMAND is always enabled.
- WORKAROUND_LOSTCAR is always enabled.
- WORKAROUND_100HALF_PROMISC is always enabled.
- GATHER_TXINT is always enabled.
- TC35815_USE_PACKEDBUFFER is always disabled.
- NO_CHECK_CARRIER is always disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides basic hash rules programming via the ethtool
interface.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces multiple group support for etsec2.0
devices.
Multiple group support is provided by mapping the set of enabled
queues to different groups and then programming the per group
regsiters imask, ievent, rstat, tstat.
The queues corresponding to a group are indicated by programming
isrg (interrupt steering) registers.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for etsec2.0 regsiters
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mdio support for etsec2.0 devices.
Modified the fsl_pq_mdio structure to include the new mdio
members.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces multiple Tx and Rx queues.
The incoming packets can be classified into different queues
based on filer rules (out of scope of this patch). The number
of queues enabled will be based on a DTS entries fsl,num_tx_queues
and fsl,num_rx_queues.
Although we are enabling multiple queues, the interrupt coalescing
is on per device level (etsec-1.7 doesn't support multiple rxics
and txics).
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the group structure. The elements of this
structure are the interrupt lines, their corresponding names,
the register memory map.
The elements for this group are factored out from the gfar_private
structure. The introduction of group structure will help in
providing support for newer versions of etsec.
Currently, the support is present only for single group and
single tx/rx queues.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces per tx and per rx queue structures.
Earlier the members of these structures were inside the
gfar_private structure.
Moving forward if we want to support multiple queues, we need
to refactor the gfar_private structure so that introduction of
multiple queues is easier.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.103.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to disable the TXC and RXC reference clocks if link
is not available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an RXC auto power-down feature to the code that supports
the gphys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5785 does not use the RXC reference clock. Turning it off is
desirable as it saves power.
By default, the 50610 enables the RXC reference clock and the 50610M
disables it. Presumably this is one of the reasons why the hardware
architect chose one over the other.
Adding a "rx reference clock disable" flag is not the ideal way to
describe the option, as it would force the MAC using a 50610M to set
the flag. Ideally we want the flags to represent opt-in behavior that
deviates from hardware defaults. Furthermore, the lack of a
"disable" flag implies that the requester wants the rx reference clock
enabled, which doesn't necessarily follow.
By presenting the option as a passive statement (rx reference clock
unused) rather than a command, I hope to convey an opt-in option to
disable the rx reference clock that falls back to hardware defaults if
not set. A secondary benefit of this is that it keeps the
intelligence about phy defaults in the broadcom module where it belongs
and allows the broadcom module more latitude should a bug arise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto power-down (APD) support is a power-saving feature. It should be
selectively enabled since it might expose MAC bugs. This patch changes
the code to enable APD only if the PHY_BRCM_AUTO_PWRDWN_ENABLE flag is
set. The tg3 driver was changed to set this bit.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom 50610M parts changed the default definitions of the RGMII mode
shadow register. The 5785 needs the RGMII mode selection bits [4:3]
cleared.
The default value of the remaining bits in this register are zero.
Rather than unnecessarily burn an extra bit in the dev_flags member in
an attempt to enumerate all possible combinations, this patch take a
more course grained approach and labels the option as "clear all bits".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves all the dev_flags enumerations outside the broadcom.c
file to include/linux/brcmphy.h. The existing flags were not used yet
and have been re-enumerated to avoid conflicts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 50610M phy ID for 5785.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a 50610 or 50610M is paired against particular remote partners,
link is slow to come up. This patch works around the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the code that requires the SMDSP clock to be
enabled into a single function that (hopefully) makes the dependency
obvious.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the loopback test timeout from 250 usec to 350 usec.
When the 5785 is paired against an AC131 phy, the older timeout is
just a little too close to the expected performance based on timings.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the port mode to MII when the link is down for the 5785.
Setting the port mode to MII instead of GMII saves power.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AC131 does not respect the power down bit (bit 11) of the MII
Control Register (reg 0x0). Instead, software is required to put the
phy into standby power down mode through the shadow register set. This
patch implements support for the AC131 standby power down mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves 5785 performance by allowing the write DMA engine to
request larger DMA burst sizes than it otherwise would.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to check the status of pci_map_single() before
allowing rx buffers to be used. It also converts the pci_map_single()
call in tg3_run_loopback() to use skb_dma_map() instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prevents a PCIe tx glitch by allowing the transmitter to go
to a low power state.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the PHY_ADDR preprocessor definition. The following
patch will identify a new member on the MDIO bus, so we want this
preprocessor definition to be a little more descriptive.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain power saving conditions, 57780 asic rev devices might
disappear from the system. The fix is to disallow the PCIe PLL from
powering down.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5906 has trouble with fragments that are less than 8 bytes in size.
This patch works around the problem by pivoting the 5906's transmit
routine to tg3_start_xmit_dma_bug() and introducing a new SHORT_DMA_BUG
flag that enables code to detect and react to the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a flag for each bug workaround in
tg3_start_xmit_dma_bug(). This is prep work for the following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Responses to firmware commands are read in by the command transmission
function, as part of command flow. Previously responses were read in
multiple places.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the endianness-handling of the firmware command result status handling
code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PSM entries can fail (transmitting the corresponding null-func may not
be heard by the AP.) Previously, this scenario was not detected, and
out-of-sync between STA and AP could occur.
Add retry implementation for the entries to recover from the situation.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the result code of all commands, and return an error code if the
firmware reports an error in execution. Previously this error would go
ignored in most cases.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, to avoid distortions, the TX power level has been hardcoded
to a low value. The value is slightly too low for good functionality, so
we increase it from 7dB to 12dB.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The null-data template (nullfunc) is dependent on the BSSID of the
current AP only, so it needs to be updated only when the BSSID changes.
Removed excess setting of the template.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report successful transmissions (receiver awake and on the same
channel) by generating ACK frames on the hwsim0 interface. This makes
it easier to figure out from packet capture logs whether frames were
delivered or not.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track the idle state for hwsim radios and reject TX if mac80211 is
trying to transmit something when the radio is supposed to be idle. In
addition, do not deliver frames if the receiving radio is in the idle
state.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
James Grossmann [1] reported that p54 spews out confusing
messages instead of preventing the mayhem from happening.
the reason is that "p54: generate channel list dynamically"
is not perfect. It didn't discard incomplete channel data
sets and therefore p54 advertised to support them as well.
[1]: http://marc.info/?l=linux-wireless&m=125699830215890
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: James Grossmann <cctsurf@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x50 series, it is wimax/wifi combo device, so driver need to enable
the wimax/wifi co-exist function and send the coexist event priority
table to uCode for operation.
The priority table will be used by uCode to determine what is the proper
action it should take when co-exist with WiMAX.
For example, when WiFi runs a scan, it must own radio exclusively, therefore
will disconnect WiMAX if WiMAX is connected.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spatial Multiplexing Power Save was disabled to achieve better
throughput while in power save mode by activating all the rx chains all the time.
By doing so, the device power consumption is high.
Enable static/dynamic spatial multiplexing power save if device support
it, which can lower the power consumption without impact throughput.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add data structure define for COEX_MEDIUM_NOTIFICATION and
COEX_EVENT_CMD host commands.
COEX_MEDIUM_NOTIFICATION is notification from uCode to host to indicate
medium changes. COEX_EVENT_CMD is from host to uCode for coex event
request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
More information than the "-EIO" return code will be useful here.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fits better in how the callbacks operate (alloc does allocation and
init does initialization). This also helps if we later want to do our own
initialization without relying on the mac80211 allocation.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the rate scale information is pointed to from the mac80211
station structure but since that is the only member we might as well make
it part of the structure. Also move the rate scaling initialization to the
init function, no need to do it when we allocate the structure. This fits
with how mac80211 deals with rate scaling information (it always calls init
after allocation) and makes it easier for us to later call initialization
directly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for some station management changes we split the addition of
a broadcast station from the other stations. Later we will rely on mac80211
to direct all management (addition/removal) of all stations except the
broadcast station.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since iwlagn is the only user of these functions, move it to this module.
This results in a bit more code moving than just these functions since the
functions only used by them are also moved and we need to export the
symbols previously available to them directly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling responses to driver originated commands include passing the
original command buffer to the caller. At this time it is possible for a
callback to be invoked that is passed this command buffer and thus likely
to access it.
We need to make sure that the memory associated with that buffer is not DMA
mapped at the time.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5. This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues. Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.
This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add/clarify comments and debug messages for interrupt used only for uCode load
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus.
Workaround disables L0S state so device moves directly from L0->L1.
Workaround needed on all devices since and including 4965; add to 6000/1000.
Describe bug and workaround better in comments.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To save power, don't run apm_ops.init() until needed at "up" time.
EEPROM (5000 and earlier devices) may be read without running apm_ops.init(),
but OTP reads (6000 and newer devices) require a powered-up chip.
Therefore, remove apm_ops.init() from the general path in XXXX_pci_probe(),
and call it only if device uses OTP. Once done with OTP read, call
apm_ops.stop() to reset chip and save power until "up" time comes around.
NOTE: This patch depends on removal of priv->lock from iwl_apm_stop();
lock does not get initialized until later in flow. See patch
"remove unneeded locks from apm_stop()".
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since priv->reg_lock was added to keep multi-access register manipulation
atomic, priv->lock protection is no longer needed. Remove this from
iwl_apm_stop_master() and iwl_apm_stop().
Add warning of timeout when polling for busmaster disablement confirmation,
and some comments.
NOTE: This is needed to enable use of apm_ops.stop() within iwl_eeprom_init();
priv->lock does not get initialized until after this flow. See patch
"remove power-wasting calls to apm_ops.init()"
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By setting the firmware version in wiphy it is possible to obtain this
information via ethtool. Some examples,
# ethtool -i wlan1
driver: iwlagn
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 228.57.2.23
bus-info: 0000:03:00.0
# ethtool -i wlan0
driver: iwl3945
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 15.28.2.8
bus-info: 0000:02:00.0
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the internal command and data buffers that the GSPI driver
maintained and instead relies on the Libertas core to synchronize access
to the command and data ports as with the other interface drivers. This
cleanup reduces the GSPI driver's memory footprint and should improve
performance by removing the need to copy to these internal buffers.
This also simplifies the bottom half of the interrupt handler.
This is an incremental cleanup: after removing the redundant buffers, we
can further improve the driver to use a threaded IRQ handler instead of
maintaining its own thread. However I would like a few folks to test
the buffer removal first and make sure that I'm not introducing
regressions.
Tested on Blackfin BF527 with DMA disabled due to an issue with the SPI
host controller driver in the current bleeding-edge Blackfin kernel. I
would appreciate it if someone with working DMA could test this patch
and provide feedback.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: George Shore <george.shore@imgtec.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change name on vlan_rx_add, kill, register to match other driver API.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_get_by_name_rcu() instead of dev_get_by_name(),
to avoid touching device refcount in hotpath.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add API Add k8695_get_rx_enable_bit() for get Rx interrupt
enable/status bit.
2. add some comment or document about some functions and variables.
3. update driver version to "1.02"
4. add napi_enable() and napi_disable() in open/close file method.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU throttle-down if a RNDIS device doesn't support a particular
packet size is being incorrectly logged. The attempted packet size is
being clobbered before it gets logged.
First patch; please inform if I'm doing this incorrectly. Diff'd
against latest official source as per the FAQ; forward port to current
git version is straightforward.
Signed-off-by: George Nassar <george.nassar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is adapted from the submission by Michael Buesch <mb@bu3sch.de>
for a bounce-buffer copying problem with b43.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check after the loop which checks whether the initialization timed-out
was wrong. If the initialization would succeed exactly in the 20000th time
(the value set for INIT_LOOP), the driver would bail out and claim that
initialization failed.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To do this we reorder callers in order in which they are called.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force bias is a fix for usage of AR5416 radios on the 2.4 GHz band
for orientation sensitivity. This was only partially implemented
with the ath9k_hw_decrease_chain_power() but first -- this was being
called for all chipsets which is not correct and second -- it was
missing the actual orientation code.
We now ensure to only enable force bias only for AR5416 and BUG_ON()
on other chipsets. Although ath9k_hw_decrease_chain_power() was enabled
for newer chipsets I suspect that it never ran unless the EEPROM had
ATH9K_ANT_FIXED_A or ATH9K_ANT_FIXED_B for antenna diversity.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This only differs between single-chip solutions and non single-chip
solutions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reorders phy.c routines in the order in the order in which they are used
and also moves the spur mitigation helpers for each type of chip into phy.c
as they are RF related.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids a branch on every channel change.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to later define a callback for both.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This clarifies this is only required for external radios.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is calling an allocation and checking for it, simplify
this process in a macro.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_rfattach() was just calling a helper and this helper was
doing nothing for single-chip devices, and for non single-chip devices
it is just allocating memory for banks to program the RF registers
at a later time. Simplify this by having the hw initialization call
the rf bank allocation directly for external radios.
Also, propagate an -ENOMEM properly now upon failure.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We a huge branch for old hardware and nothing for newer
hardware. Instead of doing this just bail out early for
newer hardware.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document what we can about the RF analog front ends (radios)
of Atheros 802.11n devices. What should be clearer now is the
what we do for old pre AR5416 and AR5418 MAC based devices in
comparison to the modern sigle-chip 802.11n solutions.
All devices after AR9280 are single chip and require less
programming -- the RF registers no longer need to be initialized
as they all have the RF analog front end embedded together with
the MAC/BB; this includes the AR9271. Older devices such as the
ones with the AR5416 MACs (PCI) or AR5418 MACs (PCI-E) have an
external 2.4 GHz AR2133 radio or a dual band 2.4 GHz / 5 GHz
AR5133 radio. These external radios require additional programming
of the RF registers.
Clarify which parts are for what devices and which code is
shared. This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We adjust the core clock for ar9271 to 117 MHz; this also
requires us to adjust the baud divider based on the targetted
baud rate.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This update the register initialization/reset values (aka initvals)
for ar9271 based on the last recommended values on 2009-06-04 by our
systems engineering team.
The changes account for:
* Supporting ar9271 1.0 and ar9271 1.1 together, the difference
is bb_spectral_scan_ena, for 1.0 we'll set this to 0x1.
* Ensuring we get the correct noise floor values -115 ~ -118
when we enable bb_enable_ant_div_lnadiv=0 and
mc_tx_def_ant_sel=1. Previous to this we would get noise
floor values in the range -50 ~ -80. To fix settings for
the registers:
- bb_ch1_xatten1_db
- bb_ch1_xatten2_db
- bb_ch1_xatten1_margin
- bb_ch1_xatten2_margin
- bb_ch1_gain_force
- bb_ch1_xatten2_hyst_margin
- bb_ch1_xatten1_hyst_margin
- bb_ch1_max_oc_gain
* 0x8120[2] mc_mic_new_location_enable is changed to 0x1. The MAC team
suggest to set this value.
* 0x9910[0] bb_spectral_scan_ena is changed to 0x0.
For ar9271 1.1 we don't need to enable this bit.
Cc: Stephen Chen <Stephen.Chen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the WLAN_PRE80211 drivers moved to drivers/staging, this
distinction becomes unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the netwave driver to drivers/staging. This is another pre-802.11
driver that has seen virtually no non-API-fixup activity in years, and
for which no active hardware is likely to still exist. This driver
represents unnecessary ongoing maintenance for no clear benefit.
This patch brought to you by the "hacking" session at the 2009 Kernel
Summit in Tokyo, Japan...
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the wavelan driver to drivers/staging. This is another pre-802.11
driver that has seen virtually no non-API-fixup activity in years, and
for which no active hardware is likely to still exist. This driver
represents unnecessary ongoing maintenance for no clear benefit.
This patch brought to you by the "hacking" session at the 2009 Kernel
Summit in Tokyo, Japan...
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the arlan driver to drivers/staging. This is another pre-802.11
driver that has seen virtually no non-API-fixup activity in years, and
for which no active hardware is likely to still exist. This driver
represents unnecessary ongoing maintenance for no clear benefit.
This patch brought to you by the "hacking" session at the 2009 Kernel
Summit in Tokyo, Japan...
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the strip ("Starmode Radio IP") driver to drivers/staging. For
several years this driver has only seen API "bombing-run" changes, and
few people ever had the hardware. This driver represents unnecessary
ongoing maintenance for no clear benefit.
This patch brought to you by the "hacking" session at the 2009 Kernel
Summit in Tokyo, Japan...
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While there may be a case for a driver adding its
own bits of radiotap information, none currently
does. Also, drivers would have to copy the code
to generate the radiotap bits that now mac80211
generates. If some driver in the future needs to
add some driver-specific information I'd expect
that to be in a radiotap vendor namespace and we
can add a different way of passing such data up
and having mac80211 include it.
Additionally, rename IEEE80211_CONF_RADIOTAP to
IEEE80211_CONF_MONITOR since it's still used by
b43(legacy) to obtain per-frame timestamps.
The purpose of this patch is to simplify the RX
code in mac80211 to make it easier to add paged
skb support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This buglet confused me a lot just now ...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An extra register was being written to for PA calibration
making the hardware unresponsive, remove it. Hardware
reset should now complete fine on ar9271.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We had 0x9912 but AR_PHY_SPECTRAL_SCAN is 0x9910. By using the
0x9912 we were making the hardware unresponsive. This allows us
to move forward with hardware reset on ar9271 on the ath9k_htc
driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices with external radios have revisions which we can count on.
On single chip solutions these EEPROM values for these radio revision
also exist but are not meaningful as the radios are embedded onto the
same chip. Each single-chip device evolves together as one device.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are shared between ath9k and the future ath9k_htc driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 supports power save and it can be enabled now.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the following calibration functions:
-Set TX IQCC
-Set TX Power by Index
-PR41573 workaround (incomplete, needs PHY reset)
-Calc RX IQ Comp
-PHY Cordic
-Run Samples
-Start/Stop TX Tone
-part of PAPD Cal TX Power
-RX I/Q Calibration
-The basic structure of the periodic calibration wrapper
Software RFKILL (required by calibration) is also implemented in
this round.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a 64-bit kernel, skb->tail is an offset, not a pointer. The libertas
usb driver passes it to usb_fill_bulk_urb() anyway, causing interesting
crashes. Fix that by using skb->data instead.
This highlights a problem with usb_fill_bulk_urb(). It doesn't notice
when dma_map_single() fails and return the error to its caller as it
should. In fact it _can't_ currently return the error, since it returns
void.
So this problem was showing up only at unmap time, after we'd already
suffered memory corruption by doing DMA to a bogus address.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch e43419f9:
ath9k: downgrade assert in rc.c for invalid rate
downgraded an ASSERT to a WARN_ON() but also misplaced a
semicolon at the end of the second check. What this did
was force the rate control code to always return the rate
even if we should have warned about it. Since this should
not have happened anymore anyway this fix isn't critical
as the proper rate would have been returned anyway.
Cc: stable@kernel.org
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43 allocates a bouncebuffer, if the supplied TX skb is in an invalid
memory range for DMA.
However, this is broken in that it fails to copy over some metadata to the
new skb.
This patch fixes three problems:
* Failure to adjust the ieee80211_tx_info pointer to the new buffer.
This results in a kmemcheck warning.
* Failure to copy the skb cb, which contains ieee80211_tx_info, to the new skb.
This results in breakage of various TX-status postprocessing (Rate control).
* Failure to transfer the queue mapping.
This results in the wrong queue being stopped on saturation and can result in queue overflow.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For non-monitor interfaces, the syntax for alloc_ieee80211/free_80211
is wrong. Because alloc_ieee80211 only creates (wiphy_new) a wiphy, but
free_80211() does wiphy_unregister() also. This is only correct when
the later wiphy_register() is called successfully, which apparently
is not the case for your fw doesn't exist one.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Don't call rtnl_link_unregister if rtnl_link_register fails
- Set .priv_size so we aren't stomping on uninitialized memory
when we use netdev_priv, on bond devices created with
ip link add type bond.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a basic set of rtnl link ops and takes advantage of
the fact that rtnl_link_unregister kills all of the surviving
devices to all us to kill bond_free_all. A module alias
is added so ip link add can pull in the bonding module.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manually inline the code from bond_deinit to bond_uninit. bond_uninit
is the only caller and it is short.
Move the call of bond_release_all from the netdev notifier into
bond_uninit. The call site is effectively the same and performing
the call explicitly allows all the paths for destroying a
bonding device to behave the same way.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop calling dev_get_by_name to see if the bond device already
exists. register_netdevice already does that.
Stop calling bond_deinit if register_netdevice fails as bond_uninit
is guaranteed to be called if bond_init succeeds.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch delegates the work of creating the sysfs groups
to the netdev layer and ultimately to the device layer. This
closes races between uevents.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before bringing up a sky2 interface up ethtool reports
"Link detected: yes". Do as ixgbe does and netif_carrier_off() on
probe().
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 23289a37e2
(net: add a list_head parameter to dellink() method),
I forgot to actually use this parameter in veth_dellink.
I remember feeling a bit uncomfortable about veth_close(),
because it does :
netif_carrier_off(dev);
netif_carrier_off(priv->peer);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For USB 3.0 it is necessary that all drivers use the standard
API to reset a configuration. This removes a home-grown
implementation.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Hi David,
please take this for the next merge window.
Regards
Oliver
Signed-off-by: David S. Miller <davem@davemloft.net>
Tentative support for newer Marvell hardware including
the Yukon-2 Optima chip. Do not have hatdware to test this yet,
code is based on vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes related to support of Yukon supreme chip.
Don't have this chip version to test on,
these are reverse engineered from the vendor (GPL) driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program the receive pause thresholds differently depending on
chip version. This cloned from from the vendor (GPL) driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds infrastructure for the newer chip versions and workarounds.
Extracted from the vendor (GPL) driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new ID that just showed up in latest vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of PreMax ethernet pcmcia card,
and some Sierra Wireless serial card(AC555, AC7xx, AC8xx).
use PROD_ID for AC7xx, because MANF_ID of AC7xx and AC8xx are the same.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8169 card drop incoming VLAN tagged MTU byte large jumbo frames
It looks to compare current and maximal packet sizes hardware use
'<' operator, not '<='.
Bug introduced by commit fdd7b4c330
("r8169: fix crash when large packets are received")
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected. The original version of this
workaround was found to be incomplete.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead. This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change in how PHYs are electrically isolated caused all PHYs to be
isolated followed by reverting that isolation for the selected PHY.
Unfortunately, isolating the selected PHY for even a short period of
time can result in DHCP negotiation taking more than 10 seconds on certain
embedded configurations delaying boot time as reported by Bernhard Kaindl.
This patch reverts the change to how PHYs are isolated yet still works
around the issue for 82552 needing the selected PHY's BMCR register to
be written after the unused PHYs are isolated. This code is moved below
the setting of nic->phy ID in order to do the 82552-specific workaround.
Cc: Bernhard Kaindl <bernhard.kaindl@gmx.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can tell whether GRO is being applied, this heuristic is
effective once more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GRO is successfully merging received packets, we should allocate
raw page buffers rather than skbs that will be discarded by GRO.
Otherwise, we should allocate skbs.
GRO also benefits from higher interrupt moderation, so increase the
score for mergeable RX packets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
net: Fix 'Re: PACKET_TX_RING: packet size is too long'
netdev: usb: dm9601.c can drive a device not supported yet, add support for it
qlge: Fix firmware mailbox command timeout.
qlge: Fix EEH handling.
AF_RAW: Augment raw_send_hdrinc to expand skb to fit iphdr->ihl (v2)
bonding: fix a race condition in calls to slave MII ioctls
virtio-net: fix data corruption with OOM
sfc: Set ip_summed correctly for page buffers passed to GRO
cnic: Fix L2CTX_STATUSB_NUM offset in context memory.
MAINTAINERS: rt2x00 list is moderated
airo: Reorder tests, check bounds before element
mac80211: fix for incorrect sequence number on hostapd injected frames
libertas spi: fix sparse errors
mac80211: trivial: fix spelling in mesh_hwmp
cfg80211: sme: deauthenticate on assoc failure
mac80211: keep auth state when assoc fails
mac80211: fix ibss joining
b43: add 'struct b43_wl' missing declaration
b43: Fix Bugzilla #14181 and the bug from the previous 'fix'
rt2x00: Fix crypto in TX frame for rt2800usb
...
I've not touched the other stuff here but the word "locking" comes to mind.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up driver resources without touch the hardware. Add pci
save/restore state.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PCI IDs for the next generation chip to the
PCI_DEVICE_ID table.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing flow control (pause) parameters, the flow control thresholds
(i.e. when to send XON/XOFF frames) may not be setup correctly on parts
with copper media. Call the existing e1000_set_fc_watermarks()
function to set these thresholds.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the netdev_ops.ndo_fcoe_get_wwn in 82599 if it finds valid
prefix for the World Wide Node Name (WWNN) or World Wide Port Name (WWPN),
as well as valid SAN MAC address.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82599 EEPROM supports alternative prefix for World Wide Node Name
(WWNN) and World Wide Port Name (WWPN). The prefixes can be used together
with the SAN MAC address to form the WWNN and WWPN, which can be used by
upper layer drivers such as Fiber Channel over Ethernet (FCoE).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate headerfile includes from vmxnet3_int.h
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mii monitor mode, bond_check_dev_link() calls the the ioctl
handler of slave devices. It stores the ndo_do_ioctl function
pointer to a static (!) ioctl variable and later uses it to call the
handler with the IOCTL macro.
If another thread executes bond_check_dev_link() at the same time
(even with a different bond, which none of the locks prevent), a
race condition occurs. If the two racing slaves have different
drivers, this may result in one driver's ioctl handler being
called with a pointer to a net_device controlled with a different
driver, resulting in unpredictable breakage.
Unless I am overlooking something, the "static" must be a
copy'n'paste error (?).
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ethtool get_settings function to:
- get current link speed settings from controller
- get port transceiver type from controller
- fill appropriate values for supported, phy_address
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
