I noticed that the VT switch doesn't work any longer with a Dell
laptop with 1366x768 eDP when the machine is connected with a DP
monitor. It behaves as if VT were switched, but the graphics remain
frozen. Actually the keyboard works, so I could switch back to VT7
again.
I tried to track down the problem, and encountered a long story until
we reach to this error:
- The machine is booted with video=1366x768 option (the distro
installer seems to add it as default).
- Recently, drm_helper_probe_single_connector_modes() deals with
cmdline modes, and it tries to create a new mode when no
matching mode is found.
- The drm_mode_create_from_cmdline_mode() creates a mode based on
either CVT of GFT according to the given cmdline mode; in our case,
it's 1366x768.
- Since both CVT and GFT can't express the width 1366 due to
alignment, the resultant mode becomes 1368x768, slightly larger than
the given size.
- Later on, the atomic commit is performed, and in
drm_atomic_check_only(), the size of each plane is checked.
- The size check of 1366x768 fails due to the above, and eventually
the whole VT switch fails.
Back in the history, we've had a manual fix-up of 1368x768 in various
places via c09dedb7a5 ("drm/edid: Add a workaround for 1366x768 HD
panel"), but they have been all in drm_edid.c at probing the modes
from EDID. For addressing the problem above, we need a similar hack
to the mode newly created from cmdline, manually adjusting the width
when the expected size is 1366 while we get 1368 instead.
Fixes: eaf99c749d ("drm: Perform cmdline mode parsing during...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109145614.29454-1-tiwai@suse.de
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
This reverts commit 6dffd431e2.
Adding new mode flags willy nilly breaks existing userspace. We need to
coordinate this better, potentially with a new client cap that only
exposes the aspect ratio flags when userspace is prepared for them
(similar to what we do with stereo 3D modes).
This also broke things so that we would always send out VIC==0 in
the AVI infoframe unless the user specified an aspect ratio via
the mode flags. And the automagic RGB full vs. limited range
handling was similartly broken as the user mode would never match
any CEA mode.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Lin, Jia <lin.a.jia@intel.com>
Cc: Akashdeep Sharma <akashdeep.sharma@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1478176304-6743-2-git-send-email-ville.syrjala@linux.intel.com
This reverts commit a68362fe3e.
Adding new mode flags willy nilly breaks existing userspace. We need to
coordinate this better, potentially with a new client cap that only
exposes the aspect ratio flags when userspace is prepared for them
(similar to what we do with stereo 3D modes).
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Lin, Jia <lin.a.jia@intel.com>
Cc: Akashdeep Sharma <akashdeep.sharma@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1478176304-6743-1-git-send-email-ville.syrjala@linux.intel.com
We have reached the era where monitor bandwidths now exceed 31bits in
frequency calculations, though as we stored them in kHz units we are
safe from overflow in the modelines for some time.
[ 48.723720] UBSAN: Undefined behaviour in ../drivers/gpu/drm/drm_modes.c:325:49
[ 48.726943] signed integer overflow:
[ 48.728503] 2240 * 1000000 cannot be represented in type 'int'
Reported-by: Martin Liška <marxin.liska@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98372
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161021141540.26837-1-chris@chris-wilson.co.uk
HDMI 2.0/CEA-861-F introduces two new aspect ratios:
- 64:27
- 256:135
This patch:
- Adds new DRM flags for to represent these new aspect ratios.
- Adds new cases to handle these aspect ratios while converting
from user->kernel mode or vise versa.
V2: Rebase
V3: Align macro for DRM_MODE_PICTURE_ASPECT_256_135 (Jim Bride)
V4: Added r-b from Jose.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1476705880-15600-5-git-send-email-shashank.sharma@intel.com
Current DRM layer functions don't parse aspect ratio information
while converting a user mode->kernel mode or vice versa. This
causes modeset to pick mode with wrong aspect ratio, eventually
causing failures in HDMI compliance test cases, due to wrong VIC.
This patch adds aspect ratio information in DRM's mode conversion
and mode comparision functions, to make sure kernel picks mode
with right aspect ratio (as per the VIC).
V2: Addressed review comments from Sean:
- Fix spellings/typo
- No need to handle aspect ratio none
- Add a break, for default case too
V3: Rebase
V4: Added r-b from Jose
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Lin, Jia <lin.a.jia@intel.com>
Signed-off-by: Akashdeep Sharma <akashdeep.sharma@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1476705880-15600-3-git-send-email-shashank.sharma@intel.com
The 'de-active' and 'pixelclk-active' DT properties are evaluated
by of_parse_display_timing() called from of_get_drm_display_mode(),
but later lost in the conversion from videomode.flags to
drm_display_mode.flags.
Enhance of_get_drm_display_mode() to also return the bus flags in a
separate variable, so that they can be passed on to the ipu-di
driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
add a helper function to extract information about pixel clock and DE
polarity from DT for use by of_get_drm_display_mode().
While at it, convert spaces to tabs in indentation in drm_modes.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
As promised, piles of prep work all around:
- drm_atomic_state rework, prep for nonblocking commit helpers
- fence patches from Gustavo and Christian to prep for atomic fences and
some cool work in ttm/amdgpu from Christian
- drm event prep for both nonblocking commit and atomic fences
- Gustavo seems on a crusade against the non-kms-native version of the
vblank functions.
- prep work from Boris to nuke all the silly ->best_encoder
implementations we have (we really only need that for truly dynamic
cases like dvi-i vs dvi-d or dp mst selecting the right transcoder on
intel)
- prep work from Laurent to rework the format handling functions
- and few small things all over
* tag 'topic/drm-misc-2016-06-07' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm/dsi: Implement set tear scanline
drm/fb_cma_helper: Implement fb_mmap callback
drm/qxl: Remove useless drm_fb_get_bpp_depth() call
drm/ast: Remove useless drm_fb_get_bpp_depth() call
drm/atomic: Fix remaining places where !funcs->best_encoder is valid
drm/core: Change declaration for gamma_set.
Documentation: add fence-array to kernel DocBook
drm/shmobile: use drm_crtc_vblank_{get,put}()
drm/radeon: use drm_crtc_vblank_{get,put}()
drm/qxl: use drm_crtc_vblank_{get,put}()
drm/atmel: use drm_crtc_vblank_{get,put}()
drm/armada: use drm_crtc_vblank_{get,put}()
drm/amdgpu: use drm_crtc_vblank_{get,put}()
drm/virtio: use drm_crtc_send_vblank_event()
drm/udl: use drm_crtc_send_vblank_event()
drm/qxl: use drm_crtc_send_vblank_event()
drm/atmel: use drm_crtc_send_vblank_event()
drm/armada: use drm_crtc_send_vblank_event()
drm/doc: Switch to sphinx/rst fixed-width quoting
drm/doc: Drop kerneldoc for static functions in drm_irq.c
...
Just fallout from switching from asciidoc to sphinx/rst.
v2: Found more. Also s/\//#/ in the vgpu ascii-art - sphinx treats
those as comments and switch to variable-width, which wreaks the
layout.
v3: Undo some of the hacks, rebasing onto latest version of Jani's
series fixed it.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Mostly this is unexpected indents. But really it's just a
demonstration for my patch, all these issues have been found&fixed
using the correct source file and line number support I just added.
All line numbers have been perfectly accurate.
One issue looked a bit fishy in intel_lrc.c, where I don't quite grok
what sphinx is unhappy about. But since that file looks like it has
never seen a proper kernel-doc parser I figured better to fix in a
separate path.
v2: Use fancy new &drm_device->struct_mutex linking (Jani).
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When setting mode via MODE_ID property,
drm_atomic_set_mode_prop_for_crtc() does not call
drm_mode_set_crtcinfo() which possibly causes:
"[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 32: Can't
calculate constants, dotclock = 0!"
Whether the error is seen depends on the previous data in state->mode,
as state->mode is not cleared when setting new mode.
This patch adds drm_mode_set_crtcinfo() call to
drm_mode_convert_umode(), which is called in both legacy and atomic
paths. This should be fine as there's no reason to call
drm_mode_convert_umode() without also setting the crtc related fields.
drm_mode_set_crtcinfo() is removed from the legacy drm_mode_setcrtc() as
that is no longer needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This changes the code to handle being called multiple times without
side effects. The new names seems more suitable for what it does.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DRM Docbook is now Markdown ready. This means its doc is able to
use markdown text on it.
* Documentation/DocBook/drm.tmpl: Contains a table duplicated from
drivers/gpu/drm/i915/i915_reg.h. This is not needed anymore
* drivers/gpu/drm/drm_modeset_lock.c: had a code example that used
to look pretty bad on html. Fixed by using proper code markup.
* drivers/gpu/drm/drm_prime.c: Remove spaces between lines to make
a proper markup list.
* drivers/gpu/drm/i915/i915_reg.h: Altought pandoc supports tables,
it doesn't support table cell spanning. But we can use fixed-width
for those special cases.
* include/drm/drm_vma_manager.h: Another code example that should be
proper indented with four spaces.
v2 (Daniel): Adjust name to gpu.xml due to rename.
v3 (Daniel):
Split out the actual enabling in the Makefile - this way we can merge
the conversion, while just keeping the enabling in a drm-private tree.
Signed-off-by: Danilo Cesar Lemes de Paula <danilo.cesar@collabora.co.uk> (v1)
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448471279-19748-2-git-send-email-daniel.vetter@ffwll.ch
My latest commit introduce some case where a valid mode, could be
rejected.
simple_strtox functions stop at first non-digit character, but kstrtox
not.
So args like "video=HDMI-A-1:720x480-16@60" will be reject when checking
16@.
Discussions about this change comes to the conclusion that the best
solution is to revert my commit cc344980c7.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449838739-29969-1-git-send-email-clabbe.montjoie@gmail.com
Now that the mode type bit merge logic is fixed to only merge
between new probed modes, hopefully we can eliminat the special
case for qxl and virtio. That is make the merge the mode type
bits from all matching new probed modes, just like every other
driver.
qxl and virtio got excluded from the merging in
commit 3fbd6439e4 ("drm: copy mode type in drm_mode_connector_list_update()")
commit abce1ec9b0 ("Revert "drm: copy mode type in drm_mode_connector_list_update()"")
commit b87577b7c7 ("drm: try harder to avoid regression when merging mode bits")
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflicts with doc updates.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently most drivers request that any mode appearing on both the
old mode list and the new probed_modes list get their type bits ORed
together if the modes are deemed to otherwise match each other.
I don't know why anyone would want to merge in the mode type bits
from any mode left over from a previous probe. For instance, you
could never get rid of ther preferred bit if a matching non-preferred
mode is returned by the new probe. So let's not merge anything from
the stale old modes, and just replace them outright with matching new
modes.
If multiple matching modes are produced by the same probe, merging
the type bits between them would seem like a sensible thing to do.
For a bit of extra finesse if two modes are considered equal we can
pick the actual timings from the one marked as preferrred. And if
multiple preferred modes are produced by the same probe somehow, we
can just favor the first one added to the probed_modes list.
You may be asking yourself why we bother with the merging at all if
nothing from the old list survives in practice. The only answer I have
is "debug output". That is we want to print out a list of pruned modes,
which is why we still want to look for duplicates with the old modes.
There was a previous attempt to get rid of the mode type merging
entirely, but it caused some kind of regression on Daniels's G33
machine. Apparently the sdvo transcoder on said machine started to
die at around the same time and has since rotted away totally, so
it may have been a red herring. So we don't have to worry about
it anymore. The relevant commits are:
commit 3fbd6439e4 ("drm: copy mode type in drm_mode_connector_list_update()")
commit abce1ec9b0 ("Revert "drm: copy mode type in drm_mode_connector_list_update()"")
It was then decided in
commit b87577b7c7 ("drm: try harder to avoid regression when merging mode bits")
that just qxl virtio are excluded from the merging, while everyone
else does it. That is not changed, although now even qxl and virtio
will be subject to the previously mentioned logic to choose which
actual timings are picked for the new mode.
v2: Fix typos in commit message, and clarify the details on
the G33 regression from the previous attempt (Daniel)
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449234781-22332-1-git-send-email-ville.syrjala@linux.intel.com
MODE_UNVERIFIED actually means that the mode came from a previous probe,
and if the new probe doesn't produce a matching mode it will get pruned
from the list. Rename the flag to MODE_STALE to better convey the
meaning.
v2: Rebased due to conflicts with Daniel's doc stuff
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449779948-10906-1-git-send-email-ville.syrjala@linux.intel.com
This was in the documentation for modeset helper hooks, where it is a
bit misplaced.
v2: Reindent the drm_mode_status enum, inspired by Ville.
v3: Suggestions from Ville and Thierry.
v4: Small fixup that 0day spotted.
v5: Slight change to avoid accidental headings in kerneldoc output.
Cc: ville.syrjala@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-27-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Reviewed-by: Thierry Reding <treding@nvidia.com> (v3)
Rather than using drm_match_cea_mode() to see if the EDID detailed
timings are supposed to represent one of the CEA/HDMI modes, add a
special version of that function that takes in an explicit clock
tolerance value (in kHz). When looking at the detailed timings specify
the tolerance as 5kHz due to the 10kHz clock resolution limit inherent
in detailed timings.
drm_match_cea_mode() uses the normal KHZ2PICOS() matching of clocks,
which only allows smaller errors for lower clocks (eg. for 25200 it
won't allow any error) and a bigger error for higher clocks (eg. for
297000 it actually matches 296913-297000). So it doesn't really match
what we want for the fixup. Using the explicit +-5kHz is much better
for this use case.
Not sure if we should change the normal mode matching to also use
something else besides KHZ2PICOS() since it allows a different
proportion of error depending on the clock. I believe VESA CVT
allows a maximum deviation of .5%, so using that for normal mode
matching might be a good idea?
Cc: Adam Jackson <ajax@redhat.com>
Tested-by: nathan.d.ciobanu@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92217
Fixes: fa3a7340ea ("drm/edid: Fix up clock for CEA/HDMI modes specified via detailed timings")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The simple_strtoul function is marked as obsolete.
This patch replace it by kstrtouint.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the drm_display_mode <-> drm_mode_modeinfo conversion functions
from drm_crtc.c to drm_modes.c, and make them non-static so that others
can use them.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we're now using mode == NULL to represent disabled, it's not
wholly surprising that we'd want to compare NULL modes.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change 'pixes' to 'pixels'
Change 'enabel' to 'enable'
Change 'enabeling' to 'enabling'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently when a mode is rejected the reason is printed as a raw number.
Having to manually decode that to a enum drm_mode_status value is
tiresome. Have the code do the decoding instead and print the result
in a human readable format.
Just having an array of strings indexed with the mode status doesn't
work since the enum includes negative values. So we offset the status
by +3 which makes all the indexes non-negative. Also add a bit of
paranoia into the code to catch out of bounds accesses in case
someone adds more enum values but forgets to update the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Implement mode_fixup for a DI vertical timing limitation
- Use generic DRM OF helpers in DRM core
- Convert imx-hdmi to dw_hdmi drm_bridge and add rockchip
driver
- Add DC use counter to fix multi-display support
- Simplify handling of DI clock flags
- A few small fixes and cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r9/P
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2015-01-09' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm mode fixup support, imx-hdmi bridge conversion and imx-drm cleanup
- Implement mode_fixup for a DI vertical timing limitation
- Use generic DRM OF helpers in DRM core
- Convert imx-hdmi to dw_hdmi drm_bridge and add rockchip
driver
- Add DC use counter to fix multi-display support
- Simplify handling of DI clock flags
- A few small fixes and cleanup
* tag 'imx-drm-next-2015-01-09' of git://git.pengutronix.de/git/pza/linux: (26 commits)
imx-drm: core: handling of DI clock flags to ipu_crtc_mode_set()
gpu: ipu-di: Switch to DIV_ROUND_CLOSEST for DI clock divider calc
gpu: ipu-v3: Use videomode in struct ipu_di_signal_cfg
imx-drm: encoder prepare/mode_set must use adjusted mode
imx-drm: ipuv3-crtc: Implement mode_fixup
drm_modes: add drm_display_mode_to_videomode
gpu: ipu-di: remove some non-functional code
gpu: ipu-di: Add ipu_di_adjust_videomode()
drm: rockchip: export functions needed by rockchip dw_hdmi bridge driver
drm: bridge/dw_hdmi: request interrupt only after initializing the mutes
drm: bridge/dw_hdmi: add rockchip rk3288 support
dt-bindings: Add documentation for rockchip dw hdmi
drm: bridge/dw_hdmi: add function dw_hdmi_phy_enable_spare
drm: bridge/dw_hdmi: clear i2cmphy_stat0 reg in hdmi_phy_wait_i2c_done
drm: bridge/dw_hdmi: add mode_valid support
drm: bridge/dw_hdmi: add support for multi-byte register width access
dt-bindings: add document for dw_hdmi
drm: imx: imx-hdmi: move imx-hdmi to bridge/dw_hdmi
drm: imx: imx-hdmi: split phy configuration to platform driver
drm: imx: imx-hdmi: convert imx-hdmi to drm_bridge mode
...
- plane handling refactoring from Matt Roper and Gustavo Padovan in prep for
atomic updates
- fixes and more patches for the seqno to request transformation from John
- docbook for fbc from Rodrigo
- prep work for dual-link dsi from Gaurav Signh
- crc fixes from Ville
- special ggtt views infrastructure from Tvrtko Ursulin
- shadow patch copying for the cmd parser from Brad Volkin
- execlist and full ppgtt by default on gen8, for testing for now
* tag 'drm-intel-next-2014-12-19' of git://anongit.freedesktop.org/drm-intel: (131 commits)
drm/i915: Update DRIVER_DATE to 20141219
drm/i915: Hold runtime PM during plane commit
drm/i915: Organize bind_vma funcs
drm/i915: Organize INSTDONE report for future.
drm/i915: Organize PDP regs report for future.
drm/i915: Organize PPGTT init
drm/i915: Organize Fence registers for future enablement.
drm/i915: tame the chattermouth (v2)
drm/i915: Warn about missing context state workarounds only once
drm/i915: Use true PPGTT in Gen8+ when execlists are enabled
drm/i915: Skip gunit save/restore for cherryview
drm/i915/chv: Use timeout mode for RC6 on chv
drm/i915: Add GPGPU_THREADS_DISPATCHED to the register whitelist
drm/i915: Tidy up execbuffer command parsing code
drm/i915: Mark shadow batch buffers as purgeable
drm/i915: Use batch length instead of object size in command parser
drm/i915: Use batch pools with the command parser
drm/i915: Implement a framework for batch buffer pools
drm/i915: fix use after free during eDP encoder destroying
drm/i915/skl: Skylake also supports DP MST
...
Add conversion from drm_display_mode to videomode.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Make sure the timings of probed modes at least pass some very basic
sanity checks.
The checks include:
- clock,hdisplay,vdisplay are non zero
- sync pulse fits within the blanking period
- htotal,vtotal are big enough
I have not checked all the drivers to see if the modes the generate
might violate these constraints. I'm hoping not, because that would mean
either abandoning the idea of doing this from the core code, or fixing
the drivers.
I'm not entirely sure about limiting the sync pulse to the blanking
period. Intel hardware doesn't support such things, but some other
hardware might. However at least HDMI doesn't allow having sync pulse
edges within the active period, so I'm thinking the check is probably
OK to have in the common code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make drm_mode_validate_size() and drm_mode_validate_flag() deal with a
single mode instead of having each iterate through the mode list.
The hope is that in the future we might be able to share various mode
validation functions between modeset and get_modes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to get hdisplay and vdisplay in a few places so create a
helper to make our job easier.
Note that drm_crtc_check_viewport() and intel_modeset_pipe_config() were
previously making adjustments for doublescan modes and vscan > 1 modes,
which was incorrect. Using our new helper fixes this mistake.
v2 (by Matt): Use new stereo doubling function (suggested by Ville)
v3 (by Matt):
- Add missing kerneldoc (Daniel)
- Use drm_mode_copy() (Jani)
v4 (by Matt):
- Drop stereo doubling function again; add 'stereo only' flag
to drm_mode_set_crtcinfo() instead (Ville)
v5 (by Matt):
- Note behavioral change in drm_crtc_check_viewport() and
intel_modeset_pipe_config(). (Ander)
- Describe new adjustment flags in drm_mode_set_crtcinfo()'s
kerneldoc. (Ander)
Cc: dri-devel@lists.freedesktop.org
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fix spelling typos found in drm.xml.
It is because the file is generated from comments in
source codes, I have to fix the typos within source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915.ko has a custom fbdev initialisation routine that aims to preserve
the current mode set by the BIOS, unless overruled by the user. The
user's wishes are determined by what, if any, mode is specified on the
command line (via the video= parameter). However, that command line mode
is first parsed by drm_fb_helper_initial_config() which is called after
i915.ko's custom initial_config() as a fallback method. So in order for
us to honour it, we need to move the cmdline parser earlier. If we
perform the connector cmdline parsing as soon as we initialise the
connector, that cmdline mode and forced status is then available even if
the fbdev helper is not compiled in or never called.
We also then expose the cmdline user mode in the connector mode lists.
v2: Rebase after connector->name upheaval.
v3: Adapt mga200 to look for the cmdline mode in the new place. Nicely
simplifies things while at that.
v4: Fix checkpatch.
v5: Select FB_CMDLINE to adapt to the changed fbdev patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73154
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Cc: dri-devel@lists.freedesktop.org
Cc: Julia Lemire <jlemire@matrox.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For QXL hw we really want the bits to be replaced as we change
the preferred mode on the fly, and the same goes for virgl when
I get to it, however the original fix for this seems to have caused
a wierd regression on Intel G33 that in a stunning display of failure
at opposition to his normal self, Daniel failed to diagnose.
So we are left doing this, ugly ugly ugly ugly, Daniel you fixed
that G33 yet?, ugly, ugly.
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Tune down yelling RETURNS.
- OCD align all the parameters the same.
- Add missing kerneldoc, which also means that we need to include the
kerneldoc from the drm_modes.h header now.
- Add missing Returns: sections.
- General polish and clarification - especially the kerneldoc for the
mode creation helpers seems to have been some good specimen of
copypasta gone wrong.
All actual code changes have all been extracted into prep patches
since there was simply too much to polish.
v2: More polish for the command line modeline functions.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Totally unused and actually redundant with maxX for display mode
validation. The fb helper otoh needs to check pitch limits,
but that is delegated into drivers instead.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It never fails and no one ever checked anyway.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's a neat FIXME asking whether this is really need. I'd
say really no.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to also include kerneldoc from the header (for static inline
functions and structs), but fishing the right pieces out of a giant
header is a real pain. So split things out.
Note that it's not a really clean header with sane include orders, but
given's drm historical knack for giant headers detangling this is a
major task.
v2: Also extract struct drm_cmdline_mode.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Makes more sense and gives better grouping in the DocBook function
reference sections. To make this possible we need to expose two
functions from drm_crtc.c though. To avoid further namespace pollution
in the system wide headers create a new internal header for such drm
internal symbols.
I expect that longer-term we'll add tons more, but since my goal here
is to polish the kerneldoc that's for another day.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's not really any value in stating that no locking is needed. And
even if the comment is useful, a check for the right mutex at the
beginning of the function is better since that can't be ingored as
easily as a bit of documentation.
Note that drm_mode_probed_add in drm_crtc.c is also changed, the next
patch will move this into drm_modes.c
v2: Don't add locking WARN_ONs where it is not strictly required (i.e.
the two functions to validate/prune mode lists).
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And clean it up so that there's no kerneldoc warnings. There's still a
lot to do with this one here.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 3fbd6439e4.
This caused some strange booting lockup issues on an Intel G33
belonging to Daniel Vetter, very unusual, I was hoping Daniel
would track this down, but it looks like instead I'll have to hack
a different fix for -next.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In commit 38d5487db7, Keith explained:
This patch simply merges the two mode type bits together; that seems
reasonable to me, but perhaps only a subset of the bits should be
used? None of these can be user defined as they all come from
looking at just the hardware.
However, merging the bits means that a flag becomes sticky. It is not
possible, for example to update the mode type to remove the
DRM_MODE_TYPE_PREFERRED bit.
After a brief discussion with Dave Airlie on irc, it was agreed to
propose that change, instead of introducing another function to remove a
bit from exisiting modes type.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When using the frame packing and a single big framebuffer, some hardware
requires that we do everything like if we were scanning out the big
buffer itself. Let's instrument drm_mode_set_crtcinfo() to be able to do
this adjustement if the driver is asking for it.
v2: Use crtc_vtotal and multiply the clock by 2 instead of
reconstructing it (Ville Syrjälä)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
