It seems I missed that most ethnl_parse_header_dev_get() callers
declare an on-stack struct ethnl_req_info, and that they simply call
dev_put(req_info.dev) when about to return.
Add ethnl_parse_header_dev_put() helper to properly untrack
reference taken by ethnl_parse_header_dev_get().
Fixes: e4b8954074 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool does not expose how many lanes are used when the
link is up.
After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.
Extend ethtool to expose the number of lanes currently in use for
drivers that support it.
For example:
$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE Backplane ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
50000baseKR/Full
50000baseSR/Full
50000baseCR/Full
50000baseLR_ER_FR/Full
50000baseDR/Full
100000baseKR2/Full
100000baseSR2/Full
100000baseCR2/Full
100000baseLR2_ER2_FR2/Full
100000baseDR2/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Advertised link modes: 100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.
This would be a cleanup for next patch that would add another validation
to the new function.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To get the most out of parsing by the core, and to allow dumping
full policies we need to specify which policy applies to nested
attrs. For headers it's ethnl_header_policy.
$ sed -i 's@\(ETHTOOL_A_.*HEADER\].*=\) { .type = NLA_NESTED },@\1\n\t\tNLA_POLICY_NESTED(ethnl_header_policy),@' net/ethtool/*
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ethtool uses strict attribute validation there's no need
to initialize all attributes in policy tables. 0 is NLA_UNSPEC
which is going to be rejected. Remove the NLA_REJECTs.
Similarly attributes above maxattrs are rejected, so there's
no need to always size the policy tables to ETHTOOL_A_..._MAX.
v2: - new patch
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to get commands wire up the policies of set commands
to get parsing by the core and policy dumps.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up policies for get commands in struct nla_policy of the ethtool
family. Make use of genetlink code attr validation and parsing, as well
as allow dumping policies to user space.
For every ETHTOOL_MSG_*_GET:
- add 'ethnl_' prefix to policy name
- add extern declaration in net/ethtool/netlink.h
- wire up the policy & attr in ethtool_genl_ops[].
- remove .request_policy and .max_attr from ethnl_request_ops.
Obviously core only records the first "layer" of parsed attrs
so we still need to parse the sub-attrs of the nested header
attribute.
v2:
- merge of patches 1 and 2 from v1
- remove stray empty lines in ops
- also remove .max_attr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3af ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b3 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn pointed out that even if it's documented that
ethnl_parse_header() takes reference to network device if it fills it
into the target structure, its name doesn't make it apparent so that
corresponding dev_put() looks like mismatched.
Rename the function ethnl_parse_header_dev_get() to indicate that it
takes a reference.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for low latency Reed Solomon FEC as LLRS.
The LL-FEC is defined by the 25G/50G ethernet consortium,
in the document titled "Low Latency Reed Solomon Forward Error Correction"
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes gcc '-Wunused-but-set-variable' warning:
net/ethtool/linkmodes.c: In function 'ethnl_set_linkmodes':
net/ethtool/linkmodes.c:326:32: warning:
variable 'lsettings' set but not used [-Wunused-but-set-variable]
struct ethtool_link_settings *lsettings;
^
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_LINKMODES_NTF notification message whenever device link
settings or advertised modes are modified using ETHTOOL_MSG_LINKMODES_SET
netlink message or ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands.
The notification message has the same format as reply to LINKMODES_GET
request. ETHTOOL_MSG_LINKMODES_SET netlink request only triggers the
notification if there is a change but the ioctl command handlers do not
check if there is an actual change and trigger the notification whenever
the commands are executed.
As all work is done by ethnl_default_notify() handler and callback
functions introduced to handle LINKMODES_GET requests, all that remains is
adding entries for ETHTOOL_MSG_LINKMODES_NTF into ethnl_notify_handlers and
ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where
needed.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement LINKMODES_SET netlink request to set advertised linkmodes and
related attributes as ETHTOOL_SLINKSETTINGS and ETHTOOL_SSET commands do.
The request allows setting autonegotiation flag, speed, duplex and
advertised link modes.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement LINKMODES_GET netlink request to get link modes related
information provided by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl
commands.
This request provides supported, advertised and peer advertised link modes,
autonegotiation flag, speed and duplex.
LINKMODES_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
