While going through the whole interface opening logic in my head I was
consistently bothered by the condition checking whether there was only
one interface of type NODE/COORD opened at the same time. What actually
bothered me was the fact that in one case we would use the wpan_dev
pointer directly while in the other case we would use the sdata pointer,
making it harder to differentiate both. In practice the condition should
be straightforward to read. IMHO dropping the wpan_dev indirection
allows to clarify the check.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221026093502.602734-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
The current filtering level is set on the first interface up on a wpan
phy. If we support scan functionality we need to change the filtering
level on the fly on an operational phy and switching back again.
This patch will move the receive mode parameter e.g. address filter and
promiscuous mode to the drv_start() functionality to allow changing the
receive mode on an operational phy not on first ifup only. In future this
should be handled on driver layer because each hardware has it's own way
to enter a specific filtering level. However this should offer to switch
to mode IEEE802154_FILTERING_NONE and back to
IEEE802154_FILTERING_4_FRAME_FIELDS.
Only IEEE802154_FILTERING_4_FRAME_FIELDS and IEEE802154_FILTERING_NONE
are somewhat supported by current hardware. All other filtering levels
can be supported in future but will end in IEEE802154_FILTERING_NONE as
the receive part can kind of "emulate" those receive paths by doing
additional filtering routines.
There are in total three filtering levels in the code:
- the per-interface default level (should not be changed)
- the required per-interface level (mac commands may play with it)
- the actual per-PHY (hw) level that is currently in use
Signed-off-by: Alexander Aring <aahringo@redhat.com>
[<miquel.raynal@bootlin.com: Add the third filtering variable]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20221007085310.503366-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable ret is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the net namespace when creating SoftMAC interfaces. This
is important if the namespace at phy layer was switched before.
Currently we losing interfaces in some namespace and it's not possible
to recover that.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the mtu size of 802.15.4 interfaces. The current
setting is the meaning of the maximum transport unit with mac header,
which is 127 bytes according 802.15.4. The linux meaning of the mtu size
field is the maximum payload of a mac frame. Like in ethernet, which is
1500 bytes.
We have dynamic length of mac frames in 802.15.4, this is why we assume
the minimum header length which is hard_header_len. This contains fc and
sequence fields. These can evaluated by driver layer without additional
checks. We currently don't support to set the FCS from userspace, so we
need to subtract this from mtu size as well.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The callback "create" and "parse" from header_ops are called from
netdev core upper-layer functionality, like af_packet. These callbacks
assumes big endian for addresses and we should not introduce a special
byteordering handling for ieee802154 over af_packet in userspace.
We have an identical issue with setting the mac address which also
assumes big endian byteordering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups needed_headroom, needed_tailroom and hard_header_len
fields for wpan and lowpan interfaces.
For wpan interfaces the worst case mac header len should be part of
needed_headroom, currently this is set as hard_header_len, but
hard_header_len should be set to the minimum header length which xmit
call assumes and this is the minimum frame length of 802.15.4.
The hard_header_len value will check inside send callbacl of AF_PACKET
raw sockets.
For lowpan interfaces, if fragmentation isn't needed the skb will
call dev_hard_header for 802154 layer and queue it afterwards. This
happens without new skb allocation, so we need the same headroom and
tailroom lengths like 802154 inside 802154 6lowpan layer. At least we
assume as minimum header length an ipv6 header size.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current header_ops callback structure of net device are used mostly
from 802.15.4 upper-layers. Because this callback structure is a very
generic one, which is also used by e.g. DGRAM AF_PACKET sockets, we
can't make this callback structure 802.15.4 specific which is currently
is.
I saw the smallest "constraint" for calling this callback with
dev_hard_header/dev_parse_header by AF_PACKET which assign a 8 byte
array for address void pointers. Currently 802.15.4 specific protocols
like af802154 and 6LoWPAN will assign the "struct ieee802154_addr" as
these parameters which is greater than 8 bytes. The current callback
implementation for header_ops.create assumes always a complete
"struct ieee802154_addr" which AF_PACKET can't never handled and is
greater than 8 bytes.
For that reason we introduce now a "generic" create/parse header_ops
callback which allows handling with intra-pan extended addresses only.
This allows a small use-case with AF_PACKET to send "somehow" a valid
dataframe over DGRAM.
To keeping the current dev_hard_header behaviour we introduce a similar
callback structure "wpan_dev_header_ops" which contains 802.15.4 specific
upper-layer header creation functionality, which can be called by
wpan_dev_hard_header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the default minimum value of frame_retries to 0 and
changes the frame_retries default value to 3 which is also 802.15.4
default.
We don't use the frame_retries "-1" value as indicator for no-aret mode
anymore, instead we checking on the ack request bit inside the 802.15.4
frame control field. This allows a acknowledge handling per frame. This
checking is done by transceiver or inside xmit callback of driver layer.
If a transceiver doesn't support ARET handling the transmit
functionality ignores ack frames then, which isn't well but should not
effect anything of current functionality.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we currently change the mac address inside the wpan interface while
we have a lowpan interface on top of the wpan interface, the mac address
setting doesn't reach the lowpan interface. The effect would be that the
IPv6 lowpan interface has the old SLAAC address and isn't working
anymore because the lowpan interface use in internal mechanism sometimes
dev->addr which is the old mac address of the wpan interface.
This patch checks if a wpan interface belongs to lowpan interface, if
yes then we need to check if the lowpan interface is down and change the
mac address also at the lowpan interface. When the lowpan interface will
be set up afterwards, it will use the correct SLAAC address which based
on the updated mac address setting.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Tested-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds ieee802154_stop_device for preparing a utility function
to stop the ieee802154 device.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a workaround for using the new nl802154 netlink
interface with the old ieee802154 netlink interface togehter. The
nl802154 currently supports no access for llsec layer, currently there
are users outside which are using both interfaces at the same time. This
patch adds a necessary call when addresses are updated.
Reported-by: Simon Vincent <simon.vincent@xsilon.com>
Suggested-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no need to init res with zero, res can be unused but then we
returning zero and not res.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the hardware setting before calling the driver start
callback which activates the receive handling. The hardware setup
contains settings like address filtering which should be setup before
activate the receive handling on the transceiver. These setting are
protected by ieee802154_check_concurrent_iface check. This means we
need to set these registers once before calling drv_start and can't
be overwritten by other interfaces.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch flushs the workqueue which is currently used for xmit_sync
callback before calling stop driver-ops. Flush the queue will ensure all
pending tx frames are transmitted.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The interframe spacing timer is a per phy definition and is part of a
ieee802154_local structure. If we have possible multiple interfaces
ifdown one interface then the timer should not be cancled. First if the
last interface is down and the receive handling is stopped we should be
sure that the interframe spacing timer isn't run anymore.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This call was used before we aligned our code with the wireless code base. We
are wanted to handle this in the err: code path. Which would actually not work
because the WARN_ON() macro would reset the res value to 0 and thus we would
never hit err:. Removing it makes the code do what we actually intend.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the virtual interface structure from sub if data
struct, because it isn't used anywhere. This structure could be useful
for give per interface information at softmac driver layer. Nevertheless
there exist no use case currently and it contains the interface type
information currently. This information is also stored inside wpan dev
which is now used to check on the wpan dev interface type.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Refuse to allow setting an EUI-64 group address as an interface
address, as those are not valid station addresses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
->ndo_do_ioctl() can be entered with the rtnl lock already held,
for example when sending a wext ioctl to a device (in which case
the rtnl lock is taken by wext_ioctl_dispatch()), but
mac802154_wpan_ioctl() currently unconditionally takes the rtnl
lock on entry, which can cause deadlocks.
To fix this, bail out of mac802154_wpan_ioctl() before taking the
rtnl lock if the ioctl cmd is not one of the cmds we implement.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the mib lock. The new locking mechanism is to protect
the mib values with the rtnl lock. Note that this isn't always necessary
if we have an interface up the most mib values are readonly (e.g.
address settings). With this behaviour we can remove locking in
hotpath like frame parsing completely. It depends on context if we need
to hold the rtnl lock or not, this makes the callbacks of
ieee802154_mlme_ops unnecessary because these callbacks hols always the
locks.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will use atomic operations for sequence number incrementation
while MAC header generation. Upper layers like af_802154 or 6LoWPAN
could call this function in a parallel context while generating 802.15.4
MAC header before queuing into wpan interfaces transmit queue.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the pib lock which is now replaced by rtnl lock. The
new interface already use the rtnl lock only. Nevertheless this patch
will fix issues while using new and old interface at the same time.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes an issue to set address configuration with ioctl.
Accessing the mib requires rtnl lock and the ndo_do_ioctl doesn't hold
the rtnl lock while this callback is called. This patch do that
manually.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Matteo Petracca <matteo.petracca@sssup.it>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This code is based on commit 6bab2e19c5
("cfg80211: pass name_assign_type to rdev_add_virtual_intf()")
This will expose in sysfs whether the ifname of a IEEE-802.15.4
device is set by userspace or generated by the kernel.
We are using two types of name_assign_types
o NET_NAME_ENUM: Default interface name provided by kernel
o NET_NAME_USER: Interface name provided by user.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the checking of different mac phy depended values by
handling depended mac settings per hw support flag in one condition.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the handling for checking on multiple node type
interface to the corresponding concurrent iface check function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a check for concurrent interfaces while calling
interface up. This avoids to have different mac parameters on one phy.
Otherwise it could be that a interface can overwrite current phy mac
settings which is set by an another interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for setting an extended address while
registration a new interface. If ieee802154_is_valid_extended_addr
getting as parameter and invalid extended address then the perm address
is fallback. This is useful to make some default handling while for
example default registration of a wpan interface while phy registration.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This parameter was grabbed from wireless implementation with the
identically wireless dev struct. We don't need this right now and so we
remove it. Maybe we will add it later again if we found any real reason
to have such parameter.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the depracted IEEE802154_DEV to the new introduced
NL802154_IFTYPE_NODE types. There is a backwards compatibility to have
the identical types for both enum definitions. Also remove some inlcude
issue with "linux/nl802154.h", because the export nl_policy inside this
header it was always necessary to have an include of "net/rtnetlink.h"
before. The reason for this is more complicated. Nevertheless we removed
this now, because "linux/nl802154.h" is the depracted netlink interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new interframe spacing time handling into mac802154
layer. Interframe spacing time is a time period between each transmit.
This patch adds a high resolution timer into mac802154 and starts on
xmit complete with corresponding interframe spacing expire time if
ifs_handling is true. We make it variable because it depends if
interframe spacing time is handled by transceiver or mac802154. At the
timer complete function we wake the netdev queue again. This avoids
new frame transmit in range of interframe spacing time.
For synced driver we add no handling of interframe spacing time. This
is currently a lack of support in all synced xmit drivers. I suppose
it's working because the latency of workqueue which is needed to call
spi_sync.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a netdev notifier for interface renaming. We have a name
attribute inside of subif data struct. This is needed to have always the
actual netdev name in sdata name attribute.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of always re-lock the iflist_mtx at multiple interfaces we lock
the complete for each loop at start and at the end.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is just a cleanup to name the temporary variable for
protected list for each loop as tmp.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch move the iface unregistration into iface.c file to have
a behaviour which is similar like mac80211. Also iface handling should
be inside iface.c file only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a netif_running check while trying to change the address
attributes via ioctl. While netif_running is true these attributes
should be only readable.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the setting of dev_addr on a monitor device. This
address should be zero. A monitor should only sniff and send raw frames
out. The address should be never used by upper layers and receiving
frame parsing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an iftype argument to the wpan_dev. This is needed to
get the interface type from netdev ieee802154_ptr. The subif data struct
can only accessible in mac802154 branch.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the mac_params from subif data struct. Instead we
manipulate the wpan attributes directly.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves all mac pib attributes into the wpan_dev struct.
Furthermore we can easier access these attributes over the netdev
802154_ptr pointer. Currently this is only possible over a complicated
callback structure in mac802154 because subif data structure is
accessable inside mac802154 only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the af_ieee802154 defines and use the
IEEE802154_EXTENDED_ADDR_LEN. We should do this everywhere in the
802.15.4 subsystem because af_ieee802154 should be normally an uapi
header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adding support for a perm extended address. This is useful
when a device supports an eeprom with a programmed static extended address.
If a device doesn't support such eeprom or serial registers then the
driver should generate a random extended address.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the ieee802154_be64_to_le64 to have a similar
function like ieee802154_le64_to_be64 only with switched source and
destionation types.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>